Questions & Answers - Recent questions tagged fusion

2013 Ford Fusion 1.6 Manual - Clutch bypass pinout

Sat, 28 Feb 2026 18:48:53 +0000

Hi,

Does the evo one support manual mode for the a 2013 fusion manual? Need the pinout from the bcm to bypass the clutch switch for remote start. Does it need to be driven by a relay? Also will the evo one detect the electronic handbrake via CAN? Can I use the t harness and then wire in the bypass separately?

2018 Fusion

Wed, 10 Dec 2025 14:58:16 +0000

I installed Evo-All on 2018 Fusion. The car starts, but the interior heater doesn't turn on. Is this how it's supposed to be?

2017 Fusion

Mon, 30 Dec 2024 13:41:41 +0000

Hello. I installed evo-all (001A07356265) on 2017 fusion. Doesn't start and blinks turn signals 2 times.

2019 FUSION

Fri, 01 Dec 2023 08:26:37 +0000

There was a broken wire in the underwing connector going to the underhood button. We fixed it and the remote start worked. Thanks for support.

2013 Ford Fusion remote start inop

Mon, 06 Feb 2023 15:49:05 +0000

I have a 2013 Ford Fusion with key ,installed with an Evo All unit with a T- harness 3 . The problem I have is that after the lock button is pressed 3 x you can hear unit chicking red yellow and blue lights come on like it trying to start vehicle. Then Im getting an red error code of 3 flashes , according to some research I believe that's a tach signal error. correct me if im wrong. All help and advice will be appreciated. Thanks

2011 Ford Fusion Standard key, only blows cold air after remote starter installation

Wed, 16 Nov 2022 14:38:58 +0000

I installed evo one remote starter on the 2011 ford fusion s, i hard wired all the wires, did not used t harness, but after installation, i was getting only cold air from the vents with starting from remote, i can change the blower speed. couldnt change the vent modes and the air temp.

if I start it with the key, heat blows only for couple minutes and it switch back to cold air it self, and has to restart the car to make it blow hot air for another couple minutes. any idea what could be wrong here,? any help will be appriciated,

2015 fusion. firmware version 4.01

Sat, 13 Nov 2021 12:05:15 +0000

Hello. I want to install evo-all (standalone) on 2015 Fusion version 4.01 (96151). Isn't it in the manager? It says 7152

FORD FUSION 2015 STARTS ONCE , AFTER THE FIRST START EVO ALL DONT START THE VEHICHLE

Tue, 26 Jan 2021 06:04:28 +0000

FORD FUSION 2015 EVO ALL STARTS ONCE , AFTER THE FIRST START EVO ALL DONT START THE VEHICHLE , it try to start but HORN ONLY AND NOTHING HAPPENS< PLEASE HELP

2012 ford fusion Module won't program

Mon, 25 Jan 2021 18:13:22 +0000

I just installed evo all for1 on a 2012 ford fusion . Connected can high/ can low, immobilizer, and ignition t harness. Flashed module, followed the program instructions and can't get it to program.

What wires need to be connected to 20pin?

Sat, 21 Dec 2019 00:48:54 +0000

I have a 2013 Standard Key Ford Fusion. I bout the Evo-all and T-Harness but am kind of confused. I know that I need to wire the yellow, light blue, light blue/black wires together. But what else do I need if all I am using this system for is remote start? Do I need to splice into the OBD-2 port and if so why?

Programming failure 2015 Ford Fusion standard Key w/ standalone + THAR-FOR2

Mon, 28 Oct 2019 13:44:26 +0000

Following instruction 59421 to install a stand-alone system with THAR-FOR2, I get to step 9 in the key bypass programming section. The vehicle's ignition turns on, but the blue light never flashes rapidly.

I've confirmed that the firmware is 71.46, and the 3 wires (Light Blue, Light Blue/Black, and Yellow) that come from the T-harness are properly crimped to the wires going to pins A20, A10, and A1. (crimped, and applied adhesive lined heat-shrink)

The CAN connections were connected to the wires at the pins as depicted on page 4 of the instructions - I noticed an error in the instructions, pin 20 on the diagnostic connector had a solid blue wire, rather than White/Blue. This wire was going to pin 20, and was twisted with the white wire on pin 19. To confirm proper connections, with the connector unplugged from the Evo All, I measured resistance between C1 & C2 to be 62ohms, and between C3 & C4 to be 61ohms - consistant with a standard CAN network.

I've tried switching C1 with C2, I've also tried switching C3 with C4 - no improvement.

Any help to get past step 9 will be appreciated.

Still trying to figure out WTF

Sat, 31 Aug 2019 15:20:23 +0000

It's been over a week and now, new problems. 1st the unit cannt be flashed anymore. Second the decryptor is not able to make a key, third, when doing the programing in the car itself, after the red and blue flash for 7 times and i put the first key in and turn to run, the red and yellow lights just alternate for the rest of the steps. nothing changes. The key code comes up on the dash but apparently this box wont program anymore. Only had it about 6 months. Does anyone have a solution or am I throwing this in the trash?

2016 Fusion gives KEY PROGRAM FAILURE message

Mon, 12 Aug 2019 15:33:22 +0000

I have a 2016 Ford Fusion SE with standard key ignition. Trying to install a EVO-FORT2 in standalone RS mode. I have connected the 4 CAN wires per the diagram and double checked the connections (even soldered them to ensure thay are solid), also connected the 3 wires (lt blue, lt blue w/black, yellow) between the 2 harnesses (D & A connectors). When I go thru the key bypasss programming, everything works until I get to step 9. The car displays KEY PROGRAM FAILURE, and then NO KEY DETECTED. No Blue LED blinking.

Fusion not disarming after locking with factory remote

Fri, 09 Aug 2019 13:36:45 +0000

2010 Ford Fusion with Evo-All and THAR-FOR4

When I lock the doors with the factory keyfob and wait over 30 seconds before unlocking with the Fortin RF642W fob, the factory alarm will sound when opening a door. If I open the drivers door first it starts counting down and can usually turn the key to disarm it. I have also had instances when a door is open while locking the Fortin fob it the alarm will also be triggered, after unlock and a door opening.

blue light doesnt come on after programming both keys

Sat, 30 Mar 2019 19:48:14 +0000

2013 Fusion, using T harness, Evo all in one, red and blue do their blinking thing then stay steady. put key 1 in and turn red flashes wait 3-6 seconds then remove key, red stays on. Put key 2 in and yellow flashes, wait 3-6 seconds, remove key, yellow stays on. Car turns on like its in run position then says no keys found. Blue light never comes on.

Can't finish programming 2009 fusion evo-all

Thu, 14 Feb 2019 20:29:58 +0000

Using EVO-All in 2009 Fusion Using connection #2i and Programming #6(1-KEY). Can't get passed step #13. When I attempt to do step #14, the yellow light stays on solid. No other lights come on or blink. Attempted many times with the same results. Checked wiring several times to make sure Tx/Rx aren't backwards.

2012 Ford Fusion Hybrid Compatibility

Fri, 14 Dec 2018 13:07:53 +0000

I've purchased an Evo about a year ago, installed everything and could never get it to work. It would set off the alarm instead of starting. Unfortunately, I had to return it. I would like to try again but I cannot get a clear answer. Is the system even compatible with a 2012 Ford Fusion Hybrid? There is no mention of the Hybrid on the site, just the standard. I would like to get a clear answer and purchase it again if I find out it should for sure work.

15 Ford Fusion standard Key will run only for 10 mins no matter what I set it to.

Fri, 19 Oct 2018 21:12:58 +0000

2015 Ford Fusion Automatic Standard Key Stand alone

I have Evo All hardware ver 6 software 4.01

It will run only 10 mins even if I will set it to 30 in diesel mode.

I updated the software to 4.02 like recomended by the flashlink but than my car will not start at all so I went back to 4.01 and same 10 mins at 15 set.

Please advise.

Evo All + THAR FORD 3

Sat, 06 Oct 2018 05:03:05 +0000

My Car FUSION 2015 (Standard-key)

I bought it from your store in Amazon Evo All + THAR FORD 3

https://www.amazon.com/gp/product/B077K7XBJN/ref=od_aui_detailpages00?ie=UTF8&psc=1

It is incomplete connections

Do I need extra pieces?

What should I do ?

The EVO-One is dead

Sat, 17 Feb 2018 15:19:14 +0000

Apon programing and seting the RF remotes, the EVO-One isn't doing anything. The setup, dcryptor, ect, all seemed to work work correctly but i can't get the unit to do anything. The volt readings at the connection seem to make sense as well. This is for am automatic 2007 ford fusion.

Does the evo all enable remote start options in my DIC?

Sun, 10 Dec 2017 14:22:45 +0000

Hello, I just installed the evo all guide 68911

Does this unlock the remote start options in the cluster? I see the guide says that the evo all supports heated seats but I do not see how to enable them.

Also, how do I shut the car off after I remote start it?

I remote started it to test, put my key in, turned the car to on/run, and then off, a couple seconds later it started itself again without me doing anything...

after step 8 the vehicle does not turn off nor does teh blue light flash rapidly

Sat, 07 Oct 2017 18:08:45 +0000

2015 ford fusion standard key

2016 Ford Fusion Push-to-Start diagram seems incorrect?

Fri, 21 Apr 2017 23:39:00 +0000

I purchased access to diagram for 2016 Ford Fusion with Push to Start and there are many wires that show connected to the ignition switch connector(standard key)....but that connector does not exist on push to start vehicles.

How to get the Dcyptor to work

Wed, 07 Dec 2016 00:50:41 +0000

Programmed the evo-all to a 2014 Ford Fusion all light lit up as it was suppose to, i unplug the unit and plug it into the Flashlink and tried the key dcryptor but it keeps saying invalid key data, tried all program step a few times even re-flashed the evo all, using a t-harness on this set up, im i missing anything. using as a stand alone system.

2011 fusion evo all with t harness standalone wont start car

Sun, 21 Feb 2016 16:44:40 +0000

serial number is 001a06 548613

when hitting the lock button the blue leds will flash each time, but no red led to start. Also there was no yellow led illuminated for the second key.