Questions & Answers - Recent questions tagged nissan-murano

Too many keys issued while programming evo-all 2017 Nissan Murano

Wed, 20 Feb 2019 09:45:16 +0000

So while attempting to do the Dcryptor process for my 2017 Nissan Murano using the EVO-All and T-Harness kit, the process wouldn't complete, instead if would say there was a problem with the USB connection. So I attempted to do the Step 1 of programming again but now the Dcryptor process is saying that too many keys have been issued for my vehicle now. So, how do I go about resetting this error so I can start over again. Can I reset it by myself using the flashlink? Any help is greatly appreciated!

Do I need to Turn On D7 Rap Disable For door pin connection.?? or just leave it off.

Wed, 19 Dec 2018 21:02:51 +0000

Is D7 Rap Disable, Need to trun ON for rap shutdown. on 2014 nissan murano

2014 Murano - What is the Door Pin connection for?

Sun, 14 Oct 2018 15:31:05 +0000

I have installed the FORTIN EVO-ALL with THAR-NIS1 in my 2014 Murano. The only connection I was not able to make was the Door Pin connection to the Pin on the BCM connector. I found the BCM, but it's on a board that is too tight to access even after removing the instrucment cluster, etc. Can I leave it disconnected and what will happen as a result?

2010 Nissan Murano - Remote Start Not Working Unless Key is in the Car

Sat, 06 Jan 2018 15:31:16 +0000

I installed the EVO NIST-1 into a 2010 Nissan Murano with the Push-to-Start Button. I used the T-harness and the unit appears to have programmed properly. The car will remote start as long as the key is in the car. If the key isn't in the car it will not remote start. When I push the lock button three times, the lights and brake lights flash the same as if it the key were in the car, but the car doesn't start and the indicator on the dash says "No Key".

can i plug the t harness to the push button?

Sun, 03 Dec 2017 13:22:07 +0000

i followed all the instructions except the brown wire it goes to the push button because i`m confused between connect the t harness or the brown wire. i programmed the evo one and when i click the lock button three times the brake lights turn on but the car won`t turn on because i don`t which one i have to connect to the push button ( the brown wire or the t harness )

Is there a T-Harness for 2017 Nissan Murano Push button start?

Mon, 27 Nov 2017 21:13:08 +0000

Is there a T-Harness available for 2017 Nissan Murano's with push button start?

The remote start will come on and not crank. It says brake on the dash.

Tue, 10 Jan 2017 00:11:45 +0000

The program went well

2012 nissan murano wont start after evo all install

Sat, 07 Jan 2017 16:24:38 +0000

hello i have a 2012 nissan murano i just installed the evo all with the nist1 harness. for the oem 3x lock. the wiring and programing was shaky at first but i started over and got it right the second time. I can see that the module is responding to the oem remote (blue light flashes when lock button is hit) but the car never starts. one thing that i noticed is that the red light never come on after the 3x lock nor do the brake lights.

nissan pts standalone and smart start

Tue, 14 Apr 2015 14:31:55 +0000

So im installing a smart start with a evo all stand alone in a 2013 murano. I have 2 questions. 1: do i have to hook up the lock out outs from the smart start to the evo then pin the evo lock wires to the bcm? 2: will the evo pop the liftgate through data when using the smart start??

Murano - Multiple Key Bypass Programming

Sun, 22 Feb 2015 13:59:06 +0000

I have successfully programed one of mine OEM key (push-to-start) for a remote start in my 2011 Murano, however I just noticed that my second OEM key does not remote start the car. I

Nissan murano standalone with harness 2013

Tue, 20 Jan 2015 16:25:27 +0000

Hi there, at Nissan murano New guide its mentioned that lock and unlock wires are optional . what does it means? If I dnt connect them what features will not operate in the Evo all? External outputs for loco and unlock? Which options do you recommend to use after flashing the module ? Thanx

EVO- All for 2009 Nissan-Murano

Mon, 22 Dec 2014 20:45:30 +0000

What are the lock/unlock, start/stop external control wiring for? Does that need to be hooked up in order to lock/unlock the vehicle with the keyless remote? Also is there a way to avoid having to connect to the BCM connector for the lock/unlock? Can I splice in somewhere else instead of removing the instrument cluster? All I want to be able to do is remote start the car with the factory remote and lock/unlock the car with the same remote. Thanks.

2011 Nissan Murano - Heated steering wheel

Sun, 14 Dec 2014 20:59:36 +0000

Is that a way to program the module to enable the Heated steering wheel button after the car started?

Thanks.

Murano shuts down

Mon, 25 Aug 2014 22:42:48 +0000

I've installed 2 remote starters in 14 Murano's and both have the same problem. Once in a while the vehicle starts and shuts down right away. If you start it again it starts fine.

Firmware is 72.14

UltraStart 3295 2 way remote starter

Nissan T-harness used

Option B2 turned on

2014 Nissan Murano not starting

Mon, 11 Aug 2014 04:22:07 +0000

I have installed an Ultra Start with an Evo-All using a T-harness.

The vehicle will not start unless I reach in and press the brake pedal. I have the options turned on for push button start and fortin d2d and oem remote monitoring(b2,c1,d2, d6, f1) Door locks function correctly.

Firmware is 72.14

Any help would be great,

Thanks

Hardwire white 20-pin connector for THAR-NIS1?

Thu, 13 Mar 2014 15:55:49 +0000

I'm looking at the THAR-NIS1 Install Guide for stand alone mode and I am wondering if I need to hardwire anything for the white 20 pin connector? To me it looks as though I need to, but maybe not because of the T-Harness? Can you give me any insight?

To me it looks like I need to hardwire -
Ingnition
Lock - could I grab right from door?
Unlock - could I grab right from door?
Parking Light OUT - Where is this connecting to? Diagram says out but don't see a connection.
Driver Door-Pin - could I grab right from door?
White/Black to Push-to-start

Also what is the Lt. Blue and the Lt. Blue/Black wires going to the 20-pin connector?

I'll be using this for a 2011 Nissan Murano.

nissan murano 2013 RUS MAKE (or made in Russia) and evo-all and remote starter/alarm system

Tue, 04 Mar 2014 23:55:02 +0000

hello.

all that i have now:

- nissan murano push- to- start (year of manufacturing - 2013), made in russia . they say that american and european muranos have a differences;

- alarm system and remote starter (all in one), not installed yet (it has data link).

i'd like to install evo-all in order to have a posibility (all together):

- 3x lock remote start by oem keyfob;

- remote start by my alarm system/remote starter;

- when the engine was remote started (by 3x lock or remote starter) and working:

            - no any lights or wiper are switched on (and after remote started engine stops the lights are off too);

            - open (unlock) the driver door (and/or all doors) by pressing keys on doors (keyless entry), after opening a door the engine will not stop (with no push button pressed if possible);

            - open doors by my alarm system (engine continues working too).

- it might be fine if the retained accessory power

if my desires are reachable:

- what is the version number of firmware should i flash

- what should i do to adjust the evo-all correctly (settings, sequence of operations)

- where should i find the installation guide?

thank you.

Nissan Murano 2003 - Guide is incorrect

Sun, 19 Jan 2014 13:07:28 +0000

I know this is going way back, but I am doing a 2003 Murano today and noticed that your guide for it is incorrect. When you first pull up the 03 Murano from your list of vehicles, it says the EVO-ALL performs lock and unlock. Then, when you open the guide, it shows the wires from the remote start arm/disarm outputs controlling the lock/unlock.

Also, the picture you have listed for the BCM on the diagram is wrong.

Thank you,

Justin

2013 Nissan Murano Evo-All Standalone sometimes no key and transponder picture in display when remote starting.

Sun, 22 Dec 2013 13:47:30 +0000

Hello,

I have a 2013 Nissan Murano with the evo-all acting as a standalone remote starter. When attempting to remote start, sometimes it works, and sometimes it does not. The times it does not, on the vehicles display it comes up as "no key" and then switches to an image of no key in the transponder port. Does this have anything to do with installing a diode? I see on the PDF install guide under parts listed is one diode, but it is not shown anywhere in the schematic on where to install said diode.

Module de contournement CAN-SL2

Tue, 10 Dec 2013 22:57:20 +0000

J'ai chang

2009 Nissan Murano Remote Start using an EVO-ALL

Fri, 06 Dec 2013 12:07:07 +0000

Parts required list a diode, but the schematics don't show where?

EVO-ALL - no longer remote starts and serious lack of horsepower

Fri, 29 Nov 2013 12:56:03 +0000

I have an EVO-ALL Hardware Version 5 that was working fine until a couple days ago. I used it to remote start my Nissan Murano 2009. I hit the FOB LOCK 3x and it remote starts the car. It stopped working a couple days ago and when it stopped working I noticed the car has a significant loss of horsepower. It is almost it has no "overdrive" anymore. when i press the gas peddle to the floor nothing really happens.

I removed the box and the horsepower is back, when I hit the gas peddle to the floor it moves. I put the box back in and the symptoms are back.

I removed the box and update the firmware as of 11/28/2013 and put the box back, no fix. the remote start does not work and the loss of horsepower is there.

I purchased this in Feb 2013 - what do I need to do?