Questions & Answers - Recent questions tagged programming-issue

why does my evo all keep going to red

Wed, 20 May 2026 22:27:07 +0000

my oem remote does not work durring install i have to press prograaaming button to complete and it goes red.. i need my flash link reset again. i do have rf kit 411 but havent got that far yet

2023 Toyota Corolla evo one doesn’t go past step 5

Sat, 07 Feb 2026 18:07:11 +0000

I am at step 5 of the Programming Procedure on a 2023 Corolla with key. I get through step 4 and the blue light will flash and then turn solid but when I start the car for step 5, the blue light stays on solid and the red light does not come on the install pretty easy and straight forward.

does the model 34-0793-2 affect win module replacement programming

Mon, 27 Oct 2025 11:15:52 +0000

i have a 2009 dodge ram 1500 i replaced the win module on and programmed it. it worked for 1 day then it stopped working would i have to program the evo all as well and how come my original keh fobs dont work with the evo all

New EVO-ALL won't pass step one for programming

Sun, 13 Jul 2025 19:43:20 +0000

Brand new unit EVO-ALL won't pass step 1 for programming. All three lights flash in sync (not alternating) Do these units ship without any firmware?

why does my programming procedure not go beyond the third step on my 2021 toyota sienna Hybrid?

Tue, 21 Jan 2025 03:03:52 +0000

I cannot complete the programing seven steps I spent two days checking connections and reconnecting making sure everything is right I even soldered the wires to make sure they are making good contact but seams that the module its failing> would you be able to help me?

EVO-One with THAR-TOY16 Programming stuck at step 7

Sun, 28 Jul 2024 22:25:15 +0000

Hi Fortin support team:

Vehicle: Lexus RX350h 2024 (Hybrid vehicle)

EVO-One GUIDE: #116181 Rev:20240513

Firmware: both 88.33 & 88.34

EVO-One S/N: 002B04659051

Programming stuck at step 7: The BLUE LED will not turn OFF, The RED LED will not turn ON.

Unable to add RFK942.

What should I do?

Stuck on Step 4

Thu, 04 Jan 2024 06:44:09 +0000

2012 Nissan Rogue Intelli-key using T harness NIS 2. I cannot get passed step 4. The yellow light never flashes it doesn't change at all after pushing button any amount of times. I went through the troubleshooting guide and I don't have power on yellow wire, I also reversed the can-bus wires which didn't help. The fob was placed 40 feet away inside the house next to the spare keys we have for this vehicle.

programming

Sat, 30 Dec 2023 16:29:34 +0000

intalling EVO CH5 on my 2009 Chrysler Sebring. When i go to progam it to the vehicle i press the black button and plug the black connector with igition off. All 3 LEDs flash at the same time and will not go to just blue like it says it is supposed to program. I cant find the trouble shooting section to find answers

programming issues s/n 002B04273087

Mon, 27 Feb 2023 19:34:56 +0000

once decripted, all i get is a solid amber light when reinstalled and the key is on. unit will not let me into any typeof programming. no remote or function. I have no conformation from the antanna or parking lights. it will however make the interior lights blink once i have started it with the key and i push on the brake.

I am using the nis2 T harmess and the rf remotes.

2010 ford escape KEY-OVERRIDE-ALL

Tue, 17 Jan 2023 20:09:09 +0000

I'm installling the KEY-OVERRIDE-ALL with a DEI remote start.

When I attempted to program prior, I would see the LED start flashing, but programming didn't complete.

Now when I attempt to program, the LED on the module stays on and the security light on the dash flashes rapidly.

I've confirmed I have 12V on Red, Ground on Black, Ignition on Yellow, and remote start staus on Blue.

Is there anything else i should try on this module? The module was purchased new in December and hasn't been installed in another vehicle.

Why won't my Evo-One move past step 4 on programming?

Tue, 10 Jan 2023 04:30:30 +0000

I have verified the correct firmware, proper voltage on yellow wire A1, and correct can-bus wiring.I have constant 12v with a good ground. When I turn the ignition to run the blue led that is supposed to flash 10x's turns off. I installed accordind to the install guide provided through fortin's website.I have followed the troubleshooting guide and get stuck after confirming all 5 steps

The first 3 steps in the programming are very straight forward. If you cannot pass these steps verify the following:
1- Firmware: Ensure you have flashed the correct firmware to the module as indicated in the installation guide.
2- Power & Ground: Verify the module is receiving a constant 12 volts and has a good ground.
3- Yellow Wire (A1): Verify this wire is on the correct ignition wire. Their should be 0 Volts present during the first 3 steps.

If the Blue led does not flash common issues would be the following:

1- Yellow wire (A1): Not connected to correct ignition source.
2- Can Bus Wires: If these are reversed or connected to the wrong can bus wires the module will not program.

2017 Ford Focus Programming Issues

Mon, 26 Dec 2022 16:31:36 +0000

I am having some difficulty programming my EVO-All FORT4 with my 2017 Ford Focus. The T-Harness is all hooked up, and the device has been flashed with the correct module. When I attempt to pregrade both keys, nothing happens when I press the program key at the end of the sequence. When I attempt to program a single key, it doesn't change from red to yellow. Any and all help would greatly appreciated.

During programming on step 14 guide 65601 only redlight flashes not red and yellow

Mon, 19 Dec 2022 14:35:28 +0000

It flashes 5 times

2017 EvoOne with TharFor3 T harness, blue light won't blink on programming

Thu, 25 Aug 2022 15:33:16 +0000

Thank you in advance for any help! I am a long time using of the EVO ALL and have done a few EVO ONE. A bit stumped on my 2017 F150 though. Using EVO ONE with the THAR FOR 3 harness.

All plugged in. Following wiring diagram for the A1 and A16 (put them together) on the white 20 pin connector.

When I go to program it, I can't get it to "blink blue". Therefore, I can't get any further in the programming procedure.

Followed the directions in the Guide. What could I be missing?

Joe

F150 2012 programming

Wed, 17 Aug 2022 21:05:44 +0000

I have a f150 2012 i done every thing 100% In the programing phase I made every thing i enter the first key after the second key and after the first key then the blue and red started flashing after that only the blue led appeared and the still on without the key but if i unplugged the red connector the car turn off please can you help me in the programing

EVO-All won't pass Red Light on programming (Step 5)

Tue, 19 Jul 2022 15:03:46 +0000

I've flashed the EVO-All multiple times using both the wizard and Pro versions of the flashlink. No success. I essentially flash the module and it won't program past step 5 where the red light is supposed to turn blue and flash.

No clue where to go from here.

I'm using the T-Harness as well so there's no direct wiring.

Programming 2012 fj cruiser solod red light

Sun, 13 Feb 2022 16:03:20 +0000

I have everything properly wired for the 2012 fj cruiser and I programmed the module on the computer. When It comes to plugging in the module the light is solid red like it's supposed to be but when you turn the key to the on position it just stays solid red. Maybe someone can reboot my module with the s/n?

2012 fj cruiser programming

Fri, 31 Dec 2021 14:54:19 +0000

I have everything wired correctly with the harness. I plug module in light stays red like it's supposed to but when I put the key to the run position it stays solid red and doesn't flash like it's supposed to

2011 Ford Escape red light stays on during programming - SOLVED

Mon, 27 Dec 2021 17:42:57 +0000

Vehicle: 2011 Ford Escape

Evo All #001A07260304 installed with T-harness THAR-FORD4; plug-n-play install, teed connections to ignition switch, immobilizer antenna and OBDII connector; no wires spliced

Can't get the unit to program. Process: Hold program button, plug in data cable and release on red light. Insert key and turn on until theft light turns out. Remove first key and insert second. Turn on for 3 seconds, theft light goes out, turn off and remove. Last step says to press and release programming button within 5 seconds (this is where it gets stuck). Red light should flash 10 times and blue light should flash 10 times and ignition comes on and turns off again. When I press the button the last time, the red light blinks and just stays on.

I've tried the firmware downgrade listed in https://fortin.ca/en/qa/92073/faq-red-led-stuck-on . That link says to downgrade to v 0.99 but the lowest version for Ford appears to be 4.01. I flashed 4.01, power cycled in vehicle, reflashed v 71.52, unlocked settings and reset the unit. Still same results.

I've also tried testing the data bus. Hold button, insert data link connector, release button on blue light. Connected all other connections and turned key on. Blue light stays solid. Shouldn't it flash on data?

The yellow wire is not connected as it seems to be part of the T harness, but I've tested it for 12v on ignition and it is getting it. I don't have the valet switch or hood pin switch connected. What am I missing? I'm wearing out the plugs with all these connections/disconnections.

Red light stays on during programming and wont program the keys

Sat, 18 Dec 2021 01:12:17 +0000

I hVE 2008 Ford Escape. I installed the Evo all fort4 with the the t-harness. I have installed all connectors(1,2,3) and connected a relay to the lights as instructed in step 4. I plugged the black connector in while holding the button in and then let it go when the red light came on. I put in each key for 3 seconds each and then pushed the button in. It didn't start the vehicle. Red light stayed on teh whole time. It only blinked when I pushed the button in. What causes this and how can I fix it?