Questions & Answers - Recent questions tagged 3x-lock-start

Q50 not remote starting

Mon, 06 Jul 2026 04:12:34 +0000

i have a 2015 infiniti Q50

SN-002B04 759527

i installed the evo-one with thar-nis4 t harness and RF942 kit.

programmed, decrypted and reinstalled tested with oem keyfob worked great, than i programmed the 2 RF remotes, test again worked good 3 times then just stopped working. i can still unlock/lock with all 3 fobs. it will try to remote start, gets to where it should crank and nothing.

2017 Renegade

Fri, 12 Jun 2026 21:22:01 +0000

Hello. When I'm programming the Evo-All on a 2017 Jeep Renegade, the blue LED starts blinking after 5 seconds (after pressing the button), and after turning off the ignition, the red LED stays on continuously. I've already tried it on two modules.

2017 IS-300

Mon, 25 May 2026 14:08:46 +0000

Hello. I installed a remote starter on a 2017 IS-300. I reprogrammed the firmware three times, but it didn't help. It programmed successfully, but when I pressed the button on the factory remote, the blue LED didn't respond (001A07213969). After that, I installed a different module, and it worked. What could be the cause?

Alarm goes off whenever I open the door after using remote start.

Thu, 23 Apr 2026 00:16:43 +0000

I can remote start it perfectly fine but as soon as an open a door the alarm goes off no matter if the I spam the unlock button before opening.

2005-2010 Toyota Tacoma remote start using factory remote

Thu, 12 Feb 2026 21:25:46 +0000

Following on a question from Sep 13, 2019: Toyota Tacoma Evo one installed but will not start or blink after being programmed.

Fortin Support stated that the factory remote can be used to start the engine by pressing the lock button three times when the driver's door lock signal (ground signal with a relay) is connected to the center pin of the shock sensor using remote start firmware 0.82.

Does this still work? Is there a firmware version avaliable that can do this?

2024 CHR

Tue, 10 Feb 2026 18:18:11 +0000

I installed a 3xlock remote engine start on a 2024 CHR. Everything was the same as on a 2024 Prius Prime...only some of the wire colors were different.

2016 KIA K7

Tue, 20 Jan 2026 11:53:26 +0000

Hello. I installed Evo-One on 2016 Kia K7 (on liquid gas...with start-stop).. I specified 2017 Kia Optima in the manager. The EMS wire was behind the passenger kick panel in the red connector on the bottom, second from the right. Behind the fuse, the ignition wire (ON) was pink...the ACC wire was white...the starter wire was yellow with a black stripe. The CAN wires were also located behind the fuses in a small connector... yellow and black... blue and orange. Everything worked well, but after opening the door, when I pressed the brake, the car stopped... When I pressed the start-stop button, the radio turned on, and the start-stop button also showed a yellow LED, but the car stopped when I pressed the brake.

I didn't use the ACC-2. It was blue, behind the fuses. The customer left satisfied, but I'm wondering what else can be added to prevent the car from stalling when the brake is applied?

If you could please send me the serial number of this Evo-One...I usually write down the numbers in a journal and now I forgot to write them down...

Kia K7 Cadenza

Mon, 19 Jan 2026 15:17:41 +0000

Hello. Does the remote start with three locks (38.2) work on 2015 Cadenza? ( with Evo-One)...I want to install it on K7

2024 L200 remote start

Fri, 02 Jan 2026 16:06:55 +0000

For Information ...I installed Evo-ALL (3x-lock) on a 2024 Mitsubishi L200 (diesel). I specified a 2024 Outlander in the manager. The start runtime was 10 minutes (like on the Outlander), but the number of remote starts after parking the car turned out to be 2 (the Outlander manual says 1). I connected CAN-H and CAN-L in the BCM, on the middle gray connector, on the pink and purple wires.

kia soul 3x lock

Sun, 28 Dec 2025 18:47:05 +0000

allo

sur kia soul 2016 on dirait que module evo one en 3x lock ne fonctionne pas ??????

2013 Passat

Wed, 24 Dec 2025 17:19:07 +0000

Hello. I installed an Evo-ALL with a TB-VW bypass module on a 2013 Passat(key). In cold morning, the car started having trouble starting, even with the key. Everything worked fine during the day, but on a cold morning, problems developed. Immobilizer error. The customer demanded a refund, so I removed everything and refunded him. It would have been better to have a chip (a clone key, right?), but I still have a few of those bypass modules left.

2017 qx70 push the remote 3x and module clicks but dosent start

Mon, 22 Dec 2025 17:45:39 +0000

Light first red then red blue then red then yellow red then red blue then red then red yellow then red with 3 clicks

toyota land crusier 2010

Tue, 25 Nov 2025 10:29:36 +0000

hello plaese can you help i fix evo all for toyota land crusier 2010 all good and working fine

but when i press lock 3 times the car is starting but the starter stell in on position for 2 second

i mean the starter timer its longer to start the car any soultion for this

Volkswagen Golf 2017 Push-to-Start -Digital Dash

Wed, 12 Nov 2025 18:29:19 +0000

I have the EVO-VWT1 system installed in my VW Golf no key sacrifice. I am wanting to upgrade the dash from analog to digital. What changes if any do I need to make to my current system to keep the same functionality

Evo One randomly stopped starting the vehicle and I don't know why

Mon, 10 Nov 2025 14:47:48 +0000

I have been using my Evo One in my Mitsubishi Outland push-to-start for almost 2 years with no problems. Now, the last couple of weeks, it won't start the car. I click the OEM fob lock 3 times, the outside lights all light up like it is going to start. Even the dashboard lights all light up like it is going to start and the radio comes up, but nothing. After a few seconds everything goes back to being dark. I can still jump in the car and start it manually just fine. Any thoughts on where to start troubleshooting this?

What is the complete list of parts needed to install a remote engine start?

Thu, 23 Oct 2025 16:22:42 +0000

Hello

Please write a complete list of what is needed for self-connection, programming and setting up remote engine start from OEM key fob using Evo-All VWT1 unit on AUDI S3 8V 2015 with start button?

I can't understand whether I need only R-link or only TB-VW or do I need both of these units, and what is needed to program the immobilizer bypass so as not to leave the key in the car?

And do I need a transponder?

So that I can order everything at once and not have to order the missing parts to Ukraine again and only then figure out how to install it using the instructions :)

Що потрібно для встановлення Evo-All vwt1?

Tue, 21 Oct 2025 12:59:40 +0000

Hello, tell me, do I need any of these products R-LINK, FLASHLINK MOBILE, FLASHLINK UPDATER, TB-VW to install Evo-All vwt1 on Audi S3 8V 2015 so that remote engine start from the native key works? Do I need to flash the already installed Evo-All unit, or can I just buy the Fortin Evo-All VWT1 unit, install it on the car and everything will work right away? Please tell me what is needed to install remote engine start from the native key so that I can buy it all right away? because I will have friends who will send orders to Ukraine :)

GMC TERRAIN 2019

Mon, 23 Jun 2025 09:01:59 +0000

HI plaese any help i fix evo all with gmt6 harnes for gmc terrain 2019 i have 2 keys oem already only 1 key its working for remote starting but the second key its working fine on the car but the starting remote not working any solution to make both keys working thanks for all

evo all remote start on 2017 toyota corolla does not start the car

Thu, 19 Jun 2025 00:08:24 +0000

programmed the unit, hood pin not installed, A 11 switched to off, hit lock switch 3x car does not turn on, blue led flashes 3x, red led turns on then off, then flashes 3x, no start, no lights. Do I need to have the hood pin installed?

Spark 2017 key

Sat, 31 May 2025 22:27:40 +0000

I have a 2017 Spark key.

I connected the Wire to Wire as per the instructions.

https://cdn02.fortin.ca/download/90461/EVO-ALL_IG_SAL_BI_CHEVROLET-SPARK_2016-2019_A_90461.pdf

When I press the key 3 times lock the switch will open but don't start and the light flashed 3 times red.

When running the engine and shutdown by using the key and pull out then i press the lock 3 times the vehicle runing! and i can put the key in and drive, but if I press the brake the engine stop and I cannot start again from the remote (If i try the switch will open but will not try to start) I must use the key again to start and stop the engine and pull out to I can start again by using the lock button with someone below firmware version!.

Sometimes the engine starts and stop immediately.

I tried firmware version 70.46 & 70.41 & 70.42 & 70.43 & 70.44

I want to reset both units

SN: 001A07157086

SN: 001A07501809

lexus es350 2007

Tue, 06 May 2025 04:24:47 +0000

HI PLAESE I FIT MY EVO ALL FOR LEXUS ES350 2007 WHEN I PRESS LOCK 3* TIMES THE CAR WILL START NORMAL BUT WHEN I OPEN THE DOOR THE CAR WILL SHUTDOWN DIRECT, IS THERE ANY SOLUTION TO MAKE THE CAR RUNNING WITHOUT SWITCH OFF IF I OPEN THE DOOR

EvoOne 3x lock stopped working

Mon, 28 Apr 2025 20:10:52 +0000

When I installed in evoone in 17 Sorento 3x lock no transponder. Programmed fine worked about 10 times in a row. I noticed the doors weren’t locking so I changed setting to unlock b4 lock after reinstalled and tried won’t 3x lock anymore. Noticed the pass door was open that’s why wasn’t locking so swapped that option back off and tried again but still no start. I did hard reset and re programmed it did that just fine tried to start again and still no 3x lock activation. I literally changed 1 option and it stopped working. I changed cars on the Evo saved then went back and reinstalled the Kia firmware and only the options that and outlined in guide which are c1 and 38/2 and I shut hood switch a11 to off. Should b firing up with no issues but it just won’t. Oem monitoring is on the Evo light flashes blue when lock is pressed. I get no shutdown codes

Can I use the A14 switch option for the parking light control when configuring the EVO-All?

Mon, 03 Mar 2025 18:33:49 +0000

Guide says for parking light control the A14 brown/white wire needs to be tied into the light blue wire of the second BCM connector pin 8. Didn't know if the A14 was turned on when configuring the module that would negate needing to tie into the pin 8 second connector on the BCM.

2022 Hyundai Accent - Std-Key-without-Keyless

Sun, 05 Jan 2025 20:27:35 +0000

I have a 2022 Hyundai Accent and two options appear. I don't know what they mean.

Std-Key-without-Keyless
Std-Key-with-Keyless

reciving key signals. not cranking or starting

Tue, 24 Dec 2024 01:03:43 +0000

Im using evo all module with fort 3 T harness. ford ecosport 2019 push start

SN: 001A07 579754

Guide : 80381

I think I did wiring correctly according to the digram. when pressing 3x locks on OEM key LED lights going red yellow blue and blink hazard light 3 Tims and honk. this continues for two times. after that 3x red blinks. vehicle not starting or cranking. I can't find any solution for that on troubleshooting guid. Please help to figure out what is wrong.

not starting when pressing keys 3x

Mon, 23 Dec 2024 22:08:49 +0000

ford ecosport 2019 push stsrt

I think I did all things correct. after pressing lock 3x, led lights going red yellow blue signal and honk, again red yellow blue signal and honk. but vehicle not starting. please help me to find the solution.

Vehicles not remote starting

Fri, 13 Dec 2024 23:27:11 +0000

So i sussfully connected the evo all to my vw jetta 2012. When I press the unlock and lock buttons the blue led pops up. But it doesn't remote start it. What's the issue?

2024 Prado

Tue, 03 Dec 2024 09:24:49 +0000

Hello. I installed evo-one (002B04683100) on 2024 Prado. Programming and decryptor were successful, but when I connect the 6-pin connector, all the LEDs blink

Why alarm went off after the remote start (3xlock)?

Fri, 29 Nov 2024 18:46:13 +0000

Do you know why the suv alarm went off after the remote started the vehicle? Is there any option I forgot to select? Setup as stand alone with 3x lock to start. SN: 001a07 531903 2018 Nissan rogue sport

BMW F15, F30...

Sun, 17 Nov 2024 00:51:06 +0000

Hello. I wonder why you don't include BMW F15, F30, etc. in the Fortin list? It's a simple logic: After the bypass relay is turned on (key in the coil), after 2 sec. pulse on a start-stop for 1 sec... After 3 sec. f pulse to the brake pedal for 5 sec. and after 2 sec. a start-stop pulse for 1 sec. (500 Ohm...or 680 Ohm...or 1000 Ohm). I'm struggling to put this together with some kind of autostart, but it would be easier with Fortin.

Fit to my car

Wed, 16 Oct 2024 01:22:05 +0000

Hi which device fit to my car Audi A6 C7 3.0TDI 2012?

Can Evo-All do 3x Factory remote start on Subaru 2019 Ascent with Push-to-start?

Sat, 05 Oct 2024 01:28:53 +0000

Can Evo-All do 3x Factory remote start on Subaru 2019 Ascent with Push-to-start?

2015 Corolla with an automatic transmission flashes 4 red flashes.

Sat, 07 Sep 2024 18:56:21 +0000

I have a 2015 Corolla with an automatic transmission start button.

Installed with THAR-TOY6 T-Harness & EVO ALL

The device flashes blue when opening or closing the doors, but when trying to operate it with the remote, it flashes 4 red flashes.

Flash blue once before red flashes

Please see the attached video.

https://photos.app.goo.gl/6rfod5uAwRBQ7MgUA

Toyota Prius V 2012 EVO-ALL 4 RED FLASHES

Mon, 19 Aug 2024 01:11:44 +0000

I installed an EVO-ALL on my 2012 Toyota Prius V (Hybrid, push to start) in standalone mode. When I try to remote start the car using the OEM LOCK-LOCK-LOCK sequence, the red LED on the EVO-ALL turns on, waits a few seconds, and then flashes four times. The car doesn't start, and the dashboard doesn't turn on either. Additionally, I've noticed that the security red light was flashing during the start sequence. The serial number is 001A07 076831. I've double-checked the wiring and FlashLink programming, and everything seems correct to me.

Can someone help me?

Lexus LX600

Mon, 22 Jul 2024 10:36:00 +0000

Hello. Does standalone (38-2) not work on Lexus LX600?

Reason why turned off after remote start

Mon, 29 Jan 2024 01:01:43 +0000

After installing the Lock x3 remote starter and I checked work well. also I flashed the engine to turn off after 15 minutes. But there are situations where the engine turns off when I open the driver's door after starting the remote start. Even though it hasn't been 15 minutes.

It's happens sometimes. What's the problem?

can remote start be fitted to my car

Fri, 19 Jan 2024 08:42:23 +0000

Hi I live in the UK and have a UK spec 2019 VW Tiguan SEL 2.0TDi DSG 4Motion with STD key entry and start.To start the car I must have my foot on the brake pedal if I don't the car wont start.Can remote start be fitted to this car?

2012 Toyota Prius V

Mon, 08 Jan 2024 10:26:30 +0000

Hi, Just installed the EvoALL, after 3X lock the car will still lock 2times then start , is that normal ?

2019 fusion

Wed, 29 Nov 2023 10:29:56 +0000

I am currently installing a 2019 Fusion. 4.01 didn't work and I want to program 58.04 but it's stuck and the balls are spinning. what can I do?

2010 nissan patrol

Sat, 14 Oct 2023 05:34:12 +0000

Hello. For a 2010 Nissan Patrol (Euro), which instructions will work? And the firmware? StandAlone.

ُEvo One or Evo All, I don't know if the Evo All supports remote start on my car

Sat, 16 Sep 2023 08:36:15 +0000

Hello

I have 2013 Honda Accord 2013 push to start and I would like to add remote start.

Do I need Evo One or Evo all is enough?

I will install the system with t-harnesses THAR-ONE-HON3

regards

Just bought a VW Tiguan 2017 push to start receive only oem key but discover that fortin remote start is installed. that

Mon, 28 Aug 2023 20:26:32 +0000

An electronic gadget is installed on windshield blue and red light blink and written evo on it. Can I link my oem key to 3x lock??

DCRYPTOR'S LIMIT HAS BEEN REACHED FOR THIS CAR

Sat, 26 Aug 2023 08:25:04 +0000

I buy FORTIN EVO ONE ALL + THAR-TOY13 + FORTIN RFK441+ fortin flashlink tools

For long range remote start installation on Toyota Camry Hybrid 2020 plug to plug without cutting any cable

I followed the installation instructions, but it didn't work I installed the device and made a flash, and when opening or closing the door, it flashed in blue, but when pressing 3 times to close, the remote start did not work I tried to flash the device again but it stuck in (DCRYPTOR'S LIMIT HAS BEEN REACHED FOR THIS CAR)

3-locks-to-start stopped working after module flashing / added RF kit

Fri, 16 Jun 2023 16:37:48 +0000

Hi,

My evo-all used to working with the OEM key 3-locks-to-start before.

Then I bought the RM 942 RF KIT.

Flashed the evo-all to 78.70, and the antenna to 1.05 already.

I flashed my evo-all to match my vehicle:

* Toyota Sienna 2020

* Standalone installation

* Standard connection

* push to start

* No alarm

Enabled the H&H2 option and paired the RF kit keys successfully, with the hlpe from https://www.fortin.ca/en/qa/121700/rm-942-buttons-have-wrong-functions

Followed the DCRYPTOR PROGRAMMING PROCEDURE. All leds are off at step 5 indicating it's already programmed.

After all these, it seems everything are connected and paired correctly. The lock/unlock buttons on the RF kit work properly.

BUT neither OEM key 3 locks nor RF kit key remote start ([+] + lock) could remote start the car. After pressing the OEM key 3 locks, I can hear the evo-all or some car electric component making the small clicking sounds, and the car turn signal lisghts had a couple of follow-up flashing, which seems to me like the evo-all is indeed carrying out the remote start procudre. But car does nothing, no cranking sound at all.

Did I miss anything again?

One weird thing to me is that I think I installed my evo-all with a T-harness, but in the Flash Manager software, after I select TOYOTA, SIENNA 2020, PUSH-TO-START, STANDALONE, there is only STANDARD CONNECT option but on T-HARNESS CONNECTION option in the connection type selector. Is this the problem?

Thanks,

Gerry

Evo one cranks but no start

Thu, 08 Jun 2023 00:29:41 +0000

CX-5 2016, never starts on first attempt, usually 2nd one is successful but I wonder if there is anything that can fix this behaviour. Transmission is manual. Tried several solutions recommend on this site but still the same.

Remote stopped working, OEM 3x Lock to remote start still works, no light on antenna

Thu, 23 Mar 2023 01:17:22 +0000

I had my car serviced and now the FTX-64-2W remotes don't work. The lock/unlock and remote start all stopped working. When you press a button the remote flashes blue for a while and then 1 red flash. The light on the antenna module also doesn't come on at all anymore. ANT-FMH-2W. The factory ford key still locks/unlocks and when you press lock 3x the remote start still works. So I think the EVO-ONE is still talking to the car and the bypass and remote start is still working. Did the antenna module get fried? They replaced the windshield, could the antenna 4-wire cae be damaged? I checked this 4-wire cable and couldn't notice any damage. The car also had a dead battery when I got it back from service. 2013 Ford Mustang GT.

DCRYPTOR'S LIMIT HAS BEEN REACHED FOR THIS CAR

Sun, 19 Feb 2023 18:11:53 +0000

Hi guys. I am having these problem with this box. Could you help me please?

S/N: 001A07350177

Please and thanks you in advanced.

2017 Octavia (Passat)

Sat, 11 Feb 2023 07:05:16 +0000

Hello. I installed evo-all (standalone) on a 2017 Octavia. The car starts with the external input (yellow-black), but does not start with the OEM remote control. The blue LED lights up on the second press on the close button of the OEM remote control (that is, it does not light up on the first press). 001A07 414271

Evo one CHR4 dodge challenger 2010 no any action only security light flashing

Tue, 07 Feb 2023 16:45:48 +0000

2010 Dodge challenger SRT with stander key and manual transmition

Module programming okay

blue light flash every press lock

Remote start red light one and give 2 sound then off

dashboard securty light flashing

Evo one with Chr 4 T-Harness

please help

2017 Tacoma won't start

Thu, 02 Feb 2023 13:57:02 +0000

Installed EVO-ALL and plug and play harness. Programmed bypass with programmer and also in vehicle. Vehicle programming went as it should(lights blinked properly). Vehicle will not start, blue light on by pass does not blink when vehicle is locked. Checked all settings with programmer.