Questions & Answers - Recent questions tagged not-starting

EVO One with T Harness 2019 Hyundai Tucson Standard Key Not Starting

Thu, 22 Jan 2026 14:08:20 +0000

The programming appears to have worked correctly. I got the flashing red, yellow, and blue lights initially, then the solid blue light. I turned the ignition to run and got the rapidly flashing blue light. And when I turned the ignition off, the blue light turned off as expected. However, when I try to remotely start the car, it functions the same as it did prior to the install. When the lock button on the remote is pressed the first time, the parking lights flash once, and when it is pressed the 2nd and 3rd times, the horn honks (not chirps) each time. It appears the remote is not being recognized. Any help appreciated. Thank you.

2018 Tiguan will not start

Wed, 13 Nov 2024 20:25:03 +0000

2018 VW Tiguan, STD-Key, Not digital cluster, AT

EVO-ALL firmware 64.06

THAR-VW6

Decrypted and programmed successfully, but when trying to remote start via lock lock lock from oem key, car turns on, but doesn't crank.

Tested while in the car and the depress break light (shift lock) was still illuminated. I wired in the Yellow/Red Break Out to Black/Red VESCM (+)Foot Break correctly.

Tested command start while in the car and depressing the break, works.

Please assist.

Remote inop after key replacement

Mon, 28 Mar 2022 16:47:50 +0000

Customer had a locksmith replace factory keys know remote start will not work. Do I need to reprogram the module or is there an easier solution the customer can do?

Will not remote start

Sat, 11 Dec 2021 16:48:36 +0000

Installed evo all

I press lock 3 times blue light will flash each time then the red light flashes ignition doesn't turn on and vehicle doesn't crank 2009 f150

evostart 2 not starting with app

Sun, 28 Nov 2021 15:01:19 +0000

hi, installed a evo one with a evostart2 car start with 3x lock. installed evostart with rfa2a ignition wire ok have power on red wire and ground on black programmed evostart several time but still doesnt work made master reset and reprogrammed still same problem. perform validation step on page 15 of the guide ignition came on and door unlocked and ignition turned off. retried still no start with app.car start with 3x lock.im in the red coverage zone and my personal car which has evostart works fine.so coverage shouldnt be an issue except if its not the same between evostart and evostart2. evostart demand firmware 1.21 minimum i have 1.25 could it be the cause or maybe something else im pretty much lost at this time since every time i programmed i got the flashing blue then the green led. like it should tried programming with the switch and the brake pedal which seemed to have work but no luck.

remote start inop

Wed, 17 Nov 2021 21:36:30 +0000

Fortin Evo One 002B04 128202 AT loop not cut

2021 Nissan Versa Manual Transmission push button start

Firmware: 7.48

A1, A2, A3, A4, A7, A8, A9, A10, B1, C1, D6 are on and all others are off including special functions

RES firmware 1.25

2.1

3-1

4.1

6.1

7.1

8.1

9.1

10.1

11.1

11.4

12.1

13.2

14.2

15.1

16.5

18.1

19.1

20.6

21.1

24.1

26.1

29.1

30.1

31.1

32.1

33.1

35.1

36.2

37.1

38.2

39.2

when trying to activate (lock-lock-lock), the blue light comes on with each time the lock button is pressed and at the same time the red led next to the loop blinks rapidly. after the lock lock lock, the red light blinks twice and then goes back to blinking rapidly

i have checked all the connectionsto make sure i did not miss anything

my evo one with thar-ma30 harness will not start vehicle

Mon, 08 Nov 2021 14:37:28 +0000

I have a 2017 mazda 3 manual- transmission, I have installed an evo-one unit with thar-ma30 harness.I am using the factory remote to start the vehicle. The remote responds to the unit by lighting up blue when locking and unlocking the doors. It also lights up amber when the push to start button is pressed. The remote start can be activated when the vehicle is already running and deactivated by depressing the brake but will not start vehicle otherwise. Im guessing my options are wrongly configured.

EVO-KEY programmed for 2012 Sonata (key with immobilizer) but still not starting?

Sat, 16 Jan 2021 23:52:49 +0000

I purchased an EVO-KEY to work as the bypass on a OEM hyundai remote starter. I installed the remote starter successfully however I needed a bypass. I ourjsed the evo-key and installed and was able to get it programmed as instructed. However, the immobilizer is still not being bypassed. What am I missing here? I don't have a data link so everything is hardwired.

2008 Ford Focus Crimestopper/Evo-All

Mon, 11 Jan 2021 19:43:11 +0000

I have tripple checked all of the wiring between the two units and they all match the TIP sheet i got from MPC. the Evo-All seems to go trough all of the programming steps i bring it in and do the dycriptor and it says everything is good and happy. also all of the recommended setting are set up and saved to the Evo-All. I take it back to the car plug it back in and hit the lock button three times and the cluster comes on but the security light flashes like crazy. ive treid talking with tech support on the MPC side and they are swamped and getting a responce sucks. im going to keep digging through all of these questions from everyone else and see if i can find something but this has been a huge headache. thank you. EDIT: After i plug everything back in after dycripting the key and i try to start the car from the OEM fob the yellow light on the Evo-All stays on. it does the same if i start the car with the key. BUT if i start the car with the key and hit the lock button 3 times i can here the two modules kick on and i can pull the key out of the ignition and the car will stay running then i can hit the lock button three more times and everything will shut off.

Evo-all 2014 Ford Focus. Lights and dash turn on. No start.

Wed, 02 Dec 2020 22:19:55 +0000

Put in T harness and finished programming portion for stand alone key. Pressed lock 3x to start and dash lights up, radio turns on, then everything shuts off. Engine does not start. Firmware 71.52. Something im missing?

Cracking but not starting 2016 Hyundai Sonata standard key - EVO-ONE will T-Harness THAR-ONE-KHY2

Fri, 09 Oct 2020 09:06:20 +0000

Hi i want to ask ask about EMC COM wire it's missing from my car there is nothing in it's place the car cracking but not starting because the device cannot decrypt the Security code for the car to start it

I clicked lock 3X and but the key on its place the remote starting succeeded

But without the key normal remot starting cracking but not starting

I think the ems com it's there but not on the same place

I need help

all installation ok doesn't work with app but antenna receive signal

Mon, 23 Dec 2019 07:53:11 +0000

all installation ok but not work on application but antenna receive signal

remote start inop after installing rf kit

Sat, 30 Nov 2019 11:40:08 +0000

i just installed evo-all with t harness on a 2014 rav4 push to start. Tested after install and all working. I installed a MyCar rf kit and installed/programmed per enclosed instruction and now remote start will not start car with factory remote or app. Lights come on and blink but does not start

The REquest Returned an Invalid Code

Wed, 06 Nov 2019 15:44:39 +0000

whenever i open the APP it gives me an error of "The Request Returned an Invalid Code" and the Engine start from the app does not start my vehicle. did not have this issue last year.

how would i resolve?

2008 Civic will crank,but wont start

Fri, 01 Nov 2019 18:38:49 +0000

My 2008 Honda Civic will just crank,but wont start. The key chip warning light comes on during cranking. i tried doing it with the key in the ignition and still wont start. The car will start and run fine when started with just the key. It seems to have something to do with the chipped key. Any help with this?

evo-all on an escape doesn't initiate a start signal

Sun, 25 Aug 2019 13:23:16 +0000

2016 escape with an evo-all unit. the unit will not give a start signal on remote start. it detects the remote 3x lock (ie. blue light x3) but no red light. as per another suggestion the unit will give a red light when i ground the dk blue wire(ground while running) indicating that the unit is progammed correctly.

what should i be checking next?

2014 Chevy Cruze dash lights up but no crank

Sun, 07 Apr 2019 13:06:35 +0000

I installed my EVO All (Service# 001A06 853981) in my 2014 Cruze. When I push the OEM lock button 3x, the dash lights up but the car does not crank. All doors, trunk, and hood are closed. Options C1, D1, and D2 are all ON.

2018 f250 "check brake system"

Thu, 17 Jan 2019 18:55:25 +0000

I did an evo all install on the 2018 f250. It appears to use the factory remote start protocols. It worked fine for a month, then the truck sat for a week and it wont remote start and it says "check brake system" on the dash. I cant find any issues online. It only happes during remote start. It is a diesel tow truck.

001A06 826055 programmed but will not initiate start sequence?

Sun, 23 Dec 2018 23:02:27 +0000

Hello,
I have a 2011 GMC Sierra HD...

The module is programmed and responds to the factory key fob. When I press the unlock button, the blue LED light flashes and the locks work.

but when I press lock button three times - It does not inittiate start sequence. I currently was trying to hook it up with no peripherals, just the module connected to the transponder and ignition.

Am I missing a step?

I noticed on the harness there are two male connectors left that I have no place for under the dash,
and a two pin female connection on the module that does not seem to be for anything under there as well.

Please advise. thanks

2013 caravan not starting

Sun, 09 Dec 2018 15:14:53 +0000

programming appears to have worked. blue led flashed with each press of oem fob lock. car does not start. purchased a packaged/pre programmed unit with t harnass. slick install. but no start currently. ground is good at black wire. power is good at yellow/blue wire. no signal apparent on yellow/red. no other LEDs flash or turn on.

2017 Cherokee Not starting

Tue, 04 Dec 2018 13:21:21 +0000

I programmed the entire unit but the vehicle refuses to start. The evo all module blinks blue when i press the lock button. I dont know what else to do please help.

Linker LT1 not starting vehicle

Tue, 16 Oct 2018 08:23:20 +0000

Evo one, 2017 sonata reg key, oem and aftermarket remotes working, on the my car app it sees voltage and red and green lights are lit on LT1, I programmed the LT1 to module but it won't start vehicle

2017 Ram 1500 Tip Start, Will Not Remote Start

Thu, 06 Sep 2018 18:44:41 +0000

Details:

2017 Ram, Gas, Tip Start, CHRT6, OEM Remote

Flashed with standalone, T-harness, with built in alarm, 74.[37] firmware, 6.0 hardware.

No hood pin, valet switch, or parking lights connected.

C1 and D1 enabled, #8 blue wire does not turn red when grounded.

Everything seems to be installed correctly. The key programs without issues. Flashes without issues. The blue light falshes each time the lock button is pushed. The yellow light comes on when it is started with the key.

Problem:

When I attempt to remote start (3x lock button on the EOM remote) nothing happens on the unit or in the truck. No attempt to start, no dash lights, nothing.

Any advice?

2012 Toyota Camry SE will not Remote Start

Sat, 09 Jun 2018 23:09:10 +0000

I have installed the EVO-One, Thar-One-Toy4 T-harness and Programmed the One with option D2. Installed unit, programmed the unit per guide #71411 and still the unit will not remote start. I have done everything in the Guide and I even turned off the Valet Mode, but I still don't get any remote start from the unit. No lights on the unit are illuminated constantly and no lights flash when using the Factory remote to remote start the vehicle. Does this unit need a seperate remote to remote start the vehicle? Do I need to program the EVO-One to use the Factory Remote? There is no instructions on needing to program the unit to the factory remote. The main reason for this install, was to use the Factory Remote to remote start the vehicle.

2016 Ram will not remote start

Wed, 09 May 2018 12:03:42 +0000

Just installed new unit with proper flashing and updated firmware and vehicle will not remote start. Blue light on unit flash with remote signal but that’s it. No crank or anything. Checked all connections and verified correct flash and decryption. Yellow light on unit is on when I manually start the engine.

Stopped starting

Thu, 12 Apr 2018 07:06:56 +0000

Installed the remote starter a little less than a year ago, a couple days ago it stopped working, when I attempted to start the car the horn beeps and the parking lights turn on, then beeps again and does that cycle 3 times. Ocassionally it starts when I use it, maybe once every 10 times I try. The vehicle wasn’t moved at all between the times it doesn’t work and the time it did.

2004 TSX Crank but won't start

Mon, 12 Feb 2018 22:42:40 +0000

Hi All, I'm a bit stumpt on this one, I have a 2004 Honda Accord euro (Australian version of the Acura TSX) i'm using an EVO-ALL with Compustar FT7000, the EVO-ALL has programmed correctly but the car will only crank on remote start and not start, put the key in the ignition and the car starts fine I have reversed the white red and white green which did not fix the issue and I have tried earlier firmware which also didn't fix the problem, when the remote start engages the yellow and red lights light up on the evo-all. If you start with just the key only the yellow light is lit. anyone have any insight it would be greatly appreciated alos the car will start with the key even if the security light connection is cut which leads me to think it is to do with the data wire which is connected to the light blue wire of the evo-all (i have checked twice to make sure it is not connected to the light blue/black wire.

Regards

Chris

2013 F150 - EvoAll erased my 2 factory programmed keys

Fri, 19 Jan 2018 17:22:07 +0000

After I reflashed my unit I went to install to see if programming would work this time (several failed attempts prior to flashing). In the process I plugged the black 4-prong connector into the unit while holding the programming button down and released when LEDs were Red and Blue. Stupidly I then forgot to plug in the rest of the connectors before proceeding to programming. After cycling the two factory keys and waiting 3 seconds on each as the instructions say, the locks cycled and nothing happened (as expected with the other connectors not plugged in). HOWEVER, when I went to start the truck after unplugging the bypass module, the truck no longer starts. Neither key works now. They will lock/unlock the doors but turning the ignition does nothing. I realize my mistake in programming, but is there any way to reprogram the keys??? Or am I now stuck with a truck that has no remaining programmed keys that will start the vehicle let alone program anything whatsoever???

2011 6.7 f250 start system fault when trying to remote start

Sun, 07 Jan 2018 13:39:47 +0000

I programmed the unit. Loghts come on truck turns on then right back off then back on then off then doesn’t start.

the truck is 6.7 diesel. The service number for the unit is 001A06 783518. Tried reinstalling multiple times with now luck.

2013 Dodge Caravan connected and programmed but not starting vehicle.

Mon, 01 Jan 2018 13:25:36 +0000

2013 Dodge Grand Caravan

Service # 001A06781796 Evo-CHRTx pre-loaded

Firmware 74-22

The yellow wire from the T harness has been connected to the yellow wire of the 20 pin connector.

Installation programming went fine and the device seems responsive but using the lock button 3 times does not start the vehicle.

Each time the remote lock button is pushed the module flashes blue once.

Will not remote start

Wed, 27 Dec 2017 13:32:57 +0000

I have installed the EVO NIST1 kit, programed with the flash link and connected the white/black wire to the brown wire at the push to start button. When pressing the lock button, the EVO All interface module lights up blue with each press, but after the 3 presses it lights up red and yellow, then red. The dash does not light up and the brake lights do not come on when pressing the lock button.

2007 ES350 EvO One will not crank when remote start.

Wed, 27 Dec 2017 04:35:10 +0000

I have installed all the wiring according to Guide #19101. The module appears to successfully have programmed to the car, however, when I do the 3 button push on the factory remote it does not start the car. I have attached the rf642 and was able to successfullly program one of the remotes. When I try to start the car via the 2 way remote, the parking lights come on and it it looks like it is trying to start, however, none of the dash lights come on. The red led by the cut loop wire is blinking and after about 30 seconds it quits attempting to start. I can also hear sounds in the car as if something was activated, When it finally quits, the partking lights appear to blink 4 times, which should indicate no tach. But Im not sure what to look for in that.

And finally, the 2 way remote was controlling the locks at one point, but that has stopped and I am not able to program the second remove via the valet switch or by the ign on off on method.

Edit: I have been able to get the other remote to program and now the remotes are making calls to the bypass/RS, however, when I try to RS the car it clicks, RED LED comes on, but it does not go ignition. After it fails twice, the lights blink 4 times still. Not sure why it wouldnt be getting tach at this point.

car will not remote start

Sat, 18 Nov 2017 19:50:40 +0000

I have an 2015 kia sorento. installed evo one. have crimestopper rf kit. programs correctly. can lock and unlock. When i push the start button the locks lock, the red light on the top of the unit goes on, the parking lights flash 4 times, then the blue light flashes 2 times but the car does not start.

2016 Ram 1500 dash lights up but no crank

Mon, 30 Oct 2017 14:40:17 +0000

Hooked up all the wires per user manual. Everything on the key works fine, lights on the dash come on when I hit the lock button 3x but I get no crank.

2008 Acura mdx Cranking but sometimes not starting

Sat, 05 Aug 2017 13:38:38 +0000

2008 Acura MDX once in a while it will crank over but will not start I do not have access to the units service # at this moment

2016 Chrysler 200 3 Flashes - No Tach Detected - Ignition on but no crank

Wed, 18 Jan 2017 19:53:56 +0000

2016 Chrysler 200 3 Flashes - No Tach Detected - Ignition on but no crank:

I have walked through the troubleshooting guide and checked all of the programming/wire issues that could occur. Any other items to test or check to get the car to remote start?

The car attempts to start twice before failing and providing the diagnostic codes.

Why is my car starting and stopping and door is always open if module unplugged.

Mon, 26 Dec 2016 13:10:20 +0000

2012 Ford fiesta lots of issues. Starts and shuts down over and over. If module is unplugged driver's door is always open.. headlights staying on when switch is off... This module is being installed by a 30 year certified technician

Cranking but not starting

Sun, 06 Nov 2016 06:05:55 +0000

Good day. Ive just install Evo-One on my 2013 Hyundai Santa Fe Key Start and followed every wiring to be installed and programmed. Now when i remote start, all it did is cranking then it will stop. Can you help me with my problem. Thank you.

Update: Ive double check all the wirings again, everything is in its place. Try remote start, still cranking only. Now i also check the leds on evo-one no blue lights when lock-unlocked on oem remote. I think everything is mess up right now. Help pls. Thanks.

2016 ELANTRA PTS will crank but not start on first try

Tue, 01 Nov 2016 10:24:43 +0000

Using evo-all module will crank but not start the first try but when the remote start trys it agian it will start.

Why is there an anti-theft message on my truck when trying to remote start my truck?

Sun, 30 Oct 2016 04:21:25 +0000

I have the Evo All with Tharness. The module is able to start my truck with 3 lock presses. However, when I try to remote start the vehicle using the remote starter connected to the Evo, the acc and ignition turn on but when it seems to try to start the vehicle (no crank), the display in gauges says Anti-theft active and everything turns off. I have tried with both the vehicle locked and unlocked with no difference. What can be the issue?

Crank but will not start

Sat, 11 Jun 2016 00:42:59 +0000

The EVO-ONE is installed and programmed successfully. I could only programmed one of the remotes, the second remote could not be program for some reason. After programming the first remote, the car will crank but will not fire. Am I suppose to do something with A4 (-) ignition and A5 (-) start wire on the 20-pin? I also have A15(-) hood/door hooked up to dome light, is that correct for security? The alarm feature is not working.