Questions & Answers - Recent questions tagged check-engine-light

2022 Nissan kick check engine light

Sat, 19 Nov 2022 21:13:06 +0000

I installed a evo all stand alone with a rf kit on a 2022 Nissan kick everything works but the check engine light came on some communication codes faulty gas gauge and other things, I got it erased but every time I remote start the car it comes back on if anyone knows how to fix please let me know

thanks

After installing all warning lights came on in the display

Mon, 07 Mar 2022 08:38:06 +0000

After installing and following all instructions and diagrams my dashboard was lit up a christmas tree with all the warning light coming on

Check engine light on after remote start, low fuel warning light, AWD malfuction

Wed, 05 Jan 2022 13:13:09 +0000

On DEC.8, 2021 I posted my question "H-KEY 2020 TOYOTA RAV4 LE EVO ONE WITH T-HARNESS REMOTE STARTER INSTALLED - SYSTEM MALFUNCTION" and got answer. I did what recommand to do, evnen hardwiring CAN HIGH/LOW two wires and use RAV4 CAN connector plugged in ECU, no luck.

My rav4 remote start problem more like this after a few weeks oberservation

Use OEM remote or RFK442 remote, the low fuel yellow light show up after remote started, When going in the car, key in the key cylinder and turne to ON position, press brake, key taking over. The yellow low fuel light disappear, and fuel display needle moving up to level.
After a few times remote starting, when you try another remote starting, the check engine light show up, and screen also shwing "AWD System Malfuntion. 2WD Mode Engaged, Visit you r dealer"

The CHECK ENGINE light was P2067: generic fuel level sensor "B" circuit low. I am wondering that low fuel level sensor B dosen't powered up when remote started, then ECU set the CHECK ENGINE light. I reset it by OBDII, but it keep coming. If no remote starting, RAV4 going normal by the OEM key and no warning light.

Is this could be a communication issue between EVO ONE and RAV4 ? The IGNITION signal from EVO ONE should go power up fuel level sensor B when remote starting, but it doesn't.

Any idea? Could you please look at 2020 RAV4 LE AWD(Canadian version) wiring diagram, see how.

Thanks in advance!

2015 Highlander Check Smart key System light

Sat, 06 Nov 2021 11:29:08 +0000

2015 Highlander Push to start, I'm gettting the warning for check smart key system. I've changed battery's in the keys. Anyone have this issue? Do I need to update my module?

Why my evo all activate my check engine light on my chrysler 200 2015?

Mon, 03 May 2021 07:57:31 +0000

After few minutes running check engine light came on and says the codes are unknown. Codes are for Mitsubishi Mirage.

Check engine light

Sat, 27 Feb 2021 12:04:05 +0000

Check engine light after install Evo all on 2018 Chevy traverse LS

P0496 Code

Missing Fire and engine light blinking

Tue, 05 Jan 2021 23:54:22 +0000

1. 2010 RAM1500 GAS EVO-ALL Installed with RF641/ The installation was straight foward. It is done successfully

2. Sometimes remote engine starts with strange noise (It looks like it is trying cranking and missing fire???). Eventually, it started. This issue was started about 2 weeks ago after the installation.

It happened 2 times so far. After this issue was happening, Engine light is blinking and disappered / RAM Manual says that it is Emissions error???(MIL). I have not checked OBD yet.

3. Most of the time, it works fine. No issue at all. But, after remote engine started successfully, Tire pressure error came on and disappeared when I put the metal key

4. What is the problem?

5. I think my RAM need some delay before cranking. Can I re-program with Diesel delay option for GAS?

Engine error light - B2102 - IGNITION RUN/START INPUT CIRCUIT HIGH"

Wed, 22 Apr 2020 09:26:43 +0000

HI,

I have Evo-All + RF kit 912 on Jeep Wrangler 2012.

All works fine, very happy, but when Remote start the jeep I have an error on dash.

With obd computer the error is: B2102 - IGNITION RUN/START INPUT CIRCUIT HIGH"

I can clear the error, but at next remoted starts it come back.

With standard key the error dont appear.

Any idea to solve?

Thanks

remote works-check engine and esc lights now on

Wed, 05 Feb 2020 14:59:16 +0000

After install, the Evo-All Thar-CHR6 works great. No issues. However, the check engine and ESC lights immediately turned on. There are NO codes in the ecm, but the lights won't clear/shut off. Truck runs fine and everything with the remote start works as should. Anyone else have this issue. It's a stand alone unit and I don't have a trailer brake control. 2014 Ram 1500.

Installed EVO ALL on 2015 Infiniti Q50 and got a check engine light

Fri, 10 Jan 2020 23:10:24 +0000

Hello,

I installed the EVO-ALL NIST4 standalone remote start on my 2015 Infiniti Q50 and it works/starts up fine, but there is a check engine light. The code reads P0463 Fuel tank level sensor - high input. The check engine light turns on when I use the remote start and when I start the car regularly with push to start.

Can anyone help me fix this, please? Thank you.

If check engine light is on

Fri, 13 Dec 2019 11:54:54 +0000

If check engine light is on already.can I still install evo all standalone remote start in 2011 Cruze.

Will thar fort2 work with check engine light on

Mon, 26 Aug 2019 03:38:01 +0000

Installed thar fort3 with compustar on 2015 f150 and if doesn't work alarm works but it won't start, tried it as standalone and it still won't start. My check engine light is on because my truck is modified, i was told on here that it won't start because my check engine light is on. If i change it to thar fort2 will it start with check engine light on? Does thar fort2 have the same limitations as thar fort3 installation? Also i used another evo all when i was testing can i use the evo all with another ford f150 same year without reflashing it? Or do i have to reset it and reflash it?

Clutch problem ( check engine light) wrangler 2018

Thu, 22 Aug 2019 23:29:50 +0000

Check engine light comes on every to often because of clutch bypass using mr20 relay. Need scan tool to remove then ok for a few weeks then comes back in again. Wrangler 2018 standard key evo one + t-harness

After decrypt my check engine and airbag light is on.

Mon, 29 Apr 2019 19:31:22 +0000

All wires are hooked up right the remote start and oem alarm works great. I have done different options multiple times to no avail. Everything else works good just check engine and airbag lights are on. I have the fortin evo all. Car is a 2014 Fiat 500L

check engine light comes on and code reads can bus not connected

Wed, 30 Jan 2019 07:55:10 +0000

Hello. I installed the evo remote start on my 2016 dodge journey. When I start the vechile up it starts but then the display on the instrument cluster starts blinking and the check engine light comes on. When I got the code, it says can bus not connected but the vechile works as normal.

Check engine light on with codes when using remote start

Thu, 03 Jan 2019 11:03:45 +0000

Hello, installed evo-one in my wife's 2005 Yukon. directions very good with the exception of step three when hooking up E1 (+)Ignition2 - White wire & E2 (+)Accessory - Orange wire.

Identified six-pin connector to the left of the steering column. Cavities & wire guage do not correspond. Contacted associate at Chevrolet dealer, looked up schematic and confirmed/identified th following;

Cavity "A" is "Ignition 3 Voltage" - orange wire

Cavity "B" is "Right Turn Signal Switch signal" - Light Green wire

Cavity "C" is "Left Turn Signal Switch signal" - Dark Green wire

Cavity "D" is "Hazard Switch signal" - White wire

Cavity "E" is "Off/Run/Crank Voltage" - yellow wire

Cavity "F" is " Accessory Voltage" - Brown wire

Connected E1 (+)Ignition2 - White wire to Cavity "E" - "Off/Run/Crank Voltage"

Connected E2 (+)Accessory - Orange wire to Cavity "F" is "AccessoryVoltage" - Brown.

Vehicle starts and dies with the remote start and sets several body codes.

Changed connection of E1 (+)Ignition2 - White wire to Cavity "A" - "Ignition 3 Voltage" - orange wire. Every thing seems to work but still getting check engine light with remote start - up to eight codes,

Open Torque Converter clutch circuit

Shift timing solenoid

Open Torque Converter clutch pressure control solenoid circuit

O2 sensor heater circuit open

Seems I may need to jumper a voltage feed to Cavity "E" - "Off/Run/Crank Voltage" for remote starting operation? Please advise

Regards, Bob

Evo-All on 2014 Nissan rogue causing check engine and 4WD error lights

Tue, 13 Nov 2018 20:31:18 +0000

It is a 2014 Nissan Rogue with the flip key. Installed using guide 75221 back in March of this year. Install was done by soldering. There was no issues during install, and no issues programming the module. I remote started the vehicle for 5 cycles before customer picked it up. No error lights. Customer called last week (8 months later) and said the check engine light came on, and the 4WD error light came on. They took it to the Nissan Dealership and they said the remote start is causing the issue because it was installed incorrectly. #1 I have done this exact install over a dozen times this past year and no one else has has an issue. #2 why would all of a sudden after 8 months it suddenly cause an issue? #3 is it possible there is a lag in the CAN Bus that is causing the error similar to some of the Chryslers where I need to change the firmware? #4 Why would this install be done 13 times on 14-18 Rogues and only this one have an issue?

Honda Accord 2002 and check engine light code P1705

Mon, 08 Oct 2018 01:02:00 +0000

I installed Fortin Honda SL3 and the presitege remote starter on my Honda Accord V6 2002. The check engine code P1705 comes on and D4 flashes when I move my gear from park to reverse. I unplugged the remote starter and check engine does not come on. I need help... Thanksss

Why is engine light on when remote starting

Mon, 19 Feb 2018 16:57:59 +0000

Have a 2015 dodge charger SE AND the remote start cranks fine but the engine light is on during operation. I have checked all of my wiring and everything looks okay. However, when the car is started normally no check engine is on.

2017 Hyundai Sonata throwing CEL

Fri, 26 Jan 2018 18:12:06 +0000

I did an install on a 2017 Hyundai Sonata. I did the install and everything worked perfect. Flashed it to the latest firmware. 1 week later the check engine light is on and he is blaming the remote start and is demanding it torn out, which is not going to happen. I know a number of the chryslers need the firmware rolled back because of timing of signals on the can bus. Can this most likely be fixed by changing the firmware setting? I have not checked the CEL codes yet, and the vehicle is an hour away. I also do not have the serial number on hand, It was done with an Evo-All and Viper 4806V. I have done dozens of installs with this unit combination and never had an issue. I would really appreciate any help.

check engine light when using 3x remote start

Thu, 18 Jan 2018 11:48:22 +0000

Installed Evo All CHR6 in 2014 dodge dart, programmed successfully, vehicle starts upon 3x lock, and stops with additional 3x lock. However, when using remote start, it appears to trigger check engine light, and puts engine in "limp" mode, accelerating sluggishly. if I turn vehicle off, and then start normally, without remote start, it runs fine, but engine light stays on. I can reset the light, but as soon as I use remote start, it comes back. I have googled this issue, and it appears I need to connect to a different wire, but not sure which one - I suspect something to do with brake pedal. help please.

additional detail I probably should have added. I started with the firmware version 74 .29, per the install instructions, but that wouldn't program. However I noticed the actual flashlink manager app recommended 74.24. Once I had reflashed it to .24, and it then programmed successfully, took the key details, encrypted successfully, etc.