Questions & Answers - Recent questions tagged jeep

2017 Renegade

Fri, 12 Jun 2026 21:22:01 +0000

Hello. When I'm programming the Evo-All on a 2017 Jeep Renegade, the blue LED starts blinking after 5 seconds (after pressing the button), and after turning off the ignition, the red LED stays on continuously. I've already tried it on two modules.

2013 Jeep Wrangler,Manual Trans, EVO-One-942 kit, THAR-CHR5, will not remote start after ready mode entered

Thu, 29 Jan 2026 16:34:42 +0000

2013 Jeep Wrangler, Standard key (no OEM remote),Manual Trans, EVO-One-942 kit, THAR-CHR5, will not remote start after ready mode entered. I have followed install guide #63811.

After successfully entering ready mode and trying to remote start it will power the jeep up like itis trying to start it but nothing happens. After reading a few of the other question/answers it seems that a clutch bypass relay may need to be installed? I have found some information on wirecolor.com for the wiring of this. Does this relay connect back to the EVO-One somewhere? Installing a clutch bypass relay is not mentioned anywhere in the #63811 install guide. Perhaps you guys should include that in the guide.

2020 jeep renegade remote start

Mon, 12 Jan 2026 08:36:40 +0000

For information. I installed Evo-ALL on a 2020 Jeep Renegade. I specified the Jeep Compass in the manager. It only took CAN-1...I took CAN from the lower connector behind the BCM. From the thin green and brown wires. I took the parking light line back to the place where it was indicated on the previous model. Programming required opening the ON switch 10 times, as written in the manual. The PTS line was blue. The data line was yellow-blue.

2025 Jeep compass

Fri, 15 Nov 2024 00:57:19 +0000

Just a helpful heads up for everyone else. 2024 and 2025 Jeep Compass are same as 2023. Have done several now. Wired and programmed as 2023, identical, same connectors and wire colours. no problems.

2021 Jeep gladiator door lock control

Mon, 20 Nov 2023 00:08:53 +0000

Which system is best to use with the 2021 Jeep gladiator? I need remote start with t-harness and seperate door lock and unlock signal for aftermarket Door actuators.

How temporary disable EVO-ALL Remote Start

Tue, 11 Apr 2023 10:21:52 +0000

Hi, I'm considering to install EVO-ALL resp. EVO-CHRT5 to my Jeep Wrangler JK 2018 to get Remote Start possibility by the standard FOB.

My question, which options do I have to temporary disable the Remote Start function by FOB when I have to bring my car to a Jeep shop for an extended inspection? During the inspection, the Remote Start function by the FOB have to be disabled, after the inspection I'd like to reactivate the Remote Start function easy.

Which options do I have with the EVO-CHRT5?

Thanks

What connection did I miss? 2009 Jeep Compass

Sat, 01 Jan 2022 18:59:56 +0000

2009 Jeep Compass automatic. Kit is EVO-CHRT5 with a built in T-Harness and a EVO-ALL

Install is complete and programming procedure completes correctly at each step. No extra sensors- no hood switch or valet switch yet.

But there is no start with the remote. Vehicle starts normally with the key in the ignition.

I received a code in the box for wiring color setup and had to choose from about 8 guides. The displayed numbers mean nothing as the numbers at the top of the pages when printed show something different. I am using Guide 63651.

Besides the T-connections, I also connected the two yellow wires together. No other wires were connected and I am not sure what to do with the purple wire #18 as the drawing says it goes to the kick panel at item 3. What is it wired to?

A troubleshooting guide says to check for power at yellow/red and yellow/blue. I get nothing when trying to start.

New: I found a comment on a youtube video about hooking the green/red wire to the purple wire in the T-harness. That does not make any difference for me. Still no attempt by the car to turn on or to crank. Of course the horn honks and the doors lock each time I hit the lock button.

2005 Jeep Grand Cherokee brake wire relay

Sun, 12 Dec 2021 13:22:46 +0000

What relay do I use to wire directly to my brake? My evo all is not shutting down when the brake is pressed and tech support said I need to wire directly to the brake with a relay to reverse polarity.

Thank you.

2008 Jeep Patriot Evo-Alll slow flashing blue light

Tue, 14 Sep 2021 22:25:59 +0000

Here is what I have:

2008 Jeep Patriot Automatic Transmission, EVO-ALL, ProStart CT4311-TW, Jeep Patriot T-Harness.
After programming evo-all, it only slow- flashes Blue LED.

CT-4311 is connected D2D to evo all.

Yellow ignition wire from CT-4311 connected to Evo-All yellow ignition wire connected to yellow t-harness wire.

purple Mux wire connected to evo all.

CT4311 park lights wire wired to Jeep parking lights (white/purple)

when 3 lock press on factory remote.....nothing, slow flashing blue light.

when lock button on CT4311 remote pressed, CT-4311 clicks, no lock, park lights flash 1 time

when unlock button on CT4311 remote pressed, CT-411 clicks, no unlock, park lights flash 2 times

when start button pressed, ignition comes on, dash lights up, no start, no crank. Repeats 2 more times.

any suggestions?

I am thinking there must be something in the settings/options of EVO-All. I have the programmer and software. I just selected the "default" options when flashing.

thanks

Mike

jeep cherokee kk 2008 support

Sat, 08 May 2021 13:24:03 +0000

Hi!

I have a Jeep Cherokee KK 2008. It`s not mentioned in support table for evo-all, but as i think it`s similar to Jeep Liberty KK 2008, or Cherokee KK 2009. Am i right?

What basic kit should i buy - evo-all + thar-chr5?

Thanks in advance!

Jeep Liberty

Tue, 02 Mar 2021 09:26:08 +0000

Dear

I have a Jeep Liberty 2008. I bought the EVO-CHR.T2 model, but I couldn't get it to start with the Jeep key.

Do you have an email for someone from support to help me with the installation? I'm from Brazil.

Thank you

Giovane

2019 jeep cherokee key model

Sun, 31 Jan 2021 15:06:19 +0000

when will the 2019 jeep cherokee key be ready im trying to use the 2018 programing with chrt7 harness with no luck cant get the module to flash blue to programing

Parking / headlights flash 3 times every time brake pedal is released

Sun, 17 Jan 2021 16:53:16 +0000

Install is on a 2018 Jeep JL Wrangler manual transmission using Evo-One (S/N 002B04127001) and the THAR-CHR7 harness. Remote start is working but when brake pedal is released the parking lights and headlights, if they are on flash 3 times. Seems like the only time they do not is if parking brake is engaged or on the first push of the brake pedal after starting.

2020 Jeep Renegade Push to start. Anyone tried it ? Won't program

Wed, 06 Jan 2021 14:48:35 +0000

2020 Jeep Renegade Push to start. Anyone tried it ? The cables and connecters are exactly the same as a 2018 guide Programming wouldn't pick it up on an EVO ALL + CHR6

Can you start the Jeep with just your key?

Tue, 05 Jan 2021 17:50:35 +0000

Have the evo one all connected and works fine with the 3x lock. But when I tried to start it manually with the key it will not start.

Headlights flashes 3 times every time I take off

Wed, 30 Dec 2020 17:52:36 +0000

Just got the EvoStart 2 installation done by a dealer. Everything seems to work great except that my headlights are flashing 3 times every time I take off or slow down below 40 km/hr. Other drivers are not liking me right now...

JEEP patriot 2008 2.4 4*4 Fortin EVO-All +CHRT5 error p0513 in memory

Tue, 15 Dec 2020 05:19:57 +0000

Good day!
JEEP Patriot 2008 2.4 connected Fortin EVO-ALL via CHRT5.
Everything works as it should, the only moment that confuses and I want to solve this problem is that it gives error p0513 in the memory of the car. This happens when, after autostart, insert the key into the ignition switch, turn it to the "on" position and press the brake pedal. It turns out that when the control is transferred to the standard immobilizer in the key, the signal is lost and gives an error, but does not light the lamp.
The key is programmed.
After updating the firmware of the unit, I reset it to factory settings. It seems that I did everything according to the instructions.
What could it be?
Sorry for my english-gogl translation.

2005 Grand Cherokee oem alarm goes off after starting

Mon, 14 Dec 2020 17:24:49 +0000

When I start my Cherokee in the morning after sitting all night the OEM alarm goes off after the vehicle starts. The alarm will shut off if I press the unlock button and the vehicle will stay running but this is not an ideal situation. How can I stop it from doing this?

Jeep Grand Cherokee 2015 blue light wont come back on after turning the ignition off

Wed, 02 Dec 2020 21:32:13 +0000

this is a push to start jeep

I followed the steps:

1. plug in holding button

2. let go on blue and then turn the igntion on

3. after i press the button when the igition is on the blue light shuts off

4. turn the igniton off

and then it is supposed to be red and blue flashign but that hasnt happened for me

EVOALL will not learn key code in Jeep Gladiator

Sat, 20 Jun 2020 16:32:01 +0000

Hello. When I power up the EVOALL, I get to where the blue light is solid and when I turn the ignition on, the blue light shuts off. The module is then supposed to flash blue rapidly to learn the key code. The module lights do not turn on or flash. This is a stand alone EVOALL with the T harness. I am at a loss. I checked all of my connections. I have the latest firmware via FLASH-LINK. Thanks in advance.

LINKR-LT2 not updating status door locked after ready mode

Wed, 12 Feb 2020 16:35:16 +0000

I finally got my EVO-ONE and the LINKR-LT2 to remote start my 2017 Jeep Wrangler manual transmission... it works every time..

The only thing that technical support from mycar controls and myself haven't figure it out yet is "why after ready mode (neutral position, parking brake, brakes) the EVO-One will let me remove the key and unlock the doors or door depending of the initial command which I love (It does follow 1 passenger or more than one and unlocks the necessary door or doors depending on the remote sequence done to unlock driver's door or all doors)...back to the commandas... after I shut the door the car will kill the engine and after some seconds...I think is like 60sec. the car will lock the doors by itself.

Every time the car locks the doors...mycar control app will not show this status and only will have the green signal with doors unlocked,.. even though they are in fact locked.

Mycar control technical support told me that I have to choose an option to lock the doors with my factory remote and eliminate the automatic lock the doors command from the EVO-ONE or CAR ALARM (we are not sure who is sending the command... I think is the EVO-ONE but I need to confirm the blue led to be sure and haven't done it yet)

Can someone help me to know what setting number will set this option?,,,, The evo-one is super hidden and in order to remove it and have space to work under my steering column I have to remove the driver seat... jeep space in the front is super tight...

Thanks in advance

Natalie

Any help?

2005 Jeep Grand Cherokee Air Bag Warning Light

Sat, 04 Jan 2020 17:24:50 +0000

I just installed the EVO All with the T-Harness in my 2005 Jeep Grand Cherokee following the F installation guide. If I 3X lock to remote start the Air Bag Warning light comes on and stays on until the vehicle is shut off and started with the key fob. I do not have this light coming on if I start the Jeep with the key fob normally.

2018 Jeep Cherokee push button start cruise comes on but won't set after install

Sat, 16 Nov 2019 11:22:03 +0000

I tried to manually start but it still didn't set.

EVO-ALL in 2004 Jeep Liberty will not program

Sat, 09 Nov 2019 08:33:47 +0000

2004 Jeep Liberty, no factory alarm, with transponder key. EVO-ALL is installed with a Compustar CS800-S. Used installation guide #3317, Connection #1, Program #1. Firmware flashed is 74.[38].

I can get the bypass to enter program mode (solid blue LED). When turning the ignition key to ON, the blue LED turns off and nothing else happens. The guide says the LEDs are supposed to turn on and off BLUE - RED - YELLOW in sequence, taking up to one minute. I waited 5 minutes with no lights turning on. Any advice?

No Work, Program the EVO but do nothing the 2010 Jeep Patriot vehicle

Sun, 27 Oct 2019 12:49:22 +0000

hello install the evo RS, in a Jeep Patriot program but do nothing the car to turn on connect only the yellow cable you have to make another connection ?????

remote start in a 2018 Jeep Cherokee. pink/gray wire.

Sat, 26 Oct 2019 23:22:05 +0000

I can not find the IGNITION SWITCH HARNESS. I am looking for a pink/gray wire.

‘18 Wrangler - Remote start shuts engine off when doors are off

Fri, 04 Oct 2019 10:44:30 +0000

I have a 2018 Jeep Wrangler. I installed the EVO-CHRT6 Stand Alone, vehicle remote starts and everything works fine with the doors on. Remote start the vehicle, unlock vehicle, open door, get in, close door, hit brake, lights blink twice, vehicle is not using Fortin anymore. As a wrangler owner, we take the doors off. When I remote start the vehicle with doors off I follow a similar process. Remote start vehicle, unlock vehicle, get in, hit brake, vehicle shuts off and lights blink twice, which then I'll have to use the push button to start vehicle back up. How can I fix this? The remote start needs to recognize the doors opening and closing rather than just the unlock being pressed.

Clutch problem ( check engine light) wrangler 2018

Thu, 22 Aug 2019 23:29:50 +0000

Check engine light comes on every to often because of clutch bypass using mr20 relay. Need scan tool to remove then ok for a few weeks then comes back in again. Wrangler 2018 standard key evo one + t-harness

Do you have a wire diagram to connect a Viper 5806V and Fortin EVO-CHRT5 together?

Tue, 26 Mar 2019 18:54:57 +0000

I am getting ready to install a Viper 5806V and Fortin EVO-CHRT5 together in a 2015 Jeep Wrangler JK and am curious on some of the wiring for connecting the two. So do you have a wire diagram to connect a Viper 5806V and Fortin EVO-CHRT5 together for this vehicle?

2012 Jeep Compass Turns on but doesnt crank EVO All

Fri, 22 Mar 2019 18:16:37 +0000

2012 Jeep compass, programming goes through sucessfully but pressing lock 3x will turn on everything, but doesnt actually crank.

Using evo-all chrt5 harness. have yellow wire joined together, thats only one hooked up.

2005 Jeep Grand Cherokee Evo-One Keeps running with key removed

Tue, 29 Jan 2019 09:37:01 +0000

Issue developed recently. Jeep remote starts just fine. Sometimes it keeps running after the key has been removed. I think this happens when the Jeep has been remote started. When I am done driving and remove the key everything turns off, but the engine continues to run. It looks like there is a solid orange light on the device. If I disconnect the red connector the Jeep shuts off.

EVO-CHRT5 For Jeep Patriot 2008 I have factory fob, do I have to buy a separate remote starter or RFkit to make it work?

Tue, 22 Jan 2019 06:56:02 +0000

Hello all pro! Hi there, I bought EVO-CHRT5 (T-harness Included) for my Jeep Patriot 2008, my question is, do I have to buy a separate remote starter to be able to make it work? Im looking at the T-harness stand alone installation ( connection ) would this be the right connection for my Jeep? Yes my Jeep has a factory remote fob, but my problem looking at the stand alone wiring diagram is that one connector belong from T-harness ( black, 4 pin w/black and red blue white ) went to RF kit remote starter. do i have to buy this RF kit? can i just go along without making up this RF kit connection? And lastly the A2 and A3 from 20 pin EVO module which is the lock/unlock and the A13 start/stop, I bleieve this is an input which supposed to be connected from the vehicle lock/unlock door out put. but the A13 start/stop of 20 pin EVO ALL module where would this be connected from the vehicle? Also Im aware about the update and programming procedure I do have the the flash link updater im gonna be okay with that, Im just really confuse if i do have to buy a separate remote starter or RF kit to make my command start work. I hope someone can enlighten me Thank You so much !

factory alarm Problem with remote start

Sun, 06 Jan 2019 14:30:21 +0000

I have jeep grand cherokee 2013 (push to start) and install EVO-CHRT4 without the rf kit

when I trun remote start it was sounding horn and hazard lamp and not stopping

When trying to run the car with remotes, the alarm times work and the time does not work

Update my device to 74.29

Park lights and hood pin are not installed

Options:

C1

D1

D6

I hope to solve the problem

Best regard

Can you use a evo rs chrs5 on a 2008 jeep compass with a manual trans?

Mon, 24 Dec 2018 20:49:04 +0000

Looking to see if what I'm asking is possible or if it will ONLY work on automatic's.

2015 Jeep Cherokee Red light flashes 3 times and doesn't start

Mon, 17 Dec 2018 17:47:46 +0000

I am having trouble with the installation of an evo-chrt6 standalone t-harness on a 2015 Jeep Cherokee standard key (no push to start) All wiring is hooked up and confirmed correct. The unit is flashed for a standalone install with no alarm. I have used the recommended settings. I am getting a 3 flash code on the red light on the evo (parking lights flash accordingly with this code after the lock button is pressed three times but it is not cranking or starting. Looking at the instructions, 3 flashes indicates something to do with a tach although I do not believe this model vehicle has a tach wire to be hooked up. What should I try to get this working?

CHRT5 '09 Jeep Liberty turns off in 10mins of less after remote start active

Thu, 06 Dec 2018 19:16:58 +0000

CHRT5 remote start. Purchased and programmed by factory Fortin Dealer Mobile Accessories in Scotia, NY USA warmcarnow.com. August 26th 2018 Installed by me following youtube video instructions early September 2018

Lock x3 on factory key. Installed into 2009 Jeep Liberty. Automatic trans.
Has been working as it should up until about 2 weeks ago.

The Jeep starts up fine, then in less than 10 minutes of idle time shuts off by itself while parked and no-one has touched the pedal or ignition, entered the vehicle, or touched the buttons on the fob.

Evo CHRT5 on 2015 Wrangler does not flash after turning key to on and off

Sat, 03 Nov 2018 11:12:23 +0000

I started installing my remote starter and everything goes according to the guide, i get solid blue after pluggin in the EVO to the immobilizer, step after that the evo stays on solid blue after i put the key in turn to on and then off. i dont start the vehicle obviously but the light stays blue a solid bue.

I have the 4 pin black plug, 20 pin while, red plug and the 4pin white, in the instructions it says plug in the 2pin white connector which was not in the box. i ordered the right one for my Jeep, am i missing something? or do i need to do a different step.

2014 Cherokee Doesn't Remote Start

Tue, 30 Oct 2018 20:10:33 +0000

2014 Jeep Cherokee, Latitude, 3.6 AWD.

Programing was succesful. Dark blue wire (from 20-pin) grounded. Blue light flashes when lock button is clicked on fob (majority of the time).

Clicking lock 3 times does nothing. I haven't gotten it to do anything as of yet.

Did I accidentally puty it in valet mode (how would I know)? How should I proceed?

Thank you

Went to start 2017 Jeep Wrangler 3X Lock and Alarm went off.

Sat, 25 Aug 2018 22:55:17 +0000

Updated firmware and now when I cycle key and solid blue to flashing blue, when I hit the lock button all colors of the led flash and nothing works. The unit had been working for the last 14months with no issue.

17 JKU Base Model

Sat, 16 Jun 2018 12:16:07 +0000

Installing Evo-All with an Avital 4105L All connections are made from the evo to the 4105, when I press remote start the ignition comes on, evo lights yellow. But it does not crank. Tries 3 times then shuts off. I read about the green/red wire to the purple wire, but also have read not to do it on a wrangler.

2014 Jeep Cherokee STD key EVO-CHRT6 wont start Message on Dashboard

Fri, 11 May 2018 15:29:22 +0000

I installed EVO-CHRT6 stand alone on a 2014 Jeep Cherokee STD key 1 month ago. Last Friday customer called saying vehicle wont start with vehicle key and a message on dashboard says "key in igniton" with key in customers hand while door was open. Luckily I was near by and was able to go to customer and disable the EVO-CHRT6 t-harness from ignition and reinsert factory ignition harness. Message immediately went away and vehicle starts now with factory key. Is it just a random faulty Evo-all unit?

Thank you,

Amit

Jeep Commander EVO-One

Sun, 01 Apr 2018 23:52:47 +0000

Dear sir

I bought EVO-One and Flash-Link Manager, Not sure I've modified the setting or not.

my Jeep Commander and EVO-One never work.

anyone who can tell me the setting item by item on flash-link manager?

Jeep Compass 2012 Evo All and DEI 2 way installation

Sun, 11 Mar 2018 13:47:12 +0000

Hello, I tried Evo ALL and DEI. Alone Evo ALL is working, while working together i saw successful door lock and unlock. Then evo all remote started probably canceled by DEI. Summary, something is wrong wiring or settings.

Can you help me find out this problem, thank you.

EVO-ALL and Jeep Commander CAN BUS

Sat, 10 Feb 2018 11:40:28 +0000

Does the current firmware for the EVO-ALL read the CAN-BUS for door status on a 2008 Jeep Commander Sport? I currently own the EVO-ALL with THAR-CHAR4 for my Commander. The EVO-ALL is currently configured and function nicely. All options work (ex. remote start, alarm, parking lights, horn/siren). The Commander has no factory alarm. If I arm the EVO-ALL I can open ANY door and the siren will not sound. My wait time is 60secs. I know the alarm is armed because if I attempt to turn over the ignition the alarm sounds and the key sentry flashes as expected. Another question is have you actually had a chance to test the CAN BUS High and Low on this vehicle? I personally don't think the current firmware is allowing the EVO-ALL to detect the doors on the network. In relations to the alarm and doors I have played with Option G4. The option works on firmware ver. 7.34 but not on 7.22. However 7.22 is the only version that allows the alarm to work!

P.S. I also purchased an EVO-ONE. Do you think the EVO-ONE would do a better job of detecting the doors on the CAN BUS?

OPTIONS ACTIVATED:

C1, D1, G

No temperature sensor in lower dash panel

Mon, 05 Feb 2018 12:30:13 +0000

2014 Jeep Cherokee latitude

trying to hook up my EVO/ALL remote start and there is no

temperature sensor/lower dash panel

So have no connection for the (+) ignition yellow wire.

is there another place I can hook this wire up?

thanks

Lyle

2017 Jeep Cherokee ignition wire, No temp sensor

Sun, 21 Jan 2018 16:43:52 +0000

I see on your site where to find a 2016 ignition source but cannot find a wire on the 2017. Do you have any wiring diagrams or pics on where I can find a wire?

Ignition wire hook up jeep cherokee

Fri, 12 Jan 2018 17:40:15 +0000

2016 Jeep Cherokee. Evo all chrt6, is there a wire on the chrt6 tharness I can hook up the yellow ignition wire to since my truck dorsnt have a temperature sensor in dash?

T-Harness Jeep Grand Cherokee 2007 Plug Doesn't Fit

Fri, 12 Jan 2018 13:24:33 +0000

Hello,

I received the remote starter today but when I went to install it I came across a problem. I took the cover off the area behind the steering wheel and there are two connectors plugged in behind/underneath. Neither of these connectors will fit into the t-harness. One is yellow and too small, the other is black and too big (too tall). I took some pictures and shared them at the link below too:

https://drive.google.com/drive/folders/1iA4uGb2TRdX29bGx2yi-B_53DaWDHACp?usp=sharing

The Fortin box has a sticker which says EVO-CHRT5. The packet inside the box has a label which says THAR-CHR5.

The car is a 2007 Jeep Grand Chrokee 3.0 diesel. It's a right hand drive if that makes any difference.

Can you help please?

Thanks in advance!

While vehicle is already running can the Fortin remote start be used to keep it running after the key is removed?

Tue, 09 Jan 2018 22:36:16 +0000

While vehicle is already running can the Fortin remote start be used to keep it running after the key is removed? If so how can this be done?

Jeep Cherokee 2015 démarre à la 2eme tentative.

Fri, 05 Jan 2018 00:11:52 +0000

(Cherokee avec OEM remote starter et alarm, push to start) Avec Evo-all installé stand alone, le cherokee échoue toujours la première tentative. **Unlock pour alarm disarm, Led rouge, led jaune... fail... il recommence et démarre correctement. De plus, aparament, il ne démarre pas 1 fois sur 10. J'ai le véhicule seulement ce dimanche. Avez vous une idée?? J'ai deja eu un problème semblable sur cherokee 2014 std key, ca avais fini avec E400 en installation régulière. Pour le firmware utilisé, ca date d'il y a 3 semaines.

guide# 58591