Questions & Answers - Recent questions tagged remote-start-not-working

Q50 not remote starting

Mon, 06 Jul 2026 04:12:34 +0000

i have a 2015 infiniti Q50

SN-002B04 759527

i installed the evo-one with thar-nis4 t harness and RF942 kit.

programmed, decrypted and reinstalled tested with oem keyfob worked great, than i programmed the 2 RF remotes, test again worked good 3 times then just stopped working. i can still unlock/lock with all 3 fobs. it will try to remote start, gets to where it should crank and nothing.

2009 Tahoe intermittent start from remotes

Sun, 03 May 2026 02:15:57 +0000

Evo all s/n 001A07 726606

Vehicle doesn’t always start under remote operation.starts fine with key all the time. Using rf kit 942

2009 Chevy Tahoe

system worked flawlessly but only once.

Fri, 10 Apr 2026 12:38:02 +0000

i have just installed my evo-one with the gm3 t harness, and 942 rf kit on a 2015 chevy silverado 2500hd with standard key and onstar. i got the remote start and locks to work during testing but after i buttoned up, being careful not to stress any wires, my locks are no longer functioning. the remote says it worked, i hear the relays clicking, and see the parking lights flash. if i try to start the truck it will successfully start and run for about 3 seconds before shutting down. i will get several flashes of the parking lights but then it will not try to start again. i have counted 2 and 4 flashes after a failed remote start and i have even seen "service theft detterent system" on my dash a time or two after a failed start.

Remote only work if I push switch to "ON" on my 2020 Toyota Highlander

Tue, 17 Feb 2026 02:05:08 +0000

Remote only work if I push switch to "ON" on my 2020 Toyota Highlander (non hybrid). please help.

I have evo all rf442

Evo All the car doesn't start

Fri, 13 Feb 2026 20:29:21 +0000

Hi. I installed Evo-All on the my Volkswagen Passat B7 2.0TDI 2013 year whith standard OEM key.I used the THAR-VW6 wiring harness. Firmware version 75.40. I trained the module on the car. Then the decryptor cenerated a code , all successful. But the car won't start with the OEM key fob. The relay in the module clicks , the red light comes on , then the orange light comes on , and the car radio turns on. But the engine doesn't start, and the dashboard doesn't turn on. I connect all the connectors according to the THAR-VW6 instructions. I didn't connect the wire to the brake pedal ( my car doesn't require pressing the brake to start ) I didn't connect the wires for the start / stop button, as I don't have that button. I used the lock/lock/lock combination to start the engine. Where should I connect the separate yellow wire ( yellow ignition) ?

2015 Audi Q3 programming issue

Sat, 31 Jan 2026 17:14:00 +0000

2015 Audi Q3 push to start.

Evo rs with t harness

Install is all complete. I get to step 9. The blue flashes rapidly, push ignition, everything starts to cycle, the lights flash rapidly then red flashes 3x and continues to flashes 3x. Tried many times and still get the red flashing 3x.

Checked all wires

My car start, then stop

Thu, 22 Jan 2026 02:20:29 +0000

I have a remote starter kit HONDA-SL3. It worked fine for a long time but now when I press to start my car (Honda FIT 2009) It start fine but after a few second it stop, and do the same start and stop one more time. with the brake light flashing a few time. And that's it. Could it be a wire that got disconnected or something. It look like the device don't know that the car started fine

Blue light remains blinking when taking key out of ignition

Sat, 17 Jan 2026 05:38:28 +0000

Hi, I bought a kit that had a Fortin evo one. The Thar-ty10 and the thar-toy2. I’ve installed it but I’m running into an issue after the programming. I can program it to the point of the blue light blinking but when I turn my ignition off and take the key out it continues to blink. I tried doing the remote start by pressing the lock three times but it doesn’t work. Any help would be appreciated. I have a Toyota Camry 2014 se with the G key

I went through all the programming, still no start. what is the problem?

Fri, 26 Dec 2025 00:30:09 +0000

2020 Silverado 1500 LT standard key.

Vice # 001A07 549816

Also, I have reached a limit on downloads, how do I get more?

Issue after prgramming RFK942

Wed, 10 Dec 2025 04:17:35 +0000

I installed the EVO-AUDT2 in my 2019 Audi Q7. Initially I did not have an rf kit so I was using my oem remote to remote start the car. And it worked perfectly. I then purchased the RFK942 and the RFA2A. Reflashed my EVO ALL with new setting to include the rf kit. After I program the RFK942 remotes and turn off the vehicle, all the lights (red, yellow, blue) on the EVO ALL flash for a few seconds and then turn off. Neither of the remotes work and my oem remote does not even work now. I have tried programming multiple times and all 3 lights on the EVO ALL just keep flashing for a few seconds after turning off the ignition and neither of the remotes still work.

Lexys rx400h , evo one lte, everything is hooked up, when i push to start the car nothing happens?

Fri, 05 Dec 2025 20:36:51 +0000

Lexys rx400h , evo one lte, everything is hooked , vehicle starts using the evo start app but shuts dpwn after a few seconds, option D4 for hybrid is active, flashed a few times, also INT-SL+ wont program, the light stays solig red when i hit unlock button , please help!

Why is my light staying blue when i install the input wire for input B on EVO-ALL (AUDI)

Thu, 04 Dec 2025 17:52:08 +0000

This is probably my 5th evo install. My first time for an older car.. I have a 2008 Audi A4. I purchased the Evo All for the remote starter install. I used install guide 85651... first thing i did was the software download. In the software download only thing I edited was i turned on Standalone function, which was off. Once i did the original download.... next was the wiring. I did everything that was in the guide for without data link: san data link... so, once I plugged the plug in plug B. then the rest of the plugs. It just turned Blue. There was no Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate. But with the blue light lit... I hit the remote.. it did everything like it was going to start the vehicle. Locked the door. Then I heard clicking coming from module like it was going to start but it didn't.. any suggestions. Your help will be appreciated.

Remote start doesn’t work

Sat, 29 Nov 2025 03:51:22 +0000

I installed a Fortin EVO-ONE with the THAR-HON3 T-harness on a 2016 Honda CR-V Push-to-Start.

The module programs correctly, Dcryptor completed successfully, and CAN functions work (lock/unlock, ignition status).

However, the EVO-ONE never outputs ignition during remote start. I get blue and red LEDs, but no yellow LED, and the vehicle does not enter accessory or ignition mode. The EVO also does not detect the brake pedal (no blue flash), even though the car’s brake system and ignition work normally.

Please somebody help me figure out this problem.

Thank you

Programming successful, will only work one time.

Tue, 25 Nov 2025 20:57:08 +0000

After going through the programming, I installed back into vehicle and it worked the first time. I took it back to the computer, saved new settings to module. Reinstalled back into vehicle and it started the vehicle once again. Will not start vehicle again.

Will Evo One all-in-one remote start work on 2015 Mazda CX-9 with turn knob to start?

Sat, 13 Sep 2025 23:19:22 +0000

Hi, Will Evo One all-in-one remote start work on 2015 Mazda CX-9 with turn knob to start? My 2015 Mazda CX-9 does not need to insert key to start or stop, it has turn knob to start. is this consider stander key? how can i do KEY BYPASS PROGRAMMING PROCEDURE for my 2 key fobs, since it does not need to insert key? Looks like only stander installation is available.

Remote start keeps deprogramming from Evo one

Sat, 12 Jul 2025 17:46:19 +0000

Evo one with Evo start keeps deprogramming the remote start, I program the Evo one the be use as alarm and remote start the system works for a couple times then out of nowhere the system changes and only works as alarm, some how the remote start gets deactivated, I removed the Evo one and connected to the flash link in the computer the system shows that Evo one is working as alarm only, so I flashed the Evo one again to work as alarm and remote start then connect back to the car the remote start works for a couple times using the app then the Evo one goes back to work as alarm only, I tried many times flashing the Evo one again to work as alarm and remote but after a couple times working properly the system goes back to alarm only

How to program after getting new keys made

Wed, 25 Jun 2025 02:10:37 +0000

I broke my original key remote start was working with that key. Locks smith came out and made me two new keys and now remote start doesn’t work. 2008 Ford F-150 with the “Key Override All” and “FirstTech CM900” how to reprogram what’s in trouble shooter page 16 doesn’t work.

How to program Evo-All to aftermarket gsm remote starter through data-link protocol?

Tue, 29 Apr 2025 10:52:47 +0000

Hi, I have my Audi A5 2012 with Fortin Evo-all, and I'm trying to connect it to aftermarket gsm remote starter that supports Datalink protocol, almost everything works through it (Door lock/unlock, statues) but I'd doesn't remote start.

Could you please help me, how to program Evo-All, or what I have to do?

Original fobs stopped working after 1 -2 months after installation.

Wed, 02 Apr 2025 07:33:11 +0000

I installed a evo one standalone mode with no rf kit on a Honda crv 2012 and one by one both original fobs started to acting weird and now none of them are working anymore. What could the cause be?

Remote Start/Remotes Not Functional after Battery Disconnect

Mon, 31 Mar 2025 16:29:23 +0000

EVO-ONE, 04/2022, SN: 002B04 271047

2009 Subaru Forester

Remote Start program: 0.44 for Omega Remote OL-RF-42-SST

Everything worked as expected during programming and testing, but after battery ground/negative was disconnected and then reconnected (for ~2 minutes) there is now no response to any remote inputs. Unable to re-learn the remotes. Any suggestions to make this work again? Any way to prevent this from happening again?

2011 camry cranking, but don't start.

Sat, 29 Mar 2025 09:56:07 +0000

2011 camry cranking non stop, but won't start.

Everything is programmed.

Evo all.

Went through the the install and the car wont start and the key wont start it either?

Sun, 19 Jan 2025 14:51:39 +0000

Installed an evo-all on a 2014 buick verano. Installation was fairly easy. Thought it was flawless until my oem key wouldnt start the car. Also the key doesnt work to start either.

If your Cadillac SRX 2010-2016 suddenly stops starting

Fri, 17 Jan 2025 02:43:30 +0000

I searched and searched for similar cases on the Internet and found this one, written 4 years ago... I tightened these 3 bolts on the fuse board and everything was fixed... "The exact same thing happened to my SRX changed my headlight bulbs and put new battery in. Took the fuse box cover off and the relay out at front of fuse box as there is no room for my big hand to fit in. I figured that if i just removed the screws in the fuse box i could get some extra room so my hand would fit in to get the headlight bulb put everything back together. Went to start car dash lights came on would not start at all spent 3 hours trying to figure out what was wrong. My buddy came over as he worked at a GM dealer told me to push down on fuse box and the car started up the screws in fuse box where not tight as there is a wire harness under the fuse box ."

My evo duo remote stop working

Thu, 16 Jan 2025 20:40:22 +0000

I have a toyota corolla hatch 2020 manual transmission with fortin evo duo universal remote

the remote stop working recently

When i push lock unlock or start the led blink rapidly but the car do nothing

I double chek if the systeme was in valet mode but it seem not in valet mod...

It is possible to use the factory remote with a manual transmission for remote starting ?

The app doesn't work.

Wed, 15 Jan 2025 23:02:36 +0000

When I received a message from technical support regarding the fact that it is a remote operating device that I cannot update, they informed me that it would take 24 to 48 hours to be ready. I have a question: Does the device that works in the application, which is EVO-ALL-LTE, work?

2014 Cadillac SRX

Wed, 15 Jan 2025 00:55:49 +0000

Hello.The 2014 Cadillac SRX had an aftermarket remote start and evo-all installed. The owner wanted to install a GPS tracker and he removed the ground of the evo-all to connect it to the ground of the tracker.Since then, the car does not start. The ignition opens, but the engine does not start. The remote start elso has no feeling.

23 tundra 4x4 non hybrid push to start keyfob getting disabled temporarily

Tue, 14 Jan 2025 20:02:42 +0000

why is the evo one locking me out of using the doors/keyfob and not for a few minutes. When i tried to remote start using the keyfob i loose all keyfob functions cant start car and cant open/close doors or open tail gate. I also noticed no lights on the evo one while i tried to start it. I do have fortin evo telematics module selected which i havent ordered yet. will be getting the ascl7 instead the more expensive evo lte module. decryptor says completed succefully

All keys lost programed new fobs remote start cranks but not starting

Mon, 13 Jan 2025 23:39:23 +0000

Hired to do reprogram fobs 2014 infinti Q50 All keys lost reprogramed new fob all buttons work however now remote start problem car cranks but no start. Evo-all 2018, infiniti q50 2014.

tundra install issue now factory remote start dead

Sun, 12 Jan 2025 17:38:13 +0000

so i have a 23 tundra non hybrid that i couldnt get evo one to work and now factory remote isn't working.first off didnt want to pay 15/m for toyotas sub par remote start but i guess im going to have to now. i triple checked the wiring /splices prior to install so wiring was good. followed the procedures and all the lights during setup worked the dycriptor worked, but when i went to remote start nothing except my key fob temporarily stopped responding to doors and push button. so i went back and changed the setting to unlock door prior to start and nothing but key fob not responding no push button start. not knowing what caused it i removed it reconnected the pink wire and after a few min i could start the car and open/close doors. went in the toyota app subscribed to the remote connect and all is well except remote start is no longer working gives me a d5 error and to contact dealer. every thing else in car works just not remote start. so i connected my scan tool and now i get an u111787 lost communication with accessory gateway for bcm and special key did i fry the control module or did i break the pink wire in connector. like i said every other function works just fine only remote start ive installed the evo one multiple times in older cars with out a problem. im hoping when i take it to dealer its an easy fix like a relearn or something but i fear it will be an expensive fix

Autostart works only when the key is in the car

Thu, 02 Jan 2025 19:22:59 +0000

I installed EVO fort4 kit in my 2012 Ford Fusion. I used my two factory keys and programed them per the instructions. The auto-start worked for about two months. Now it will only start when I have the key inside the car ( it does not need to be in the ignition) The key works to unlock and lock the car normal. Can you tell me what I need to do to get it working again?

2015 LS460

Tue, 24 Dec 2024 10:19:13 +0000

Hello. I installed evo-one on 2015 LS460. 002B04697112...When we want to start, the ignition turns on instantly and turns off. What to do?

Remote start doesn’t pair with the car Audi SQ7

Thu, 12 Dec 2024 18:52:32 +0000

Hello,

I purchased an remote starter kit from Romania - Autoextra partner, after 3 days of working on it I had no clue how to make it work, maybe it will be easier to talk directly to you as support and not make a 3 way conversation.

Update how I’m now : everything is wired corectly (measured with voltmeter), made the connection to can high and can low in the left side of driver side next to the fuse box (2,6V can high; 2,4V can low) all wired up exactly how instructions are (green, orange/brown with the grey and grey/black from the module connector) and no success, ignition on and the blue led from module goes off and stays off till I turn the ignition off again, then solid blue led shows again. Software version is 61.28 (recommended from the windows program), I refuse to think that it can’t be a solution to make it work together. Maybe someone from tehnical support or software can discuss with me to find a solution, it will be faster via whatsapp if available or by email (I think that there is only 5-6 hours difference between us).

Kind regards,

Andrei Neacsu

2017 Ram 1500 Start briefly then shut off

Sat, 07 Dec 2024 20:03:20 +0000

Installed the fortin evo all with THAR-CHR7 and a 5706v w2w. Programmed according to instructions. Everything is working properly except I can't get the vehicle to remote start every single time. It starts and shuts off right after starting. Sometimes the truck will remote start and stay running like it should but not everytime. What could be wrong? Is it the firmware version?

2012 Civic starts then stops three times

Tue, 03 Dec 2024 10:54:26 +0000

Hello, I have had a remote start on my 2012 Honda Civic for 5+ years. It has quit working. It is a EVO-ALL and CrimeStopper RS00-G5. From following the troubleshooting I think it has to do with the tach signal but not sure what to check. The car will start for about 3 seconds then shut off. It does this three times and then nothing. While it is running the starter is engaged the entire time.

Signs of a decryption issue (Bypass) on a VW Jetta 2015

Mon, 18 Nov 2024 12:25:39 +0000

I have installed a EVO ALL on a Jetta 2015 TDI (Push Start - Automatic). I have the EVO ALL, THAR-VW1 and TB-VW installed as per instructions (I decided to skip the trunk release wiring as I didn't find the feature useful for me case). The EVO All is programmed with Diesel Option enabled and it went through the Decryptor without any issues. But when I press the 3 lock sequence. It doesn't start or crank. I see the red light turns on, and then the yellow light turn on... and it repeats this procedure twice (as per the options programmed). The dash of the car doesnt come on (as expected) during the sequence. I will check the brake lights when I have time but I was wondering if there is possibly something wrong with the bypass.

Thanks

Orange light blink 2 time

Fri, 15 Nov 2024 13:02:52 +0000

My starter was working very well with phone and by key.

Now, only key works. The orange light of the FMH antenna blink 2 time. It's impossible to connect by phone to the car.

I see in Manuel if amber light blink 2 time to disconnect and reconnect the antenna. When I do it, orange light blink 7 time. Then start again 2 time.

Do you know what I have to do to reuse my phone to start the car ?

2018 Tiguan will not start

Wed, 13 Nov 2024 20:25:03 +0000

2018 VW Tiguan, STD-Key, Not digital cluster, AT

EVO-ALL firmware 64.06

THAR-VW6

Decrypted and programmed successfully, but when trying to remote start via lock lock lock from oem key, car turns on, but doesn't crank.

Tested while in the car and the depress break light (shift lock) was still illuminated. I wired in the Yellow/Red Break Out to Black/Red VESCM (+)Foot Break correctly.

Tested command start while in the car and depressing the break, works.

Please assist.

2017 F350 Super Duty Evo all 1 key programmed successfully but won't remote start

Wed, 13 Nov 2024 14:41:53 +0000

Upon trying to remote start the red and yellow come on and blue blinks 1 time but not start. Stick key and turn forward, yellow light comes on. What am I missing?

2013 Chevrolet 2500 HD -Starts once then won’t crank

Tue, 12 Nov 2024 14:16:06 +0000

I have installed Evo All SN 001A07 468692 with T-Harness THAR-GM4 withRM942 remotes and MYCAR using hrn-11rs-01.

The factory remotes work as well as the 942.

The truck will start once using the remote start and then just light up and “click”. If I unplug the module it will work again.

From reading through the messages here I believe the issue is that I have flashed it too many times.

Any help would be great

2004 Ford explorer not seeing inputs from lock

Mon, 28 Oct 2024 23:04:48 +0000

I installed my EVO-One and was trying to program it to see the keys and this is when i first noticed that the evo was not seeing the inputs from the factory key lock and unlock, luckily i was able to get around it by starting the car with the key, and it accepted it, so further down the road i now have it fully programmed and installed, i turned on the feature that when you start the car and step on the brake it locks the doors, which it does, then when you shut the car down the doors unlock, which it also does, so the Evo is able to control the locks fully, but it is unable to see the command from the car, do i have to have a seperate remote because i really don't wish for that, am i missing something? like i said it sees the car start, it sees it shut down it controls the locks fully, but when i push the button the evo doesn't respond to the inputs at all. is it a setting that i messed with by accident?

13 honda accord push to start. Won't OEM remote start, automatic transmission

Fri, 25 Oct 2024 16:47:40 +0000

3x lock module shows blue light response to inputs from OEM key, electrical click and nothing. module shows yellow light when running started normally.

Thar-one-hon3, Evo One. Firmware 73.30, function 38:2 is on. Unit option C1, D2 and D6 are on, Yellow loop wire is cut on module

SN: 002B04680114

2015 VW GTI Manual, remote start worked once but now just cranks

Sun, 13 Oct 2024 23:35:43 +0000

Just finished installing an Evo-one LTE in my 2015 VW GTI, manual with push to start (mfg. in 2015) using the TB-VW and Thar-vw1 I had some issues with the first iteration of programming but eventually hard reset the Evo module, reflashed it, re programmed with R-link. Installed back in the car and the remote start worked! Buttoned it all up, got the car in ready mode just to test it and it just cranks, but won’t start.

my connections and programming were all fine if it started the first time so what would cause this?

2015 Dodge Dart Manual Transmission EVO ONE No Remote Start Following Installation

Sun, 13 Oct 2024 22:09:15 +0000

2015 Dodge Dart, Manual Transmission. EVO One SN 002B04248404 with both factory key fob (tip style) and Crimestopper Revo 4.1 Extended Range fobs. Installed using CHAR7 T harness.

Installed per guidelines. Seemed straight forward. Programmed Module using default suggestions. Decryptor appeared to work without error.

Was able to start vehicle using factory key fob. Performed manual ready procedure…. Brake pedal, E brake, removed ignition key. Vehicle continued to run. Exited the vehicle and closed the door. At this point was unable to get the vehicle to stop running. Vehicle’s dash did indicate when the door was open and subsequently closed. Confirmed all other doors and trunk were closed throughout the installation and testing. Hood groundout was wired but the hood remained closed and we confirmed the hood pin adjustment wasn’t grounding the module out.

In one attempt, we started the vehicle, performed the manual ready mode procedure, exited the vehicle, waited 20 seconds, and then using the Revo fob lock functionality was able to shut off the vehicle but still, click 3 unlocks or the factory keyfob or “start” on the Revo fob did not result in the car starting.

(8 hours later……)

After multiple attempts and rechecking the wire harness for correctness, reviewing the question and answers info on Fortin, and praying to the “Remote Gods”, we gave up.

Any advice? Also… help me understand how many times I can reset the module and run the decryptor application. In an attempt to get this working, I think I performed the operation 4x’s.

I seem to remember you can brick the module if you run the crypto too many times. Then I read something about as much as you want within a 5 year of module manufacturing date. Please clarify this. I certainly don’t want to “brick” the module.

Regards,

Rob

update: Confirmed that the EVO One module cannot be "bricked". Worst case scenario is that it has to be reset by Fortin Support, but that it can be reprogrammed manytimes (at least for the same vehicle) manytimes without losing it's functionality.

Have been able to get the car to run after removing the key from the ignition, but have not been able to get the car to shutoff when closing drivers door as indicated as a step or procedure in the "Manual Ready Mode Manual". Was able to get the vehicle to shut off via the start option on the aftermarket Revo 4 FOB, but that seemingly put the vehicle out of "ready mode" status as it would never allow for a successful remote start.

Still scouring for answer as to why the vehicle will not shut off on its own when exiting the vehicle thus remaining in "ready mode" and allowing the remote start functionality to work properly.

3x remote flash won't start

Sat, 12 Oct 2024 17:32:21 +0000

2004 Chevrolet Suburban 1500, I've been having issues for 3 months now. I replaced brake switch twice, wire harness for brake switch, and still the same issue. If I unplug the brake wire from EVO-ONE, it would remote start. If the wire is plugged in, no start. This started after 3 years of module use, nothing changed. Now, EVO-ONE is doing a 3X light blink when trying to remote start, which is ready mode disabled. It's an automatic transmission, it's in Park, no parking brake on, still nothing. Last week I was able to bypass the brake switch with a separate switch to solve the other remote start issue, but 2 days later it's doing the ready mode disabled. I'm about to give up, rip this thing out and try a different brand.

2015 Forester (push to start) , shut down immidiately after remote started.

Sun, 22 Sep 2024 17:15:29 +0000

2015 Forester (push to start) , shut down immidiately after remote started (after 1 or 2 second), what im missing here?

2015 Corolla, flashes 4 red flashes & 3 red flashes

Wed, 11 Sep 2024 01:11:37 +0000

I have a 2015 Corolla with an automatic transmission start button.

Installed with THAR-TOY6 T-Harness & EVO ALL

The device flashes blue when opening or closing the doors, but when trying to operate it with the remote, it flashes 4 red, I keep trying to program it and it gives me 3 red flashes.

SN:001A07261560

Flash blue once before red flashes

Please see the attached video.

https://photos.app.goo.gl/6rfod5uAwRBQ7MgUA

Chevrolet spark 2020 push to start remote not responding to remote start

Sat, 10 Aug 2024 10:18:04 +0000

The Evo all-GM6 device was installed and programmed, but the remote that was programmed in the steps does not start the car with remote start, and the remote start only works with the other remote

Evo one can't function product

Wed, 29 May 2024 03:16:56 +0000

Hi sir I have install evo-one in my Kia sportage 2014 can't function all try ready u key bypass programming ready same no function

2020 Toyota Corolla sedan will no remote start

Mon, 27 May 2024 23:34:38 +0000

So basically I had it working for a couple years already and now I went to add a rf kit and it won’t remote start.

I’ve reflashed, followed the instructions to a tea and had zero issues but won’t remote start.

I try 3 times lock and the hazards just flash a 4th time and nothing happens

EVO-ONE: car starts, then stops, hazard lights flash 3x, then starts, then stops finally

Mon, 27 May 2024 00:19:08 +0000

Hey everyone! I'm using an EVO-ONE with T-Harness for the 2020 Kia Sorento PTS. When I do the 3x lock, the car turns on, then stops after a few seconds, flashes the hazard lights 3x, then turns back on, then stops after a few seconds with no hazard lights flashing.

Any help would be great, thanks!