Questions & Answers - Recent questions tagged ford-escape

Vehicle is shutting off when I open the door

Mon, 19 May 2025 03:46:57 +0000

I have a 2021 Ford escape I used the Evo with the Ford t harness I don't know if I set it up the right way but when I open the door the vehicle shuts off trying to get help with this I use the recommended setting don't know why it's cutting off when I open the door

Programing evo-all in 2013 Escape

Sun, 27 Aug 2023 16:03:12 +0000

Trying to install an evo-all with the thor-for1 t harness into a 2013 escape with standardkey start. Just want the remote start feature. Evo module came from my sons infiniti g37x. It has been reflashed with flashlink to be installed in the escape. Concerning that the flask status bar never goes over 25% beofore it "comepletes" the flash.

The module will not program to the car. With the standard 2 key programing, when I get to step 8 and press and hold the program button, the vehicel never starts and the bule and red leds come back on solid. If I try the Dcryptor medthod, with either key, the red led never goes out and yellow never comes one durring the key cycle steps. if I just plug the module in w/o holdong the program button, all the leds flask as if the module is not programed.

As the thor-for1 did not come with a C plug, I took the ones from the infiniti harness. however I do not have a A plug either, but not sure that is needed...?

2010 ford escape KEY-OVERRIDE-ALL

Tue, 17 Jan 2023 20:09:09 +0000

I'm installling the KEY-OVERRIDE-ALL with a DEI remote start.

When I attempted to program prior, I would see the LED start flashing, but programming didn't complete.

Now when I attempt to program, the LED on the module stays on and the security light on the dash flashes rapidly.

I've confirmed I have 12V on Red, Ground on Black, Ignition on Yellow, and remote start staus on Blue.

Is there anything else i should try on this module? The module was purchased new in December and hasn't been installed in another vehicle.

No Power to EvoAll 2008 Ford Escalp with Tharness

Wed, 14 Sep 2022 13:35:09 +0000

Hello, I have an Evo-All with a FordThar1 installed in a 2008 Ford escape for stand alone remote start. The vehicle will start and run with the Key normally, but iim not getting any power to the Evo-All. Ive verified this with a DVOM and use a second EvoAll module. Is my T Harness faulty? or is there something else ive missed?

Ford Escape will not disable RAP (retained accessory power)

Fri, 07 Jan 2022 22:54:14 +0000

I have A17 and A18 spliced into the green/purple wire at driver harness, one side 0V and other side ~11V. When driver door latch manually closed the door side of harness shows 10ohms, when door open shows OL so I know I have correct wire. How should setting be flagged?

2011 Ford Escape red light stays on during programming - SOLVED

Mon, 27 Dec 2021 17:42:57 +0000

Vehicle: 2011 Ford Escape

Evo All #001A07260304 installed with T-harness THAR-FORD4; plug-n-play install, teed connections to ignition switch, immobilizer antenna and OBDII connector; no wires spliced

Can't get the unit to program. Process: Hold program button, plug in data cable and release on red light. Insert key and turn on until theft light turns out. Remove first key and insert second. Turn on for 3 seconds, theft light goes out, turn off and remove. Last step says to press and release programming button within 5 seconds (this is where it gets stuck). Red light should flash 10 times and blue light should flash 10 times and ignition comes on and turns off again. When I press the button the last time, the red light blinks and just stays on.

I've tried the firmware downgrade listed in https://fortin.ca/en/qa/92073/faq-red-led-stuck-on . That link says to downgrade to v 0.99 but the lowest version for Ford appears to be 4.01. I flashed 4.01, power cycled in vehicle, reflashed v 71.52, unlocked settings and reset the unit. Still same results.

I've also tried testing the data bus. Hold button, insert data link connector, release button on blue light. Connected all other connections and turned key on. Blue light stays solid. Shouldn't it flash on data?

The yellow wire is not connected as it seems to be part of the T harness, but I've tested it for 12v on ignition and it is getting it. I don't have the valet switch or hood pin switch connected. What am I missing? I'm wearing out the plugs with all these connections/disconnections.

Red light stays on during programming and wont program the keys

Sat, 18 Dec 2021 01:12:17 +0000

I hVE 2008 Ford Escape. I installed the Evo all fort4 with the the t-harness. I have installed all connectors(1,2,3) and connected a relay to the lights as instructed in step 4. I plugged the black connector in while holding the button in and then let it go when the red light came on. I put in each key for 3 seconds each and then pushed the button in. It didn't start the vehicle. Red light stayed on teh whole time. It only blinked when I pushed the button in. What causes this and how can I fix it?

EVO-ALL to Aftermarket Remote Start. What connections should I make?

Sun, 29 Dec 2019 10:45:51 +0000

I have a EVO-ALL & THAR-FOR1 T-Harness along with a Crimestopper RS7-G5 remote-starter.

If I make all the (SOLID LINE) connections in the install manual including the Data Link connection, what other dotted line connections do I (have to make) or should I make to get the most of my install?

Should I make those connections from the EVO-ALL and vehicle, the remote-starter and vehicle, or the EVO-ALL and remote-starter?

Another confusion is the connection to the hood pin. Should i connect it to the EVO-ALL or the remote-starter or both?

Thank you.

evo-all on an escape doesn't initiate a start signal

Sun, 25 Aug 2019 13:23:16 +0000

2016 escape with an evo-all unit. the unit will not give a start signal on remote start. it detects the remote 3x lock (ie. blue light x3) but no red light. as per another suggestion the unit will give a red light when i ground the dk blue wire(ground while running) indicating that the unit is progammed correctly.

what should i be checking next?

Fortin EVO-FORT4 with parking light relay throws Brake Lamp Fault

Thu, 14 Mar 2019 09:37:24 +0000

Installed EVO-FORT4 with RG642W remote kit. Added Metro E5000 SPDT relay and (2) 3-amp diodes to have parking lights come on when autostart. Everything works fine, except when using the autostart the right rear taillight is dim and get the brake light fault showing on the information center. Does not do this when just using the key to start.

I do have the 12v+ with 10a fused to the relay. And the (2) 3a diodes tied to the purple/green parking lights + going to the relay. And finally the - from the relay to the brown/white to the EVO module.

Any idea what is causing the dim/fault message on the display?

Anyone else had their vehicle immobilized during install?

Sun, 23 Dec 2018 22:03:45 +0000

I was installing the fort-1 in my 2011 escape and it went ok until key decryption. I updated firmware, set options and plugged it all in with the T-Harness. The evo-all would flash about 18 times with all 3 lights but then wouldn't go solid green or turn red (unless plugged into the flashlink updater) and the car would still start with the key. I connected the green and white wire to a ground and the car dinged it's standard 3note ding, and now car wouldn't start at all even after I took all the fortin wiring out. All the lights still work, and the fab will lock or unlock, but I can't move the car and it doesn't respond to the key being inserted, the dash doesn't light up when turned on, and it doesn't start (I can't even shift into neutral to move it!).... I looked up related fuses and they were fine, then checked the other fuses until my fingers about froze and they all looked good. Please help. This has been frustrating and my landlord might not like my car where it is stuck for long...

Using the Evo Start 2 with the Evo-all

Sun, 28 Jan 2018 15:28:52 +0000

Hi there, I have an 09’ Ford Escape that I have already successfully installed the Evo-all into and it now works with my oem ford key fob. I bought the Evo Start 2 and am looking to set it up in the car as well but when reading the guide it mentions an RFA2A cable that I was never informed of. Do I absolutely need this for the Evo Start 2 to function with the Evo-all? Thanks

Do you have to have to keys for your vehicle to install a remote starter?

Sat, 13 Jan 2018 13:06:16 +0000

Do you absolutely have to have 2 oem keys for the evo fortin1 to be installed on a 2013 ford escape sel standard key start? I only have one key to my vehicle.

Is the parking light relay required on 2013 escape

Wed, 27 Dec 2017 16:42:41 +0000

Do I need to install a parking light relay for the stand alone with a rf kit and evo fort1

required connections for remote start only

Sat, 23 Dec 2017 23:56:39 +0000

2011 ford escape automatic using standard key for remote, what are the only connections i need (or what connections dont i need) to allow the remote start function to work. i know i need the hood and valet for safety. i have the evo RS evo-fort1 (t harness) preloaded all in one universal data bypass and interface module evo-all and following 32171 schematic

Stand alone install shows optional RF kit remote starter is it needed for 2011 escape standard key

Fri, 22 Dec 2017 22:00:27 +0000

The stand alone install schematic shows an RF- kit remote starter in an optional grayed out "box" will I need to connect the t harness and if so where will it be located?

Is the Driver door pin connection required for 2008 Escape

Sat, 21 Jan 2017 15:35:15 +0000

Installed Standalone. Did not make the Driver door pin connection. At end of programming sequence the ignition does not turn on while holding the programming button. I can hear the fuel pump activing but no igntiion. Is this a programming problem or is the door pin connection required ?

What is the power wire on an evo-all

Tue, 17 Jan 2017 18:30:24 +0000

Does anyone know the power wire on the evo-all? My lights require more than 10amps. The directions say if they require more than 10 amp to wire from battery to the power wire. It doesnt state or show on the directions what wire this is.

2014 FORD ESCAPE MIN./ MANDATORY CONNECTIONS FOR REMOTE START ONLY

Sat, 14 Jan 2017 15:11:55 +0000

What are the minimum / mandatory connections for remote start only option on 2014 Ford Escape with T harness, and minimum flashlink options. The lock-lock-lock function does nothing. the lock-unlock-lock sequece will turn on the ignition, but not start. Just wanted to do something nice for my daughter that appeared to be a short project, and now a 5 hour ordeal. Don't want to cut or splice any wires I do not need to.

Power wire on an evo-all

Mon, 09 Jan 2017 07:13:54 +0000

I have a 2011 ford escape. It requires 15amp for the parking lights. The directions say the t-harness is only rated for 10amp. If you require more hook the power wire directly to the battery with the appropraite fuse. What is the power wire on the evo-all and what size fuse should i use??

2016 ford escape cannot get the blower motor to turn on during remote start

Wed, 28 Dec 2016 12:19:33 +0000

2016 ford escape

installed evofort1 all funtions work properly except the blower motor will not work... any ideas

where is the wire for the start/stop switch on a 2011 ford escape?

Mon, 26 Dec 2016 11:52:25 +0000

On the 20 pin connector A13 it says to connect to the start/stop external control. What wire and where is it located on my 2011 Ford escape. Also all questions about the hood pin and valet switch say to hook them up to prevent starting when the hood is open. I understand the saftey but does it have to be hooked up for the remote start to function?

Trouble Programming and Starting

Mon, 19 Dec 2016 12:32:43 +0000

Programming for a 2008 Ford Escape. I have a EVO-FORT1 and have gone through the wiring and programming instructions. When I press the button, it illuminates the instrument panel fine, but does not start. I have the CAN High and Low installed to the OBD connector correctly. I have the yellow lead from the harness crimped to the yellow lead from the 20 pin white connector. I believe this is all the is required to be wired for it to be used as a remote starter. Can you help?

2008 Escape won't shut off

Tue, 06 Dec 2016 16:05:13 +0000

Installed an EVO FORT1 with harness in my son's 2008 Escape as a stand alone and everything works perfect except it won't shut off when depressing the brake pedal or turning the key to the off position, you must turn it off by using the key fob? Rechecked the options menu and everything appears to be correct.

Yellow light on EVO-FORT1 on solid

Sat, 26 Nov 2016 09:52:32 +0000

Installing EVO-FORT1 on a 2008 Ford Escape. EVO firmware 71.37. Flashlink Manger 3.62. Stand alone installation. Evo programmed correctly but when the red connector is plugged in after the decriptor process was done, ignition turns on and yellow light on EVO is solid. Blue light on EVO flashes with key fob lock and unlock buttons are pressed. C1 and D1 are on as well as F2.

2003 Mazda Tribute Evo One doesn't remote start without Key by the ignition

Sun, 15 May 2016 17:52:06 +0000

Hi,

I'm installing an AX-One unit in a 2003 Mazda Tribute with revo-1 remotes. I'm using guide #16941, because I can't find CAN HIGH and LO. I got a1, a2,a3, a10,a11,a20, e2,e3,e4,e5,e6 connected. Programming and dcryptor went smooth. Got the revo-1 remotes programmed also. If I hold the key by the ignition the car will start. Without the key by the ingition the car won't start.

I did noticed on Wirecolor.com a "Key sense" wire in the ignition harness. But I do not see where that connect to on the guide. Is that the wire I'm missing? Or is there something else?

Thanks,

2013 Excape, ignition powers up, no crank

Fri, 22 Jan 2016 15:44:18 +0000

2013 Ford Escape. Using the EVO-FORT1 with THarness. Have the flashlink updater. Unit is updated to 71.34. I have the THarness wired to the 4 wires from the 20 pin. The locks work. I did have a hard time getting it programmed to the car. I used the 2 key method. It was always the second key would not register the bypass. But it is programmed now. I hit the 3xlock, the red light turns on solid, then the yellow light comes on solid and the iginition powers up. after about 5-6 secs. both lights go out, and the iginition powers down. Then it retrys. solid red light, then solid yellow light, iginition powers up, after 5-6 sec, the red light flashes 3 times, then everything powers down.

The 2 CAN-BUS wires are connected. When it attempts to starts, the are 7.3v at the yellow/black wire that is connected to 20pin yellow wire (A1) and Purple/Yellow (16).

Does the door lock wires need to be used

Sun, 17 Jan 2016 05:12:29 +0000

Installed RS-160_EDP+ with Key-Override-all but not able to get the OEM keys to start remote start when pressed 3 times. Does the door lock and unlock wires need to be installed?

2015 Escape SE install not starting car

Mon, 11 Jan 2016 14:40:27 +0000

Hi, I have followed the wiring diagram for the 2015 ford escape install but I cannot get the car to remote start with the 3x lock. When I bought the Evo-all I was told that this would work but haven't had any luck. During programming, after inserting the 2 keys, it states to hold the program button until the car starts. The car never starts and the car reads "No Key Detected" on the dash display. When I press the lock button on the remote the evo-all blue led lights up so it appears to be getting the signal.

One key starts, the other doesn't in 2008 Ford Escape

Wed, 16 Dec 2015 14:02:37 +0000

EVO All, Installed in 2008 Escape and programed. Only 1 key will start the vehicle with lock pressed 3x. The other key will turn on accessories, however vehicle will not start.

cant flash 2012 ford escape

Mon, 07 Dec 2015 20:47:43 +0000

trying to flash evo all with the vehicle drop down list it wont let me choose ford escape 2012 and software is up to date, i can choose 2012 f150 and get up to 71.31 flashed will this work the same or do I need to do something else?

Can't get parking lights to work

Sat, 24 Jan 2015 12:21:19 +0000

I have a 2012 Ford escape using a EVO All with Tharness 3button remote start is working but cannot get the parking lights to work. I have tapped the wire and put power to it and all of the parking light come on just can't get the evo all to light them.

Do i need to program the evo all?

EVO All with Ford T-Harness on third push of lock button it turns on lights etc.

Sun, 28 Dec 2014 10:32:34 +0000

I have a 2012 Ford Excape with the EVO All and a T-Harness. Thanks to you it now works on the 3 push of the button but the starter does not engage. The lights come on and it sounds like it is going to start but the starter does not engage. Do I need to install a third party remote start module?

Thanks for all of your help.

Bill

Does the EVO all With T-Harness support 3 button lock for starting?

Fri, 26 Dec 2014 15:27:41 +0000

I have installed the EVO-All with T-Harness on a 2012 Ford Escape does this vehicle support 3 pushes on lock button to start? If not what do i need to purchase?

Installing EVO All with T harness in a 2012 Ford Escape EVO all will not program

Thu, 25 Dec 2014 10:03:19 +0000

I have installed the EVO All with T-Harness in a 2012 Ford Escape the module will not program it stays on blue when key is turned on.

Crimestopper REVO-1 with EVO-ALL

Sun, 21 Dec 2014 09:51:22 +0000

I have EVO-ALL installed with THAR and programmed and trying to add REVO-1 RF Kit....cant program remotes....does separate 12V fused power need to be connected to the coupler board (youtube video for this setup on 2104-2015 Ford Escape shows only the dataplug connection to the antenna board)

Remote Starter on 2014 FORD Escape with EVO-ALL & THAR1?

Tue, 16 Dec 2014 09:13:22 +0000

I was hoping to use EVO-ALL for stand alone RS but recently advised it wont work and I need to add a 3rd party RS starter....the Wire Color info for 2014 Ford Escape shows RS connections 42-53 at the Ignition Harness. Will the FORD THAR1 allow me to make all these connections on the THAR1 wiring without modifying car wiring? (12V power, IGN1, IGN2, ACC1, STRT1)?

Does the 2014 Ford Escape have to be Pushbutton Start to use 3X OEM RS?

Sun, 14 Dec 2014 20:04:55 +0000

If I reprogram with Flashlink2 will EVO-ALL act as a stand alone Remote Starter on non-PB start 2014 Ford Escape

Is EVO-ALL capable of remote starting 2014 Ford Escape with OEM remotes?

Sun, 14 Dec 2014 16:25:21 +0000

Purchased a EVO_FORT1 combo and installed and pogrammed with no issue but does not start vehicle

Can I install remote starter with only one transponder key.

Tue, 02 Dec 2014 23:36:52 +0000

I only have one key for my 2008 Ford Escape.

Escape 2013

Mon, 01 Dec 2014 23:29:05 +0000

Pourquoi lors d'un d

Cannot get EVO-ALL blue light flash with IGN 2011 Escape

Sun, 16 Nov 2014 22:43:23 +0000

Hello, Installed Evo-all as per connection diagram 3318 #2 on a customers 2011 Ford Escape. HA keys, 40 bit.(0v with key in cylinder,ign off) Loaded software version 4.18 as per diagram. Use programming procedure #3 for 2 keys, Blue light on, Turn ign on, blue light goes out, turn key off and blue light comes on, will not flash. Loaded versions 71.11 and 71.18. would not change with either versions, tried resetting module and reloading software again, no change. Have +12v on pin A1, pin A10 (light blue/black) to pin 4 (purple/gray) on ign barrel, Pin A20 (lt/blue/blk) to pin 3 (yellow/orange) on Ign barrel. Tested continuity of connections and are good. I am out of ideas, Troubleshooting guide claims CAN communication is not detected or wires mixed up, that's not the case assuming wiring diagram is correct. What are your thoughts? Thanks, Mike Unger.

I want a remote starter for my 2008 Ford Escape, which is easiest and best for me?

Fri, 14 Nov 2014 01:27:07 +0000

I would like to install a remote starter that is easily hooked up, preferably plug and play. Is there one here

2014 Ford Escape won't shut off

Fri, 17 Oct 2014 09:45:19 +0000

I installed a Evo-All and crimestopper RF kit in a 2014 Ford Escape approximately 2 months ago. All has been good, until this morning. Started car with the remote start and it would not shut off. The only way I could turn the car off was to disconnect the power to the Evo-All. The yellow light was on on the Evo-All before I disconnected the power. Any ideas please. I also installed the wiring harness for easier install.

Will lock, lock ,lock, start work an a 2013 Ford Escape?

Wed, 27 Aug 2014 19:20:45 +0000

Will Evo ALL work on a 2013 Ford Escape? 3X lock to start?

is RF kit required? for stand alone instal?

Sat, 23 Aug 2014 08:47:48 +0000

For ford escape 2012? Or I can start/shut the car with its oem remote? Will it need TBGM2 too?

Ford Kuga 2013 PTS, remote start after 2x lock

Tue, 05 Aug 2014 11:20:26 +0000

Hello, I have a car Ford Kuga 2013 PTS with EVO-ALL in standalone mode. After EVO-ALL updated on firmwire 6.71.18 (2014-07-22), engine starts after 2x press on lock button ! But must by 3x lock. How can this be ? And another question, is it possible to make remote start after button "lock" long press by 3 seconds ? Because we can accidentally press "lock" for 3 times on remote FOB or by pressing Keyless Entry Start button on door.

Ford Kuga 2014 Titanium S Auto with push to start - EVO ALL general questions?

Sun, 03 Aug 2014 22:08:16 +0000

Good afternoon.

I'm the proud owner or a 2014 Ford Kuga (Escape) 2,0 l TDCI Titanium S 4WD Automatic with smart-key and push-to-start. It has no security and I'd like to add that and also a remote-starter for hot days. I live I Spain so it gets very hot in the summer time. Anyway, I've checked the market and I've found out that the Compustar FT-7000AS Maxit would be a good choice. I like to add the Slice 2-way LED remote to the system and the EVO-ALL bypass module. What about factory udating the security part? Will it be better integrated? I would then only need to get the EVO-ALL for my remote start.

Also, I would like to retain the factory FOB functions like the remote start by 3x lock button, but I'm wondering what will happen when the car is remote started and if the vehicle needs to be stopped and started again the normal way (when carrying the factory FOB) or if I just could approach the vehicle and go? Does the car/bypass module know that the factory key is now present and would let me go ahead and drive? Or if I only use the Slice RF kit and unlock the car after remote start would it let me go ahead then without the factory key on me?

Brgds

Is the rf kit needed for 2014 ford escape stand alone install

Mon, 21 Jul 2014 22:27:01 +0000

I don't have an rf kit, the only stand alone install shows the rf kit install with it

Will not learn second ign key 2014 Escape

Thu, 23 Jan 2014 16:00:27 +0000

More of a information ticket as i figured it out

2014 Escape with THAR-FOR-1 t harness and evo all program #1 section 14 should read Press and Hold the EVO programming button untill ignition turns on then release.

As I spent about 1 hr trying to program. Also it worked and did learn the CAN bus but it did not turn off the ignition.