Questions & Answers - Recent questions tagged key-override-all

Key-Override-All, is the red light bulb on the module supposed to stay lit still even after programming is complete?

Sat, 21 Jan 2023 01:13:49 +0000

Remote start works perfectly fine even after red light remains on after programming

2010 ford escape KEY-OVERRIDE-ALL

Tue, 17 Jan 2023 20:09:09 +0000

I'm installling the KEY-OVERRIDE-ALL with a DEI remote start.

When I attempted to program prior, I would see the LED start flashing, but programming didn't complete.

Now when I attempt to program, the LED on the module stays on and the security light on the dash flashes rapidly.

I've confirmed I have 12V on Red, Ground on Black, Ignition on Yellow, and remote start staus on Blue.

Is there anything else i should try on this module? The module was purchased new in December and hasn't been installed in another vehicle.

Will Evo key work on 06 Impala standard key

Thu, 03 Mar 2022 15:17:45 +0000

I was sold an Evo key that I am installing in 06 Impala. Can not find wire diagram for my standard key ignition. I am using data link connection but can not locate wiring for it. It is pre-programed for my 06 impala, but not sure of wire connections.

Key Override All stopped working

Mon, 29 Nov 2021 17:10:53 +0000

I have a 2013 Sequoia, came installed with Key Override All. I have a G key. The system recently stopped working. Here are some details:

1. had some (key) starting issues this summer so battery was disconnected and ECM was reset (hooking battery cables together)

2. Blue security light is on constantly

3. Unlock/back hatch functions were working.

4. Remote start function NOT working.

So I went with the tried-and-true 1st step....replaced the batteries. NOW THE KEY FOB WILL NOT LIGHT UP! (yes, I have tried several different battery orientations...still nothing. Will be purchasing a new set of batteries tomorrow.)

But still, even before the battery debacle, remote start stopped working. So, my question to you folks is: WHAT IS THE BEST COURSE OF ACTION? Is this any easy reset if I get the key fobs to work or do I need an installer to take a look?? Any recommended installers near Canton, OH?

I'm a handy gal, but I'm not down for wire-tracing or rewiring this dang thing. Dis tew much! (smh)

Thanks!!!!

key override all

Thu, 14 Oct 2021 15:40:27 +0000

Hello. Today I set the key override for the 2009 fit. When programming for the second pressing on the valet button, the LED began to flash, but was programmed. When we start the engine remotely. then it also flashes constantly. What's the matter?

Do I need the FLASH LINK UPDATER in order to install the KEY-OVERRIDE-ALL bypass module on a 06 F150?

Sun, 24 Jan 2021 22:29:31 +0000

I have a CRIMESTOPPER SP-402 ALARM REMOTE START installed. The white 4 pin DATA LINK cable that is supposed to connect to the EVO port on the alarm remote start did not fit and so I cut the clip off of the black 4 pin DATA LINK connector that supposedly goes into the ADS port of the CRIMESTOPPER ALARM REMOTE START module and plugged it into the EVO port. The connector did fit and I made sure the wires went in the port correctly as in the alarm remote start diagram. Did the programming on the bypass module as intended and I didn't get no blinking, off and on light,but just a steady red light. The truck did not remote start.

Why is my auto start starting for about 10 sec, turning off and back on again to do the same thing?

Tue, 05 Jan 2021 17:14:33 +0000

I have put an Evo key-overide-all and an Autostart in a 2001 lexus es300. Wired everything up and vehicle turns on normally and shuts down fine with the key fob however if I leave the vehicle running it shuts down and restarts after about 10 seconds.

Gone over wiring and everything is good. Double check programming on the Fortin but there are no changes to be make to the key overide. Only the update but there override is up to date.

Constant beep after key is removed and door opened

Sun, 02 Feb 2020 16:41:05 +0000

After parking my 05 handa civic (manual) turning the car off and removing the key, I open my door and there is this constant beep. It will stop when the door gets closed the beep stops. When opened again it continues.

1999 mercury grand marquis key-overide-all not programing

Fri, 27 Dec 2019 03:37:11 +0000

I am installing a crimestopper RS-5G and woking up a "key-overide-all" module and can't get it to program at all.

I help the program button while installing the 6 pin connector then the 4 pin the LED glows, I released the program button and turned the ignition key to on waited until security light went out turned off key and removed it waited 3 secounds and reinstalled key and turned until on and waited until security light went out, turned key back off and removed waited 3 secounds and pressed remote start, the LED on the key-override-all never changed (glowing all the time). the car tried to start but failed due to security (will start if I leve the key in and remote start)

Can you first verify the wire colors for the hook up? instructions say should be 1H ( connector is more like C)

Help please!

tundra 2006 immobiliser bypass

Sun, 30 Dec 2018 15:36:24 +0000

Hi, I have A 2006 toyota tundra cnd spec with factory immobiliser, on the website, it only give int-sl+ which only do the door lock, tried a used keyoverrideall like the diagram for the 2006 toyota sequoia (which is almost the same truck) but it doesnt work, it wont program, is there another option or do i need a spare key to make it work?

thank you

2010 tundra G key will not program key override all

Thu, 24 May 2018 15:00:03 +0000

2010 tundra with g key

I’m trying to program key override all
The unit is not programming the red light comes on solid with connections, truck starts for a second and shuts off, light stays solid even after 5 minuets.

all the wires seem to be connected properly

Using connection 20 page 14 and programming 3 page 17 of installation guide-6 wire connection 4 wire connection then power 4 wire plug. Not using the data wires just power/ground

need a little help

thanks

2010 tundra are 2 keys required for programming key override all?

Mon, 21 May 2018 11:12:51 +0000

2010 tundra with g key

I’m trying to program key override all and only have one key for truck

The unit is not programming and all the wires seem to be connected properly

Using connection 20 page 14 and programming 3 page 17 of installation guide

need a little help

thanks

key override all

Mon, 09 Apr 2018 01:12:38 +0000

In the instructions key override all (camry 2007-2009 ...) it is written that key override all is programmed for only one car. And if the LED flashes (as written in the instructions), what can we do next? Throw it away or what?

How do we pair Prostart starter with Key-Overide-All?

Sat, 13 Jan 2018 13:31:48 +0000

I have à Prostart starter with a Key-Overide-All and my car is an Honda Civic 2007.

All my wires and connections are ok.

The key is program with the page18 of the manual, where you disconnect and connect the pins and press the button x time so the lights goes on and off and everything is ok.

When I press on my Prostart remote the motor is cranking but doesn’t start.

Is there something special I have to do to pair the Prostart with the Fortin?

2002 Ford Focus / Key-Override-All / Will Not Program

Thu, 28 Dec 2017 22:21:53 +0000

Installed a Key-Override-All with a Crime Stopper 'CoolStart RS4-G5'. The Crime stopper works great with a key in the ignition only to satisfy the transponder.

I have tried several time to program the Override unit with no success. I am using Connection (1) with the Data Link. The RX,TX and IGN wires are connected directly to the ignition switch transponder. The Blue wire is connected to the Yellow/Black on the Crime Stopper (Ground When Running (Bypass Module).

I am using Program (2). I press the programming button and plug in the 'Black Connector' and the (6) pin connector. The red light comes on. I than program the keys and than hit the remote start. The red light blinks (3) quick blinks and thats it. The car never remote starts with teh 'Override' however the car will remote start and perform predictably as long as there is a PATS key in range of the transponder ring give me the understanding all is will except the 'Override' module.

Can you tell me what I am doing wrong?

reusing key-override-all for a second time

Wed, 27 Dec 2017 20:08:11 +0000

hello.i would like to re-use my key-override-all on a second vehicle (the first one is scrapped and i want to re install on another vehicle).if i program the key would it erase the previous one with no problem??and if not how can i erase and re-use please???

activation

Tue, 19 Dec 2017 14:23:45 +0000

Why don't you put on the activation card that its only good for 48 hours. I signed up and logged on to make sure everything was good to go Now when I'm ready to install I cant access any of the wiring diagrams and photos I need. If your not going to put installation instructions with your product then I should be able to access the info when I need it. What if I encouter problems that can't be resolved in 48 hours. I could have printed the instructions but not all of the pictures. I'm certainly not going pay extra for Installation instructions that should have come with it in the first place. I guess I'll just have to return the whole remote starter kit.

Can a key overide all be reset to use on another vehicle?

Sun, 19 Nov 2017 14:50:28 +0000

My client has swapped vehicles and the booth use the same bypass, can I reset the key overide all to accommodate learning the new vehicle?

key override all

Mon, 07 Nov 2016 00:32:18 +0000

how to update key override all?

key override all

Mon, 07 Nov 2016 00:29:31 +0000

how update key override all?

which evo solution to choose forr FJ 2008 ? also would all cables come in box? do i need T-harness cable to buy?

Fri, 06 May 2016 04:25:04 +0000

i want to buy evo-one or Evo-all for my wrangler 2013 and anotherr for my FJ cruiser 2008. the issue is

- which product to choose for which car, i am not finding enough information

- will the chosen product will have all necessary cables therefore i dont have to worry about buying more cables?

- updating firm to the right car, will i get it done prior shipping out the product from the disti? or shall inform them

Trouble Shooting

Sat, 09 Jan 2016 20:32:00 +0000

Im using the Fortin Override All with the CrimeStopper RS4-G5 remote start on a 2011 Toyota Corlla with the G-Key. Fortin module shows it is programed correctly. Started the car with the remote and the starter stayed engaged a few seconds after the engine started, then the engine shut down. Then without using the remote or key, the starter engaged again trying to start the car but the engine would not fire. Tried starting with the key and the engine did start and would run?

If my 2007 FJ Cruiser doesn,t have a transponder, do I need to connect the keysense wire to the override?

Sat, 14 Nov 2015 14:32:31 +0000

I,m pairing your key-override-all with a Cool Start RS7-G5 remote starter.

Cannot progran key-override-all on my 2005 ford freestyle

Sun, 20 Sep 2015 14:34:01 +0000

I replaced an existing remote start on my freestyle do to poor range. All went well until i tried programing.Initially when programed vehicle remote started on first try,after that the security light will flash all other functions work but no remote start. if i unplug override module and incert key in ignition vehicle will remote start. Red light on module will stay solid red until i press start button again to turn off accessories,than light will flash 8 times then stay on solid

Is Excalibur RS 260DP compatible with Key-override-all module?

Wed, 28 Jan 2015 19:11:09 +0000

Hi, I just got a Excalibur RS 260 DP and Key-Override-All bypass module to install on 2007 Scion tc but the RS 232 data connection wires between the remote starter and the module does not match, is it posibble to use or do I need to get a different bypass module? Thank you

how to reset key override-all Module

Mon, 05 Jan 2015 19:59:26 +0000

First, I programmed this module to be use on my 13 Honda Ridgeline but then decided to use EVO ALL module instead, so I decided to reprogram the KEY-OVERRIDE-ALL module to my other car 2006 Toyota corolla and it did programmed worked good until my battery was disconnected for few days, it kept giving me the hood pin error, I took the module out of the car to try to reprogram it, but when I connected to the computer it is showing the programming from of my truck 2013 Honda ridgeline instead of the programming of the toyota and is not giving me the option to select the car for programming, Do you think that it looked or do I need to reset it to start all over again?

Thank you.

where is the RX Data and TX Data plug for wires

Thu, 01 Jan 2015 18:30:01 +0000

I have a 2009 rav4 and i am installing the key-override-all for my remote starter

the purple/white and yellow/black wire go to a plug I cannot find. (rx and tx data)... I have the wire color print out with a picture that just shows a black 7 pin plug picture #4

i still have NO idea where it is. please help...

2010 F150 Wiring

Sun, 28 Dec 2014 09:39:29 +0000

I have the key over ride all, trying to wire it to 1010 f150 the red light comes on but never changes whewn I program it, maybe i have a wire wrong, using the excalibur rs 140 dp starter can you help me wire it all correctly very confusing instruction with both units

2011 Corolla wont start with remote start but will start with G key

Sun, 16 Nov 2014 11:47:05 +0000

install a compustar cs800 along with the fortin key override all with firmware 4.06. everything is hooked up and the fortin program correctly with the 10 blinks. When I try the remote start it will attempt to start the car, I hear the starter crank then it cuts out right before it turns over. When I use the key car turns on just like normal. When I unplug the fortin bypass and use the key it will do the same thing, try to start n cut out before turning over. I believe the fortin is install and program correctly.

Also before installing the bypass I tried to start it with just the remote start and samething. Car will attempt to start and cut out. Any help would be appericated. I try reprogramming the fortin like 10x already

TIA

UPDATE

So there was 2 IGN wire, hooked it up to IGN 1 and now it will work with the key in the IGN, but when I take the key out it will try and crank but wont turn over, I try to reprogram the fortin again but same thing.

2007 FJ Cruiser does not have the RX and TX wire at the ignition barrel?

Wed, 15 Oct 2014 22:38:06 +0000

I have a Key-Override-All bypass unit and it shows to connect the required wires at the igniton barrel area. The installation manual shows that the RX and TX wires are at the 7 pin wire harness (Pins 4 & 5 for Rx and Tx, respectively). However, the 2007 FJ Cruiser I have does not have the 7 pin wire harness, rather, it has a 4 pin wire harness (Blue connector - The wire colors are Green/Yellow, Blue/White, White/Black and another White/Black. ) Is there another place where the RX, TX, and Keysense wires can be wired to? The remote starter starts the vehicle but stops/dies after a few seconds, indicating that the car needs to have a bypass unit installed. Can someone please let me know where/how I can bypass the car's ignition. Thanks. (remote starter is a 2-way LCD Autostart)

Reprogram a KEY-OVERRIDE-ALL on a 2007 Mazda 5

Mon, 29 Sep 2014 02:25:22 +0000

Bought a used mazda 5 2007 that came with a KEY-OVERRIDE-ALL and its attached remote starter model OB-3471v (no brand?). The red light was OFF on the Key Override All module and I'm trying to reset it. I guess the car sat for sale for weeks with a dead battery... is it possible to re-program the module?

I tried following the program no 2 for the Mazda 5 (manual transmission) but the LED flashes as soon as I connect the datalink connector. What can I do now?

Thanks

Luc

FAQ - KEY-OVERRIDE Installation Supplement

Thu, 21 Aug 2014 14:12:46 +0000

This is an installation supplement for the KEY-OVERRIDE-SL, KEY-OVERRIDE-SL2 and the KEY-OVERRIDE ALL. It describes how to locate the required Data, Syncro, Security LED, Rx (receive) or Tx (transmit) wires at the vehicles PATS connector.

In some cases the colors of both of these wires differ and they may even differ between the same year of a specific vehicle. Because of this difference wire colors may not be listed and method 5 (below) may need to be used to determine the location of the wires in the PATS harness.

1. Refer to the individual connection types in the generic installation manual. Wire colors are listed in some sections for specific connection types for most vehicles. If the vehicle is not listed or the wire color does not match the ones listed then continue below.

2. Refer to the vehicle specific installation guides provided in the files section of the KEY-OVERRIDE-ALL. There are currently more than 250 separate installation guides which cover most of the vehicles covered by the KEY-OVERRIDE-ALL.

FAQ - KEY-OVERRIDE-ALL Programming Diagnostics

Thu, 21 Aug 2014 13:48:42 +0000

The KEY-OVERRIDE-ALL can only be programmed a limited number of times to a Ford/Lincoln/Mercury or Toyota/Lexus vehicle before it becomes locked and will no longer accept programming with a new vehicle. If you find that you are having trouble programming the module on a vehicle, the following simple procedures can be performed to determine the programming and locked status of the module.

1) To determine if the module is programmed
Unplug all connections.DO NOT hold the programming switch during the next step.Plug in the Data-Link Cable (Connector #1).This can be done on the bench with a 12VDC power supply. Red Wire: +12VDC, Black Wire: Ground.

If the LED remains off the module is currently programmed with a vehicle (To determine if it is locked see below).If the LED either flashes or comes on and remains solid the module is currently NOT programmed with a vehicle.

2) To determine if the module is locked
Unplug all connections. Press and hold the programming switch during the next step. Plug in the Data-Link Cable (Connector #1). This can be done on the bench with a 12VDC power supply. Red Wire: +12VDC, Black Wire: Ground.

If the LED turns ON the module is NOT locked and will accept programming with a vehicle. If the LED flashes the module is locked and will NOT accept programming with a new vehicle.

Please note the following:
The module is sealed at the factory with a tamper-proof sticker on the bag to indicate to the installer whether or not the module may have been previously used. If the seal is broken there is a possibility that the module have been programmed and may even be locked. If the tamper-proof sticker is still intact the module is neither programmed nor locked. The module can only be locked after it has been programmed. If the module is not programmed it can not become locked. The module can only be programmed if the firmware supports the vehicle, the module recognizes the vehicle, and the module installation is done properly (this does not include the remote-starter installation). All of these conditions must be met in order to properly program the module with vehicle. If you determine that the module has been programmed using procedure 1 above, and the vehicle will not remote-start, the problem exists in the remote-starter installation. Attempting to program with an other module will not fix the existing problem will only produce the exact same results. If procedure 2 above indicates that the module is locked, return the unit to your distributor for an exchange. We only honour exchanges up to 1 year past the data of manufacture on defective modules or modules that are locked. The Manufacture Date (MD) is indicated on the sticker of the module (MD: week-year). We verify all returns and non-defective / non-locked modules will be returned to the customer at their expense.

FAQ - KEY-OVERRIDE appears to program but Toyota/Lexus will not remote-start

Thu, 21 Aug 2014 11:18:43 +0000

The support article applies to remote car starter installations with either a KEY-OVERRIDE-SL, KEY-OVERRIDE-SL2 or a KEY-OVERRIDE-ALL on Toyota or Lexus vehicles.

Problem:

The KEY-OVERRIDE Bypass module appears to program with Toyota and Lexus vehicles, but the vehicle will fail to remote start. When remote starting the vehicle the LED on the KEY-OVERRIDE will flash rapidly instead of staying solid.

In some rare cases the KEY-OVERRIDE will fail to synchronize itself with the rolling transponder code during programming. The key being used uses a transponder code that the KEY-OVERRIDE module does not recognize. This situation will only occur during the initial installation of the KEY-OVERRIDE Bypass module and will not occur at any time afterwards.

Solution:

Use a valet key and re-program the KEY-OVERRIDE Bypass module.
Important: Do not attempt to reprogram the KEY-OVERRIDE module a second time using the same key. If this happens the KEY-OVERRIDE module will become locked and a new KEY-OVERRIDE module will need to be used to program using the valet key.

Note: The KEY-OVERRIDE Bypass module will allow you to program it two times before it becomes locked. Once it is locked you cannot unlock it by re-flashing the firmware, it must be re-flashed at the factory. This is a safety feature that prevents the module from being learned to multiple vehicles.

FAQ - KEY-OVERRIDE will not program with cloned key from a locksmith

Thu, 21 Aug 2014 11:13:55 +0000

Problem:

The KEY-OVERRIDE will not program when using a key that was cut by a either a locksmith or a retailer that sells counterfeit cloned keys.

A key that is provided by a locksmith is a counterfeit cloned key that is not stored as a "master" key in the vehicles memory. Although these keys will start the vehicle, they can not be used to program additional keys including a Bypass module. When programming a KEY-OVERRIDE module two authentic "master" keys must be used in order for the Bypass module to program properly.

Solution:

The two keys being used to program the KEY-OVERRIDE Bypass modules must be a combination of original keys that came with the vehicle, or an authentic replacement that was cut and programmed at a dealership. If an existing key is not from one of the previous sources; the customer must go to the dealership to have an authentic "master" key cut and programmed to the vehicle before programming the KEY-OVERRIDE Bypass module.

Installation in 2005 Ford Expedition key-override-all w/ RS1-G4

Sun, 09 Mar 2014 15:08:06 +0000

Followed Iinstructions that were provided with modules. Hood open not installed yet and park lights not connected yet. On your site there are two sets of instructions for this truck. One set shows to plug in plug number 2 fist then plug 1 and the other set shows to plug in plug 1 first then 2. I have tried both ways and no luck. The Key-Override-All never flashes 10 times. I only have one key and am following the procedure for one key. It blinks twice. When remote start depressed the lights come on the accessories start to run but no starter and the anti-theft indicator ion the dash begins to flash. Pressing the remote again shuts off everything, the KOA blinks 8 times and extinguishes and the LED on the RS1-G$ begins to blink. I think this is a feature of the unit as an anti-theft deterent. Had someone else check wiring and attempt to program and they were unsucessful, too.

Thanks

Simplest bypass module to install?

Tue, 04 Feb 2014 17:22:01 +0000

Thanks for your answer. Between the EVO-ALL, EVO-RIDE and KEY-OVERRIDE-ALL, is one simpler to install in a 2007 Prius?

if fortin plugs into Prostart remote car starter, do I need to wire up the 6 pin conn.?

Mon, 20 Jan 2014 23:05:49 +0000

ford-focus-2010

prostart-CT-3371-remote-car-starter

Fortin-key-override-all

where does the blue wire 6-pin-conn wire to in the remote? (-) while running????

Hooked where??? What does the blue wire get attached to???

Sat, 18 Jan 2014 20:30:03 +0000

08 Honda CRV. Instructions show "(-) While running" with an arrow pointing to a remote. What exactly does that mean??? What should that blue wire be attached to?

Possible to buy wiring only?

Sat, 11 Jan 2014 12:34:50 +0000

I have a key-override-all but none of the wiring harnesses that come with. Is it possible to purchase just the wiring for the module?

Thanks

Can't program the bypass for 07 Rav4

Sat, 28 Dec 2013 22:28:48 +0000

Using a key-override-all module. All wires spliced accordingly; however, when I attempt to program, the LED simply stays red after connecting the harnesses. Have tried several times to program and still no change.

When I attempt to start remotely, all dash lights turn on and a clicking can be heard, and then the dash turns back off. Can't figure out where I'm gogin wrong as all wires are setup the way the diagram shows.

Thank you...

Will my key override all work on a vehicle not listed? 2000 pontiac bonneville

Mon, 23 Dec 2013 18:37:02 +0000

I bought a remote start system it a me with a fortin key-override-all hardware vr:2 filmware vr: 4.06. I have a 2000 pontiac bonneville. It was not listed on the pre loaded vehicles will this still work on my vehicle?

ford taurus 2012, programmation key-override-all

Sat, 16 Nov 2013 08:08:12 +0000

Bonjour

J'ai install