<?xml version="1.0" encoding="utf-8"?>
<rss version="2.0">
<channel>
<title>Questions &amp; Answers - Recent questions tagged not-flashing-blue</title>
<link>/en/qa/tag/not-flashing-blue</link>
<description>Powered by Question2Answer</description>
<item>
<title>Can&#039;t complete Step 5 - Blue LED don&#039;t Flash. Audi S4 2014</title>
<link>/en/qa/118183/cant-complete-step-5-blue-led-dont-flash-audi-s4-2014</link>
<description>Anyone can help me?&lt;br /&gt;
&lt;br /&gt;
I&amp;#039;m Stuck on Step 5 while programming my EVO-ALL with the T-Harness EVO-AUDT1 on My Audi S4 B8 (2014).&lt;br /&gt;
&lt;br /&gt;
The BLUE LED doesn&amp;#039;t begin flashing.&lt;br /&gt;
&lt;br /&gt;
CAN Connections are Good. I Measure round about 3V on the Whit 5 Pin connector between Grey and Grey-Black.&lt;br /&gt;
&lt;br /&gt;
Grey-Black goes to Orange-Brown (CAN-Low) and Grey goes to Orange-Green (CAN-High) like in the Guide described.&lt;br /&gt;
&lt;br /&gt;
I have connected these Cables at the CAN Connector near the Relays at the left bottom under the Driver footwell.&lt;br /&gt;
&lt;br /&gt;
&amp;nbsp;&lt;br /&gt;
&lt;br /&gt;
S/N: 001A06905491&lt;br /&gt;
&lt;br /&gt;
&amp;nbsp;&lt;br /&gt;
&lt;br /&gt;
Thanks!</description>
<category>Audi</category>
<guid isPermaLink="true">/en/qa/118183/cant-complete-step-5-blue-led-dont-flash-audi-s4-2014</guid>
<pubDate>Tue, 20 Dec 2022 16:17:44 +0000</pubDate>
</item>
<item>
<title>The led cannot be solid blue in the first step</title>
<link>/en/qa/100383/the-led-cannot-be-solid-blue-in-the-first-step</link>
<description>I bought a EVO-ALL and T-harness for my 2009 silverado 1500. I connectted the T-harness to my truck. I press and hold the button on then EVO-ALL, then plug the 4-PIN data wire to EVO_all. But the led on EVO-All cannot to be solid blue. So I have no chance to release the button. I waitted long time and tried sereral times. &amp;nbsp;Same problem. So I cannot &amp;nbsp;pass the first step when I tried to install it.&lt;br /&gt;
&lt;br /&gt;
One more question, the EVO_All I got shows EVO_RS on the box, not EVO-GM. But the T-harness is Thar-GMt4. Is it the problem. Thanks,</description>
<category>Chevrolet</category>
<guid isPermaLink="true">/en/qa/100383/the-led-cannot-be-solid-blue-in-the-first-step</guid>
<pubDate>Sun, 06 Dec 2020 20:58:21 +0000</pubDate>
</item>
<item>
<title>Stopped working couples months ago, installed last fall</title>
<link>/en/qa/99088/stopped-working-couples-months-ago-installed-last-fall</link>
<description>2013 ram 3500, no lights, no bad fuses</description>
<category>Ram</category>
<guid isPermaLink="true">/en/qa/99088/stopped-working-couples-months-ago-installed-last-fall</guid>
<pubDate>Mon, 26 Oct 2020 15:24:39 +0000</pubDate>
</item>
<item>
<title>Installation not complete on 2018 F150, last step left on solid blue</title>
<link>/en/qa/96939/installation-not-complete-on-2018-f150-last-step-left-on-solid-blue</link>
<description>Every step was complete as follows:&lt;br /&gt;
&lt;br /&gt;
1) plug in T harness&lt;br /&gt;
&lt;br /&gt;
2) while holding down black button connect the black plug on top of module&lt;br /&gt;
&lt;br /&gt;
3) colors go through sequence, release on solid blue&lt;br /&gt;
&lt;br /&gt;
4) plug in white plug of bottom of module&lt;br /&gt;
&lt;br /&gt;
5) turn key to on position&lt;br /&gt;
&lt;br /&gt;
....it does not go through rapid flash after this. Instead it stays solid blue.&lt;br /&gt;
&amp;nbsp;&lt;br /&gt;
&lt;br /&gt;
ordered my flash link updates just in case. And helo would be great on how to get this working.&lt;br /&gt;
&lt;br /&gt;
Ford 2018 F150 2.7 l&lt;br /&gt;
&lt;br /&gt;
EVO-ALL&lt;br /&gt;
&lt;br /&gt;
Service # 001A06879807&lt;br /&gt;
&lt;br /&gt;
hardware Vr. 6&lt;br /&gt;
&lt;br /&gt;
firmware Vr: 4.18</description>
<category>Ford</category>
<guid isPermaLink="true">/en/qa/96939/installation-not-complete-on-2018-f150-last-step-left-on-solid-blue</guid>
<pubDate>Fri, 08 May 2020 13:23:56 +0000</pubDate>
</item>
</channel>
</rss>