Questions & Answers - Recent questions tagged challenger

What do I need to let the EVO-RS9 on 21 Challenger 6-speed manual acknowledge a pressed clutch pedal for remote start?

Sat, 10 Feb 2024 16:36:20 +0000

Everything sets and works fine. I can stay in the car and activate the remote start, it will go through all the steps twice, but no start. If I stay in the car and do the same steps, the car will start as soon as I press on the clutch pedal.

Evo one CHR4 dodge challenger 2010 no any action only security light flashing

Tue, 07 Feb 2023 16:45:48 +0000

2010 Dodge challenger SRT with stander key and manual transmition

Module programming okay

blue light flash every press lock

Remote start red light one and give 2 sound then off

dashboard securty light flashing

Evo one with Chr 4 T-Harness

please help

No response from OEM Lock on EVO All with all T-harness

Fri, 25 Nov 2022 13:35:30 +0000

2014 Dodge challenger

After successful Programing including DCryptor process. EVO-ALL does not respond to OEM Lock and doesn't start engine. Installed with T-harnesses for ODB2 and Push Start Button.

Any help is appricated.

Evo one only responds when its in valet mode

Mon, 02 May 2022 15:18:19 +0000

Evo one s/n 002B04108567 programs correctly with 2010 dodge challenger standard key wire to wire oem key fob and blue light flashes after when pressing lock or unlock , yellow light turns on when starting the car. The problem is minutes later the unit appears to end in in valet mode , red light on the side near yellow cut wire is on. When I take the unit out of valet mode , red light turns off but I no longer receive the blue light when locking or unlocking the car with the oem fob. When I attempt to remote start the car 3x lock the eed light turns on then the yellow light turns on but the car doesn't crank at all and only attempts to try 1x even though programming is set for 2x attempts. Then I get 4 clicks or flashes from the module. I followed guide #94481 for installation and have tried the basic bear options with my flash link 2 updater on 59.02 and 74 38 and 1 25 firmwares. I notice to anytime I try to run the module on the FL updater the FL updater has to be updated each and every time with 4 05 ? Any help appreciated , no oem alarm

Dodge Challenger 2019

Fri, 29 Jan 2021 10:43:32 +0000

Hi

Will your immobilizers support keyless autostart(without key chip in car) for 2019 year Dodge Challenger?

Thanks

cant get horn to trigger or trunk to pop

Mon, 30 Nov 2020 01:22:01 +0000

I have a siren positive connected to E1 thick white wire and siren neg connected to orange/black wire and the siren works. I have the horn wire under driver side dash green/orange wire also connected to the thick white wire. Horn honks when arming evo one alarm but not sound when alarm is triggered. What am I doing wrong ? Which option in #12 should be checked , siren + E1 white - horn, right ? Also I've tried several different wires to get the trunk to pop with no luck ! I'm using factory fob that has trunk pop button. Evo one , wire to wire , no factory oem alarm.

2016 Dodge Challenger, EVO-ALL w/ CHR6, now throwing U0415 Check Engine Light

Tue, 01 Sep 2020 16:01:46 +0000

As Title indicates, post installation the client is getting a CEL U0415. It happened to me after programming but I cleared it and figured it was a fluke. According to him, per his Dodge dealer, they have seen this happen with aftermarket remotes starts and also stereos on the Challenger.

Any suggestions other than rolling back firmware? When tapping for 12V ignition I grabbed the incorrect wire first time around. It was pink/wht but didn't give 12V with IGN. The snake shows Pin 27 OR 31 at BCM, plug E. 27 was the wrong one, 31 was hardly pink/wht, more pink/yel but did give 12V with ignition.

I can not find the pink and white ignition wire (9 v)?

Tue, 09 Jun 2020 22:40:23 +0000

I have a 2018 dodge challenger v6 push button start and this is the only wire I can find.