Questions & Answers - Recent questions tagged oem

Red LED light will not do anything but stay on

Tue, 03 Feb 2026 11:33:52 +0000

I’ve checked every single wire so many times been working on it for two months. Red light will only stay solid so I’m guessing programming issue company I bought it from won’t help. Please help me somebody. also kid did not come with a remote start. I am using OEM key 2005 Honda CRV

2009 rx350 key sense

Wed, 13 Dec 2023 00:38:01 +0000

i have installed EVO-ONE-942 and INT-SL+. The car lock, unlock, remote starts. Everytime i remote start the alarm set off. i follow Guide # 90081. i did hook up the key sense wire. but i didint see any 2 pin white connector shown in the guide. when i remote start the alarm set off so i have unlock and lock and the car stay running. if i cant find the key sense wire. can i change the setting to unlock before start then lock after?

how do i wire up the door unlock so i can gain access to the car after remote started

Wed, 01 Mar 2023 13:44:31 +0000

I see that in the evo model their are wires to lock and unlock the doors for a 2014 Hyundai Santa Fe with Key start, however i cannot find any info on where to connect the unlock wire from the evo starter to the car so that i can unlock the doors after remote starting it.

Ford Remote Starter Conditions

Thu, 26 May 2022 20:54:59 +0000

2021 Ford F450

Does your remote starter solution only enables the OEM remote starter on this vehicle?

Would the EVO-ALL or EVO-ONE will still remote start this truck even if:

- CHECK ENGINE LIGHT IS ON.
- LOW FUEL LIGHT IS ON.
- VEHICLE BATTERY VOLTAGE IS TOO LOW

We are planning to install these on 4 work trucks

2018 Tundra, OEM alarm connection (orange wire)?

Sat, 13 Mar 2021 14:32:10 +0000

Nevermind. I figured it out.

2019 Honda Passport Elite Installing EVO-ONE

Mon, 22 Feb 2021 11:57:53 +0000

Hello,

Customer has 2019 Honda Passport Elite with OEM remote start thu the OEM remote/keyfob. Honda does not have or support the cellphone App to remote start the car. Customer wants me to install an aftermarket remote start with telematics so they can remote start the car with their cellphone. Is there something I need to do with the OEM remote start module before installing the EVO-ONE? Are there any instruction on how to make the EVO-ONE work with the OEM module or do I just remove the OEM module?

Thansk

09 altima evo-all w/thar-nis1 tharness. Wanted to add siren and shock sensor need wiring diag.

Sun, 21 Feb 2021 20:54:05 +0000

Evo,all w/thar-nis1 t harness, oem remote, standalone. Green wires are for lock n unlock. Where is siren wire ?

OEM KEY DEATH AFTER START

Tue, 29 Dec 2020 20:15:08 +0000

2020 Kia FORTE with EVO ONE and T-Harness. Once the car is started, the keys do not respond. Could you give us a solution? After checking the possible solutions that you offer us on your website, none have worked for us. Thanks in advance.

oem fob wont unlock doors and obdii powers my HUD when tundra not running

Thu, 24 Dec 2020 19:00:01 +0000

2017 tundra. so, i installed the evo one using the thar toy7. i also added the evo start 2. install and programing seemed to go well. But now my oem fob wont let me unlock the doors and when my truck is not runnuin, my aftermarket OBDII powered Head up display turns on and off making a beep sound every 20 seconds or so. I must have made a bad choice in the programing phaze.

OEM 3x Lock not starting 2011 Silverado 1500

Tue, 01 Dec 2020 23:28:12 +0000

EVO-GMT4

2011 Silverado 1500 Standard-Key. Programmed according to instructions on guide #59011. Installed using the included T-Harness. Programmed and decrypted using USB Flash Link. Re installed the module into vehicle. When I push the lock button on the OEM remote 3x the blue light flashes each time but doesn't start the vehicle.

Wire connection connections to controll oem remote after start Evo-all with GMT1.v2 T-harness

Tue, 28 Jul 2020 13:25:42 +0000

I have a chevrolet sonic/aveo 2012 and have now the evo all with GMT1.v2 installed and also already make the connection to the obd port1 and make the connection to my lightswitch. But my oem remote is not functional after i remote started. But there must be an modificiation to shut down also with the oem remote. Somebody can help me?

chevrolet aveo standard remote disabled after remote starting, starts anyway at the 5th lock not the 3th lock

Sat, 25 Jul 2020 12:17:34 +0000

i have the evo all installed with the GM1 t-harness, and i use my factory chevrolet flip key (aveo 2012 euro/sonic)

the car starts at the 5th time pressing the lock button, not the 3th time, and if i try the option lock-unlock-lock then it don`t work..

if i remote start the car then de oem flip key is disabled and get no response from the car, i can unlock the car with the key, and if i push the unlock button in the car and press the brake it turns off and starts normally (automatic)

license: (JV-198-N) Netherlands.

TRUNK RELEASE CONNECTION FOR OEM REMOTE - 2011 Acura CSX Bluetooth,Navigation

Tue, 10 Mar 2020 21:23:32 +0000

Can't find anything on the guide for the connection between the EVO-ONE and the trunk release wire. Which wire for the evo-one is used for the trunk release. The guide for the vehicle does indicate trunk open is supported. The guide only goes through connecting the unlock, lock, horn and parking light. When I hit the open trunk button on my remote (while the car is turned on via remote start) the parking lights simply blink and the trunk does not open.

Trunk release connection for OEM Remote - 2011 Honda Civic NAV/Bluetooth

Sun, 08 Mar 2020 10:53:59 +0000

Can't find anything on the guide for the connection between three EV-ONE and three trunk release wire. Which wire for the evo-one is used for the trunk release. The guide for the vehicle does indicate trunk open is supported.

OEM 3x Lock not starting 2007 Silverado Classic (now at flash limit)

Sun, 15 Dec 2019 17:25:48 +0000

I'm doing a first time install of the EVO-ONE (SN 002B048051) on my 2007 Chevrolet Silverado Classic 2500 HD Diesel and I followed Guide 61101 Rev 20190723 which stated the bypass FW must be a minimum version of 70.26.

The latest version of my flashlink software wants me to use 70.18 (highlighted in green) which did not work so I then upgraded to the latest version 70.39. I found at the latest version the module would not recognize the key programming procedure (all led's flashed at same time when powered on). I then tried going down one FW version at the time (from the latest) and found that 70.34 is the latest version that will work as per the guide and accept key programming without all LED's flashing when plugged in. I'm now stuck at that version and cannot set bypass options any longer since my flash limit has been reached (not sure if not being able to set bypass options is due to flash limit reached or the fact I'm now at 70.34 because I know 70.26 did allow me to set bypass options). Both 70.34 and 70.26 are greater than the guide requires

My remote start FW is 1.24 and I had enabled both options 38.2 and C1 along with other options for Diesel etc. According to the guide the 3x lock , heated seats etc should work on the classic and this module but I have yet to see success. When I start the truck with the key I see the yellow light come on showing the key is programmed however I do not see the blue light blink when pressing lock on my OEM remotes.

I do have the Fortin Rf642 rf kit on the way and will setup the module to use those however I wanted to enable the 3x lock on the OEM remotes in the meantime.

Can anyone point me in the right direction? what FW should I be running and can my module be unlocked so I can flash and configure it please? Is there some other wiring outside of the guide that I am missing?

Also can anyone confirm the options that should be enabled to trigger heated seats, remote defrost and heated mirrors?

Thanks

Honda civic 06 EX standard Key. Car then remote started. OEM remote unlock is not working.

Wed, 04 Dec 2019 15:25:03 +0000

Honda civic 06 EX standard Key.

Installed EVO One (updated with latest firmware1.24 aka 0.60, Hardware rev 4). D2 is off.

Wiring is according to the installation manual using Tharness Hon1, Rev 1.

Car remote startedusing 3x oem lock press. 3x lock stops the engine and then it unlocks the driver door.

If i remote start and then press unlock on OEM remote, it blinks the parking lights but will not unlock the door which is an issue.

I did connect the lock unlock wires on driver boot side clip. Also Tharness yellow wire is cut for IMMO + connections

SN 002B04 044514

Can you use the OEM Remote to unlock/lock after EVO-ONE remote start has been activated in Hyundai Tuscon 2018?

Wed, 27 Nov 2019 19:08:23 +0000

Looking to configure the EVO-ONE with a Hyundai Tuscon 2018 with OEM Remote, how will the OEM remote function after the car has been remote started. The guide says the remotes will not be operable during remote start?

Thanks!

Will any of these products work with OEM remote starter already installed

Fri, 25 Oct 2019 15:14:34 +0000

Hi,

I have a 14 Ram 1500, which already has a factory installed remote starter. I'm looking to switch over to Fortin, and use a MyCar RFLink. Can you suggest which product/products i could use to make this work.

Thanks!

Jesse

OEM Remote will not unlock/lock car after remote start

Sat, 19 Oct 2019 23:46:14 +0000

When I remote start my 2016 Hyundai Tucson with the OEM remote (3x lock button) I am unable to use the remote to unlock/lock the vehicle and have to use the phyiscal key to open the door. There are previous questions about this, but I have not found an answer yet. Is it a programming option or did I wire something wrong?

OEM remote on Evo one

Thu, 26 Sep 2019 02:41:42 +0000

Will the oem remote work for my 2006 Silverado with a evo one or do I need to get an antenna and remote for it

Alarm works when door is opened

Tue, 10 Sep 2019 09:49:19 +0000

1-OEM Alarm goes off when I unlock and open the door in kia sportag 2015 Standard key, EVO One.

2- Lighting around the key entrance no longer works

Will the OEM remote work to unlock door after the remote start is engaged

Tue, 15 Jan 2019 16:25:04 +0000

After installing a EVO ONE remote start on 2018 Toyota Tundra, I couldn’t unlock the door with OEM remote, had to do it manually,is there anything else I can do to make the locks work after engine is running?

15 Mazda CX-5 Evo one remote start, one oem remote works the other oem remote does not

Sun, 02 Dec 2018 10:35:28 +0000

Programmed the suv, started it with the remote.

2012 Subaru Forester Manual Trans. Evo-One OEM key fob

Mon, 22 Oct 2018 05:55:37 +0000

2012 Subaru Forester Manual Trans. Evo-One OEM key fob.
setup according to #54711 guide, except hood pin is not used.
Flashed to 79.49 & 1.24 ran the decrypter, then set the standard settings in both tabs. 83.2 C1 & D5 enabled
When I press the lock 3x times the horn beeps, the parking lights flash 3 times the radio & Dash lights flash. but it does not start. In reading the help guide, it says the EVO-One red light should turn on, it does not.
Any help would be much appreciated.

cannot lock the door or unlock the door when the evo one is activate

Sun, 21 Oct 2018 18:27:14 +0000

I have an Honda civic 2017 push to start manual. I have installed the evo one. i didnt connect the parking light to the car. i have programmed the evo one with the flash link for the version of my car at the moment, i think its the version 73.27 (if it can help i have installed the fortin evo one in november 2017) and didnt touch it after that. Also i dont use the T-harness i plugged every wire to the car directly like in the installation guide.

My problem is : i can activate the remote start. but when i leave the vehicule and when i press my OEM remote to lock the door it does nothing, the car still running. i need to open the door and press the brake pedal to close the car. so i dont know why the door lock doesnt work.
ive tried to buy the evo start to control my car with my cell phone. so i have installed the evo start in my car, i programmed everything and when i try to lock the door with the app it doesnt work too. i tried to start the car, but still do nothing.

I did not plug the wire for the lock/unlock with the car (cause i dont really know which wire is it) and i dont know if its really my problem cause i read the can bus should do it.

is anyone know what is my problem, cause i cant figure out what is the problem ?

thanks in advance.

The car does not unlock from OEM key after remote starting; I have to unlock door w/ key in order to gain access to car.

Tue, 18 Sep 2018 20:02:25 +0000

Hello!

I have purchased a Evo One / T8 Harness and installed it on a 2015 Toyota Corolla.

The car does not unlock from OEM key after remote starting; I have to unlock door by inserting w/ key in order to gain access to car.

Any idea what this could be?

Thank you

Stefan

2013 F150 w/ factory remote start. Wanting to add SmartStart with existing EVO

Sun, 12 Aug 2018 23:21:19 +0000

Remote start question...

Currently using the Fortin remote start with a Viper SmartStart module. However, considering swapping over to the FORD remote start to gain the use of the climate control features that it brings...

Don’t want to use the Ford version of Smart Start.

Anyone know if you can use the SmartStart module from Viper with the OEM remote start by Ford? Could the EVO be used as a bypass? Or connected to the OEM remote start. Would this work by disabling the EVO remote start and allowing it to work with just using the “OEM remote monitoring”?

Haven’t really had much luck digging on the net for the answer.

I was able to turn all the menus on, activate OEM remote start, etc as a check in advance of buying the ford module. I had previously successfully swapped the LCD cluster into my truck.

Details....

-2013 F150 STX 5.0 SC

-OEM remote start w/ Viper VSM300

-using Fortin EVO As remote start moment.

2006 Cadillac CTS using unprogrammed GM remote with EVO One

Sat, 11 Aug 2018 23:26:16 +0000

I have a 2006 CTS that has unprogrammed remotes. SInce it costs a lot to program them (special tool), I am looking into adding a different system for lock/unlock as well as adding remote start. I'd like to use a newer GM remote that has the remote start button vs having to press the lock button 3x. Is this possible? If not, can I use my existing remotes or will they still need to be programmed to the car?

Does the OEM works normally when installing RF642W or FTXDUO with EVO-ONe

Wed, 06 Jun 2018 11:50:19 +0000

Does the OEM works normally (locking and unlocking doors) when installing RF642W or FTXDUO with EVO-ONE in Mazda CX9?

or does it become inactive?

Evo-all stand alone sur cherokee 2014 clef avec oem remote starter

Wed, 04 Jan 2017 21:40:14 +0000

Jai quelques bogues sur cherokee 2014 clef. Il y a un demarreur d'origine. Jai installé un evo-all autonome avec rf kit. Desfois il ne part pas, desfois il part et éteint. Tout ca intermittent. Il peut bien aller 2 jour ou boguer 4 fois dans la journee. Avez vous deja vu des bogues avec le demarreur d'origine? Sinon, est ce que je serais mieu d'utuliser un E400?

Merci

Ground while running wire has a constant 12v reading

Sun, 27 Dec 2015 15:53:27 +0000

After installing a Prestige APS787E alarm w/ my Evo-All bypass module on my 2012 Nissan Rogue (Non-Push2Start), my lock, unlock & trunk buttone on the aftermarket keyfob work but the remote start doesn't work. I updated my Evo-All to the latest firmware & hardware available & flashed it to D2D protocol.

I also programmed the Prestige alarm using the install guide to get the Tach signal via D2D mode. But when I attempt to follow the "Tach rate progarmming" section of the manual, it is clear the alarm might not be getting a tach signal.

Is it possible to hardwire the tach signal to my alarm while using data mode w/ the Evo-All?

Secondly, I test the "ground while running" wire connection btw the Evo-all & Prestige alarm with a multimeter and I get a constant 12V even when trying to remote start. Is this normal? I thought it would/should give me a 0V or ground signal when I attempy to remote start the car.

Lastly, also just noticed that my Prestige key fob arms the aftermarket alarm but locking my doors w/ the OEM Nissan keyfob doesn't. Thus when I arm the car w/ the Prestige keyfob & unlock & open the doors w/ my Nissan key, the siren goes off. Is this normal?

Thanks in advance