Questions & Answers - Recent questions tagged evo-one-options

How to extend engine working time after remote start ?

Sun, 30 Sep 2018 08:16:11 +0000

Hi

Is there option to extend amaunt of time engine is runing in idle after remote start ? 10 minutes is little to short I would like to extend to 15 minutes. Unit i have is EvoOne.

Regards Remi

remote won't work when in remote start 2014 Elantra

Sun, 17 Dec 2017 13:55:41 +0000

I am installing an evo one in a 2014 elantra , the remote does not work when i remore start 3x my car

car does not have an immobilizer , what do i need to do?

EVO ONE with Sienna Push to Start - D6 Option won't save

Mon, 02 Jan 2017 21:14:06 +0000

I have an EVO ONE with the latest flash update for both the bypass and remote start module. Will be installing in a 2016 Toyota Sienna with the push button start option.

The install guide specifies the D6 PTS option, however when selecting that option and trying to save with the flashupdater app, I get the error message "this device does not support that option" and the EVE ONE disconnects.

Is that D6 option not required on the '16 Sienna. Thanks.

evo-one installation guide rf252wv/rf25bv

Sun, 06 Dec 2015 19:54:20 +0000

hello,i need help for installation of evo-one with rf kit rf252wv/rf25bv, i install it to honda civic 2013 and im confused which wiring i will follow,it is the regular installation or the one came with rf kit,the quick installation guide rf252wv/rf25bv,and also when i get in to the evo-one with flashlink adaptor and check it out theres two option the bypass and remote starter,can anybody guide me for the option that i need to select for both bypass and remote starter....

Thanks..

C1 & D2, where are these options ?

Mon, 23 Mar 2015 19:49:32 +0000

I am trying to do a full reset on an EVO-ONE, and I can't find where to do it.

In the Flash Link Manager, If I click option 23, it sets the options back to factory, and I click save, and it looks like that saves the settings, but I want to fully reset the unit.

I also see it says C1 and D2 are supposed to be enabled, but I can't find where these settings are in the software and the version written on the programming note that came with the unit says V79.24.

How do I know if that is right, and where do I find this info on the site ?

The software says Flash Link Manager 3.52

Is there another software that I need to use?

I am using a Crime Stopper Revo-1 and I have the setting for the factory remote set to off, since my car does not support that, but is there another option to set for using the after market antenna unit ?

Thanks

why when I use the latest software ( 73.14 ) on the Evo-One it does nothing but ( 73.07 ) almost works

Wed, 11 Feb 2015 12:21:17 +0000

Im installing a Evo-One with THAR-ONE-HON2 why when I use the latest software ( 73.14 ) on the Evo-One it does nothing when programmed for 3x lock but if I use the minium ( 7.03 ) the Evo-One unlocks the doors and the yellow led comes on like it is trying to start but no power on the ing and start wires, then it shuts down then does the same thing ( like it is trying to start a second time. Opition C1 and D2 are on, I tested the T-harness it is ok. I checked with a test light there is no power coming out of the Evo-One no Ing, no starter

Why did I get conflicting information from the techs when I called?

Mon, 02 Feb 2015 18:17:05 +0000

I have installed a Evo-one in my wifes 2013 push button Altima. When I called several times one tech said I should push the letter "o" when programming options with the Flashlink updater. The other techs said I should always use the configuration tab when programming and never use the letter "o" method. The one tech said he uses the "O" method all the time as he is an installer also. I also found the instructions about what each option did very lacking. it should be explained that one side is the Remote Starter and the other side is the by-pass. I would have saved much time if that were explained better, or at all in the instructions. Unless i just overlooked it somehow. I also had to hardwire the brake in order to prgram the rf kit i used, it would not read the brake through the can wires.