Questions & Answers - Recent questions tagged light

Blue light keeps flashing step 6

Thu, 29 Jan 2026 21:45:19 +0000

Step 6, turning off the ignition but the blue light keeps flashing. Doesn't turn off or switch to red and yellow alternating. Rav4 2025 hybrid push to start.

How to add LED light

Wed, 26 Mar 2025 20:22:39 +0000

How do I add an LED light that will stay on blinking when "Armed" and go off when "Unarmed"? I have the blue LED light for it, just not sure how to wire it. Essentially have it "on blinking" when doors are locked and "off" when doors unlocked. Evo-One kit is installed 2008 kia sportage

receive signal to start but parking light flash 3 times , and no more action ....any idea..?

Mon, 02 Dec 2024 07:56:56 +0000

my evo one on corolla 2019 , receive signal to start but parking light flash 3 times , and no more action ....any idea..?

Audi 2013 S4 DSG - Fortin ALL getting stuck on step 7 with 3 x red flashing lights

Fri, 22 Dec 2023 11:16:42 +0000

Just installed a Fortin ALL with the Audi T Harness on a 2013 Audi S4 DSG. UK right hand drive car.

When I go to try and get the unit to read the key data I am just getting 3 red light flashes on step 7, everything is fine up until that point and the car operates as normal.

When I then put the flashlink back onto the PC software it says invalid key data. Any ideas? I have checked all wiring, also checked status of CANBUS with zero issues showing so I know that wiring is good.

Serial no for module is : 001A07445150

evo-gmt1 no red light no start

Mon, 12 Dec 2022 18:25:24 +0000

2011 buick regal evo-gmt1 sn001A07v253955 . Blue light flashes with door lock / unlock . oem remotes. no red light , no start. thar-gm1 rev2 harness. what is the correct wiring diagram ? at the moment brown wire to can sw pin 1. brown with white stripe to green /gray parking lights . cannot get ahold of tech

impossible de faire la programmation

Mon, 05 Dec 2022 10:17:39 +0000

quand je branche module pour la programation je tien le bouon jusqua lumiere bleu et rouge ,je brancge mes connecteur ensuite jappuie 2 fois sur bouton pushstart . aucune lumiere allume

Red light disappears and Blue light stays solid

Sun, 05 Jun 2022 02:22:04 +0000

Hello, I have a 2015 Infiniti Q70 and when i program the module, I can get up to step 8 without any issues. When I press the brake for the second time, the red and blue light comes on, but after about 1 second, the red light disappears and the blue light stays solid. I'm unable to complete the programming of the module. Verified all connections are tight and correct. Please help!

2021 STI Radio does not turn off when ready mode is set

Thu, 02 Dec 2021 08:29:24 +0000

2021 Subaru STI 6MT push start

EVO One SN 002804220061 installed

When reday mode is set. Vehicle will turn off but radio stays on

also vehicle security indicator on dash keep flashing when key is take over

Thanks in advance

How to add a blue flashing light for when system is armed?

Thu, 11 Feb 2021 15:01:43 +0000

I want to add a flashing blue light to warn off vehicle burglar. I tried you white wire on evo all, but it's a staying a ground with car running or off.

Blinking amber light on start button 2016 CX-5

Sat, 12 Dec 2020 18:34:55 +0000

The module seems to work fine, I have completed every step in the installation guide. However, the start button does continuously blink amber/orange while the vehicle is running and does not stop until the engine is shut down. This only happens when started normally, not remotely. If I disconnect power to the EVO ONE, the car can be started just fine and there is no blinking light. I used the THAR MAZ 3 t-harness to install. I have been scouring the Mazda forums and have found no answer. Everyone says either replace the fob batteries (I replaced them) or visit the dealer. The mazda dealer wanted $150 to diagnose the problem, and then doesn't want to even look at it after learning the Fortin system was installed.

Blue light never flashes

Wed, 14 Oct 2020 17:30:20 +0000

I have a 2020 ram 1500, tip key , gas model truck. When following the directions I get to step 7 which is where I get the red and blue lights when inserting the key but then my red light goes off where it should stay on and the next step completely fails as the blue light just goes out and does not flash when it should. Anyone have the answer to this issue or is there another wire that needs to be hooked up other than my 2 can high and low and yellow to ign?

the evo does not detect the data

Sun, 26 Jul 2020 15:26:53 +0000

hi i have an evo one thats installed in a 2004 tahoe. followed guide 61101 and when trying to program the immobilizer bypass the blue light turns off and nothing else happens once the ignition is turned on. triple checked wiring and checked continuity. tried moving the wire to another leg of the bus distribution and that didnt work either.

am i missing some software parameter or something ?

SN:002B04 087218

tried software 70.18, 70.40 & 70.38

Evo all installed on 2018 challenger throws check engine light

Wed, 13 May 2020 18:41:29 +0000

After installing my evo all with t harness the 3x lock starts the car but throws on my check engine light. When I scanned for the code it show no active code, but the lights on my dash. I'm not sure what's being done wrong since I can't locate a code to reference anything to.

Remote started the car, but parking light not on

Wed, 06 May 2020 23:10:18 +0000

I installed EVO-ALL in a 2017 Infiniti QX70 with THARN-NIS1 harness using guide #90131. It is a stand alone remote starter programmed with 3X lock on OEM fob to remote start the car. The brown wire from the T harness is connected to the only red wire(pin 8) on the only 10-pin white connector at the BCM as it is depicted in the installation guide. I also confirmed with WIRECOLOR.COM picture and diagram, the red wire is the parking light wire for the car.

I test the brown with a meter when the car has remote started and I don't see 12V at the brown wire. I see 12V on the red wire when I turn the car light switch to parking light position.

Should there be 12V on the brown wire from the THARN-NIS1 harness when the remote is running the car?

Module appears to pass dcryptor, but still slow flashes blue when installed.

Sat, 22 Feb 2020 19:25:13 +0000

After returning module to truck after Dcryptor processs completes, the module still slow flashes blue when installed. The truck still starts with the key, remotely locks and unlocks, but will not remote start. The module does nothing but slow flash blue. I don't see anything in the instructions or troubleshooting about this problem.

Antenna light blinks constantly when truck off and locked

Wed, 22 Jan 2020 19:58:18 +0000

Installed the Fortin evo one 442 kit with antenna, is the antenna supposed to blink constantly blue when truck isn't running ?

2014 malibu t-harness installation parking light

Tue, 17 Dec 2019 08:51:12 +0000

hello, i am installing a evo-all on a 2014 malibu and the flashlink software shows A14 as the parking lamp. however the instructions i'm following 63361 state the parking lamp is wired differently with a module i am not using. can i safely use the a14 wire to the suggested gray parking light wire?

2015 Mazda 3 PTS no yellow light during programming

Wed, 11 Dec 2019 12:46:37 +0000

Under hood there is a pin where instructions show a blank pin for jumper. Installing Evo-All with mazt1 t harness

Can't get the solid blue light

Sat, 12 Oct 2019 13:17:28 +0000

Hello.

I have a 2017 Jeep Patriot, pluged the t-harness to immobilizer, connected the 4-pin connector while holding the program button and all 3 lights keep flashing. How can I get the solid blue to program.

Thank you

no blue light

Wed, 08 May 2019 21:33:27 +0000

i can get everything to work for programming up to the point that the blue light is supposed to come on and i'm stuck not sure what else to try.

2016 Hyundai Accent won't start with t harness install

Wed, 08 May 2019 14:27:57 +0000

My car will start with key but not remote start theBLUE LIGHT STAYS ON CONNECT REST OF CONNECTORS TURN KEY ON LIGHT GOES OUT turn key off blue light goes back on can voltage is 2.7 and 2.5

2013 Explorer wont complete programing

Sun, 11 Nov 2018 22:45:23 +0000

installed EVO-FORT 1/EVO RS to EVO ALL specifications found on web site, on 2013 ford explorer standard key, everything appears fine untill the final program step, when doing final flash the blue ligt blinks 10 times as it should, but instead of going off then goes to a constant yellow light? Ive cross checked wiring mulfibple times, I have verified 12amp power at the yellow wire and still nothing? any help would be greatley appricatied.

Is it possible to use my fog light toggle as my valet toggle also? If so, anything special?

Tue, 06 Nov 2018 21:31:17 +0000

I am using a EVO-ALL and '10 Charger Rallye

Where is the parking light harness so I can get to the negative parking light wire on 2010 Dodge Charger?

Sun, 28 Oct 2018 18:46:44 +0000

EVO-ALL Stand alone install with T- Harness.

Jeep programming NO blue light

Thu, 11 Jan 2018 22:11:14 +0000

2016 Jeep Cherokee Evo All with Tharness 6, going through progamming and cant get past step 6, step 7 tells me to turn key to on and red light goes out, blue light coms on. Tried this several tiime, making sure I followed instructions to T, but blue light never comes on. One more thing...........I could not find the interior temp sensor, so i Never hooked up the yellow wire for it, does this matter? Please Help!

2016 challenger check engine light on after 3x remote start

Tue, 26 Dec 2017 19:45:59 +0000

I have evo chart6 installed into my 2016 challenger and now only on remote start 3x lock, i get a check engine light, no code comes up when checked? I can start car with push button and the check engine light is not on. What is the fix?

I read on another dodge check engine light problem it was noted to flash with 74.18 Will this fix the problem?

I have flashed unit to 74.18 but I still need to know an answer as my son will put the unit in his car and I will need to know before I give it to him.

thanks

Steve

No flashing blue light during programming.

Fri, 08 Dec 2017 20:33:28 +0000

I have a 2013 Kia forte. I Installed the evo one using thar-one-khy1 t-harness. I have programmed both the remote start and bypass sides of unit but i do not get a flashing blue light during programming through can bus. When I turn key to on the blue light goes out and doesn't flash. I have verified that i have the can wires correct. They both show 2.3v. Vehicle does not have pats data wire or immobilizer

Murano 2011 Brake Lights Flash but doesn't start

Sat, 21 Oct 2017 13:05:22 +0000

Hello, I just finished installing the Evo NIST1 and whenever I press the key thrice, it receives the signal, both the parking lights and the brake lights turn on, and after 5-10 seconds, it fails to start, and the brake lights (and parking lights) flash three times and turn off completely. I did all the wiring correctly (I'm pretty sure) anyone have any ideas?

2012 Nissan Murano. Key light on dash. Doesn't go out.

Mon, 27 Mar 2017 17:46:44 +0000

2012 Murano PTS. EVO-ALL stand alone with Crimestopper Revo RF kit. Programmed fine. Works as it should. Is it normal for light to be illuminated in this particular application, or should the light go out?

parking lights jeep jk

Mon, 02 Jan 2017 16:29:08 +0000

I have the evo chrt5, im trying to get the parkings lights to work, I know its a - out signal white/brown. i also know i'll need a relay to convert - to + The question i have is the white/brown wire only has .6 volts to ground with vehicle running. do i need to use a different wire color? or hook an additional wire to the module to get - 12 volts from the white/brown? thank you

2015 Outlander Sport USA no parking lights

Wed, 02 Nov 2016 13:26:45 +0000

I have a 2015 Mitsubishi Sport USA standard key start. I installed the EVO One with no problems, except wiring diagram shows no connection to parking light for start indication and status. All other models either show using 2 diodes and connect to parking light left and right side, or using turn signal lamps but not this model. If this model uses the can bus to flash lamps, it does not work. Any special settings using flash manager? I see none listed.

Using guide # 16831 you can see no connection. Any help would be appreciated.

Location of light switch harness on 2009 Toyota Camry XLE

Sat, 23 Jan 2016 11:56:03 +0000

Im looking to find the location of the light switch harness on my 2009 toyota Camry so that I can hook up the parking lights to my remote start system. Is this harness on the front side or back side of the BCM? Is it located at the BCM at all? Thanks for your help.

-Keegan G

EVO-ONE-2005 Altima dont have a (-) parking light wire only a (+) one.

Sun, 20 Dec 2015 05:29:19 +0000

EVO ONE

2005 Altima

Reguar Install NO T harness.

2005 Altima dont have a (-) parking light wire only a (+) one.

According to Regular Instalation guide(Guide #16421), I need to connect the pink wire to a (-) Parking light wire but i only have a (+) Parking light wire.When we look at the T harness Instalation guide(Guide #18201), Its not even using the data and parking light wires.insted uses Auto Light shutdown Dr, Blue wire. Which one i should follow?