Questions & Answers - Recent questions tagged mazda-cx5

EVO ALL Mazda CX-5 Decryptor not working

Sun, 02 Feb 2025 14:50:35 +0000

I am installing a Fortin EVO ALL with THAT-MAZ1 THarness on a 2019 Mazda CX-5 PTS A/T following guide #66311. I had successfully performed steps 1-16, but repeating steps 1-12 as directed by step 17, it wouldn't complete the program, even after multiple attempts. Following previous answers in this forum, I was instructed to reset the EVO ALL and try to reprogram. Now, when I perform steps 1-12, I am getting a flashing red LED instead of the alternating Red and yellow. The Flashlink indicates Invalid Key Data. I have even attempted to program with a new module with the same flashing red LED. Any help would be greatly appreciated.

2013 CX-5 Cranks But Won't Start M/T

Mon, 02 Dec 2024 22:13:23 +0000

EVO-ONE. I have the THAR-ONE-MAZ3 harness. White cable for clutch bypass is connected. Not sure what's going on. I've tried changing the programmable output from 2.1 (default) to 2.2 (I think it should be this one?) and still no luck. It will try to crank for a few seconds, then shut off then tries again for a few seconds but won't start. Yellow jumper was cut when I received it, but it is currently twisted together until I verify what the issue is then I'll do a more rigid connection. I don't have the hood pin switch connected, my kit didn't come with it. Not sure if this is preventing it from starting or not. I have tried enabling and disabling A11 for this but still no luck with remote start. SN: 002B04 643579

Fuel level Evo start LTE showing 0% on 2017 CX-5

Tue, 15 Oct 2024 18:05:22 +0000

Hi, on the 2017 Mazda CX-5, the EVOStart LTE displays 0% in the app for the fuel level. Is there a fix for this or it’s not available for the vehicle?

2022 Mazda CX5 Evo One + THAR-ONE-MAZ3 + RF 942 kit unable to open hatch with 942 remote

Fri, 23 Aug 2024 11:51:36 +0000

Unable to open hatch with the 942 remote trunk release button. Everything else is working fine. Is there a solution?

2022 Mazda CX5 Automatic Transmission

EvoOne linkr LT2 app loses connection

Mon, 29 Jul 2024 19:50:22 +0000

Hi, I have EvoOne with Linkr LT2 installed on a 2019 Mazda cx-5 signature. Recently, the app would have trouble connecting to the car, it would be greyed out when trying to start engine and the icons would turn grey. It seems to happen intermittently,

CX5 horn does not go off when evo one alarm is tripped 2021 THAR-ONE-MAZ3

Sat, 10 Feb 2024 19:20:55 +0000

2021 Mazda CX5 evo one, the horn does not go off when alarm is tripped I used the THAR-ONE-MAZ3.

I chose car has oem alarm

Use evo one Remote start and alarm

I also reflashed and tried the same with car did not have oem alarm

Once alarm is activate I see and hear the clicking on the dash, but the horn does not sound

Ty

Install Guide #68261 Thar-One-Maz3 2017 Mazda CX-5 Automatic Push Start

Thu, 16 Nov 2023 09:28:01 +0000

I am following steps in Guide #68261.

1) As per large yellow "ATTENTION" warning, disconnected - terminal from battery.

2) Removed covers

3) Made the following connections: #4,#5,#6

7) Made the other required connections: Diagram on page 4 (Connect everything else)

6) Reconnect - battery terminal

Page 7 Step 1: Connect the 6-pin Main Harness

--already connected everything to Evo-One control at #7, however diagram show Evo-One control with NOTHING connected !

Are those connectors magically disconnected by themselves ? Maybe missing instructions ?

....disconnect battery - terminal ? .....disconnect all connections from Evo_One control ? ...reconnect - battery terminal ?

Evo One w/ Linkr LT2 - Transfer to New Car

Sun, 17 Sep 2023 13:22:12 +0000

The time has come to let the 2015 Honda Odyssey go, .

I have the Evo One with Linkr LT2 for several years now and works flawlessly. As a matter of fact, I have the same set-up in 2 of my other vehicles. GREAT PRODUCT!

Question, do I have to do a complete "hard" reset prior to installing the Evo One or can I use the flashlink to make the changes (new vehicle, key, etc) and update the Evo One. And would you know if I have to "reset" the Linkr LT2?

Any suggestions would greatly be appreciated.

FYI, I'm going from a 2015 Odyssey to a 2019 CX5 (I have the THAR-ONE-MAZ3 already on order).

2019 Mazda CX-5 (A/T & PTS) Alarm activating when remote starting (OEM keyfob/ 3xLock)

Mon, 04 Sep 2023 14:08:58 +0000

Sometimes when I try to activate remote start with my OEM key fob by pressing the lock button three times my car alarm will go off and then I press unlock and the car starts

Cx-5 without datakey failing remote starting

Tue, 20 Dec 2022 15:53:44 +0000

Hello,

I have a mazda cx-5 2016 with automatic transmission push to start.

but unfortunately my car doesn't have a DATAKEY pin in the CAN .

I'm using evo-all with RF kit (EVO RM942).

As per my understanding with DATAKEY not available I'm only left with the setup "Regular installation-1key programming" GUIDE#63601

I have made all the connectivity as per the guide and configured the module as per the guide...but never got the module to start my car...I got it only to lock and unlock my car using the RF remote or original remote.

when I try to start my car the evo-all module just starts clicking multiple time but the car never starts.

below is a link of a video for the behavior of EVO-ALL when I attemp to remote start the car.

https://www.veed.io/view/5b07e914-1a3c-49d4-ab0c-5372c7b1c617?sharingWidget=true&panel=share

Any idea or suggestions please?

Thanks in avance.

Regards,

2016 CX-5 AUTO, PRESS AND HOLD PROGRAMMING BUTTON , EVO ONE ONLY BLINKS RED DOES NOT ALTERNATE BLUE RED YELLOW

Sun, 26 Jun 2022 22:27:24 +0000

Hello, Installing Evo one with MAZ 3 'T' Harness in a 2016 CX-5 (push start automatic ), only get a blinking red light for first step programming, not alternating blue, red, yellow. options were set and saved ok with flash link updater.

.......thinking maybe a bad 'T' harness ?

Please advise if possible

Thanks

Ken

Cx-5 2016 alarm

Thu, 11 Nov 2021 07:16:09 +0000

After istallation of evo-one in mazda cx-5 2016, qhen remote start de vehicule the alarm oem start. Wired with thar-one-maz3

2018 Mazda CX-5 evo one Thar Maz3 windows dont automatic go up or down

Sat, 04 Sep 2021 18:00:01 +0000

I installed EVO ONE with Thar One Maz3 harness in 2018 Mazda CX-5. Before install my windows would go up and down automaticly Just hit the button and let go. Now after install I have to hold the button until they are either up or down. How do i fix this?

Software Incompatibility with Remote Function Actuation

Sun, 14 Mar 2021 16:45:43 +0000

I have installed the EVO-ONE-942 with THAR-ONE-MAZ3 on my 2016 Mazda CX5 Automatic Push Start, and when scanning the vehicle with Thinkcar I get a DTC in EPS module, code U0338:00-08 (Software incompatibility with remote function actuation).

After clearing all code, it comes back again ...

Also, I've noticed the trunk open on the remote opens it half way, meaning it still cannot be actually opened until you unlock the car. Is there a way to disable trunk open as it doesn't work right?

Another weirs "issue" I found, when the car is unlocked with Fortin remote, then locked with "OEM" remote, when you check status with Fortin remote, it will say unlocked even though it's locked. Then when you lock with Fortin remote, it will report the status correctly.

Some quick post-install questions ...

Sun, 14 Mar 2021 00:14:56 +0000

I have just installed the EVO-ONE-942 with THAR-ONE-MAZ3 on my 2016 Mazda CX5 Automatic Push Start.
Everything seems to work just fine, but I had a couple of questions ...

When I did the programming with Flashlink manger I went throigh the "wizard" step by step, and picked
that my car already has an OEM Alarm system (I verified by rolling window down, locking, then unlocking,
and it sounded the alarm). I chose not to use the OEM remote for starting, just the Fortin RF one ...
I also did not install the Valet switch, or the Hood pin.

Question, since it seems to work I am assuming that I didn't need to enter manual options to fine tune anything?

Also, when I went through the programming, would I automatically get a firmware update or did I have to do
that step manually and I missed it? My unit was made at the end of 2020 so I assume it's fairly up to date?

Thanks in advance!

red flashing instead of red and yellow flashing?

Sun, 10 Jan 2021 06:06:33 +0000

Mazda cx-5 2018

Evo all guide # 66311

on step 13 I have an only red light flashing once every second and did not stop!!

I tried and read different solution founded here, but it ends with the same red flashing

all wires connected correctly

EVO-ONE - failed MA inspection after install 19 Mazda cx-5

Tue, 15 Dec 2020 18:51:39 +0000

Went for a state inspection a few days after install failed because weak battery that was my fault a light was left on in the cabin, went back a couple hundred miles later and massachusetts state inspection lists certain systems as not ready. Anyone else seen this caused by the evo install? Could I temporarily remove the evo and the harness for the purpose of the inspection and put it back without damage?

Cannot unlock passenger doors after remote start, EVO-ONE in a 2018 CX-5

Sat, 28 Mar 2020 14:03:08 +0000

2018 Mazda CX-5 with the EVO-ONE and THAR-ONE-MAZ3. The remote start works fine, but I haven't been able to find a combination of settings where I can unlock the passenger door after a remote start (with key or button on door handle), without setting the system to just unlock all of the doors all of the time. There is a setting that specifically mentions allowing this function, and it doesnt seem to do anything expect for some reason adding a honk to confirm the start up sequence is complete. Firmware for bypass/remote start are both up to date as of today. When I don't trigger a remote start and unlock the car with the fob/door handle, the car unlocks the driver door first and passenger doors second as normal.

2015 Mazda CX-5 - Evo One and Thar-one-maz3 Turn Signals not working

Sat, 01 Feb 2020 14:03:22 +0000

EVO-ONE and THAR-ONE-MAZ3 installed and remote starts with no issue.

When unlocking the vehicle, the turn signals blink but will not turn on when activating the hazards or using the turn signals. Additionally, the heater will turn on, but the fan speed can not be adjusted.

These issues persist regardless of being remote started or started as normal. I'm not sure if it matters, but the current remote start procedure is set to lock-unlock-lock.

Rear Defrost & Heated Steering wheel .

Sat, 25 Jan 2020 09:03:33 +0000

Any guide available to connect rear defroster steering wheel heated functions on 2019 CX-5 mazda for evo-one?

2014 CX-5 EVO one THAR MAZ3 used to work ok but now not unlocking and start button blinks amber

Mon, 30 Dec 2019 10:29:54 +0000

Installed a Evo one with THAT MAZ3 harness and worked fine for a while. Occasionally would have issue with not doing a standard door unlock from remote. Now never unlocks with standard remote, have to use physical key, and will not push to start, have to hold key up next to button. Push button in car blinks amber. Have changed out key battery many times but no better.

Evo One - Unable to start decryptor programming procedure

Sun, 14 Jul 2019 21:09:25 +0000

Steps 1, 2 and 3 of Guide 68261 work exactly as described, however when executing step 4, the system does not start and displays a message of "Key fob battery low. Hold key close to start button". This is normally the message you get when the key is not close enough to the car when trying to start.

I am wondering if I configured something incorrectly on the Evo One? Pictures of the programming light and message on the dash below.

https://imgur.com/a/Dpu7sdd

Start stop unit connector 2 wires don’t match to the guide

Mon, 26 Nov 2018 13:01:18 +0000

Hi,

mazda cx5 2014 keyless entry push to star automatic.

In the guide it says that I should splice Lt.blue/black wire from T harness to the 8th pin black/white wire of the 32 pin connector 2 from start stop unit.

The issue is that I have no any wire in the 8th pin of the connector2.

Could you please let me know where to connect Lt.blue/black wire?

thanks

Must the firmware on evo one be updated to the guide recommended prior to install even if the current firmware is newer?

Fri, 16 Nov 2018 13:19:53 +0000

2017 cx5 Push to start automatic. First install, with T-harness

In the install guide it states the minimum hardware ver 3. Is this refering to the Starter or EVO-ALL hardware?

Fri, 15 Dec 2017 23:12:56 +0000

I'm looking for some clarification.

In the installation guide for a Mazda CX5, Evo-one + Thar-one-Maz3 Guide # 68261. Its states Hardware Verison: 3 Minimum.

On that back of my evo-one there is mulitple hardware versions listed.

Starter 7.1.21
EVO-ALL 2.4.18
Date: 10/2017

I'm confused, the starter hardware version is above ver 3, but the evo-all is below 3. In the guide which version is it refering too? Since the unit has a recent build date (10/2017) i would think that it would be the lastest and greatest hardware version, Right?? Why would fortin be still manufacturing old versions?

thanks in advance!

Which remote start is good for me?

Fri, 20 Oct 2017 13:19:22 +0000

Hi,
I am a newbie in the remote start area, I do not understand a lot of things.

I am looking for a simple remote start solution using my original for my 2014 Mazda CX-5 automatic.

The site gives me 2 answers, EVO-ONE and EVO- ALL for double price. I do not understand what are the differences
- What does mean T-Harness available? Is it necessary or optional? For what?

- Flash Link updater? What is? Ok, I know what is firmware updater, but is this required or optional?

- What is Regular installation and Standalone installation?

- What is Take over? Is it something hardware or just a settings?

EVO-MAZT-1 Takeover in 2016.5 CX-5

Sun, 01 Jan 2017 11:24:10 +0000

Can I wrap a key so that the engine does not shut off when a door is opened? If so, does this defeat any theft deterrent?

Unit is EVO-All with firmware 71.38. Installation is T-harness plus RF-ALL 642W. Vehicle is 2016.5 Mazda CX-5 Automatic, Push-to-Start.

mazda cx-5 doesnt remote start

Wed, 30 Mar 2016 16:00:54 +0000

installed an evo-one in a cx-5 everything went good done the programmation 1-12 went good done it a second time and i only get a yellow light not the usual red and blue .tried to progarm the blue led and it start to alternate red-yellow-blue then blinks blue like when you program with one key fob.tried to remote start without success park light lights up when trying to start and then turn off and doesnt blink only thing that blinks is the blue led on the rf antenna as it blinks 4 times

Evo all on CX-5

Sat, 09 May 2015 07:15:31 +0000

1. Do I have to connect wires for parking lights? I can't find 6 pin connector near the handle. 2. Power: I installed the remote starter only unit woth evo-all. I connected data cable but did not get any power. So I cut the red and black wire and hard connected them. Is that OK for having a Remote starter? How are the two units going to communicate each other? 3. Programming : the instruction told me to press and release the programming button 5 times after I get solid blue and red lights. I did that but those two lights are not flashing at all. They just remain solid whatever I do.

Door Pin Image/Location for 2013 Mazda CX5 to prevent headlight drain the battery.

Mon, 23 Feb 2015 19:16:45 +0000

Door Pin Image/Location for 2013 Mazda CX5 to prevent headlight drain the battery. After the remote start expired, auto headlight won't turn off itself, unitl i come out to the car and shut it off. Please assist.

Which wire from Evo All that would hook up to the suv? thanks.

Mazda CX-5 2016 et evo-all v.71.23

Mon, 23 Feb 2015 16:15:34 +0000

Est-ce que la version du evo-all 71.23 est compatible avec la CX-5 2016? J`ai essy

Can I put in EVO-ALL plus (only) Drone in 2015 Mazda CX-5?

Sun, 22 Feb 2015 11:19:05 +0000

Right now nothing is installed in my 2015 Mazda CX-5. I'd like to install the EVO-ALL to use my factory remote to start my vehicle. On top of that I'd like to install a smartphone option like the Drone to remote start my vehicle. I do NOT want to have more installed than this. How/is this possible?

Wiring diagram CX5 Stand Alone

Wed, 28 Jan 2015 16:07:11 +0000

Hey I know this might be rookie questions but, I recently purchased the Evo All for my mazda CX5.

I will be installing it Stand Alone.

Looking at page 3 of 13, I am a bit confused with the wiring of D1 and D3. You say to cut the wire from slot 3 on parking connector, then to attach D1 to wire coming from car harness not the connector, is that right or am i reading it wrong?

Is D3 connected?

thanks

Does the Evo-all now support takeover not requiring the car to be shut down?

Mon, 05 Jan 2015 10:07:46 +0000

Looking at the EVO-ALL guide it mentioned that push to start control is supported on the Cx-5. Does this mean that the vehicle will not turn off when the door is unlocked?

2015 cx5 won't start and brake lghts don't activate.

Sun, 04 Jan 2015 22:26:39 +0000

Followed evo all pts instructions revision 20141224. bypass programmed properly, but when you press the remote start button vehicle doesn't crank. the ignition lights up, but the brake lights don't light up. with key inside of vehicle it will also not crank over. checked all the wiring and it's wired properly. if you start the vehicle using the pts button and fob inside of vehicle and have the remote start take over the brake works to deactivate the remote start and the footbrake is connected to the evo all not the brake switch. flashed to update 71.22 firmware. do you have any ideas on the problem.

2014 CX-5 PTS - remote starter - no key required?

Sun, 28 Dec 2014 00:16:09 +0000

Can you please confirm that with the newly released evo-all, I can install a remote starter on my 2014 Mazda CX-5 GT PTS without losing a key now? Also, I want it so that when starting my car, after opening the door, the engine does not automatically shut off. Is this possible now? I know that this was a problem in the past that was only resolved by having a physical key hidden in the car.

Probl

Mon, 07 Apr 2014 14:18:13 +0000

Installer d

mazda cx-5 2014 pts

Thu, 13 Feb 2014 15:13:08 +0000

le demarreur crank mes pas asser longtemp pour demarrer le moteur

Comment contourner l'alarme sur Mazda CX-5 2014?

Tue, 12 Nov 2013 09:38:17 +0000

Quand on d