Questions & Answers - Recent activity in Chrysler

Answered: 2014 Dodge Caravan with your remote start & want to remove it & install in my 2019 Dodge caravan.

Fri, 06 Mar 2026 13:13:31 +0000

Hello,

Yes you should be able to transfer it over since the vehicle was unchanged electronically from 2011-2020. If you provide me the S/N number on the back of the unit I can confirm this for you.

This would be the in vehicle programming guide (page 6): https://cdn02.fortin.ca/download/99231/EVO-ALL_IG_RTS-WIN_Town-GCaravan_2011_A_99231.pdf

Best regards

Commented: Unable to complete Step 5 Blue light doesnt flash at all

Mon, 26 Jan 2026 13:40:23 +0000

Awesome glad that got it going for you!

Answered: compatability with 2009 PT Cruiser

Sun, 25 Jan 2026 18:35:56 +0000

Did you ever figure this out?

Commented: Reset flash limit on EVO-ALL S/N 001A06 494478

Mon, 14 Apr 2025 08:32:06 +0000

The unit is flashed with firmware 79.24, so it could be used on older (2000-2010) toyota/lexus key start vehicles. https://cdn02.fortin.ca/download/5801/EVO-ALL_toyotalexus_regconfig_cahierD20120813.pdf

It would be for bypass only, you'd still need a remote starter.

You can manually reset the options back to default following this in vehicle reset procedure: https://cdn.fortin.ca/en/download/61931/61931.pdf

But you will not be able to make any changes using the flash link for this module.

Best regards.

Answered: need reset

Tue, 03 Dec 2024 08:14:10 +0000

Hello,

Modules dated 2015 and older cannot be configured or reset, this module dating from 2015 falls into that category.

Best regards.

Answered: Chrysler Pacifica & int-sl+ problem

Fri, 08 Nov 2024 08:03:04 +0000

Hello,

Sounds like the int-sl+ is not being activated by your remote starter if the red led does not turn on when remote starting.

If that is the case then you would want to verify the operation of the ground while running from the remote starter to the int-sl+.

Best regards.

Commented: INT-SL+intalling on 2002 Chrysler 300M What Remote Stater can I us ?

Tue, 08 Oct 2024 11:36:33 +0000

Thanks Derek

Commented: INT-SL+ not programming on Chrysler

Thu, 26 Sep 2024 16:13:18 +0000

No it doesn't. I didn't wire the ground while running though maybe that's it ... I'll try it this weekend and see if that does it.

thanks

Answered: Evo-One J1850

Thu, 12 Sep 2024 15:39:16 +0000

Hello,

You could try flashing firmware 74.22 into the bypass of the evo one and then following the programming of the evo-all guide. No guarantee it will work but it would be worth a shot.

Set up the module and re select another vehicle such as a 2006 300. You will then have access to the 74.22 fw.

https://cdn02.fortin.ca/download/9501/EVO-ALL_ChryslerDodgeJeep_cahierV2K20130527.pdf

Best regards.

Answered: EVO ALL Wiring diagram/pinout

Thu, 08 Aug 2024 13:05:17 +0000

Hello,

On the evo-all black 4 pin connector. Red is 12v, black is ground.

Best regards.

Answered: 2012 Chrysler 300 will not recognize Fob without the battery installed in Fob

Mon, 15 Jul 2024 09:07:51 +0000

Hello,

Try moving the fob around the pts button, also ensure that the red connector is plugged into the evo.

If the issue persists then this would indiciate that the passive rfid is not programmed in the remote. You can try another remote but if the issue persists you would need to visit a dealer to have the fob properly programmed to the vehicle.

Best regards.

Answered: programming

Sun, 31 Dec 2023 14:29:41 +0000

After doing some search looks like the unit needs to be flashed. I am going to return this and get one that is already flashed and is ready to go.

Answered: why doesn't my activation code work

Thu, 14 Dec 2023 15:30:30 +0000

Hello,

Due to the sensitivity of information associated to an activation code, please email questions regarding them to support@fortin.ca

Thank you.

Answer selected: Troubleshooting reverse lights

Tue, 21 Nov 2023 10:06:41 +0000

I know I posted this a long time ago, but in case anyone was wondering I found some wires under a bolt that was causing the short. Nothing to do with the Fortin modules

Answered: where is headlight wiring located

Tue, 13 Dec 2022 16:57:19 +0000

Hello,

On this vehicle the wire is located directly at the light switch connector on the backside of the light switch. It should bre a white/brown wire on the vehicle. From the evo-all it is the brown/white wire on the 20 pin connector and will require a 2.4k ohm resistor inline.

Best regards.

Answer selected: 2015 Chrysler 200 push to star

Wed, 30 Nov 2022 17:57:22 +0000

Hello,

Please provide the S/N number on the back of the module.

Best regards.

Answered: flash link updater

Mon, 29 Aug 2022 09:49:37 +0000

Evo modules dated 2016 and older cannot be updated via the flash link. If the manufacture date on the back of your evo refelects these year ranges, this is why it will not allow it to update.

Answered: Is it possible to use on a daily basis only the RFK without the original key to drive?

Thu, 04 Aug 2022 17:20:47 +0000

No, you must always carry the oem remote with you.

Answered: change my RFK 442 for a RFK 942?

Thu, 04 Aug 2022 17:17:47 +0000

Yes the 942 has more range.

You will need a new antenna along with the remote.

https://fortin.ca/en/products/evo_9_series/rfk942/

Answered: J ai des problemes avec mon immobilizer sur un win module avec fobyk key . Est ce que vos produits peuvent m aider

Thu, 12 May 2022 09:05:17 +0000

Non malheureusement pas. Nos modules ne remplace pas le système de immobiliser.

Answered: No luck getting it to work! please help.

Mon, 17 Jan 2022 08:58:40 +0000

If it stays solid blue when you turn the key on then there is an issue with your yellow wires.

Check the yellow are at the 20 pin connector, It should have ignition voltage key on and no voltage key off.

Commented: 2016 Chrysler T&C blue light wont flash

Sun, 09 Jan 2022 21:26:40 +0000

Yeah, used the T harness. Havnt checked power to the yellow wire.

Commented: just wondering if i can use compustar 2wshlcdr-703 on evo all?

Fri, 07 Jan 2022 18:59:49 +0000

Its a compustar rf kit a key fob lcd and 2wsh antenna...i installed evo all on my Chrysler 200 using 3x lock..

Answered: What T-Harness do i need for a 2004 Chrysler Sebring sedan?

Tue, 14 Dec 2021 16:11:36 +0000

T-harness does not exist for that vehicle.

Also the evo-all does not start that car, its just a bypass in that vehicle, you will still need a remote starter.

Hardware 6 evo-all is required.

https://fortin.ca/en/vehicles/chrysler/sebring/2004-sedan/

Commented: vehicle wont remote start

Mon, 22 Nov 2021 08:26:36 +0000

Does the any led on the unit blink at all when trying that starting sequence? If so which ones and how many times do they blink?

Answered: decipher qas completed and vech still wont statr

Sat, 20 Nov 2021 09:49:29 +0000

Please reflash and reprogram module to vehicle, it would seem that the dcryptor process did not go through 100%

Answered: Will an Evo-can work as a 3 times lock remote start on a 2013 chrysler 200

Fri, 01 Oct 2021 10:42:45 +0000

Stand alone is only available on modules that say EVO-ALL on it.

The original EVO-CHR units, not to be confused with current combo kits called EVO-CHRTX , do not support stand alone. The EVO-CHRTX kits inlcude an EVO-ALL

Commented: 05 chrysler the whole left side of the car won't lock or unlock or activate the lights

Tue, 08 Jun 2021 13:59:44 +0000

accessories are controlled the MUX wire. so check for a broken wire as well. Or maybe a a bent pin. Same for the transponder connector, ensure a healthy connector.

Commented: Why my evo all activate my check engine light on my chrysler 200 2015?

Tue, 04 May 2021 09:16:40 +0000

Which t-harness was used? The harness itself will have a sticker with the part number on it.

Answered: Push to Start Takeover without Shutdown

Wed, 14 Apr 2021 16:28:14 +0000

Takeover will not work and vehicle will shut down on brake press if a door is detected as open when the car is remote started. This is a safety in case it is remote started with a door open and a thief comes running thinking he can drive away.

Go around the vehicle and make sure all doors are fully closed.

Make sure all door triggers are 100% operational.

Answered: I can’t program chrt4 all light plinking

Wed, 31 Mar 2021 15:52:12 +0000

If all 3 lights flash at the same time while you are holding down the button and connecting black 4 pin connector, this means the module has not been flashed for the vehicle.

Please connect it to the flash link updater then flash and configure it for the vehicle its being installed into. Once this is done, re attempt in vehicle programming.

Commented: Idle Mode without an RF kit?

Fri, 19 Feb 2021 17:05:05 +0000

Noted. Thanks for the reply Robb

Answered: FACTORY ALARM COMES ON

Thu, 18 Feb 2021 08:55:03 +0000

For problem 1, turn on option D2.

For problem 2, this is normal, we do not control rap on the vehicle. It will time out after a few minutes and turn itself off.

Answered: Is RFK912 available for FlashLogic FLRSCH4?

Tue, 16 Feb 2021 08:51:32 +0000

Fortin RF kits are only tested with Fortin products. They have not been tested with competitors modules.

Answered: Do I have to connect this wire ?

Thu, 11 Feb 2021 09:53:11 +0000

if the vehicle is 2010 and less yes the connection must be done.

Commented: How to ensure silent mode (i.e. no horn honks on remote start)?

Thu, 14 Jan 2021 12:58:57 +0000

You can connect parking lights to get a visual indicator

Answered: Can the EVO-CHRT5 be reflashed for different car

Tue, 05 Jan 2021 17:19:46 +0000

It's the same firmware

Commented: P0513 code 2005 Chrysler 300c Evo All Stand Alone Connection F Everything Working.

Wed, 30 Dec 2020 16:59:32 +0000

I feel it has to do with the Long Rang RM411 remote firmware is what is causing the issue, not really a problem.

If i just use the key to remote start with 3xunlock, the code does not appear (again, no engine light, so you have to look for it to find the error code).

I feel many people may be in similar situations, but the car works fine and no MIL. It may just be a Chrysler thing. Perhaps a new updated firmware flash in the future may fix.

Answered: i bought from fortin but my unit wasnt flashed upon delivery

Thu, 19 Nov 2020 22:05:42 +0000

The flashlink updater is well worth it man. You may want to change settings a few times before you get it where it's right for you.

Also use it on another car in the future or just get it to where you want and re-sell it once you're done.

If you're in the US saw it on Amazon for $38 a while back.

Just remember to update the flashlink 4 updater itself before you flash your module.

Answered: It's perfect except one thing. heated seats. it may be working (hasn't been cold)

Mon, 09 Nov 2020 08:41:25 +0000

Heated seats in not supported on your vehicle. The options list is generic.supported features can be found in the installation guide supported features section.

Answered: Flash link not detecting my module when connected to my computer

Sat, 07 Nov 2020 18:53:58 +0000

Did you update the FlashLink first? Once you do that it should work. Make sure only the power plug is used when doing so. Hope it helps.

Commented: How to install the valet switch Evo All Standalone installation.

Thu, 05 Nov 2020 09:55:42 +0000

Thanks for the update!

Answer selected: 2005 Chrysler 300c Evo All Standalone install Chrt5 T Harness Part 3 (Solved)

Sat, 31 Oct 2020 13:08:49 +0000

This issue has now been SOLVED! Red pin D2 Yellow/Blue wire stays connected to T Harness (It's the only wire not cut, isolated or manually connected to anything else). D1 & D4 are cut and isolated using the Char5 T-Harness standalone setup. D3,D5.D6 from red 6 pin connector are manually connected to ignition switch. D3 to pin 3, D5 to pin 5, D6 to pin 4 (ignition switch)

What is the setting to open doors once in park so I don't set off the alarm or have to remember to unlock doors manually.

Also parking light connection will have to go, like to just leave lights on automatic and not have to manually turn on headlights once in the car at night.

Now looking at the guide it seems obvious. Hopefully posting this, others will have an easier install process with this amazing product.

Sad note, I noticed my water pump is on it's way out. It's original and has almost 170,000 miles on it. Will replace with Mopar part and new belt....(this is where the son in law comes in really handy). New lights replaced on HVAC console and driver seat switch and she's good.

Feels good to have done this myself. There is still an adjustment or two to get it where I want it to be....that will be tomorrow...

https://www.amazon.com/gp/product/B081821YSV/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1

The above link is the tool i used from US Amazon (just linking it, no money is being made by me). It worked better than expected and was $16.99 us dollars.

The only thing that could have been better is clear instructions on how to install hood pin and or the safey switch. I think most people don't bother cause they get an RF Kit and can put the key to on and hit the button on the side of the RF antena remote on your windshield 3 times to engage valet mode and same again to disengage. So I've read, but never tried.

Also if you guys can add not to cut D2 Yellow/Blue wire from harness with an asterix or something would probably help the average consumer (techs know how to read the diagram better).

Also want to say thanks to Derek for personally offering phone technical support once I had a multimeter in my possession. You rock buddy!

Edited: 2005 Chrysler 300c Evo All install using T Harness Chrt5 no remote start after install

Thu, 29 Oct 2020 21:30:37 +0000

My ignition wire setup as follows. 1. Purple/Orange

2. Purple/Brown

3. Pink/White (Now says Pink)

4. Pink/Green (Now says Pink)

5. LTBlue/Red

Module and RF kit (RM411) is programed and works fine. When I remote start I get a blue light for each lock press on OEM remote.

Then it unlocks and locks and get RED and YELLOW lights with bottom blue flashing I hear the chime and it tries to engage without starting.

I know I can't be the first 300c first gen owner that has had this problem, any help would be greatly appreciated. I can share the video of the starting sequence (email or onedrive link). Thanks

https://1drv.ms/u/s!AglxCUFWL4h7k_RVT52kACjno0_xIA (pic of Ignition plug)

Right click links and choose open in new window to stay in forum

Commented: Install help. Evo All Stand Alone install with T-Harness CHR5 2005 Chrysler 300c

Tue, 27 Oct 2020 23:07:52 +0000

Yes military splice is the way to go. I didn't want to have to do that, but the car will die with us or in our family anyways. I practiced on some spare wire with a dentist pick and razor blade and worked very well. Do you also recommend solder as well?

It's Beer thirty and will make some time tomorrow. On a good note this thing will be rock solid when I'm finished with it.

reprogram evo-chr to other cars

Thu, 28 May 2020 23:36:59 +0000

Is it possible to reprogram evo-chr vr firmware 2.10 (HD 6) to other cars, as evo-all?

Edited: fortin evo-chr

Tue, 26 May 2020 16:32:47 +0000

Is it possible evo-chr firmware vr. 2.10 (hd 6) reprogram on other cars, how evo-all? ??

Comment edited: 2004 Chrysler Crossfire aka Mercedes SLK

Fri, 08 May 2020 15:03:38 +0000

if you have a hardware 6 evo, firmware 4.18 is all all makes/models for older cars. And its preflashed to 4.18 out the box

help flash reset

Thu, 30 Jan 2020 09:15:25 +0000

please reset 001A07076660

can evo All 3x start a 2001 town and country van?

Sun, 19 Jan 2020 21:02:58 +0000

Hi,

Can the evo-All do stand alone 3x lock start with the oem remotes for the 2001 town and country?

I programed the unit and it stated 3x start option that I loaded, but I'm not sure what guide to use to wire into van.

Guide # 3317 shows a remote start unit used to wire up?

Is there another guide to use for stand alone 3x evo All?

Thanks,

Steve