Questions & Answers - Recent questions tagged 2017

2017 Renegade

Fri, 12 Jun 2026 21:22:01 +0000

Hello. When I'm programming the Evo-All on a 2017 Jeep Renegade, the blue LED starts blinking after 5 seconds (after pressing the button), and after turning off the ignition, the red LED stays on continuously. I've already tried it on two modules.

2017 IS-300

Mon, 25 May 2026 14:08:46 +0000

Hello. I installed a remote starter on a 2017 IS-300. I reprogrammed the firmware three times, but it didn't help. It programmed successfully, but when I pressed the button on the factory remote, the blue LED didn't respond (001A07213969). After that, I installed a different module, and it worked. What could be the cause?

Volkswagen Golf 2017 Push-to-Start -Digital Dash

Wed, 12 Nov 2025 18:29:19 +0000

I have the EVO-VWT1 system installed in my VW Golf no key sacrifice. I am wanting to upgrade the dash from analog to digital. What changes if any do I need to make to my current system to keep the same functionality

EVO-ALL, 2017 Infiniti Q70, unable to get past step 7 (standalone with T-harness)

Tue, 25 Feb 2025 19:24:07 +0000

On step 7, brake pedal press turns on blue and red led, shortly after, red led does not stay on and turns off, only blue led stays on, unable to continue on to step 8.

S/N: 001A07 670775

2017 Impreza orbit one Evo-All came in car used

Thu, 20 Feb 2025 12:46:18 +0000

Bought a used car with “Orbit One remote starter & alarm & bypass module”

Starter Vr: 7.1.21 , Evo-All Vr: 4.18

Serice No: 002B07 323505

Was bought without a remote start key, wondering if I am able to program a new key, or remove the entire system and have done by dealer

2017 Forester can't program DCryptor

Sat, 25 Jan 2025 19:57:57 +0000

2017 Forester X, key start, new EVO-One, installed per Guide #97491w/THAR-ONE-SUB1 t-harness, all connections made per pin location, not wire color. When I reach Step 5 on the DCryptor programming and start the car, I get red/blue on solid and they stay on even after the car is shut off, until I pull the 6-pin. Car starts normally with the key if the EVO-One is connected, will not start with the red plug disconnected, which I believe is correct. I've reset and reprogrammed the module twice with the same result.

Update after reading multiple other recommendations about getting to solid red and blue at step 5: 1. Instructions say to use Firmware 84.11 (minimum), I have 84.12 and .11 is not available. 2. I checked continuity from pin 10 (light blue) of the 20 pin connector (IMO signal) to pin D1 (Yellow/green) IMO body side and have continuity. Car starts and immediately quits with red "D" connector unplugged, starts and runs normally with it plugged in. 3. Have battery voltage at E1 (white) and E5 (pink) with ignition on, no power with ignition off. Module SN:002B04 656833.

What’s needed? 2017 Audi S3 PP DSG Virtual cockpit

Thu, 09 Jan 2025 14:08:24 +0000

As title states what do I need to order to install remote start capabilities. Which system EvoRS, Evo One, T-harness AUD1 or 2, bypass modules, etc.

Thanks in advance!

2017 Tuscon push start issues

Mon, 06 Jan 2025 09:33:12 +0000

Installed evo one with t-harness, tried to program and unit doesn't seem to work. No to start or stop the engine,

I need to press start/stop two times? Any suggestions or help would be appreciated. without hood pin, A11 should be on or off? Only wire that i had to splice was the lift gate wire...

2017 Fusion

Mon, 30 Dec 2024 13:41:41 +0000

Hello. I installed evo-all (001A07356265) on 2017 fusion. Doesn't start and blinks turn signals 2 times.

2017 F350 Super Duty Evo all 1 key programmed successfully but won't remote start

Wed, 13 Nov 2024 14:41:53 +0000

Upon trying to remote start the red and yellow come on and blue blinks 1 time but not start. Stick key and turn forward, yellow light comes on. What am I missing?

2017 LS460

Sat, 09 Nov 2024 11:39:27 +0000

Hello. 2017 LS460 not on the list?

2017 S3 - First Time Installer/User want to make sure I have the correct parts!

Thu, 02 Nov 2023 13:07:26 +0000

Hey everyone! First time user/installer here and I am doing a mini project to install the remote starter on my own. I was originally quoted over $600 to do an install and after some research, I've found that it's a relatively easy DIY install. Given it's my first time, I'd like to make sure I've got all the parts needed to get it working the way I want.

My car:
2017 Audi S3 Prestige (Push to Start) - Initial Delivery date of Feb 2017 (in case manufacture date matters)

How I'd like it to work:
Simple ~50 feet (~20 meters) distance to remote start using 3 presses of the lock button with the OEM Remote.
I do not want to install a spare-key in my vehicle or sacrifice one of the key fobs
I'd like both key fobs to be able to remote-start the car
I'd like the car to run for 15-20 minutes before turning off

To do the install, I've purchased two items so far:
Fortin EVO-ONE From Amazon [OR Fortin VW-T1 (from Walmart, sold w/ THAR)]
Fortin FLU-100.2 From Amazon (Crimestopper)
Fortin THAR-VW1

Questions:
I read in the installation instructions that the Key Bypass - TB-VW Module is not supported with the Virtual cockpit (or virtual cluster). Are there any workarounds?
Are there are special parts that I require?
Are there any concerns with respect to my battery? (I already have a dash cam & radar detector installed directly to the fuse box)
Are there different versions for American or Canadian cars?

Thanks so much!

2017 SQ5 Evo-All do not run

Tue, 10 Oct 2023 19:27:31 +0000

Hi,

I have install Fortin Evo-audt1 on my audi sq5 2017 but doesn't work. I have connect foot brake wire, Can H & Can L under steering column also I tried under hood clutch and harness on key port. I did the program but on the 8th step doesn't flash red and yellow light, only 3x red light. I try to remote start but nothing happen. if i put the key on key port the remote starter works. SN 001A07 481140. VIN:WA1CCAFP3HA009841.

Can you help what can I do?

LC200 EURO

Fri, 07 Jul 2023 07:39:24 +0000

I install fortin evo-all on LC200 (EURO) (standalone--408261). I release the programming button to blue. I connect the rest of the connectors. I turn on the ignition, the blue goes out and after a while the red starts flashing. Wire colors don't match either.

2017 Ford Focus Parking Light Diodes

Thu, 08 Jun 2023 19:47:03 +0000

Guide 72871. 2x 3 Amp Diodes and for L/R parking lights and 10 amp fuse behind glove box. I see these are optional, but what are their intended uses? or recommend use for?

2017 CX-5 Doesn't Get Yellow Light When Ignition Turned On

Sat, 18 Feb 2023 17:03:47 +0000

Installing Evo-All & THAR-MAZ1 on 2017 Mazda CX-5.

Followed the guide (62391/66311... different guides if going through troubleshooter vs Flash Link guide) for firmware & options (tried firmware 85.12 & 85.11)

THAR-MAZ1 only has Start/Stop 2nd connector (24 pin) & no 32 pin connector. So I am using the recommended wiring connections minus Data Key & Door Lock Data (A10 & A20)

When programming I cannot get the module to recognize a key (blue LED, no yellow LED illuminated when ignition is turned on).

Is the Data Key (A10) required? It is not in the THAR-MAZ1 harness nor is it populated in the OEM female connector.

One of the keys to this vehicle was lost previously & only have 1. Is it possible to program with only one key? (the Flash Link Manager notes that 2 keys are required. I don't quite understand why)

Evo one won’t remote start but will let the car continue to run after starting the car manually..

Wed, 25 Jan 2023 20:30:47 +0000

2017 Subaru WRX. Won't Remote start. Manual Trans. The yellow wire on the main harness (T-Harness) that goes to the clutch wire does nothing when trying to remote start. But the car will continue to run after I turn the key off.

Hood pin wire 2017 Toyota RAV4 Hybrid

Mon, 23 Jan 2023 11:49:24 +0000

Where would I need to tap the pink/black wire from the Evo one for the hood pin switch on the interior? I believe it's on the body control module but I'm not sure which connector or wire. I would rather use the factory hood switch if possible rather than installing the aftermarket one and not have to run a wire through the firewall. Thanks

17 Tiguan PTS no dcryptor option in flashlink programmer

Sat, 31 Dec 2022 11:49:11 +0000

Trying to get everything prepped before install, have evo-vwt1 with tb-vw and when trying to program the module, it auto-fills the "installation method" step with "key in a box" and says 1 sacrificed key no decryptor. I want to use the decryptor, but theres no combination of settings that enables it as an option. running newest software and firmware, do i need to start the install and try to pull key data first? i didnt want to continue because i wont use this kit if i need to burn a key for it to work

Lexus ES300h 2017 lights flash 4x and doesn't start

Fri, 30 Dec 2022 14:26:05 +0000

Using evo all and rfk942 on 2017 lexus es300h. hybrid, pts.
Installed using harness and connected white/black to purple wire on start/stop switch.

Programmed without issues, dcryptor ran fine. Able to lock/unlock using both OEM remote and rk942 remotes.
When trying to start (with either the oem or rk942) the parking lights and the red led on the evo all flash 4x.

Have tried:
a11 hood switch off, reset and reflashing, tested all connections. confirmed D4, D6 enabled.

Instructions say this means ignition before start. Not sure what is meant by this. The French translates to ignition key detected before starting? I have placed both OEM keys at a distance and tried the rk942 to start and got the same result.

2017 toyota LC200 Repetition of the question.

Tue, 13 Dec 2022 22:29:05 +0000

I installed an Evo-All and a remote start alarm on a Toyota LC 200 (2017). Remote start sets the car to factory alarm and if I open the door with the alarm installed, the factory alarm goes off. The doors are closed with a purple wire and it will arm, but when I open it with a purple-white wire, the standard(factory) alarm goes off (an alarm is triggered). evo-all 001A07312787

2017 toyota lc 200

Sun, 11 Dec 2022 03:49:30 +0000

Module wont connect in FlashLink manager

Sun, 06 Nov 2022 14:04:21 +0000

When i connect my FlashLink Lite into the USB port it connects and LED becomes solid red. So that is working. When connectin the 4pin to the EVO-ALL module it is saying in FlashLink manager that the module is not connected. However, the module is slow blinking blue so it atleast has power to the unit. Im running windows 10. And i already tried reinstalling bot the manager software and the driver software.

2017 EvoOne with TharFor3 T harness, blue light won't blink on programming

Thu, 25 Aug 2022 15:33:16 +0000

Thank you in advance for any help! I am a long time using of the EVO ALL and have done a few EVO ONE. A bit stumped on my 2017 F150 though. Using EVO ONE with the THAR FOR 3 harness.

All plugged in. Following wiring diagram for the A1 and A16 (put them together) on the white 20 pin connector.

When I go to program it, I can't get it to "blink blue". Therefore, I can't get any further in the programming procedure.

Followed the directions in the Guide. What could I be missing?

Joe

MyCar and Fortin EVO-ONE with T-Harness setup on Subaru Outback 2017 Standard Key not working

Fri, 03 Jun 2022 16:30:15 +0000

I'm trying to add MyCar to a Fortin EVO-ONE installation on a Subaru Outback 2017.

The Fortin EVO-ONE works fine - I can start the car using the OEM Standard KEY/Remote without any issues.

I followed the steps provided in the install guide to add the MyCar

Protocol is set up to Fortin2 using the FlashLink MAnager on EVO-One for RFKit

Setup as Fortin in the MyCar application Settings.

I did the following steps to learn the MyCar into Fortin EVO-One

1- Cycle the ignition to the ON position.

2 - The YELLOW LED on top of the EVO-ONE should come ON.

3 - Press and Hold the EVO-ONE push button for 5 seconds.

4 - The parking lights and the RED LED on the side of the EVO-ONE will turn ON.

5 - Release the push button.

6 - Press and Release the push button 5x times. Everytime the push button is pressed the parking lights and the RED Led on the side of the EVO-ONE will blink.

7 - Then Press and Release the Brake pedal.

8 - Seconds later the RED LED on the side of the EVO-ONE will blink once to confirm that the MyCar ID has been learned to the EVO-ONE.

9 - Cycle the vehicle’s ignition to the OFF position to Exit the EVO-ONE programming

All steps succesful.

In the MyCar app I can see the voltage of the car and the GPS location, however the START/STOP/LOCK/UNLOCK functions are not working from the MyCar application

Any ideas/help?

Thanks

'17 Camry H Key - Remote Unlock not working while engine running

Mon, 21 Feb 2022 03:53:14 +0000

I installed the Evo One Kit with the TOY-4 harness on an H key '17 Camry today and mostly everything seems to be working. I'm using the OEM remote. The only issue is after I triple press the lock key to start the vehicle, I can't use the remote to unlock the doors. I thought everything was programmed properly but apparently not. How should I resolve this issue?

Autolights, foglights and high beams stopped working after installing EVO-RS TOY6 on 2017 Lexus NX200t

Sun, 20 Feb 2022 20:32:47 +0000

Just installed EVO-RS TOYT6 (EVO-ALL + TOY6) on 2017 Lexus NX200t for OEM remote start (3xLock) and works fine. The only issue is that autolights do not work (lights do not turn on even if it's dark outside) and foglights do not work, either.

EDIT: Also noticed high beams won't turn on, either. The "symbol" indicator shows up on the dash but the physical beam lights do not turn on.

Anybody has a fix for this?

No remote start on 2017 Toyota rav4 push to start

Sun, 30 Jan 2022 23:21:24 +0000

I recently installed the evo all on my 2017 rav4 push to start using the evo all and thar toy6 t harness. The module took programming but i have no remote start. The module is attempting to start but no dash lights or remote start. Followed the instructions for t harness install and programming and no luck. Also used connector A which was labeled from factory.

Can't get into the car after remote-start

Sat, 04 Dec 2021 08:05:57 +0000

Hello, I purchased a second-hand Subaru WRX STi 2017 (manual, normal key) with Fortin Evo-one(?) installed and FTXDUO remote control. Remote start works ok (thank you for that - a great product!). The only problem is that after remote start I can not get into the car - buttons of original key do not work. If I press Unlock button on FTX, the car unlocks and then locks up immediately. I have to remote-stop the engine, only then I can use original key to unlock the door and get into the car. Something must be missing here, but what? Or am I doing something incorrectly?

2017 jeep compass

Mon, 15 Nov 2021 10:16:43 +0000

Hello. In the manual № 98391, in the programming procedure, in the 7th step, it is written that press the start-stop to turn ON the ignition. Then it is written again, press the start-stop to turn ON the ignition ... And when did we turn it off?

2017 audi s3

Thu, 04 Nov 2021 03:57:41 +0000

I have a 2017 audi s3 pts with the virtual display. I read somewhere that the evo all does not support the virtual display. I am wondering if the evo one does, and if im wrong does the evo all work as a standalone starter or will a third party starter be needed. Also would i be required to sacrifice a key for the remote start.

2017 hilux

Thu, 28 Oct 2021 10:03:09 +0000

Hello. Today I installed evo-all on a 2017 Toyota HILUX. The module has been programmed, but the car does not start remotely and the dashboard writes "malfunction of the entry and start system." What should I do? 001Ф07 032826

2017 Ford Ranger Australia

Sun, 25 Apr 2021 02:27:23 +0000

Hi, can anybody kindly inform me if the EVO-All kit works with Australian 2017 Ford Ranger XLT? I have the following equipment EVO-FORT3 and the flash-link updater but cannot find guides for 2017 ranger. Many thanks in advance

How to reflash fortin one

Fri, 23 Apr 2021 12:31:51 +0000

Remote start is not working after update to 1.25

THAR-ONE-SUB2 & EVO ONE on 2020 Subaru WRX PTS

Sun, 14 Mar 2021 00:31:28 +0000

I have installed the THAR-ONE-SUB2 in my US WRX per the instruction guide, page page 7/11 T-Harness - Automatic & Manual Transmission
https://cdn02.fortin.ca/download/98951/evo-one_ig_rto_bi_sub2_wrx_2019_pts_b_98951.pdf

ASK:
1.) Why is the car not starting with the Yellow/Red and Yellow/Green separeted per the installation guide
2.) Does my US WRX have to follow the Canadian Vehicle steps, if yes why and if no what is the difference

Installation was simple as mainly 2 connectors and areplug N play. I master reset my Evo One, flashed the 2020 WRX firmware and follow the programming steps on page 8/11. When I get to step 5 to start the car, the car starts and shuts off immidiately, eventually not even turning the starter. The lights on the Evo One stay solid for Red and Blue and programming does not complete to follow up on the Dcryptor part. After a little troubleshooting I found that I can get the car to start if I reconnect the Yellow/Red and Yellow/Green wires I cut eariler making the car at least drivable again.

looking for a no key required for Audi A4 and Q7 2017-2020 solution using thar-aud2

Wed, 06 Jan 2021 09:09:11 +0000

i am looking for a bypass soloution for 2017-2020 Audi A4 and Q7 models that do not require a sacrifice key. also want to be able to use t harness to avoid splicing the wiring in the vehicle. the customer only has one operational key for the vheicle.

Where to connect the Yellow wire on the Evo start 2. Using EVO one and THAR TOY 8

Wed, 30 Dec 2020 18:55:36 +0000

Using the THAR TOY 8 and EVO ONE, wanted some clarification on where to connect the yellow wire from the EVO Start 2.

elantra 2017 (automatique)

Thu, 10 Dec 2020 19:19:24 +0000

elantra 2017 automatique fonctionait tres bien et tout dun coup ne fonctionne plus l ignition se fait mais le demmareur ne crank plus et 3x flash mode pret a demmarer desactiver embarque

2017 LX570

Thu, 15 Oct 2020 13:28:54 +0000

i have 2017 LX570 with factory remote start but the car turns off when i unlock the door which product i can use to keep the car running when opening the door and drive

2017 Cadillac Escalade Take over can be accomplished without key

Sat, 08 Aug 2020 00:22:35 +0000

i recently installed evo-all stand alone with T-harness Thar-GM6 and ASCL6 Every thing seems to program normally with out any problem but when i go back and check functionality i find severals problems

#1. Car can still be driven away if i dont have my keys on me. (Unlock with phone --> open door --> press brake --> put car in gear --> drive away)

here is a problem when i try to shut off the engine and press push-to-start button it shuts the engine but it stays in accesory mode and keeps telling me it could not find key and tells me to press brake and push push-to-start button to restart engine. To my surpise it starts without key again ( i have to press two times to shut it off) other wise accesory will still be on even if i get out of the car and lock some body can get in and start without keys (not to mention it will drain the batterty

#2. When i try to open trunk with one button it opens glass and trunk lid at the same time i can't seem to separate those two commands

question #1 isn't it suppouse to shuts off without key (sercurity/safety reason)??

#2 did i miss something?

#3 what can be done to separate opening glass from trunk lid (put them on two separate Aux channel)

may be i need to cut and reconnect C5 (brown wire) to Grey 26-Pin plug pin 23 (green wire) because its connected to 27-Pin Blue Connector pin 22 ?

Accessories or radio does not turn on with remote start- fortin evo one t-harness

Sun, 07 Jun 2020 18:14:59 +0000

My accessories i.e. radio, usb plug in do not turn on with remote start. I sit in with and turn key in ACC, radio and accessories turn on. Once I turn the key in IGN, SRS airbag light stays on. I believe once accessories and radio are able to turn on with remote start, SRS airbag light issue will resolve. I have the T-harness, mycar and long range remote as well. How do i wire this up so accessories, radio and even A/C turn on with remote start?

Attempting to add rf912 to evo one

Tue, 02 Jun 2020 23:22:18 +0000

I have an evo one with a T harness installed in my 2017 jetta (standard key) and have been using the manufacturers key fob to start my car for about a year now. Wanting to upgrade the range, I purchased an evo rfk 912 2-way rf kit to add to my evo one. Unfortunetly I am having issues installing it. I have tried following the instructions that came with the remote, I have tried to find other installation guides on the fortin website, and I have tried to see if there are any YouTube tutorials that could help.

Things I have tried:

- Plugging the antenna in to port B on the EVO ONE

Standard reprogram of evo one (hold button, release on blue light , ect...)
Stoping on blue and red light (saw it in a youtube vid)
Looking on Flashlink manager for settings
all instructions that came with the remote

- Plugging the antenna in to the T-Harness

All of the same as above

I am yet to even get the led on the antenna to light up. Please help.

Thanks

THE DIFFERENCE BETWEEN: VW JETTA - PUSH-TO-START (2017-2018) vs PUSH-TO-START MFD-UP-TO-08-2018 (2019)

Sun, 02 Feb 2020 11:54:15 +0000

I have a 2017 VW Jetta Push button start so I bought a subscription to the VW JETTA - PUSH TO START (2017-2018) photos and guides. However, I just found photos and guides for VW JETTA - PUSH TO START MFD UP TO 08-2018 (2019). What is the difference between these two? Should I purchase the photos and guides to VW JETTA - PUSH TO START MFD UP TO 08-2018 (2019) as well?

Please help!

2017 Chevy Express T harness

Sat, 01 Feb 2020 18:30:44 +0000

I'm tryin to install the EVO-GMT4 kit in my work van but it seems that the T harness doesn't fit in the ignition connector. Is it possible that the late model 2017 chevy Express vans changed their ignition connector? If so how can I make this work when I looked it up and it said it was compatable?

2017 Highlander It Locks/Unlocks but DIDNT remotely start from Mobile.

Sun, 26 Jan 2020 08:48:22 +0000

2017 Highlander Push to start EVO All standalone with Tharness & Evo start2 It Locks/Unlocks but DIDNT remotely start from Mobile.

I had evoall standalone with Tharness installed on the 2017 Toyota Highlander push to start working perfectly fine

Purchased a evo start2 with flash Link Updator 4

Removed the evo all module and update the firmare to latest

Save receommended options and save the options

Checked the Option C1,D1 H & H2 are on on the module

Try to decrypt thru decryptor, didnt succed

Installed EVostart 2 Antenna in the car windshield

NOTE: the antenna cable shown in installation guide is bit different from shown, have more connector and loose 4 cables red black yellow and green

Using Connection1 from evostart2 guide for EVO ALl standalone Installation

StepA:Connect 6 pin Antenna conector to Antenna

Step B: Connect 4 pin female blue connector to 4 pin male black connector from T harness

STep C: Connect Yellow wire from Antenna cable to Yellow wire going on A1 on 20pin white connector of T harness

Program EVO All with EVO start2 and got a green light. (programming successful)

Installed app on mobile and try to start,

When trying to start from MObile, the evostart2 gets a signal, shows blue light in atenna , but do nothing

I tried with OEM key fob for lock x3, it does nothing

Factory Reset the module, flash the module using flash Link Updator 4

Turn on c1 d1 and d6 h2

Program the module again and works with oem remote

Program the evo start2

Able to lock and Unlock, but not able to start from mobile

Troubleshooting:

I removed the yellow wire sttached to tharness

DONT KNOW WHAT HAPPENS WRONG

ALso checked grounding dark blue wire from 20 pin T harness to check if get red, NO D1 is enabled

please help

"Take Over" feature available on 2017 Honda civic with Evo all ?

Wed, 01 Jan 2020 22:04:09 +0000

Hi there,

I am trying to install remote start with Evo all on 2017 honda civic, and I wanted to know if it supports "Take Over" feature or it will kill the engine when the door open or brake pushed ?

Thanks

What is the blue 4-pin male connector for on the THAR-FOR3 harness?

Sun, 13 Oct 2019 13:21:39 +0000

My car is a 2017 Ford Fusion push-to-start. I have a Fortin EVO-ALL to install with the THAR-FOR3 harness and then plan to hook up a MyCar smartphone controller which has a blue 4-pin female with the same colour wires (red, black, blue, white) as the T harness blue connector. Can I hook up the MyCar controller to the blue connector on the T-harness? Just wondering because the MyCar wiring diagram says to use the HRN-LLRS-01 cable which has the same colour wires. I will be using my OEM fobs for remote start (lock 3x). Also, do I need to use the 20 pin white and the 6 pin red connectors? I have no idea where those wires would connect to!

I want to turn on alarm and add shock sensor and siren

Mon, 23 Sep 2019 18:22:38 +0000

I would like to add a shock sensor and siren to my Evo All. What do I need to make this happen? I know I have to go in and turn on the settings and I have the flash link.

Can I use LINKR LT2 with EVO-NIST4

Mon, 09 Sep 2019 12:12:14 +0000

I ordred an EVO-NIST4 with flash link. It says it is compatible with most telematic & GPS modules including Smart Phone and compatiable with Long Range Kits. Will the LINKR LT2 work with this particular unit?

can i add Rf range extnder and Lnkr Lt2 bluetooth to the Evo All and if so what HArness do I use to connect it?

Mon, 09 Sep 2019 11:17:12 +0000

Can I hook up RF extender and LINKR LT2 on the EVO All. So for example, if i dont want to use remote i can use my phone and vise versa. if i dont want to use my phone i can use rf remote that is provided with crimestopper rf extender kit. thank you