Questions & Answers - Recent questions tagged blue

Blue light keeps flashing step 6

Thu, 29 Jan 2026 21:45:19 +0000

Step 6, turning off the ignition but the blue light keeps flashing. Doesn't turn off or switch to red and yellow alternating. Rav4 2025 hybrid push to start.

How to add LED light

Wed, 26 Mar 2025 20:22:39 +0000

How do I add an LED light that will stay on blinking when "Armed" and go off when "Unarmed"? I have the blue LED light for it, just not sure how to wire it. Essentially have it "on blinking" when doors are locked and "off" when doors unlocked. Evo-One kit is installed 2008 kia sportage

Autostart does not work, Mazda 3, 2018, auto

Wed, 12 Feb 2025 08:53:20 +0000

My fight continues, I hope I win Initially I programmed the keys incorrectly and had to do everything again, I reset and flashed to version 71.47, I successfully programmed according to instructions 62681, I did everything step by step and everything went well, but when I press the car lock button three times to start the engine, the red then yellow indicator lights up, the unit clicks a couple of times and that's it, the engine does not start. EVO-ALL, Thar Maz1. It reacts to locking and unlocking and the blue indicator lights up. Please help me figure this out.

Mazda 3, 2018 step 13, solid blue light

Sun, 02 Feb 2025 16:44:23 +0000

I have EVO-ALL and T-HARNESS Maz1 at step 13 the blue indicator is constantly on, there is no reaction to the key, does not change color to yellow Mazda 3, 2018, automatic

When i try to remote start after install a blue light flashes on module but Jeep does not start

Fri, 15 Dec 2023 18:38:34 +0000

I finished installing and programming my remote start on my 2020 Jeep Wrangler w/o keyless entry. I have the after market remote start remotes and when I go to start it a blue light flashes once on the module but the Jeep does not start. Dash screen light comes on and so does the lights by the gear selector but that’s it.

NO FLASHING BLUE LIGHT AT STAGE 5

Thu, 19 Jan 2023 20:45:29 +0000

2014 VOLKSWAGON JETTA TDI AUTOMATIC TRANS
AFTER REPROGRAMMING EVO ONE 3 TIMES STILL CANT GET THE EVO ONE BLUE LIGHT TO FLASH AFTER TURNING ON IGNITION, BLUE STAYS LIT THEN WHEN IGNITION IS ON LIGHT GOES OUT UNTILL YOU TURN IGNITION BACK OFF THEN BLUE LIGHT COMES BACK ON?

FORTIN EVO-ONE W/
VWT1 T HARNESS
DATE 12/2021
s/n 002b04 248922
firmware remote start = 1.[26] hardware 7.0
BYPASS = 75.[41]
hardware 4.0
loaded suggested options on both with diesel option checked

Evo all stand-alone 07 Equinox blue light turns off as soon as I plug in the white connector

Sun, 18 Dec 2022 06:53:08 +0000

Guide #59161

module key bypass programming can not go past step 3

blue light will stay on until I plug in the white connector. I have verified there is no voltage on the ignition yellow (A1) wire when ignition is off.
Any help is appreciated thank you

evo-gmt1 no red light no start

Mon, 12 Dec 2022 18:25:24 +0000

2011 buick regal evo-gmt1 sn001A07v253955 . Blue light flashes with door lock / unlock . oem remotes. no red light , no start. thar-gm1 rev2 harness. what is the correct wiring diagram ? at the moment brown wire to can sw pin 1. brown with white stripe to green /gray parking lights . cannot get ahold of tech

Red light disappears and Blue light stays solid

Sun, 05 Jun 2022 02:22:04 +0000

Hello, I have a 2015 Infiniti Q70 and when i program the module, I can get up to step 8 without any issues. When I press the brake for the second time, the red and blue light comes on, but after about 1 second, the red light disappears and the blue light stays solid. I'm unable to complete the programming of the module. Verified all connections are tight and correct. Please help!

I can not get the blue light to flash on the module on the first step of programming

Sat, 05 Feb 2022 13:42:10 +0000

2013 nissan pathfinder 2013 nissan pathfinder

How to add a blue flashing light for when system is armed?

Thu, 11 Feb 2021 15:01:43 +0000

I want to add a flashing blue light to warn off vehicle burglar. I tried you white wire on evo all, but it's a staying a ground with car running or off.

Blue light never flashes

Wed, 14 Oct 2020 17:30:20 +0000

I have a 2020 ram 1500, tip key , gas model truck. When following the directions I get to step 7 which is where I get the red and blue lights when inserting the key but then my red light goes off where it should stay on and the next step completely fails as the blue light just goes out and does not flash when it should. Anyone have the answer to this issue or is there another wire that needs to be hooked up other than my 2 can high and low and yellow to ign?

Module appears to pass dcryptor, but still slow flashes blue when installed.

Sat, 22 Feb 2020 19:25:13 +0000

After returning module to truck after Dcryptor processs completes, the module still slow flashes blue when installed. The truck still starts with the key, remotely locks and unlocks, but will not remote start. The module does nothing but slow flash blue. I don't see anything in the instructions or troubleshooting about this problem.

Can not get past step 6 no blue light in step 7

Sat, 01 Feb 2020 17:05:21 +0000

I have a 2010 ford escape. auto trans and 6cyl engine.

I can not get the blue light to light for step 7. Checked all the can connections and even solidered them. they are correct as the instructions ask them to be.

HELP?

Can not get past step 6 no blue light in step 7

Sat, 01 Feb 2020 17:05:21 +0000

Mazda Failing Decryption process (not able to get a solid blue)

Sat, 11 Jan 2020 15:59:49 +0000

I have tried to run the exact process for initializing decryptor for a CX-9 install, starting with diconnecting the neg battery terminal and then connecting the steering wheel white terminals into the T harness,reconnecting battery power and then holding down the button on the Evo one module while plugging in the 6 pin connector. I have not been able to get the module to set the blue solid light. Anyone run into this?

Module was programmed correctly via flashlink

2004 Dodge durango evo one programming. blue light wont stay on on mode selection

Sat, 21 Dec 2019 19:38:56 +0000

So i hard wired everything. In the programming procedure. Blue light wont stay on. I checked everything is all in order. Does anyone know what is happening? Thanks

while programming, blue light goes off at key on

Sat, 14 Dec 2019 18:55:53 +0000

installing standalone evo all (EVO-CHART5) with T harness on 2007 dodge durango. I have made the connections purple from T to Green/ Red (a18), yellow from T to yellow(a1), plugged T harness behind key switch. Used flash link 2 and selected options c1 for lock 3 times to start. I plug in black plug to evo all while holding in the button and release on blue, plug all connectors in and when i turn the key on the blue light goes off. I have 12vdc on the yellow wire (a1). Turn the key off and blue light comes back on. I have verified my all my connections. I even did a master reset, downloaded the latest firmware etc. what else should i do?? I have installed 4 of these so far and i have never had this issue with the others.

Can't get the solid blue light

Sat, 12 Oct 2019 13:17:28 +0000

Hello.

I have a 2017 Jeep Patriot, pluged the t-harness to immobilizer, connected the 4-pin connector while holding the program button and all 3 lights keep flashing. How can I get the solid blue to program.

Thank you

Can'y get blue solid blue led

Fri, 11 Oct 2019 23:13:17 +0000

2006 chevy uplander evo one can't get solid blue led in step 1 programming

Can'y get blue solid blue led

Fri, 11 Oct 2019 23:12:06 +0000

2006 chevy uplander evo one can't get solid blue led in step 1 programming

no blue light

Wed, 08 May 2019 21:33:27 +0000

i can get everything to work for programming up to the point that the blue light is supposed to come on and i'm stuck not sure what else to try.

2016 Hyundai Accent won't start with t harness install

Wed, 08 May 2019 14:27:57 +0000

My car will start with key but not remote start theBLUE LIGHT STAYS ON CONNECT REST OF CONNECTORS TURN KEY ON LIGHT GOES OUT turn key off blue light goes back on can voltage is 2.7 and 2.5

2016 Hyundai accent standard key Blue programming light turns off when I turn the ignition on

Tue, 07 May 2019 13:11:38 +0000

When installing the Evo one on my 2016 Hyundai Accent the blue programming light turns off when I turn the car on and the light comes back on when I turn it off have the can wires on the right ones do I need the can wires to use the remote start?What options do I need to change the service number is 002B07144688

2016Q5 with push start

Sun, 10 Mar 2019 15:48:56 +0000

I got evo-one, when I finally made the setting as recommended by the installation guide:

c1, D6 and d2 and 32.6 38.2

now it attempts to start and it unlocks the car but it doesn't starts the remote won't work locking and unlocking doesn't work, the lights (blinkers) flash twice every one minute and the blue light stays on.

When I flashed with the latest version 75 something I couldn't get to program on the car the blue light never flash rapidly and it only worked on version 60 any help would be great.

Thanks

Evo all not flashing blue on step 10

Mon, 14 Jan 2019 16:40:48 +0000

When going through the installation process the Evo all does not flash blue on step 10. All wires are connected with the exception of the hood wire. I have tried firmware 74.32 like the guide suggests as well as 74.18 like the flashlinj suggests.

How do I get guide #37131 for CAN Bus programming?

Sun, 02 Dec 2018 00:07:08 +0000

The troubleshooting guide for my 2011 Kia Forte suggests that I reade guide #37131 for programming the CAN Bus only. I do not know how to find this guide on your site. Can you help? I cannot finish programming my EVO-ONE because it cannot communicate with the CAN-BUS. When I turn the key on when the blue LED is on solid, it just goes off til I turn the key off. No communication at all with the CAN BUS. The wires are correct per the wire diagram. The CAN High wire has 2.72v and the CAN Low reads 2.3V.

I Need Help!!

2nd Half of Bypass Programming Fails, Can't Get Yellow Light

Sat, 10 Nov 2018 00:32:24 +0000

2016 Mazda CX-5 Automatic Pust-Start
Evo-All THAR-MAZ1
Stand Alone 2 Key Programming
Guide 62951

Had trouble at first getting through the first round of programming (steps 1-12) as I was failing to get the yellow light to illuminate. Got some help from some other answers and finally succeeded by removing batteries from remotes, keeping one in far back seat while programming the other, and performing steps quickly. Made it through decryptor step successfully. I've run into trouble at step 17 (repeat steps 1-12), as I'm unable to get a yellow light despite a ton of attempts. I've tried ignoring my failure here and proceeding to try and start the car but it appears that the bypass was not successful, as the unit does try to start the car, but gives up after what looks like 2 attempts and fails with 3 flashes of the red light on the unit. The dash never activates and the security light continues to flash throughout the attempts to start.

No blinking blue light when programming in step 4 of install guide for a 2018 Mazda CX9.

Sun, 21 Oct 2018 17:19:51 +0000

I bought the EVO-One and the THAR-ONE-MAZ3 T-harness for a 2018 Mazda CX9. I got the t harness installed fairly easy but am having trouble programming. I hold the programming button while I connect the 6 pin main connector, release when the blue light is solid, connect the rest of harness, press on 2x but the LEDs never flash as instructed. I'm not sure how to proceed from here, I've reset the module and tried a few times. The 20 pin connector has a bunch of lose wires on the t-harness, should this be connected to anything? From my understamding only the optional parking light wires needed hardwiring, everything else was plug and play.

where does the A8 (dark Blue) wire connects on 2015 Nissan Armada Intelligent Key?

Mon, 30 Apr 2018 08:58:50 +0000

I just want to make sure that the meant by "The Driver Door Pin" where the A8 Dk. Blue wire connects is that switch located at the body frame and controls the inside capin lights?

is this is the correct interpretation?

Thanks

dark blue wire, driver door trigger - does not work

Sun, 28 Jan 2018 00:01:56 +0000

I have a 2011 nissan rogue intelligent key, I installed an evo one, everything works perfect, except the trigger of the driver's door (auto lights shut down ) dark blue cable, connect this cable to the negative of the door trigger, exactly as the instructions say , but I have the problem that when starting the remote start the vehicle turns on but after 2 seconds it turns off, check the problem and I find that when the remote starter start the dark blue wire gives a constant negative discharge and the sensor of the door trigger shows as if the door were open, I do not really understand what this dark blue wire is for and what function it has, disable it and the car lights normal, my question is what should I do or what is the problem, or I must configure thanks.

Jeep programming NO blue light

Thu, 11 Jan 2018 22:11:14 +0000

2016 Jeep Cherokee Evo All with Tharness 6, going through progamming and cant get past step 6, step 7 tells me to turn key to on and red light goes out, blue light coms on. Tried this several tiime, making sure I followed instructions to T, but blue light never comes on. One more thing...........I could not find the interior temp sensor, so i Never hooked up the yellow wire for it, does this matter? Please Help!

No flashing blue light during programming.

Fri, 08 Dec 2017 20:33:28 +0000

I have a 2013 Kia forte. I Installed the evo one using thar-one-khy1 t-harness. I have programmed both the remote start and bypass sides of unit but i do not get a flashing blue light during programming through can bus. When I turn key to on the blue light goes out and doesn't flash. I have verified that i have the can wires correct. They both show 2.3v. Vehicle does not have pats data wire or immobilizer