Questions & Answers - Recent questions in Scion

Flash limit reached on a Evo One

Wed, 26 Nov 2025 02:24:45 +0000

Hello,

The Evo One via FlashLink is saying "flash limit reached". How can I have this reset so I can reflash this Evo One?

the Service no is 002B07 164158

Thanks in advanced for any help given

Could you please reset my evo all flash limit S/N 001A06 462499

Fri, 13 Dec 2024 17:00:36 +0000

Evo all S/N 001A06 462499

2015 Scion xB Evo-One, no transponder

Sat, 16 Nov 2024 20:31:59 +0000

Installing an Evo One for remote start with t-harness Toy1, vehicle has canbus, but is not equipped with a immobilizer system. Installed per guide #92261, but am not hung up on programming/key sense. Obviously I am going to use a different sequence because it will not get to the flashing blue led, there is no immobilizer (verified key has no transponder chip).

Is there another quide for 2015 xB with Canbus but no immobilizer?

Will the EVO ONE work on my 2016 Scion tC with push button start?

Tue, 12 Nov 2024 00:01:07 +0000

Hi,

I see the EVO ONE should work for my 2016 Scion tC but the trim level states standard key. The 2016 model only came with Push to start. No manual key option. Will this work? If so, which T harness should I use? Car is also manual if that matters.

Thanks

Ready Mode turns off when closing the door on a manual 2013 Scion FRS Key Start

Tue, 10 Sep 2024 23:21:50 +0000

After wiring everything correctly and triple checking all the wirings I can control lock, unlock and even engine shutoff using the mobile app but for some reason after putting the car in ready mode and closing the door the engine shuts off, and when trying to start it again using the mobile app it starts for half a second then shuts off

I tried resetting the module and reflashing multiple times and even went back to the frimware recommended in the guide but now it's saying that the decryptor's limit has been reached...

and it's still giving me the same errors

SN: 002B04 664699

EVO-ONE + START-2 in 2012 Scion IQ app door locking does not work but unlock does

Tue, 24 Jan 2023 13:08:53 +0000

I have an EVO-ONE with T-Harness and EVO-START-2 RF kit installed. The door lock data is connected from EVO-ONE to vehicle harness. The Android app communicates with the car.

Using the app to REMOTE UNLOCK the car works fine and flashes the parking lights

The LOCK command from the app flashes the parking lights, but DOES NOT REMOTE LOCK the car.

Any ideas?

Evo One flash limit reached

Sun, 08 Jan 2023 20:04:23 +0000

Evo One

SN: 002B04 252696

Remote not working to start or lock/unlock a Scion TC 2016

Fri, 16 Dec 2022 11:24:39 +0000

Just put new batteries in and remote doesn't seem to click in. Blue light flashes, then get a red at the end. Can't lock or unlock the car with remote.

Alarm setting off

Mon, 07 Mar 2022 13:08:03 +0000

I installed the EVO ONE without T-Harness and RFK411 on a 2014 Scion XD (with standard key). Sometimes after remore start, when the door is opened the alarm is set off and the remote start is halted. Option D2 was inititially turned off. I turned it on and though it improved quite a bit, it still happens every now and then. The system is wired and configured per Guide # 102241. Any help would be greatly appreciated.

trouble getting a 2016 scion ia to remote start reliably

Tue, 25 Jan 2022 14:08:49 +0000

2016 scion ia remote starting, do i need too wake up the light circuit? used an ar35 as per the instructions. also which firmware should i use with this particular model

evo-one, t harness, ar35, with the 62-rw were the parts used, all other functions on the remote work flawlessly

Get a signal but won't start

Thu, 25 Nov 2021 10:44:22 +0000

Hello I installed my Evo one about 2 year ago on my scion FRS 2013 it always worked but now for some reason it won't work after the night if I try it when at work it work but when I get home and set it up in the morning it get signal and parking light flashes but the car won't start... I have to get in the car and it work with the key.

2009 SCION XB RX AND TX CONNECTOR

Fri, 27 Nov 2020 09:08:48 +0000

I TRY USING THE 2011 + SCION XB WIRING DIAGRAM AND IT DOENST WORK

I TRYING TO WIRE FOR THE 2008 SCION XB WIRING DIAGRAM AND I CANT FIND THE RX AND TX

THERE NO CONNECTOR NEAR THE IGNITION THAT HAS THE 7 WIRE.

2011 Scion xB won’t remote start EVO ONE

Sat, 21 Dec 2019 20:38:24 +0000

No immobilizer, did not connect light blue/ black wire, module programs ok by letting go of button on blue, and the flashes blue rapidly after turning key to on.

I already tried connecting the immobilizer wire & programming again.
I already tried programming using red & blue light but that won't program.
Using Fortin guide #23001.
Not "G" key.
Verified no immobilizer/chip on key.
Won't remote start with lock 3 times on key.
Won't remote start with the MyCar app module.

unable to program evo one module for 2016 scion im ?

Mon, 16 Dec 2019 20:59:22 +0000

blue light solid while red light flashes

then i tried programing again and then the only light that flashed was the red one

2014 Scion Xb Evo Ride

Sun, 13 Jan 2019 21:40:07 +0000

I do not have the IMO and IMI wires at the ECU as stated in the connection 17 diagram.

Can I wire this in a different configuration to function similar?

Or am I looking to purchase a different product?

Do I need to wie in the Key sense?

Please help with installing EVO-All Kit for my 2016 Scion iA

Tue, 25 Dec 2018 01:41:06 +0000

I received the EVO-All KIT and already flashed the newest firmware. I just want it to be a standlone with 3 locks remote start function to work. I bought the THAR-MAZ1 to my life easier. I've read the diagram and my understanding is we have to do some wire tapping in order to make everything work. Is there a way for me to make it a standlone with 3 locks remote start to work without doing any wire tapping ?

2009 Scion TC no keysense

Mon, 24 Dec 2018 15:18:15 +0000

I'm trying to install a EVO-ONE and RF kit into a Scion tC but there's no keysense so I cannot program the module. Is there something else I can do?

2012 xB Manual Transmission.

Thu, 29 Nov 2018 16:28:14 +0000

I am interested in using the the EVO-ONE + THAR-ONE-TOY1 on my 2012 xB. It is a manual transmission, will I be able to use this setup? If so, does anything need to be done to bypass the clutch depressed switch?

evo-key programmed but wont remote start

Fri, 16 Mar 2018 17:00:37 +0000

hi, i have a 2008 scion Tc (standard key) installed crimpestopper SP-402 with Evo-key module,using data link wire

i followed the exact guide connection 1 and program 1

evo key programmed properly but when remote starting it recieves command but no crank and the evo-key led stays solid red, i also tried hard wiring it and still same result.

EVO-ONE + Scion iq w/o immobilizer

Sun, 29 Oct 2017 23:56:29 +0000

I got an EVO-ONE with a T-harness but can't get it to program correctly. I just keep getting a red light. Tech support says maybe can't program because there's no immobilizer. Anyone know if I can still install this thing and how.

2008 scion tc/evo one ftx641w

Mon, 08 May 2017 12:19:51 +0000

hi,i have few questions that im having issues with my 2008 scion Tc A/T
EVO-ONE SERICE# 002B07 164975
T-HARNESS
fortin ftx64-1W remote
ive already connected pretty much all wires needed i believe, i can remote start the car,antenna led is blinking,horn responds when unlock/lock button is press,but doors does NOT lock or unlock, i do have the purple & purple/white connected to the proper wires on the vehicle. Also i did turned on unlock/lock before and after remote start and driver side will unlock before remote start but will NOT lock after, also have the lock after foot brake and unlock when ignition is shut off programmed but door locks also doesnt respond to it.
and lastly alarm does NOT trigger,im inside vehicle arms vehicle wait a few sec then i manually unlock door and open but the alarm does NOT trigger,the only time it works is when i press the panic button.
when unlocking the doors with the factory keys i have to hit unlock button twice for all doors to unlock.not sure how that will work with rf kit remote.
also on wirecolor.com i notice theres wires for door pin FL(orange) and door pin FR(blue) on the vehicle, but i don't know which wires will i connect from the evo module to those wires if is needed.

please get back to me asap
thank you very much

2016 Scion IA Trunk button not working with revo4.1 remote and evo one

Fri, 27 Jan 2017 11:24:25 +0000

The trunk release button on the Revo4.1 remote does not work at all with the car running or not.

The doors lock and unlock and remote starting is working using the revo remote.

A2 trunk release and A10 Trunk trigger options are on.

Is there some setting or connection that I may be missing?

USDM 2013xB Canbus Door lock control?

Fri, 30 Dec 2016 00:22:23 +0000

I recently got my evo one today, and installed it after some back and forth with the firmware and the updates. It starts using the lock-unlock-lock feature (did this so that the alarm is in a disarmed state when the engine starts, so no need to splice into key sense) However, when I start the car using the remote, nothing happens when i go to try and unlock the doors using the remote. I know that the car ignores the remote with the engine started, and I can see that the evo one is recieving the lock and unlock commands from the vehicle(can see blue light blinking with each key press ) but I'm unsure if the doors are supposed to unlock with from the can hi and can lo connections, or do i have to splice into the door lock and unlock wires in order for the door to unlock?

2013 USDM Scion xB no immobilizer EVO-ONE install.

Thu, 22 Dec 2016 23:23:27 +0000

Can someone point me in the right direction as to what wires I need to tap into for EVO-ONE to work with my USDM 2013 scion xb?.

I have 2 different wiring diagrams( 19281 and 58481) , that both say almost the same things, but i can't trust them 100% yet.

I purchased wirecolor passes for both the 2008-2010 model years, and the 2011-2015 model years, and they are the same car, and none of the pictures show the 7 pin connector that I have to tap into for TX (transmit) and RX(recieve) data.

My question is what kind of data is being sent over these tx and rx lines? Is it RKE transmit and recieve, CANBUS transmit and recieve, or something completely different?

I want to make sure the doors will still unlock when the engine is running, and i want to make sure that if these are the only data connections that are being made to the car, that it will do everything that i want it to do, which is lock and unlock the car with the engine remote started. for reference, I plan to use the TOY1 T harness for my install, if applicable

EDIT: also, i have the RS3200 security system, does this affect anything? From what i see, i think i would have to splice into the key sense wire in order for the alarm to disarm when the engine starts. (you can arm the alarm, then put the key in the ignition, start the car and the alarm doesn't go off)

Evo One it will work for 2014ScionXB? The car has no immobilizer system.

Fri, 09 Dec 2016 17:10:46 +0000

I bought the Evo One and i'm having a problem to get it working. I followed guide# 23001, REV:20160601, wiring done and at programing step 5, when I turn the key towards the "on" position the red LED begins to blink and it does not stop. For I have purchased a used car, and it had come with two keys, with one having a Scion logo on the back and a Toyota logo on the other key. The Scion key does not have any stamp marks, and the Toyota key has a H stamp on it. The vehicle I bought was certified by Toyota. To test if my car has a immobilizer I had cut a new key (no chip) in the local hardware store. The new key started the car, while the original keys were in the house twenty feet away. And I googled that only the Canadian xB needed the bypass module. So the question is whether or not the unit will work for the car and how to wire and program it in said vehicle. The firm-ware was installed at the place that I have purchased the Evo One.

(-)AUTO-LIGHT WIRE

Sun, 04 Dec 2016 10:12:51 +0000

EVO ONE WITH THAR-TOY1 THARNESS

In my 2014 scion xb, plug to light switch at pin 12 do not have wire can I just ignore this connection?

frs oem remote

Tue, 08 Nov 2016 18:21:30 +0000

working on a 2016 scion frs. using evo all with a compustar cm7000. evrything program correctly and works from compustar remote. and I have option C1 on as per the manual but the OEM remote does not activate the compustar alarm, and not sure if supported but 3x lock does not work either.\

edit: put everything together and now it starts but the cars shuts off after a couple seconds. locks still work and tach programs okay.

i also noticed on the installation it says to interupt the security light. there is no wire in that location given in the installation manual

Start but no crank, 4 times parks light on Evo One

Mon, 04 Jan 2016 14:12:03 +0000

Ok so I finally got my Evo One to respond and actually do something but the remote start is not working. I Have a 2015 Scion FRS with PTS on a manual trans and does the same after leaving it in Ready Mode. I have cut the yellow loop to make it think it's an auto for troubleshooting by the way and the clutch is by passed. I have put a multimeter and it looks like it send power from the starter wire but it very short and it appears to happen when the 2nd ign is turned on (white wire), basically clicks on and then off.

The park lights flash 4 times after it fails so based on the guide it indicates no tach signal but I have tried setting 20.2 and 20.5 and 20.1 if I rememeber right.

On a side not my service number is 002b03046373 but 002b02046373 shows my info, am I missing something?

EVO One and FRS issues

Wed, 30 Dec 2015 20:04:22 +0000

In short my goal is to make the lock x3 work for me but the module is not sending any power from the main 6 pin harness as it should.

I have a 2015 Scion FRS with PTS and after a full day I figured out that no matter how many times I try the dcrytor didn't take the immobilizer data as a 2015 FRS. After some self troubleshooting I found out that I can get it to work if I put it down as a 2014 or 2015 Subaru BRZ with PTS. After going through all the steps and putting the EVO One back in the car it turns the yellow LED when in the ignition but does not do anything when trying to use the valet button, no horn no park lights and yes they are wired correctly and check with a multimeter to ensure the module is getting the signals. The blue LED does blink when I press the press the lock and unlock from my factory FOB but more strangely the factory alarm doesn't work anymore, if I click lock button on the FOB and manually open the door the alarm doesn't go off, it does nothing. The car does turn on fine apart of now having the airbag light on. This is driving me crazy and tech support hasn't been able to help much, they say "there's no reason it shouldn't work" I have double and tripled check the wiring and all connections are on the factory wires directly and securely. I can't find any info on this module being used on a BRZ or FRS so I'm starting to question the true compatibility or is there something wrong with this particular module. The AX-One is the same as the EVO One right?

2015 Scion FRS (manual) push to start not programming

Tue, 29 Dec 2015 00:33:21 +0000

I go through all the steps and but but when I connect the EVO ONE the second time to read the sample of the immobilizer I get:

The module was not able to sample the vehicles immobilizer data.

I have tried multiple times and sometimes after I start the car the red light doesn't blink and sometimes the red light blinks while the blue led is steady on then the blue led flashes then the red and yellow alternate. This makes it take longer but I have had it go through the regular steps and still the Dcryptor part is not getting my car's data.

evo one and rf642w scion iq

Sun, 20 Dec 2015 16:19:59 +0000

Bought for remote start and wire up using the manual for "G" key of which is only one. Keys have absolutely no markings on them. Find out car does not have immobilizer. Don't think evo-one is getting programmed as the led's don't do as they should in steps 4 and 5. Could not get programmed for factory remote. Bought the rf642w kit and still no go. Everything is extremely vague about any programming and have tried numerous different ways. Knowing that there is no factory security I'm trying to use system for remote start and alarm functions.

Scion im bypass

Sun, 04 Oct 2015 21:27:29 +0000

Can i use a tbrav4 on the new scion im 2016?????

Is Excalibur RS 260DP compatible with Key-override-all module?

Wed, 28 Jan 2015 19:11:09 +0000

Hi, I just got a Excalibur RS 260 DP and Key-Override-All bypass module to install on 2007 Scion tc but the RS 232 data connection wires between the remote starter and the module does not match, is it posibble to use or do I need to get a different bypass module? Thank you

after setting reservation mode, engine won't shut off after last door closes; compustar 6000as with evo-all, scion frs

Thu, 30 Jan 2014 22:11:26 +0000

I have a 2013 scion frs 6speed, compustar 6000as with evo-all bypass. evo-all is connected to compustar via d2d. after setting reservation mode, the engine stays running but does not shut off when last door shuts. d2d protocol is set as fortin for compustar.

I called tech support and was told evo-all needs a protocol turn on for scion frs. and so i order an flash link updater. what protocol or options needs to be turn on for the scion frs with compustar using evo-all bypass?

2013 scion xb

Fri, 13 Dec 2013 11:58:54 +0000

works for 3 days then kick evoall out of programming