Questions & Answers - Recent activity in Buick

Answered: Went through the the install and the car wont start and the key wont start it either?

Mon, 20 Jan 2025 08:42:16 +0000

Hello,

A few questions to help me better assist you:

Is the vehicle a push button start or a key start?

What was installed in the vehicle? T-harness? Module?

What is the S/N to the module?

Best regards.

Evo-one 2006 rendezvous no yellow light in programming

Fri, 10 Jan 2025 22:02:34 +0000

Ign on - Blue shuts off red comes on but red does not start flashiing to be able to turn key to start for yellow to come on. When red comes on solid the blue starts flashing but is dim. Red never flashes. Talked to tech support said to try starting when red light comes on instead of waiting for red flashing. Still just does the above. I have Reset, flashed 70.18, started and held in start postion and above repeats. He did say to test purple pin 2 and should be 1.5v. It is .23v and I have seen it fluctuate up to 1.2v while lock/unlock is pressedn etc. I have check every single fuse, put on battery charger, cleaned batt terminal, wiggled wires and still does the above voltage fluctuations. Could it be faulty module? Which I've never had happen in over 15ys of using fortin. Strange the blue light flashes dim after red comes on. Could it be the low voltage on obd pin #2? I've never had on issue with the pk3. Factory radio. No signs of anything aftermarket being installed to disrupt obd2 signal. Obd2 plug in code reader communicates fine and no codes present

Answered: 2020 Buick encore installation clarification

Wed, 22 Nov 2023 12:08:46 +0000

Hello,

1.On page 4(wiring diagram) of guide #77331, shows to make a connection between the light blue wire and light blue/black wire. Do these need to be spliced together? What is the reason for this?

- If your module was made before 2019 yes, if it was made after 2019 no. Fabrication date is written on the back.

2. Also, wondering what start/stop external control means?

- This is for a 3rd party device to control the evo, in your case you will not need it.

3. Are the good hood pins/ valet switch required for the function of the module?

- If the vehicle is equipped with an oem hood pin, refer to your vehicle specific guide to see if the evo covers it through data. If no then it is strongly recommended to install a hood pin for saftey reasons. It will still function without that connection.

Best regards.

Commented: evo-gmt1 no red light no start

Mon, 12 Dec 2022 20:16:30 +0000

It said it was completed

Answered: OEM remote start not working. Can I use the Evo All without the OEM Alarm/Remote Start?

Tue, 20 Sep 2022 09:18:51 +0000

Yes, the evo all can do remote start and alarm on this vehicle.

However, seeing as your vehicle has an issue to begin with, it may just have the same issue when trying to get the evo-all to work as well. Something to keep in mind.

Best Regards.

Answered: 01 Buick Lesabre ground while running wire location

Fri, 26 Nov 2021 10:07:52 +0000

What module(s) are you installing?

Ground while running is normally found on the remote starter module and is connect to the same wire on the bypass module.

It is not a wire in the vehicle.

Commented: evo-one quickly change bulbs and not respond to a programmable

Sat, 06 Nov 2021 18:14:53 +0000

https://youtu.be/fX4jZex5_Wo

Answer selected: 2017 Encore brake pedal is not recognised by the module

Wed, 29 Sep 2021 11:44:25 +0000

What is the S/N number on the back of the module?

Commented: RF912 KIT SOUND

Thu, 12 Aug 2021 11:09:05 +0000

I replaced by duracell but still the same

Answered: On bypass programming options, should I choose oem remote or aftermarket?

Mon, 05 Jul 2021 08:52:00 +0000

For an install such as this I would suggest not using the wizard mode as it will not be able to set it up the way you want.

I would switch to pro mode (click gear in upper right hand corner of the flm program and click "go to pro mode"), Then select the appropriate data link protocol (if applicable) and enable option A1 through A11 & C1. All other options should be left in there default position.

Answered: OL-RF-52-SST no LED for remote programming with EVO ONE

Thu, 01 Jul 2021 10:18:03 +0000

The solution here was a master reset of the unit. Once that was done, the antenna workled as it should and I was able to program the remotes. Everything is tested and working as of today.

Thanks for all of the help here.

Answered: Buick encore 2020

Tue, 02 Mar 2021 16:23:22 +0000

En partent, si vos module sont dater de 2014, il ne seront pas programmable au flash link.

E5 cest seulement pour les modules avec les dates indiquer dans le guide.

Answered: Few Qs about Remote while running, Unlock after disconnect, supermarket mode?

Tue, 26 Jan 2021 09:14:18 +0000

1- no thats the nature of the beast for GM flip keys.

2- no, because this is what your car does when you turn it off with the key as well. If it is possible to disable the unlock on key off it would be in your owners manual.

3- yes, its called idle mode but in order for your to be able to use it you would need an rf kit, it will not work with your oem remote in this particular vehicle.

Answered: EVOALL not registering car starting on program of module

Fri, 08 Jan 2021 12:01:53 +0000

If it is not going to red, it is not reading the key. The vehicle needs to "request" the key in order for the evo to capture it.

1. Battery needs to be out of key

2. No other key in the car

3. Close door, open door, start the programming process

4. now put the key in the cup holder.

Do not leave key in cup holder. The vehicle will simply stop requesting to see the key if it simply always sees it.

Commented: CAN BUS PROBLEM

Wed, 11 Nov 2020 12:08:07 +0000

So no hope ? Any device can be used to solve this ?

Commented: CAN BUS Remains Live

Tue, 10 Nov 2020 09:30:16 +0000

Hi, any update for the problem

Answered: Rfk-912 antenna

Mon, 12 Oct 2020 09:19:26 +0000

no updates

Commented: Rfk 912 antenna

Sat, 10 Oct 2020 18:02:08 +0000

Hello, any update came to solve antenna power saving mode and keep it constantly running ?

Answered: Remove Remote link from antenna

Mon, 03 Aug 2020 10:37:15 +0000

If you friend still has the 942 antenna and his own remotes, simply reprogram HIS remotes 2 times each. The module will keep in memory 4 remotes. reprogramming the remotes a couple of times will knock out your remote from his starter.

Closed: current device can not be flashed anymore evo-GMT1v2 chevrolet

Mon, 27 Jul 2020 09:14:43 +0000

how to fix that i can`t flash the device anymore?

is there a reset or something for this?

Closed: device cannot be flashed anymore.

Mon, 13 Jul 2020 08:37:53 +0000

The current device cannot be flashed anymore.

Service number

001A07051773

Answered: Buick regal 2016 rf912 lock & unlock not work

Mon, 15 Jun 2020 14:02:56 +0000

What is the S/N to the module?

Answered: shock sensor activation

Wed, 10 Jun 2020 15:44:57 +0000

There is no direct plug in for the shock sensor on the EVO-ALL.

The RFA2A is only for an RF-KIT.

Once option G is enabled, and only when option G is enabled, both trigger wires of the shock sensor need to be connected to the PURPLE wire of the 20pin connector. The purple wire is a dual stage shock sensor input when option G is on. When option G is NOT on, it is a unlock input.

If you want to use the EVO-ALARM feature on the evo-all, please follow this guide for guidance on what the inputs/outputs will be once the EVO-ALARM option G is enabled. https://cdn02.fortin.ca/download/16221/16221.pdf

Closed: Disregard: Evo One no red LED during programming

Sat, 06 Jun 2020 08:20:43 +0000

UPDATE- Apparently a module has failed on the truck, so this appears to be unrelated to the EVO install. Closing the post.

2005 Rainier, EVO One. Wired per diagram. Module had FW 70.18, flashed to 70.39 since I'm using an RF kit OL-RF-52-SST.

Followed vehicle-specific programming per guide 23261 rev 20190514:

1) Hold program button, plug in power connector.

2) Wait for solid blue LED, release button. Blue LED remains on.

3) Plug in 20-pin harness and RF antenna harness

4) Key on, blue LED out, no red LED. No LED at all.

Read & followed this post for the same year Chevy truck:

2005 Alavanche can’t get the red led to come on during programming

Reset per the linked post in the above post:

1) Flashed v. 0.99

2) Disconnected from flasher, connected power plug (Red/Yellow/Blue LEDS on solid)

3) Disconnected main plug.

4) Reflashed to 70.18

5) Setting protection is not on

6) Reset by following above-

7) Hold programming button

8) Plug in power connector, wait for solid blue LED, release button

9) Blue LED off, red LED on then off, yellow LED on solid. This is where the red LED is suppsed to flash.

Comment edited: Horn alarm not workin, light problem

Tue, 03 Sep 2019 12:12:04 +0000

which color wire and which no, A5 isn't it ?

Answered: 2006 Buick Rendezvous - Car stays running intermittently

Thu, 21 Mar 2019 09:31:50 +0000

Should redirect this question to Compustar...

Answer selected: Buick Rendezvous - int-sl does not supprt trunk release. Any options?

Wed, 20 Mar 2019 21:05:19 +0000

You can hook up the analog trunk release of your remote starter to the vehicle's trunk release trigger wire, White/Black (-) on the BCM's smallest connector in the center console. doors will need to be unlocked first before this wire is triggered, (All wires will need to be tested with a digital multimeter to locate the correct wire BEFORE any connections are made.

Answered: 2006 Buick Rendezvous remote starter - Where do all of these ignition wires go?

Tue, 19 Mar 2019 12:05:10 +0000

You are supposed to test every wire you are connecting to with a digital multimeter to make sure you are connecting the correct wire from the remote starter to the vehicle.

Answered: EVO-ALL Doesn't lock unlock when input toggles

Mon, 18 Feb 2019 09:45:21 +0000

Unit looks setup ok aside from A3 being off.

Flash firmware 70.18 and try it. Shouldnt have to reprogram it.

Answered: EVO-All and Remote Start - No Red Light no Start

Sun, 10 Feb 2019 15:30:45 +0000

The service number on my Fortin EVO-ALL is 001A06 785313. The remote starter I am using is an EasyGuard EC002.

I did some more troubleshooting this weekend, and here is what I found.

1. I hooked up a relay using ACC to generate the GWR signal to the Fortin. I can measure with a multimeter that the voltage on the GWR input to the EVO-ALL drops from 12V to 0V when I remote start the car. The yellow light turns on, but the red light on the Fortin EVO-ALL never turns on and the car does not start.

2. If I leave a key in the ignition, and remote start the car, the car starts fine and stays running but the red light on the EVO-ALL still never comes on.

3. If I test with the factory remote by pressing lock 3X, the car starts.

4. I ran wires between GND and GWR with a mechanical toggle switch. I can flip the switch and see the voltage changes from 12V to 0V, but the red light on the EVO-ALL never comes on.

Could I have a defective EVO-ALL? What else can I do to troubleshoot the GWR issue?

2001 Buick Park Avenue Locks Wake up Dome Lights and Won't Shut off

Sun, 23 Dec 2018 14:42:18 +0000

Starter works and door locks work fine, however, when the doors are locked with the RFK942 the dome lights come on in the car and stay on in the car. Horn honks 3x indicating door is open. I've tested all door pins and none show open. What could it be?

Answered: 2017 Buick Enclave programming sequence goes fine but no key data decryptor.

Tue, 27 Nov 2018 16:18:54 +0000

Just saw you did a dcrpyor for a 2015 and it was successful?

Answered: 2012 buick regal gs push to start 6spd manual clutch bypass help

Mon, 09 Jul 2018 08:34:50 +0000

Clutch bypass is listed in evo-one guide: http://cdn.fortin.ca/download/58711/evo-one_ig_reg_bi_gm_lacrosse-regal-srx-cruze_pts_a_58711.pdf

requires a resistor.

Answer selected: 1991 Buick Park Avenue - What is correct number of flashes after programming SL2?

Mon, 18 Jun 2018 16:45:16 +0000

Five is the same mode as 3 but was added later after the guide was published.

Answered: ouvrir ma buick vérano 2014 une fois démarrée

Mon, 09 Apr 2018 10:15:34 +0000

Nous offrons pas le 3xlock sur ce véhicule pour cette raison. Une fois démarrer à distance (et même démarrer avec la clé), la télécommande d'origine cesse de fonctionné.

https://fortin.ca/fr/vehicles/buick/verano/2014-standard-key/

Typiquement, il faut jumelé le démarreur avec un Kit-RF: https://fortin.ca/fr/technology/rf_kits.html

Answer selected: I am needing more detailed information/instructions on the wiring diagrams.

Thu, 01 Mar 2018 09:48:46 +0000

Looking at the website here: http://fortin.ca/en/vehicles/buick/lucerne/2006-standard-key/ INT-SL+ is not listed as a supported module for your vehicle, Which explains why you cannot find the installation guide for it as it does not exist. For that vehicle you would want either evo-all or evo-one.

In regards to the starter wire not being shown... Their is a very simple answer for that, this vehicle does not use a starter wire at the ignition switch. It uses logic to crank the vehicle, when ign and acc are powered and acc drops the vehicles computer cranks the engine.

Answered: I can remote start my 2016 Encore but can not shut it off with remote or key

Mon, 29 Jan 2018 09:36:04 +0000

This is normal operation of the unit. As stated on our website the oem remote no longer works once its remote started.

http://fortin.ca/en/vehicles/buick/encore/2016-standard-key/

Edited: Evo-all gtm1v2 shut after 1 sec

Sun, 21 Jan 2018 07:05:12 +0000

Buick regal start and shut after one sec, decrypted correctly, car start with 3x loch, but shut always after 1 sec. Reprat all for one more time and stop. I have reset all, reprogrammed, redecrypted, but alway egual.... I'm goin crazy.... Please help

Comment edited: Opel insignia start and shut in 1 sec. Egual at buick regal 2014

Wed, 17 Jan 2018 11:07:48 +0000

Thanks, but with all this status on if i press the 3x lock nothing happend, i have readed the hood switch option can be the problem, but in the same time i have removed also the other option. i can reenable all but no A11, can be ok?

And where i can download the installation guide? i see only a guide with 8 page and in the page 8 is the displaimer....

Comment edited: Evo-One responds to commands over Fortin RF642W kit poorely.

Wed, 01 Feb 2017 12:08:04 +0000

Nothing???

Again, today I go out to my car and hit unlock THREE TIMES!!! just to get the EVO to send one successful unlock command while standing less than 10ft from the window mounted antenna. This is absolutely unreliable performance.

It's sounding like my only option is to rip the EVO-ONE and the Fortin 2way RF kit out and replace it with a Compustar or something that isn't Fortin made. Thank goodness I still have time to return the Fortin hardware.

Answered: Compustar-CS800S-With-700R Remote-Activate timer button sequence

Tue, 31 Jan 2017 14:56:26 +0000

This is something you would want to ask compustar.

Comment edited: EVO-ONE is preventing my physical key from starting my car.

Thu, 12 Jan 2017 23:20:53 +0000

Pulling the key out and putting it back in doesn't do the trick. I tried a gazillion times...

I only have one accessory wire wired and it's the orange. Everything seems to work(outside of the RF remote command problems I'm having...I have another open question on that one) otherwise.

The very first time this happened, my wife had remote started it from inside a store. She got outside and the car wasn't on. She stood outside the car and tried it again to see if the EVO was working and it still wouldn't activate the car's starter. So she hopped in the car and put the key in and it wouldn't start. After many tries and probably about 10mins time passing, she got it to start. When she explained this, I just figured the starter solenoid was going as this seemed pretty textbook starter solenoid.

Why would it trigger the lockout from just trying to remote start it? I haven't had that instance happen since that day either.

Thank you for the assistance.

Answer edited: Wired exactly as the install guide said but car won't even try to crank.

Mon, 12 Dec 2016 23:49:55 +0000

Diagram says to not use the white wire from the 6pin power harness. This wrong. You must wire the white wire on the 6pin power harness to ignition 2 on this car. Function: 2 Mode: 1 needs to be selected in the starter settings because the white wire is a programmable wire so it needs to be programmed to the right setting.

The diagram mentions you must program this car for "Tachless only" mode as well but this is false since it can get a tach signal from the bypass. You can indeed use the start with tach settings and do NOT have to use tachless!

That is the only missing wire and settings that needs to be done to make this car work(the car will start via tachless if you really prefer that).

Comment edited: Does the Evo-One work as a remote starter for a 2003 Buick Century?

Mon, 05 Dec 2016 12:48:19 +0000

So the diagram I linked above is all I need to wire for both bypass, remote start, door locks, and trunk control? I realize my OEM remote will not work with 3x lock to start the car thus an RF kit is needed.

Answer selected: CM800-S Options Programming using Remotes

Sat, 19 Nov 2016 15:39:02 +0000

Questions regarding your Compustar piece should be directed to Compustar/Firstech support.

Thank you.

Comment edited: CM800-S 1995 Buick Park Avenue - Backup Lights when started by Remote

Fri, 18 Nov 2016 01:19:28 +0000

Excellent idea, going to use the GWR (Ground While Running) wire of the CM800-S, to fire a SPDT relay sending 12V+ to the BackUp Light circuit. When the remote start (GWR) wire is deactivated, the BackUp lights will turn off. Thanks.

Edited: CM800-S 1995 Buick Park Avenue - Door Unlock/Lock

Tue, 25 Oct 2016 03:13:12 +0000

Door Unlock/Lock

The following are from WireColor.com ...

Lock - 95. Red/Black Driver's Kick
Unlock - 99. Orange/Black Driver's Kick

These colors are incorrect, these are for 1996, the correct colors are White and Light Blue for 1995's, can be found at the Door Lock/Unlock Switch or in the bundle of wires Driver's side under carpet, above Rocker area.

http://www.commandocaralarms.com/wiring/1994-1995/buick/parkavenue/331.html
This link has the correct colors in a chart.

Regarding the quest for information regarding the subject of Door Locks, the 1991-1996 Buick Park Avenue's ALL HAVE (+) DOOR LOCK/UNLOCK configuration at the switches. [However the Remote Accessory Control sends (-)]

I built and tested a bank of two standard relay's for the purpose of Door Lock/Unlock which is operational from CM800-S Remotes.

The CN3 wires to connect to the relay's are #4 Blue (-) Unlock and #5 Blue/Black (-) Lock . The car wire colors are White (Unlock) and Light Blue (Lock), these are the same wires that run to the Lock/Unlock Relay, under the carpet at front of Driver's seat.

However the relay's that I set up to operate the doors do not turn on the interior lights, and unlock opens all the doors, not just Driver's door on the first pulse, so going to try and get the CM800-S (-) pulses connected to the correct wires at the Remote Accessory Control / LH Door Isolation Relay area to gain some functionality.

The CM800-S Trunk Release (-) attached to the dash Trunk Release Switch (car wire Black), unlocks the doors at the same time as the trunk is opened, which is what the installation details show as correct.

Thanks for your help.

Comment edited: CM800-S Install 1995 Buick Park Avenue

Fri, 21 Oct 2016 00:11:28 +0000

Thanks, ran the park light wire out to the Driver's Side Park light, tan wire/white stripe, all park lights working now.

Regarding Trunk Release, hooked up Trunk Release Black At Trunk Switch Driver's Side dash. Trunk is working with CM800-S remote now.

Thanks for your responses.

Rap non-fonctionnel

Thu, 20 Oct 2016 07:29:26 +0000

Installer FSA-206 et EVO-ALL v70.23 sur Buick Verano, tout fonctionne bien sauf que la radio continue de fonct. après démarrage.

Regal 2010 on EVO ALL with THAR-GM1V2 programming fail

Mon, 16 Mar 2015 02:30:12 +0000

My car is Regal 2010 flip key with auto transmission

I got EVO-All and THAR-GM1V2, everything is well installed. Firmware is upgraded to latest version of this car.

When I follow the programming guide <evo-all_(firmware_4.18_hardware_6_and_more_required)_thar-gm1_v2_(t-harness).rev-20130509> step4, that is a long step, some actions requires to be finished within 5 second.

When I finish step4 within 5 seconds, the yellow light keeps on and red light flash rapidly, which is differenct as guide shows.

Please help. What should I do?

Add more info

I want to use it with oem remoter.

The issue I described above was follow the programming guide. And it was not success as I mentioned.

Then I tried to follow the decryptor guide. It's also difference as the guide shows. In the guide the last status should be blue light flash rapidly then remove the key blue light flash slowly. In my case the blue light keep light on before and after remove the key.

However I still finish the whole process with flash link updater. When I reconnect the 4-Pin connector back after all the remaining connector, both red, yellow and blue light keep flash. I don't know whether the status is correct or not.

When I push unlock button 3 times, nothing happen.

Any more info needs, please let me know.