Questions & Answers - Recent questions tagged mycar

Mycar2 with rfkit 411

Fri, 24 Nov 2023 18:33:10 +0000

I recently installed mycar2 app with Fortin e400 module. The app is working fine along with the module. However is it possible to install RFkit 411 or 441 to the same system. Is it either my car2 or rf kit?

2010 Lexus RX 350 – EVO-ALL Stand Alone with ASCL6 CARLINK: Remote Start Not Working ( NO IGNITION, NO CRANK)

Thu, 26 Oct 2023 14:59:43 +0000

Issue: Remote start does not work when initiating the remote start command via factory remote (3X lock) and/or CARLINK App.

A few things that I noticed when trying to remote start the car:

The transmitter and CARLINK app are communicating with the EVO-ALL - when the remote start is initiated, the blue LED on the EVO flashes once and a solid red light illuminates after. During this time, no lights on the cluster/dash turns on and there is no crank.
The EVO attempts this process again with the same results. After the second failed attempt, the red LED on the module and the car’s parking lights flashed 3 times.
Next, I tried remote starting the vehicle using the idle mode.
- I started the car by stepping on the foot brake and pushing the START/STOP button.
- Once the car was running, I activated the remote start with the CARLINK app.
- The remote start count-down timer appeared on the CARLINK app which tells me that the command was sent, and the module is in the remote start mode.
- I stepped out of the vehicle and the dash screen notified me there was no key (car remained idling)
- CARLINK app still showed the count-down timer for the run time.
- I deactivated the remote start using the CARLINK app and the vehicle turned off.

I also checked to see if all the other commands were working properly by using the CARLINK app.

Lock/unlock doors – good.
Open/close back trunk/door – good
Parking lights – good
Vehicle lock and unlock status - good, shows on the app when the doors are locked or unlocked.
Battery voltage shows on app, (13V)

I’ve doubled and TRIPLE checked the wiring, making sure they were terminated as shown in the installation guide (GUIDE # 77041) and that all connections were secured.

I don’t know if I am having issues with the installation or programing. I tried resetting the evo and re-flashing it and also down-grading the firmware to 79.66 to match the firmware on the guide. I think I might have tried a different firmware version as well (in between 79.70 and 79.66) with no luck. I eventually got locked out of the EVO-ALL because the flash limit was reached. I ended up ordering a second EVO-ALL to started from scratch again and I encountered the same problem.

I confirmed that the car does not have a factory remote starter by pressing the factory remote Lock button 2X and holding it after; the car did not start. Furthermore, I removed the glove box to check if a factory remote start was present, and as far as I can tell, I did not see one. The location of the factory remote starter was referenced from an Automotive Data Solutions Inc. (FLCAN and ALCA TL2) installation guide. If you have more details about where else this might be, please let me know and I can check again.

Please HELP! What should I check next?

Here are some details about the EVO-All that is currently installed.

Manf Date: 04/2023
SN: 001A07499141
Firmware Flashed: 79.70
Hardware Inside 7.0
Setup Configuration
- *** SETTING PROTECTION = OFF
- A1-A11 = ON
- A12-A14 = OFF
- B1-B3 = OFF
- C1 = ON
- D1 = ON
  - D1.8 = ON
  - D1.10 = ON
  - All other D1.X = OFF
  - D2-D5 = OFF (Guide shows D4, Hybrid Mode- do I need to turn this on?)
- D6 = ON
- D7 = OFF
- SPECIAL FUNC = ALL OFF
- DATALINK PROTOCOLS = ALL OFF
- G = ALL OFF
- H SUPPORTED RF KITS = ON
- H2 = ON
Wire Connection (connected according to diagram):
- A8: Not connected - vehicle is equipped with factory hood pin so that status is provided via can bus, correct?

2014 Audi RS7 EVO ONE with Carlink ASCL6 4G

Tue, 10 Oct 2023 23:35:58 +0000

What remote start firmware should I used if I am adding a ascl6 carlink to my Evo-One?

Mycar not working properly with evo

Mon, 29 May 2023 16:10:18 +0000

Mycar Lt2 won't work properly on evo one I believe it's paired as I can send commands,shows gps,battery. So problem is if I ready car then later send start signal it will start run a few seconds then shut down and unready vehicle also when I send lock/unlock it sends it three times on either senario as well as it always shows green unlock doors in the middle no matter what state car is in volt and gps seem to work okay I'm trying to get this module up and running please

Alarm input detection myCar

Sun, 11 Dec 2022 00:42:45 +0000

Does anyone know how many pulse the alarm input detection on mycar need to see before it notify the app? Also is there anyway for me to use any aux option myxar have with an evo-all installed in 2014 camry pts. Thank you so much

Switching from Evo-start2 to Mycar

Wed, 30 Nov 2022 18:25:15 +0000

I currently have EVO-Start2 installed in my car and want to switch to Mycar due to relocating out of Ontario to British Columbia. Is it a simple plug and play, or will the Evo unit need to be reprogrammed for the new telematics?

Linkr Yellow Wire

Tue, 12 Jul 2022 11:19:02 +0000

Would I be able to connect the yellow wire from the LINKR-LT2 module harness to my Evo-all instead of the horn if so which wire would it connect to?

Unit is set as standalone alarm / remote start

Thank you in advance!

FAQ: Programming CARLINK, ASCL6, LINKR, MYCAR

Mon, 17 Jan 2022 10:06:40 +0000

To program your carlink,

make sure to follow their instructions on how to connect it to the EVO-ALL or EVO-ONE using their own HRN-LLRS-01 harness
setup the app for fortin
follow programming in car

Here is a copy of their guide. Please read attentively every step of programming since their is setup in the app you must first do. https://fortin.ca/download/64631/ascl6-install-guide-64631.pdf

EVO-ONE Programming

Following the RED LED on the BACK of the unit, not the one on top.

Igniton ON-OFF-ON (red led on evo will turn on solid)
Hit brake 4 times (red led will flash on each brake press)
At this point wait 10 seconds then shut off the car.

EVO-ALL Programming

Please first try the EVO-ONE. It was added to the EVO-ALL firmwares.

Otherwise, this older method is still functional.

Disconnect the 20-pin connector
Disconnect the 4-pin black connector
Press and Hold programming while inserting 4 pin connector.
Release when the LEDs are BLUE and RED
Press and HOLD programming button, wait until the BLUE and RED LEDs turn and then BACK ON. Release when they turn back ON.
Plug in 20-pin connector
Turn ignition ON, all three LEDS will turn ON
Wait 10 seconds, then turn off ignition.

Unable to program MyCar telematics module to EVO-ALL

Wed, 17 Nov 2021 19:41:54 +0000

When trying to learn MyCar telematics module to the EVO-ALL, at the point after switching the ignition ON when the RED & BLUE LED's are supposed to flash, they never do. I have waited upwards of 10 minutes, but they never flash.

My MyCar app reads the GPS position of the car but Start/Stop and Lock/Unlock does not work. The telematics module LED's show that the module is connected to both GPS and Cellular.

The OEM remote start works as it should with Lock/Lock/Lock.

2021 Toyota Corolla, Push Start, Automatic with T-Harness. EVO Serial N.: 001A07 220406

Any suggestions?

I have Mycar app starter with idatastart module in jetta 2018, want to switch keyless evo all module

Mon, 25 Oct 2021 22:57:44 +0000

I ave got installed Mycar app starter which has idatastart module, in which we need to put one key for bypass.

i lost one key and now i want to replace idatastart module with evoall for key less starter.
In vw jetta 2018 key start

Q1. Can i use myapp with evo all?

Q2. Are Evoall,TD VW and flash updater products all i meed to buy ? Do i need to biy anything else? Like T harness ( Because there already one harness put with my car starter)

Q3. What all any additional tools do i required?

evo-all, mycarapp, vwJetta2018 keystart

Evo one does not enter program mode to program telematics unit.

Mon, 11 Oct 2021 21:49:56 +0000

2020 rdx push to start. Nothing happens after holding the button for 5 sec with ignition on.

Programming EVO-ONE to use MyCar telematics and RFK441

Sun, 28 Mar 2021 11:02:39 +0000

Is it possible to have the MyCar and the RFK441 coexist? It seems the answer is no. I can have both the MyCar and the RFK441 programmed to the EVO-ONE. And inidivually they will work and operate the EVO-ONE. But if I plug in the RFK441 into the harness of the MyCar to have both of them attached to the EVO-ONE, only the RFK441 controls the EVO-ONE.

If it is possible, what steps can be taken to make this happen. Or do I need a different remote kit for this to work?

Thank you.

Jim

Evo all & ascl6 program issue

Sat, 20 Mar 2021 20:16:58 +0000

2014 ram 1500 (standard key start) after successful programming, vehicle can be remote started by 3x lock only....H2 - fortin 2 is selected on in flashlink setting, ascl6 app protocol is set to fortin, RFA2A adaptor is connected but still no luck, both red and green led on ascl6 are on solid, been trying to get the evo all to pair with ascl6 with no success.

evo all led lights are stuck at step 8, will not go to step 9

1 - Disconnect the Black 4 pin power connector from the Evo-All.

2 - Press and Hold the Programming button on the Evo-All while plugging back the Black 4 pin connector.

3 - The LED’s on the Evo-All will begin to cycle. Keep pressing the programming button until the RED and BLUE LED’s are On.

4 - Release the programming button.

5 - Press and Hold the programming button again for 5 seconds. The BLUE and RED LED’s will blink once.

6 - Release the programming button.

7 - Cycle the ignition to the ON position.

8 - The RED, YELLOW and BLUE LED’s will be ON.

9 - Seconds later the RED and BLUE LED’s will blink once to confirm that the MyCar ID has been learned to the Evo-All.

10 - Cycle the vehicle’s ignition to the OFF position to Exit EVO-ALL programming.

Does evo all have to be setup for 3x lock for mycar module to work?

Wed, 27 Jan 2021 07:52:48 +0000

Looking to get Mycar module. I have a 2019 explorer with evo all standalone fort3 harness. I set it up using lock/unlock/lock to remote start. Mycar directions is showing 3x lock for install. Will it work using my configuration? If I have to, I will disable horn honk with lock press with forscan, but I would rather not if possible.

ASCL6 And evo one. The door unlock on it own after about a min

Thu, 10 Dec 2020 13:34:06 +0000

This happened only when I used the CL6 car link app to start my vehicle. The car unlocked, engine start, and relock the doors. But after about 1 minute and 26 second, the vehicle unlock without me touching anything. Please help

Not running for 30 minutes

Tue, 20 Oct 2020 20:05:46 +0000

I have the fortin evo and the flash shows it's at 30 min on my diesel. When I remote start it with mycar, it will start at 30 and immediately drop to under 15 min. I let the truck run and it shut off after 15 min. What's wrong?

Evo-one with MyCar Telematics & fortin RF kit

Sun, 17 May 2020 18:21:30 +0000

I have evo one with MyCar telematics plugged into the (4-PIN) DATA-LINK ANTENNA with the MyCar HRN-LLRS-01.

I also want to add the fortin RKF411 to the evo one but the port is taken up by the telematics. I tried plugging the fortin rf kit antenna harness to the the other female connector of the HRN-LLRS-01 and the rf kit works but the telematics doesn't. Unplugged the rf kit and the telematic works again. Is there a way for me to use the rf kit on another port? Thank you

2019 F150 install issue with Fortin EvoAll install and MyCar Controller

Sun, 26 Jan 2020 19:36:51 +0000

7- The RED, YELLOW & BLUE LED’s will be ON.
8- At that same moment the RED & BLUE LED’s will blink once to confirm that the MyCar ID has been learned to the Evo-All.

I am installing the MyCar module and make it all the way to step 8 but the lights never blink to confirm. What might be another step not included in the install guide?

2016 Tacoma Automatic - Push button - EVO-ONE w. MYCAR Telematics

Thu, 16 Jan 2020 22:40:19 +0000

Hi,

I had succesfully installed the EVO-ONE and using factory fob for remote start; The MyCar unit arrived with instructions. install-guide-64631. Everything works per instructions until step 8; when I press brake and release and then turn off, I get several blinks of lights and Evo unit, not the "Once" that is expected.

Mycar is online and I can see the unit, car voltage etc. It will just not learn to the EVO-ONE... I cannot seem to get past this step.

STEP 8. LEARN THE TELEMATICS DEVICE TO THE EVO-ONE

In order to communicate with the remote starter, the MyCar must be learned to the EVO-ONE.

1 - Cycle the ignition to the ON position.

2 - The YELLOW LED on top of the EVO-ONE should come ON.

3 - Press and Hold the EVO-ONE push button for 5 seconds.

4 - The parking lights and the RED LED on the side of the EVO-ONE will turn ON.

5 - Release the push button.

6 - Press and Release the push button 5x times. Everytime the push button is pressed the parking lights and the RED Led on the side of the EVO-ONE will blink.

7 - Then Press and Release the Brake pedal.

8 - Seconds later the RED LED on the side of the EVO-ONE will blink once to confirm that the MyCar ID has been learned to the EVO-ONE.

MyCar Programming without valet switch

Sun, 27 Oct 2019 15:40:30 +0000

How do I enter programming mode to get the MyCar module programmed without a valet switch? I have a 2013 Toyota Tundra and installed the Evo One in 2015. Everything works fine. I'm unable to get the Evo One into programming mode to accept the MyCar Telematics module (because I never had a valet switch). Is there any other way to get into programming mode without a valet switch?

MyCar Programming without valet switch

Sun, 27 Oct 2019 15:38:27 +0000

Will any of these products work with OEM remote starter already installed

Fri, 25 Oct 2019 15:14:34 +0000

Hi,

I have a 14 Ram 1500, which already has a factory installed remote starter. I'm looking to switch over to Fortin, and use a MyCar RFLink. Can you suggest which product/products i could use to make this work.

Thanks!

Jesse

EVO One and MyCar LinkrLT successfully start then immediately stop

Sun, 20 Oct 2019 15:52:45 +0000

Hi, all. I installed a Fortin EVO One about a year ago in my 2015 Nissan Rogue Select, with the applicable t-harness kit. Just to give a bit of background, I ordered my Evo pre-programmed from a reputable seller on eBay along with a DroneMobile. The Drone device was always buggy and unreliable, so I replaced it not long after with the RF642W remotes and a MyCar (Yes, I did buy the flashlink and reprogram the EVO one). When I originally installed them I was unaware I needed a diode for them both to work, so I just got around to doing that recently.

My remotes have worked flawlessly from the get go, I just installed the diode today and the MyCar now paritally works. It can lock and unlock the doors, and when I send a remote start command the vehicle will lock and start, however it shuts off in about 5 seconds or less. The remotes however still work flawlessly, which perplexes me a bit. From what I've seen this normally indicates the remote start doesn't have proper engine RPM data, but I'm curious as to why the remotes would work normally and the MyCar doesn't

Is there any difference in installation (wiring) with evo mystart than regular installation?

Thu, 22 Aug 2019 07:59:15 +0000

Hi, my service advisor came up to me asking if I could install the evo mystart remote and I told him I can try but never done one. I will be installing on a recent Kia Sportage (assuming its between 2017-2020). Not sure if its push to start or regular key but is there any difference of installing (wiring) and wheres the procedure to install the mystart?

Will MyCar report alarm triggers from EvoAll Alarm?

Mon, 03 Jun 2019 17:40:32 +0000

2016 Yukon. EvoAll standalone with alarm. Want to know if connected MyCar will provide alarm trigger reports.

mycar programming

Thu, 14 Feb 2019 16:00:10 +0000

When going through the pairing procedure of a mycar (ascl6, link6, teleconnect, carlink) to an EVO-ALL or EVO-ONE, send a Lock command from the APP instead of waiting for their autolearn at the last step of programming.

mycar telematic programming- evo one

Sat, 05 Jan 2019 21:19:33 +0000

hello, i am trying to learn the mycar module to the evo one (2016 subaru impreza firmware 1.24). the insructions say to hold down the programming button for 5 seconds, but nothing happens when holding it down i tried even longer but got nothing. any ideas?

MyCar Telematics starts then turns off after a few seconds

Thu, 27 Dec 2018 17:57:05 +0000

Vehicle: 2011 Toyota Corolla S (G-Key), manufactured in CAN.

Evo-One w/T-harness installed and working properly using OEM remote (3x lock to start).

When trying to start vehicle via the MyCar app, the engine will start and as soon as the doors auto lock the engine will shut off.

I have installed the MyCar Controls telematics unit based on the guide here: http://cdn02.fortin.ca/download/64631/autolink-install-guide-64631.pdf#page9

I used the HRN-LLRS-01 connector as instructed.

“Fortin 2” selected in RF section of configuration tab in FlashLink Manager.

MyCar Controls app Device Protocol: Fortin

Please help!

Where is RF Option

Sat, 15 Dec 2018 09:58:01 +0000

There is no option to enable RF kits in the flash updater tool. I am trying to add a MYCAR, Autolink module.

Some questions regarding +12V connection, fuse size, etc. ('14 A6)

Sun, 25 Nov 2018 20:19:53 +0000

Just a couple of questions on a '14 A6 install (EVO ONE + MyCar smartphone).

The two +12V wires (E3 & D3) are to be connected at the OBD-II harness. Since this is a faily low current application so I'm wondering what the appropriate size fuse should be. Nothing in the quide regarding fuse size. In a few of the low-current EVO-ALL installs they specify a 5A fuse, would that be suitable here too?

On the same topic, I imagine the OBD-II wires would likely be thin-gauge, (EDIT: +12V looks like 18gauge from the guide photo)... It looks like the E3 wire is 14g. Since this is a low-current application, I'd like to step it down to a smaller gauge so it's not such a bulky connection at the OBD-II +12v wire. How small could I adequetly go on that?

One last question: Does the EVO-ONE provide power & ground to the MyCar smartphone addon through the data connector? They have optional power & ground wires for modules that don't provide power... Just want to get an idea before going into the install.

MyCar app not showing runtime and only starts less than half time.

Wed, 17 Oct 2018 22:06:21 +0000

2014 RAV4. EVO All. Crimestopper Cool Start RS00-G5. T-harness. I finally got this setup to work with the OEM black H-key remote with 3X Lock press. I still don’t get a parking light conformation, and the doors won’t unlock, via automatically or with the fob. The MyCar app shows battery and signal levels, and GPS location. No runtime, or remote start conformation. It only seems to start after I open the map and it is located. Then it will start, shutdown and locks require the same. I do have a Fortin flashing tool, and don’t know what else to do.

Please help?!?!

Thank you!

EVO-One set for 30 min runtime but shutdown after 15 min

Sat, 13 Oct 2018 11:10:06 +0000

EVO-One set for 30 min runtime only running for 15 min MYcar shows 30 min runtime when starting truck just runs for 15 min shutdown howerver app is still counting down

Using Evo-One with MyCar Module on 2018 Toyota Tundra

Mon, 27 Aug 2018 19:13:24 +0000

Trying to get MyCar module to work with an Evo-One that works as expected with OEM key fob. Connect it Evo-one and program. Appears to program correctly, proper light flash after hold then pushing valet button 5 times with key on, hit brake and get confirmation. MyCar app shows where my car is on map, voltage of car and cell signal. It will not start car of do other functions. Fortin Tech says Evo-one should work with thos out of the box. cAN NOT FIND ANYWHERE IN fortan software to program cellular module.