Questions & Answers - Recent questions tagged evo-one-programming-computer

evo one remote start works, but no accessory power until i get in and turn the key

Tue, 08 Jan 2019 22:19:00 +0000

well basically.... the title. 2004 350z, i have option 2.3 enabled like it says in the guide, not sure where i'm going wrong

No flashing blue light during programming.

Fri, 08 Dec 2017 20:33:28 +0000

I have a 2013 Kia forte. I Installed the evo one using thar-one-khy1 t-harness. I have programmed both the remote start and bypass sides of unit but i do not get a flashing blue light during programming through can bus. When I turn key to on the blue light goes out and doesn't flash. I have verified that i have the can wires correct. They both show 2.3v. Vehicle does not have pats data wire or immobilizer

Programming features on evo one

Tue, 05 Dec 2017 14:03:42 +0000

Question : so is there any way to remote shut off car after remote start is on?

at the moment the only way to shut it down is with the brake switch..

Q: Also the heated seats work with remote start, can the rear defrost work as well ? and if so how do i get defrost to work?

Q: when i change options in the unit with the flash link do i need to on the internet or can i just hook into the unit at the car with the computer and flash link and click on the options i want and hit save?

Again You Guys are Wonderful.

Great product as well

Thanks

Change EVO ONE options without flash link 2

Fri, 12 Feb 2016 13:41:58 +0000

If I didnt have flash link 2, how to select specific option using valet switch?.

Can't get past the key bypass in the programming all is well until I put the key in and turn to the on position.

Sun, 07 Feb 2016 18:52:15 +0000

After the flashing it was suggested that I disconnect the door lock and unlock wires, program and reconnect them. Is this the case? 2007 Honda Civic evo-one with a t-harness

Evo-one on 2010 sentra does not remote start

Mon, 11 Jan 2016 19:26:57 +0000

I followed wirecolor.com instructions and got the evo-one to program CAN and all that so i know im on the right track, but when i push lock three times on factory remote it does not start

EVO-ONE Remote start works, DCryptor bypass does not.

Sat, 12 Dec 2015 17:28:08 +0000

2004 Lincoln Aviator with PATS

One key only, marked with an S

Programming method 3, EVO-ONE.

I cannot get the immobilizer bypass to allow starting after DCryptor is successfully programmed.

Wiring as follows:

A1 = Lock
A2 = Unlock
(Do these need to be wired to Arm/Disarm?)

Reset bypass unit programming. LEDs alternate rapidly.
Unplug unit. Plug in unit (6-pin first)
Hold key against ignition barrel
Trigger remote start (Fortin 2-Way RF antenna)
Start successful
Remote stop. Stop successful.
Repeat 3-6 successfully.

Unplug unit

Bypass Programming:

Plug in unit, holding programming button
Release on Red.
Plug in all connectors
press program button. Red flashes off and back on
insert key, turn to on. Yellow light is comes on. Red light turns off.
Turn key to off. Yellow light is off, red light remains on.
Turn key to on. Wait. Red Yellow alternating flashing.
Turn key off, unplug unit.
take to computer, plug in, launch Fashlink manager 3
Unit red light is on
Vehicle selected is Lincoln Aviator 2004
Open DCryptor
Follow steps until successful message received. Unit red light remains on.
Unplug unit from computer and reinstall in vehicle, 6-pin connector first.
Attempt remote start. Start fails.
1. Remote Starter engages accessory and then ignition functions.
2. Faint red flashing on unit
3. vehicle relays are heard. Normal startup lights are on.
4. Starter is not engaged
5. Parking lights flash 4 times. (Note this is not the same as 4x immediate flash, indicating Valet Mode)
Door lock and unlock works fine.

Resetting the bypass allows for the remote start to function again, with the key held to the barrel.

Bypass options enabled:

A1, A2, A3, A4, A5, A6, A7, A8, A9, A10, A11

Additionally, this was tested with D2 both enabled and disabled.

Special Starter options enabled:

31.4, 20.2

Additionally I have:

Tried the above methods while holding the unit closer to the ignition barrel
Tested for voltage on the TX and RX channels, using both Key and Remote starts, on both the splice and the 20-pin sides, and observed the same voltage patterns.
Attempted swapping the TX and RX channels.
Tried all steps using firmware 71.31 and 71.28

Please provide any suggestions you may have, thank you for your help.

How to program the EVO ONE with flashlink programmer without it failing or disconnecting.

Wed, 09 Sep 2015 00:11:26 +0000

The EVO ONE I am trying to program starts the process then the green light goes out and it says fail to program unit disconnected even though it is plugged in.