Questions & Answers - Recent questions tagged leds

why don't the leds light up

Sat, 23 Oct 2021 15:26:43 +0000

When I plug in the evo to the black 4 pin connector as instructed no LEDs light up at all.

All 3 LEDs on EVO-FORT4 with first key in

Mon, 27 Sep 2021 13:20:01 +0000

2014 Ford Flex Std. Key w/EVO-FORT4 Soon as the fist key is inserted all 3 LED's stay lit solid...even all through 2nd key and back to the 1st key during programming. Vehicle can be put in 3rd key programming mode without module installed (door locks will cycle). Key sense wire is good, ignition chime comes on when key is inserted. Tried programming also without red plug plugged into the module. And checked with tech support using SN to make sure the module was programmed correctly. ?? Thank you.

Solid Red LED immediately after plugging in Data-Link Wire

Wed, 08 Jan 2020 17:42:26 +0000

I have an EVO-ALL unit with T-Harness THAR-GM1. I went through the initial steps for programming, programmed the unit using the Flashlink Manager software. Reinstalled into the car, remote start did not work. Attempted to redo programming. Unit began displaying a solid Red LED. I held in the programming button and inserted the Data-Link wire and it immediately displayed the solid Red LED again. I continued to hold the button in for several minutes and the Red LED remains lit. I then tried to reconnect it to Flashlink Manager, and it detects it. I tried to reinstall the firmware and it installs. I take it back to the car to try programming again, and again i received the solid Red LED immediately. I am at a loss as to what the problem can be.

No LED's when plugging in Data-Link wire

Thu, 04 Oct 2018 21:23:02 +0000

I'm using a Crimestopper RS7 with an EVO-ALL. Installation was working for a few weeks, then stopped. Now, when inserting the Data-Link connector while holding the button, no LED's light. When disconnected, the Crimestopper is putting out 12.0 Volts on the red wire, and 3.6 Volts on both the white and blue. After connecting to the EVO-ALL, the 12.0 Volts drops to 0.8.

So I hooked up this EVO-ALL in a different vehicle with the same setup (Crimestopper RS7), The same voltage drop occured, with no LED's. In this different vechicle, I then replaced its original EVO-ALl, and everything worked again. So I assumed I had a bad EVO-ALL.

Fast forward to today . . . I have a different EVO-ALL that I plugged in. But the same problem with no LED's. Any suggestions?

Ever wonder what the led's on the evo mean?

Mon, 24 Oct 2016 17:36:15 +0000

A simple and quick explanation!

Evo-all all 3 led flash

Wed, 23 Dec 2015 15:55:10 +0000

I have evo-all when the data plug is hook up all 3 lites start flashing if I move the plug around they stop, but when I stop they start flashing again, it does this even pluged into the flash-link updater. How can you program it if flash-link updater doesn't find it to be connected when it flashes

When plugging the data-link connector to the EVO-ALL all three LED's flash 25 times

Fri, 11 Dec 2015 17:46:15 +0000

When connecting the Data Link cable from the remote start to the EVO-ALL all three LEDs flash 25 times.

While debugging a door lock problem on a 2013 Subaru Crosstrek I did a master reset on the EVO-ALL, set the C1 option as directed and when connecting the EVO-ALL data link cable all three LEDs began flashing.

This is the second unit that this has happened with the same exact scenario. The first unit also had a bad data link connector causing intermittent power but after receiving the new unit and installing with the same lock problem I reset it and experienced the same exact problem.

Re-Flashing the unit with any version of firmware has no effect. Same problem. Both units communicated with the Flash programmer without any problems only when connected to the remote start do I see the problem.

I would have thought it was the cable but... The new unit worked perfectly with the same cable until I reset the unit.

Help please.

------update 12/14/15

Two things. When I say three LEDs are flashing I mean all 3 are flashing at the same time not sequentially. On the first unit I tried reprogramming the key but this was not successful but I don't remember the exact problem.

After reset and connecting with the Flashlink2 I can see that the key bypass is still there and active. Are you saying that I need to run the decrypter programming sequence again?

At the moment the Evo-All will not talk to the compustar at all except to pass signals through.

Thank you

LED color description?

Fri, 13 Dec 2013 18:39:39 +0000

I apparently programmed evo all succescully... Flshing lue led and all. Now whe i click the lock the blue led blinks as i do it. Then nothing happens. I use the key to start the car and yellow comes on and stay on till the car is off. Is this ok. What it means? Thanks .

Evo-All with Thar-char5 won't power on LED

Fri, 15 Nov 2013 15:15:46 +0000

Hardware version: 6

Firmware version: 74.08

RS232 protocol: FORTIN

Vehicle: Dodge Caliber 2009

I have connected the Thar-char5 cable and tested for power and ground. Getting 12 volts across them.

I can not get the lights to come on. I have followed your directions step by step.

Holding in the programing button and then insert the 4 pin data link connector.

And nothing happens. Would you know what the problem would or could be?