Questions & Answers - Recent questions tagged not

purchased EVO-CHRT4 for 2011 jeep grand cherokee

Fri, 10 Oct 2025 18:59:38 +0000

I purchased the EVO-CHRT4 for a 2011 jeep grand cherokee. Installed per instructions, also tried a youtube install. All steps went as required, per instructions. jeep will not start remotely. please help.

flashlink wont connect to evo all s# 001A06 682920

Tue, 11 Feb 2025 10:31:45 +0000

I think I reached the flash limit as the lights come on the evo all with the flash link but it will not detect oit. In bypass its a solid red light and in remote start its all the flashing at once. Any way to fix this? I tried the reaet procedure, but didnt work. Its for a 2013 silverado.

Mazda 3, 2018

Sun, 02 Feb 2025 10:18:43 +0000

The unit does not read the key, when the ignition is turned on nothing happens, the blue indicator continues to light

Mazda 3, BN, 2018

I loaded the latest version of Flashlink which is 4.51 and is says PC is unable to connect

Sun, 18 Dec 2022 16:55:29 +0000

I have version 4.51 flashlink installed and flash link unit shows a red and green light but the software says the PC is unable to connect to the flash link updater. The red and green lights are on no matter if the EVO-ALL is connected or not. No lights on the EVO-ALL.

Ignition turns on but doesn’t start

Mon, 12 Dec 2022 22:50:50 +0000

I installed Crimestopper RS4-G5 in my 2003 Chev Silverado 1500 5.3L auto. I also installed the Fortin EVO-All and flashed it with the Fortin Flash-Link Updater 2. I've triple checked the wiring and triple checked the instructions when I programmed it. You hit the start button, it locks, ignitions turns on and just sits there and that's it. After that the yellow light and red light stays on on the EVO-ALL.
Any help would be appreciated as this has been a long on going project.

Box does not light up when 4-pin is inserted.

Fri, 10 Dec 2021 07:53:08 +0000

Hello.

I bought a EVO-ALL Evo-TOYT6 for a Toyota Auris Hybrid 2018.

I installed the T-harness as recommended in the installation manual, but the box does not light up when i insert the 4-pin in it, when I try to program it.

The Box is flashed and should be good to go.

Do you have any idea what the problem could be?

Guide # 73271 used

2016 Tiguan brake and accessories come on but does not turn over, cycles twice.

Thu, 02 Dec 2021 19:16:03 +0000

All lights check out to be correct. Car turns acessories on and applies brake then nothing, then it tries it again and stops for good after that. I have a keywrap right now. Do i the the TB-VW?

Evo one with ftx64w 2way kits. Hyundai elantra 2009

Sat, 25 Sep 2021 22:01:10 +0000

Mine will crank and start only if oem key mounted. If not mounted will crank but won't start. Please help Thanks

evo all starts once and then dont starts

Wed, 20 Jan 2021 10:11:05 +0000

help please, my car mazda 6 2014 push to start , i done all correct , 3x lock the car starts first time , after that i try to start 2nd time evo all dont start the car what is wrong? help please

evo all 2015 chevy trax step 4 yellow only blinks 4 times then goes yellow and red solid

Tue, 22 Dec 2020 21:44:24 +0000

teck support says the brown wire is not making a good connection so i checked and everthing is making good contact and from the obd2 port terminal one (green wire i am curenly plugged rite into it to make sure that is not the issue. checked with meter and the connection is reading .5 of an ohm. so that is not an issue any more if it was. just seeing if anyone know where to go from here thanks

2018 SUBARU PUSH TO START ATTEMTS TO START BUT NO CRANKING

Mon, 14 Dec 2020 11:08:02 +0000

I have installed and programmed the Evo ONE module on 2018 Subaru Outback Push to Start. The module have been programmed and dycrypted when everything is connected, and 3xlock button is pressed on the remote, the car tries to start 2 times, but there is no cracnking sound on the engine. Please help.

I have also tested the voltage from the root wire and the end(connector), on both sides Immo wire puts out 10.9 Volts.

Another thing I have tried to get the voltage reading oin the Yellow(+Starter) Evo Module wire and it is not giving me any readig (0 V), and the main harness WiteGreen(on the green socket Pin34) isn't giving any voltage reading either, is it supposed to be 12V, when the car attempts to start the wire give 12V. any clues?

P.S. When the car tries to start the starte make clicking noise, but the engine won't crank, so basicaly the starter is in a zooming stage.

2018 Subaru Push to Start attemts to start but no cranking

Sat, 12 Dec 2020 14:57:07 +0000

3x times pressed , but no cranking everything else turns on. Lock and unlock no remote start

Mon, 30 Nov 2020 14:37:21 +0000

lock and unlock work good

2014 ram 3500 push gas push to start pressed 3x turns on no crank

Mon, 30 Nov 2020 14:27:51 +0000

lock and unlock work good

no crank after 3 lock presses (blue led each press), red blinks 5x

Fri, 13 Nov 2020 19:14:53 +0000

System quit working after dealer flashed ECM. Updated flash-link and relearned key, but no crank.

Toyota Rav4 2020 Push start doesn't crank.

Sun, 08 Nov 2020 19:48:59 +0000

Installed following instructions. Remote is manufactured 2019.11. Tried various firmwares - from the one recommended in the instructions (79.57), and the newest version (79.64). When plugged in, blue light shines dimmely. When pushing the car-start, the ignition lights come on but doesn't crank -it tries 2 times and turns off.

2008 Pontiac G5 Factory with Fortin

Sat, 31 Oct 2020 10:00:31 +0000

I have a 2008 Pontiac G5 it originally came with a factory remote start however it stopped working a year ago. I was wondering if I can install a fortin all in one? Thanks

do i need a new t harness upgrading from a evo all to evo one 2016 chevy silverado

Mon, 20 Jul 2020 18:20:13 +0000

cant add a rf642 to the evo all manufacturing date 12/14

Buick regal 2016 rf912 lock & unlock not work

Wed, 10 Jun 2020 08:46:21 +0000

i have RFK-912 and EVO-ALL with THAR-GMT6 standalone installation for buick regal 2017

having some issues with G option off pressing on RFK912 Remote lock and remote start the car, but not unlocking, only sound is coming 2 horns, but doors never open, and when i remote start the car then remote stop, car doors open then after 5 seconds it closes

Then when i make G option ON, remote start only works but lock and unlock cannot be done at all from RFK912 only sound is coming as if order recieved but no real action is being done, and when i press for remote start and vehicle is started and then try to stop it by remote stop, car stops and open the doors and never close it automatically, i have to use the original car remote to close it

can you tell me what is wrong? or any other connections needed ?

2014 LEXUS RX350 EVO ALL , EVO ONE DOES NOT WORK

Fri, 17 Jan 2020 13:39:24 +0000

2014 Lexus rx350 made in canada ,evo one , evo all not working

All connection correct ( guide 76891), program modules ok ,blue led blinks ,door lock unlock and luck ( for disarm) , and no ignition-cluster is dark ,engine no crank .I try 2 evo all and one evo one and still this same problem. All Modules 2019 year.

whats wrong??

2013 NISSAN ALTIMA PUSH TO START NOT STARTING

Sun, 03 Nov 2019 19:00:10 +0000

I HAVE A 2013 NISSAN ALTIMA 4 DOOR SEDAN. I INSTALLED THIS WITH A T-HARNESS BUT IT KEPT GIVING ME PROBLEMS. THE PROBLEMS WAS THE CAR WOULD NOT START OR SHUT DOWN WITHOUT REMOTE STARTING THE CAR. SO I HARD WIRED IT AND NOW THE IGNITION COMES ON AND NO START.

SERVICE NUMBER 001A06677653

EvoAll 2019 Toyota Rav 4 FWD Push to start not starting engine

Fri, 01 Nov 2019 18:59:41 +0000

EvoAll Regular installation without takeover. GUIDE # 83841

Programmed Flash-Link4 with latest firmware, and EvoAll updated to latest version as well.

As a first time installer, I've installed this to the best of my abilities. Here are the EXACT steps that i took;

1- (-)start/stop TO EvoAll A19

2- (-)lock TO EvoAll A20

3- (-)unlock TO EvoAll A10

4- EvoAll B4 TO (+)12V ***I didnt, but must I install a 7.5 Amp fuse???***

5- EvoAll B3 TO Ground

6- EvoAll A1 TO (+)Ignition ***I didn't but must I install a 1A Didode???***

7- (-) Steering Lock TO EvoAll D6

8- (~)Can High TO C3

9- (~)Can Low TO C4

After programming the EvoAll, 3xLock will turn on the ignition, then turn off, and make a second attempt to turn on, then off again with no engine crank at all.

AM I MISSING SOMETHING(S)???

2014 Ford edge Remote start works. Key start doesnt

Mon, 28 Oct 2019 17:53:47 +0000

Installed evoall with t harness, programmed and remote start works. However, if I try to use the KEY ONLY to start it won't. Nor will the car shutoff after ive remote started and inserted key. Remote start WILL ONLY shutoff using the lock unlock lock sequence.

OEM Remote will not unlock/lock car after remote start

Sat, 19 Oct 2019 23:46:14 +0000

When I remote start my 2016 Hyundai Tucson with the OEM remote (3x lock button) I am unable to use the remote to unlock/lock the vehicle and have to use the phyiscal key to open the door. There are previous questions about this, but I have not found an answer yet. Is it a programming option or did I wire something wrong?

Evo one alarm shock sensor warn away only

Wed, 05 Jun 2019 01:20:23 +0000

Evo one alarm. Shock sensor only triggers warn away. When tested without sensor plugged in short pulse triggers warn away. Long pause does the same. Cannot get full alarm to trigger at all. 002807 242359

2009 toyota highlander hybrid push to start, just start accessories but not crank

Sun, 19 May 2019 23:25:32 +0000

DASH AND ACCESSORIES COME ON AFTER 3X LOCK WITH SOLID RED AND AMBER LED BUT NO CRANK.

2007 Ridgeline will not Remote Start with Encore6 alarm and Evo-All

Sat, 04 May 2019 14:06:04 +0000

When i programmed the Evo the instructions says the red light will blink 10 times, it blinked 8. The blue light continued to blink, i then turned the key to off. The truck tries to start, but only cranks. I have wired in the factory alarm arm/disarm (pain in the ass with this truck).

The issue is the immobilizer (key icon) blinks on my dashboard when trying to remote start. Ive tried to reprogram 3x, its finished all 3 times (8 red blinks, blue continues every time). It will start if a key is in the ignition, or next to it (duh).

Im using the remote start command from the Encore6 (safety start, press * 2x)

*Yellow light is on during any command, just checked. Blue light flashes with commands except remote start functioning. When doing remote start the yellow and red lights are on solid, and return on the next try.

Thank you for your help.

Constant res light on evo-all

Sat, 20 Apr 2019 10:34:01 +0000

2014 Toyota Tacoma withvthe blavk ley stamped G.

installed the unit, got all the wires hooked up correctly.

When I plug the black, 4 pin connector into the evo all to start programming, the red res light comes on and stays constant red, no matter what I do the red light will not go away! Tried a master reset, nothing still red ligjt.

What could be my problem?

2018 Dodge journey, on programming procedure step 6 the light will not change from yellow to red, all wire are good

Wed, 10 Apr 2019 20:52:43 +0000

On a 2018 Dodge Journey, I can not get an evo all to work. on the programming procedurs step 6 the light will not change from yellow to red, check all the wires, flash the module with the flasher and put the firmware 74.32, didn't work, the programmer was suggesting the firmware 74.18, try it didn't work. Updated the flasher and flash all the firmare again and didn't work. I check all the wires one by one and they were good.

Need help please

Evo-one install on infiniti 2008 G37 6 speed manual but only lock and unlock work. Remote start does not work.

Wed, 13 Mar 2019 19:00:04 +0000

Hi, I’m installing EVO-one with Omega LINKR-TL2 on a 2008 Infiniti G37 6 speed push to start. I follow the installing guide #33251. I flashed the unit up to the latest firmware. Previously I had a DEI XL202 romote start that connected to EVO one. Tested the unit and only lock and unlock working but when attempt to remote start the car. Only see 3 parking light flash. So I though that it could be DEI XL202 is not functioning correctly so replace it with Omega LINKR-TL2 unit but still have the same result. I have been talking to Derek for his assistant and suggested to master reset both the bypass and remote start. Reset the module and reprogram with his suggested selection (BYPASS SIDE: A1-A11 -ON, C1 -ON, REMOTE SIDE: 8.2, 32.2, 33.3 AND 38.2) but have the same result. I’ve been doing a lot of online researching for the passed 2 week but still no luck. (Now only lock and unlock working) Your help will be much appreciated.

infiniti m35x evo all does not program

Tue, 12 Mar 2019 20:53:41 +0000

hello, I just installed an evo all in an infiniti m35x 2006, I have made all the corresponding connections but at the time of programming I find a problem, the instructions say that at the moment the blue light of the evo there is set flashing (last step) press the start button to turn off the vehicle and at that moment the blue light should turn off, but the problem is that it turns off but immediately the yellow and red light start to flash intermittently without stopping and so the evo remains all alone until I completely disconnect, what can I do, i checked the cam hight the cam low and the other connections and I notice all of them well.

Blue light on Evo all not link don’t pass of step 4 of programming using a THarr-Hon3

Sun, 03 Mar 2019 13:10:01 +0000

The unit don’t pass from step 4 on programation, on Evo -all at an honda car-v 2016 push to start

2016 h key Tacoma high beams not working after evo one install ? help !!

Tue, 26 Feb 2019 21:58:00 +0000

my high beams are not working now the it acts like it wand ts to but no good

Red LED on EVO-ALL but car will not crank. Dash and accessories come on after 3x lock with solid red led but no crank.

Wed, 20 Feb 2019 14:52:02 +0000

I believe programming was successful as the evo blue led flashes blue with remote lock presses. Red led comes on solid but with no engine start. 2016 GMC Terrain

2017 RAV4 AUTO HEADLIGHTS NOT WORKING AFTER INSTALL

Sun, 10 Feb 2019 22:03:09 +0000

Installed evo-all on my wifes rav4 now her auto headlights are not working.

Ego all does not blink lights when running

Fri, 01 Feb 2019 17:34:02 +0000

I installed the evo all on a 2010 rX350. The unit works fine but I did not connect the parking light wire because the unit does flash the parking lights to confirm start. I figured it would blink the light once in a while while running like during start. I assumed it used the can bus to do it. Is that possible or do I have to go connect the wire? Also, is there anyway for it to detect the factory hood pin using the can bus so I do not have to install hood pin?

Is the yellow light on the module supposed to light up when both keys are inserted for programming?

Sat, 29 Dec 2018 13:32:56 +0000

Evo All with EVO-Fort4 cables

starter will not flash says reached its limit

Wed, 26 Dec 2018 09:41:06 +0000

my starter was acting up. tried to reset and update. I tried several times and eventually it said can no longer flash. I have a deisel ram 2500 2015 model. I remember when we set it up the first time there were alot of steps to get it right do to the truck. I have tried to reach out since the day before christmas and have not recieved any response.Please help rest it and assist with new progam.

thank you

Toyota Corolla 2011 G Key Made In Canada-evo one not working

Mon, 10 Dec 2018 21:38:59 +0000

Instalation Evo One to Corolla 2011 G key ,Ignition conector difrent color wires ,and only one wire to start( guide 23011 two wires for start).Problem is to program bypass like guide 23011-no flashing red/blue and after blue when ignition on.

Vin number this car :2T1BU4EE0BC698787

Ignition connector WHITE :

PIN 1 - Empty

PIN2 - RED

PIN3 - GREY

PIN4-GREEN

PIN5-EMPTY

PIN6-BROW

PIN7-BLUE

PIN8-BLACK

BLACK CONNECTOR 7 PIN

PIN1-PURPLE

PIN2-EMPTY

PIN3-BROWN

PIN4-BLUE

PIN5-EMPTY

PIN6-EMPTY

PIN7-GREEN

2017 ford transit cargo van locks not working after setting for a long period of time.

Fri, 09 Nov 2018 19:00:40 +0000

Hello i have installed a evo-all and viprer 5706 2 way alarm on my 2017 ford transit cargo van using thar1 harness. after setting for a long period of time or overnight the doors will not unlock with the viper fob and its a 2 way fob indicating the doors are unlocked but i have to ude factory fob to unlock them. if i go into astore for a short time the viper fob unlocks doors with no prblem. The evo-all is programed in can bus only becuase the van has no immobillizer. I noticed in the qustions ans answers sectioun that someone was having a similar problem and tech said you may have to add a relay to wake bcm. If this is the case were would relay be wired in and what would trigger it the alarm or module and were would connections be made? Just FYI when i remote sart the van after setting overnight doors unlock with alar fob just fine every time so im assuming this is my problem. any information would be greatly appreciated

Tank You

Eric

Toyota Sienna 2008 + EVO ONE no starting Car

Tue, 06 Nov 2018 21:18:01 +0000

Toyota Sienna 2008 -installation guide 58481 ,connection 1 ,program 1

programming bypas is ok -red light blinking and off. car is no running ,no blue light flashing when lock door with keyfob-no reaction

Firmware wersion 79.49 - i no try diffrent wersion program -problem is to many times flashing modules is blocked and problem unlock / ask me why used one module to many cars -to many times fortin not working and try second modules,sometimes from customer car when remote work perfect.

service no :002B07213899

No answer ok-more connection/diagram is bad no only for this car

Guide 58481 is incompletely and no answer and no help from fortin

I installing last 10 maybe 12 fortin products from my stock and change company

car will not crank

Tue, 06 Nov 2018 12:51:08 +0000

2013 chevy cruze lt automatic.

when pressing lock X3 ignition turns on then turns off without cranking. even with added RF remote will not start.

Mazda 6 and no more flashing

Tue, 30 Oct 2018 03:59:54 +0000

I have problem with mazda6 2017 push-to--start automatic evo-one with thar-maz1. its worked but gives errorcodes and cruise disabled when i takeover and drive, i tried different firmwares and now its locked - can't flash anymore. what options I have? It can work as well as before because now I have nothing

No blinking blue light when programming in step 4 of install guide for a 2018 Mazda CX9.

Sun, 21 Oct 2018 17:19:51 +0000

I bought the EVO-One and the THAR-ONE-MAZ3 T-harness for a 2018 Mazda CX9. I got the t harness installed fairly easy but am having trouble programming. I hold the programming button while I connect the 6 pin main connector, release when the blue light is solid, connect the rest of harness, press on 2x but the LEDs never flash as instructed. I'm not sure how to proceed from here, I've reset the module and tried a few times. The 20 pin connector has a bunch of lose wires on the t-harness, should this be connected to anything? From my understamding only the optional parking light wires needed hardwiring, everything else was plug and play.

2014 Subaru Impreza Basic ,EVO ONE NOT WORK

Sat, 20 Oct 2018 09:37:51 +0000

Evo One + Subaru Impreza 2014 Basic

Im tired installing evo one for this car ,all connection is ok regular installation but still no illumination blue light when lock/unlock.Program procedure is ok ,decryptor ok and still no work blue led.

evo-gmt1 will not operate

Tue, 25 Sep 2018 06:03:04 +0000

Hello, I have a 2017 GMC Terrain. I just installed the evo. I get a blue light on interface, but vehicle does not start. I do not have a hood pin or the valet toggle switch connected. I do not want either on my vehicle. I have the flash link and have installed what is reccomended on your website. What is wrong with the unit?

Evo all will not start vehicle via auto connect unit and will no longaer allow any updayes!

Mon, 10 Sep 2018 20:46:08 +0000

Can not start vehicle via after market starter

2017 Forester, standard key, EVO ONE, OEM alarm, remote start wont start

Sun, 04 Feb 2018 10:15:08 +0000

2017 Forester with Standard key

Wired with guide #57211 and used T-harness

flash link updater updated to current V:4.03

Evo one updated to 79.45 for the 2107 forester

evo one promgrammed in car and went good

I did not wire up the Power lift gate wire and the Hood pin wire

In the bypass mode I have A1-A9 selected ON, (A10, A11,B1 selected OFF), C1,D2 selected ON, (D3-D6 selected OFF)

In remote starter mode V:1.24 updated and only ones i changed were 6.2 selected and 38.2 selected

then did Dcryptor programming and it went fine

put the evo one back in the car and no remote start

all standard key features are working

i shut the door and can see the evo one and when i lock or unlock there are no lights coming on, on the evo one. isn't the blue light?

i thought it was IMO wires so i disconnected the red connector and tried to start the car and it will start but will shut off after a few seconds

when i pull the red connector back in and start the car, the red light on the evo one lights up soild

Service Number: 002B07 237674

Please Help!!!

I also tried the older firmware verison of the remote start mode and still NOTHING

Also I was driving home last night and my passenger door switches are not illuminating.

What is going on????

dark blue wire, driver door trigger - does not work

Sun, 28 Jan 2018 00:01:56 +0000

I have a 2011 nissan rogue intelligent key, I installed an evo one, everything works perfect, except the trigger of the driver's door (auto lights shut down ) dark blue cable, connect this cable to the negative of the door trigger, exactly as the instructions say , but I have the problem that when starting the remote start the vehicle turns on but after 2 seconds it turns off, check the problem and I find that when the remote starter start the dark blue wire gives a constant negative discharge and the sensor of the door trigger shows as if the door were open, I do not really understand what this dark blue wire is for and what function it has, disable it and the car lights normal, my question is what should I do or what is the problem, or I must configure thanks.

2009 Expedition Won't Start with Evo One

Sat, 13 Jan 2018 16:35:17 +0000

I have checked the wiring multiple times, the yellow loop is cut, option C1 is enabled, option 38.2 is selected, I've tried to increase the tach time and still I cannot get it to start. I did not wire the door trigger (pins A17/A18) [conflicting information on location of this connection] or the parking lights (E1) at this time.

I am conducting two key programming per guide 28331. After the first part (pg 6), I get it to work through step 5, but step 6 will not allow the car to start. The unit does flash the blue light upon each press of the lock button on the OEM remote.

I have also tried to continue with steps 7-15 and they all respond as the guide indicates it should. Step 16, I just get a solid red light.

I have also ensured that all of the firmware is on the most current versions.