Questions & Answers - Recent questions tagged standardkey

2025 Impreza standard key guide available?

Sun, 28 Dec 2025 23:43:05 +0000

Is there a remote installation guide for 2025 Subaru Impreza? I see that there is a guide for 2023 model, but I am not sure if it will work.

Thanks!

Is there t-harness available for 2018 Outlander Sport standard key?

Tue, 17 Jun 2025 09:59:17 +0000

Is there t-harness available for 2018 Outlander Sport standard key? Thanks!!!

2017 Impreza orbit one Evo-All came in car used

Thu, 20 Feb 2025 12:46:18 +0000

Bought a used car with “Orbit One remote starter & alarm & bypass module”

Starter Vr: 7.1.21 , Evo-All Vr: 4.18

Serice No: 002B07 323505

Was bought without a remote start key, wondering if I am able to program a new key, or remove the entire system and have done by dealer

2018 Jeep JK Manual Transmission

Sun, 26 Jan 2025 11:31:15 +0000

Hello,

Does anyone have an actual diargram that shows the connections from the relay to the clutch switch? Or a personal step-by-step you may have used. Before I cut factory wires I would like to be sure. I have both the EVO-All and EVO-One with the CHRT5 and CHRT7. Th

2009 forester manual transmission

Sun, 08 Dec 2024 07:13:19 +0000

Instructions for the Evonne don't call for it but why is the emergency brake, brake pedal not wired as well. And what happens if the car is left in gear?

2017 F350 Super Duty Evo all 1 key programmed successfully but won't remote start

Wed, 13 Nov 2024 14:41:53 +0000

Upon trying to remote start the red and yellow come on and blue blinks 1 time but not start. Stick key and turn forward, yellow light comes on. What am I missing?

EVO One with THAR-GM1 V2 in 2016 Chevy Cruze Limited Manual Transmission

Tue, 22 Oct 2024 10:59:04 +0000

Hello all,

I am getting ready to install an EVO One Module as a remote starter only, with a THAR-GM1 V.2 Harness in my 2016 Chevy Cruze Limited, with Flip Key and manual transmission. The wiring diagram only shows the Pink wire from the High Power (6 Wire) Harness being used. Does that mean I don't have to hookup the other 5 High Power Wires, or are they required for the unit to function? I haven't been able to find any wiring schematic for where the wires (aside from power and ground) hook up in my car. I guess I am unlcear on whether or not the GM Harness renders those other 5 wires unnecessary.

Thank you in advance.

2020 camry

Sat, 23 Dec 2023 15:01:46 +0000

Hello. I installed evo-one on a 2020 Camry (002B04337440). Everything works, the parking lights don't come on. What to do?

2020 Chevy Silverado 3500 Standard key?

Mon, 04 Dec 2023 18:09:36 +0000

Is there available products for a 2020 standard key chevy silverado 3500? i have an evo-all and a gmt-7 harness but cant find any literature?

Issues with lock/disarm unlock 2011 jetta standard key manual transmission

Wed, 11 Oct 2023 12:08:50 +0000

When following install guide #61521 for manual transmission on 2011 jetta it shows the blue/red connection off of BCM plug A connected to the green/red of the evo-all module, this function is not working all other parts of the install are functioning except for unlock/disarm. Is there a solution to this issue?

Evo-all thar -vw3 standard transmission 2011 jetta

Wed, 04 Oct 2023 19:22:06 +0000

Can the evo-all be installed using the thar-vw3 and tb-Vw in a manual transmission 2011 jetta as a bypass/interface module with a separate starter? If so is it the same wiring connections show on the thar-Vw3 with the exception of the brake vs the clutch bypass difference in the automatic vs manual wiring for the evo all.

why do the factory keyfobs deprogram after installing evo one in a 2011 subaru imprezza with standard key?

Tue, 03 Oct 2023 11:38:16 +0000

I installed an evo-one (no t-harness) in a 2011 subaru imprezza, standard key.

after programming and install, the factory remotes deprogrammed and would not work. I had to start the car on both keys to reprogram them.

The same thing happened three days later.

Programing evo-all in 2013 Escape

Sun, 27 Aug 2023 16:03:12 +0000

Trying to install an evo-all with the thor-for1 t harness into a 2013 escape with standardkey start. Just want the remote start feature. Evo module came from my sons infiniti g37x. It has been reflashed with flashlink to be installed in the escape. Concerning that the flask status bar never goes over 25% beofore it "comepletes" the flash.

The module will not program to the car. With the standard 2 key programing, when I get to step 8 and press and hold the program button, the vehicel never starts and the bule and red leds come back on solid. If I try the Dcryptor medthod, with either key, the red led never goes out and yellow never comes one durring the key cycle steps. if I just plug the module in w/o holdong the program button, all the leds flask as if the module is not programed.

As the thor-for1 did not come with a C plug, I took the ones from the infiniti harness. however I do not have a A plug either, but not sure that is needed...?

Use Evo-one in a vehicle with no transponders.

Sun, 21 May 2023 19:04:05 +0000

We have a 2014 E-250 it was ordered as a commercial build specifically without a transponder. I am interested in installing an Evo-One in it for remote start and security. Will it work without having the bypass programmed as it is not necessary. Would I need to install a different firmware on it?

2023 Forester w/key is Evo-One with T-Harness truly plug n play NO cutting splicing anything??

Sat, 08 Apr 2023 13:07:18 +0000

Last vehicle i did was 2011 Nissan Juke and even with T-Harnes etc I still had to splice a few wires etc.

Is the 2023 Forester simpler ? I still see some type of cutting the imobilzer wire??

Will 3x oem key work??

My still having the flash tool should help keep cost down yes??

Is therea way to program with only 1 key

Fri, 24 Feb 2023 20:08:08 +0000

Chrysler Pats 04 + , requires two keys to program, customer only has 1 key . Am I able to program with only 1 key?

Key fobs won't program evo one installed in a 2013 kia soul

Fri, 03 Feb 2023 19:55:42 +0000

2013 kia soul, automatic w/o immobilizer. When entering programming I get the flashing blue light on the antenna but can not get the solid confirm light.

Chevrolet colorado 2006

Fri, 03 Feb 2023 12:05:59 +0000

GMC TERRAIN 2017, won't start unless key is n the vehicule, config. num.1 used

Wed, 11 Jan 2023 12:12:16 +0000

Hi! I programmed the EVO ONE number of times, went through the decryptor process with success, yet, the car won't even try to start unless the key is in the car. checked my wiring over and over again, yet, can't find any info on the subject in the previously asked questions. Is the decryptor failling miserably, or the evo one I'm using is defective. Currently going crazy over here. help?

2010 Sierra Standard Evo-All THARGM4 No Alarm Functions

Wed, 28 Dec 2022 22:41:13 +0000

Programming was successful, vehicle starts, door locks continue to work via factory remote. Evo-all seems to be monitoring door switches as it will shut down if a door is opened when locked. However no alarms sound whether that's the factory alarm or evo-all. What could be the problem here? I was looking to supplement the factory alarm with evo-alarm for shock/glass break sensors. I'd settle for just the factory alarm working again.

t harness eve-all with standard key Camry 2011

Wed, 28 Dec 2022 18:23:24 +0000

the wiring diagram in guide does not match colors for camry 2011, does the t-harness work with evo-all?

2011 Ford Fusion Standard key, only blows cold air after remote starter installation

Wed, 16 Nov 2022 14:38:58 +0000

I installed evo one remote starter on the 2011 ford fusion s, i hard wired all the wires, did not used t harness, but after installation, i was getting only cold air from the vents with starting from remote, i can change the blower speed. couldnt change the vent modes and the air temp.

if I start it with the key, heat blows only for couple minutes and it switch back to cold air it self, and has to restart the car to make it blow hot air for another couple minutes. any idea what could be wrong here,? any help will be appriciated,

2013 Rogue with standard key will not remote start

Tue, 08 Nov 2022 11:50:22 +0000

I bought this Rogue used with the the Evo-All and Pursuit Pro9776C remote starter installed. It worked perfectly for a week or so then stopped. Now when locked, remote starting will trigger the alarm. If it is unlocked with the remote, it starts the start sequence and all lights on the dash light up and the doors do an unlock sequence, but then nothing. I can leave key in the barrel and disconnect all but red connector on the Evo-All and it will go through the start sequence 3 times and it will start for a secord or so and shut down. I have successfully made sure that the tach sense is working properly. What other connections should I take a look at?

2016 Chevrolet Malibu standard key Evo One

Tue, 18 Oct 2022 18:00:20 +0000

Hi guys. Do you know if there is any solution for the 2016 chevy malibu limited flip standard key? It happens that all the connectors match the 2015 connections but the colors do not. I would like to install an Evo one with RF kit. I've been looking on the website but I don't see anything for this car specifically. Any recommendation? Thanks.

2019 Nissan Versa Note no transponder

Mon, 19 Sep 2022 17:55:39 +0000

Hi, My problem is related to both of these forms and i cant seem to get the car to start i have followed both of these guids and im still not being able to get the car to start I have the option A3 turned off. I am using the RFK 912 remotes to start the car in which they are both programmed. I have tried holding the program button until the blue lights come on. Plugging all the harness in, in both instances either pressing the program button and not pressing the program button. Either way I'm still not being able to actually get the car to start. The remotes are sending a signal and confirming but no status lights no dash lights nothing from the evo. The big connector is plugged into the back of the ignition barrel it's the giant plug with those 8 giant silver contacts The obd is plugged in. There is no transponder for the car so I didn't use that harness. In the flash Manager under pro mode in the remote starter tab I have tried options 2.1-2.4 to see if that makes a difference. None of them have made a differenceAm I missing a step?Update: After changing setting C1 I was able to remote start the car via the OEM remotes but not the fobs. The remotes are the rfk912 they are acknowledging the antenna by demonstrating a green light both on the remotes and on the antenna but they are not starting the carHere's is the serial number: SN 002B04252984 https://fortin.ca/en/qa/94079/2013-nissan-versa-standard-key-no-transponder-evo-one?show=94079#q94079https://fortin.ca/en/qa/93425/2016-versa-note-std-key-no-transponder-unable-to-program-evo-one?show=93425#q93425

2019 Nissan Versa Note Transponder wire

Mon, 19 Sep 2022 16:56:59 +0000

Hi, I have spent countless hours trying to find the white 4 pin connector that is shown in the diagram that is shown to be connected to the ignition barrel. There seems to be no connector of anytype except for the one on the back. I am referecning to the image shown on page page 2 step 2

https://fortin.ca/download/79331/evo-one_ig_thr_bi_nis5-versa-note_2014_key_a_79331.pdf

2009 Rx8 Key preogram

Tue, 24 May 2022 09:07:50 +0000

Installing cm900 with evo all on a Mazda RX8 atomatic standard key, evo won't program correctly. Try with 1 key and 2 still the same. Everything lights up but no cranck. Aso change protocal to Fortin still those the same thing. Not sure what I'm missing.

Thank you

removed this kit now car wont start with key

Tue, 22 Feb 2022 17:50:54 +0000

ok i am an installer at 12 volt solutions in tulsa oklahoma, and we installed one of your evo all kits in a 2016 ford escape, and couldnt get any power to the module so we removed the kit and plugged it all back up factory and now as soon as you turn the key to accessory it tried to start, and when you try to crank it over it does nothing. All the lights and the radio come on but wont start.

2016 nissan versa, can't find a guide for a non transponder key.

Fri, 21 Jan 2022 14:14:16 +0000

Evo one, thar-nis5 kit.

Remote start only works the first time

Wed, 29 Dec 2021 22:05:39 +0000

Remote start works the first time but not after that solid red light only

Subaru Legacy will not remote start

Sat, 11 Dec 2021 12:14:03 +0000

I have a 2016 Subaruy Legacy Limited with key start. The EVO-1 with T-harness worked fine. After hitting a deer and vehicle being repaired(all body, no mechanical repairs), it does not remote start.

Press lock button 3 times, the red light, then the blue light, then the yellow light comes on. Dash lights come on, parking lights come on, then all shut off. Parking lights flash 4 times, then reattempts starting, then same thing.

I removed the unit and updated with flash-link, still does not work.

I had read about valet mode adn pressing lock and unlock buttons to get it out of valet, nothing.

I read about no tach signal, but there is not tach wire on Evo-1 I read.

The unit is Service # 002B07 267043

I know I am overlooking something, I just cannot see what it is.

THANK YOU!

Can't get into the car after remote-start

Sat, 04 Dec 2021 08:05:57 +0000

Hello, I purchased a second-hand Subaru WRX STi 2017 (manual, normal key) with Fortin Evo-one(?) installed and FTXDUO remote control. Remote start works ok (thank you for that - a great product!). The only problem is that after remote start I can not get into the car - buttons of original key do not work. If I press Unlock button on FTX, the car unlocks and then locks up immediately. I have to remote-stop the engine, only then I can use original key to unlock the door and get into the car. Something must be missing here, but what? Or am I doing something incorrectly?

2008 GMC Sierra 3500HD remote start works good but now the key will not start the vehicle

Fri, 05 Nov 2021 12:20:06 +0000

I did not hook up any additional wires only the harness is this maybe the issue?

romete key connot progrsming after press 4x the brake or use valet switch and presshols engine will start

Sun, 10 Oct 2021 13:10:33 +0000

kia 2012 maunal standard key

Lexus RX350 2009 Firmware in Manual is not an option in Flashlink Manger 4

Sat, 05 Jun 2021 23:47:35 +0000

I have Flashed the INT-SL+ with 0.17 via the instalation manual Guide#90081

It says to load Firmware 79.65 to the EVO-ONE. The highest option available is 79.56.

I cannot get he INT-SL+ to program to the car via the lock button.

The EVO-ONE will learn the key and flash red 10x, but when I go to the next step to hold the programming button on the INT-SL+ then connect connector 1 and keep holding while connecting connector 2. The Led is supposed to light up, but nothing happens.

2020 kia optima key to start, no vehicle info for this car.

Mon, 15 Mar 2021 22:36:29 +0000

I have a kia optima 2020 key to start. Theres nothing for this vehicle....... only push to start and mine is key to start.

2009 GMC Sierra Manual Door Locks....Can you turn of the unlock detect on an Evo-All?

Thu, 11 Mar 2021 16:21:59 +0000

I installed the GMT4 in my GMC Sierra that has manual door locks. The truck shuts off when the key is inserted into the ignition because there is no unlock pulse. Can I turn of that feature on this system? I also have the RFK411 installed with the evo all.

2009 GMC Sierra shuts off as soon as the key is inserted into the ignition. Evo all with t harass install.

Fri, 05 Mar 2021 22:10:16 +0000

Remote start fine but engine turns off as soon as key is inserted

2016 Kia Soul. Remote start isn't engaging. Fortin Evo One

Fri, 26 Feb 2021 17:47:11 +0000

Having problems with the Evo One not kicking the remote starter on. Programming was did right Im assuming, the can connections are correct assuming becuase i was getting the flashing blue led and such when programming. I do not have the EMS wire so i did use option 2 in the installation diagram. Hit the oem remote 3 times but nothing. Not sure what needs to be checked in the firmware updater though. Kinda stumped and help would be appreciated.

EVO-ALL or EVO-ONE for a 2016 Kia Soul Standard Key?

Thu, 28 Jan 2021 20:49:02 +0000

From doing a little research it seems that the EVO-ALL does not have the remote start? Thanks for any help.

Can you start the Jeep with just your key?

Tue, 05 Jan 2021 17:50:35 +0000

Have the evo one all connected and works fine with the 3x lock. But when I tried to start it manually with the key it will not start.

EVO-ALL Not Pairing With CAN BUS

Mon, 28 Dec 2020 16:48:40 +0000

Hello All;

I'm having difficulty getting the EVO-ALL to correctly pair with the CAN Bus. Per the troubleshooting guide, I did double-check each connection and tested the voltage. I believe I have an unbalance pair CAN1 connections. One connductor tests at 4.5 and the other at .5. Per the guide, I've tried to cycle the vechile thorugh its functions, e.g. Start, Stop, Seats, Mirrors, etc but I can't get the CAN1 conductors to measure at 2.5. See troubleshooting guide below:

Any ideas?

Thanks!

NOTE: In some cases the can bus wires will fall into a single wire can system and this may prevent the module from programming the can bus. Meter the can bus wires one at a time. They should measure roughly 2.5 Volts DC per wire. If you have one wire with 4.5 Volts and the other is .5 Volts the module may not program. Stop programming and start the vehicle with the key or pts button, put the vehicle through its functions such as the radio on/off, door locks,electric seats, etc to try and balance out the can bus wires. In some cases you may need to drive the vehicle to get the Can Bus to balance back out. Once you have done this re test the can bus wires to ensure they are roughly 2.5 volts per wire.

2007 Elantra won't program can

Thu, 10 Dec 2020 10:09:36 +0000

I am installing a Evo one remote start in a 2007 Elantra with T harness no immobilizer. After setting the module to Blue and connecting the A1 and C1 harness and turning the ignition on to start programming step 4 - 5 the blue LED does not flash. I have followed the trouble shooting steps and have verified, Yellow wire A1 is correctly connected to pink ignition wire+, the can bus wires are correctly connected to gry/black can low to yellow (pin14) on the DLC and gry can high to white (pin6) on the DLC. I have verified can voltage high at 2.6 and can voltage low at 2.4, I have tried to balance the signals closer to 2.5 but I am unable to make a significant or stable change from those readings.

2016 Civic with key doesn't always start.

Tue, 08 Dec 2020 17:14:38 +0000

2016 Civic with regular key using evo-all(sn 001A07 159806) and avital 4115L. Sometimes it doesn't start after sitting for 20 minutes or so(doors locked, factory alarm on). It will just crank. Dash lights come on as normal. Will start on 2nd attempt. Doors unlock on 1st attempt to disarm alarm. Starts fine with key. Any ideas?

2020 Hyundai Elantra standard key no remote start

Fri, 04 Dec 2020 11:26:26 +0000

2020 Hyundai Elantra standard key no remote start.

using fortin model evo-one

Bypass firmware 76.59

Remote start 1.25 firmware

Hardware inside 7.0

THAR-ONE-KHY2 harness.

There is no pats wire to hook up. CAN high and low hooked up yellow automatic transmission wire cut for Automatic. Used suggested options. Did programming for blue light option 2. The blue light comes on steady. when plug in main harness. Plug in the CAN wire connector and plug in 20 pin connector. Turn ignition on and blue light flashes rapidly. Turn the ignition off blue light goes out. Try to remote start on the facotry remote push the lock fob button 3 times and no remote start. Tried option 20.2 and no luck, based on some search here on the forum. Any advice thank you

Can I install EVO-ALL alone on Audi A6 2006 with standard key ?

Mon, 16 Nov 2020 22:45:31 +0000

What is "SPECIAL INTERFACE" that is REQUIRED FOR REMOTE STARTER INSTALLATION?

Fiat 500 cant link remote start

Thu, 29 Oct 2020 20:11:15 +0000

I cannot link the remote. The valet antena flashes when I plug it in the module, but the blue led doesnt react with ignition on. Nothing happens in any scenario while trying to program the remote. It starts fine with eom remote. Help!? Evo-one

2012 Kia Soul standard key rf641w not unlocking and locking vehicle

Tue, 19 May 2020 13:05:11 +0000

2012 Kia Soul standard key no immobilizer. Using thar-one-khy1. I am using the tachless mode. I have programmed 2 rf641w keys successfully, however they do not unlock and lock the vehicle properly. I even tested the wires to ground to verify ground control and that was better than the module was doing. So here's the behavior:

Lock: will not work unless I lock the car with the oem remote period. making me think the evo module is storing status incorrectly or is unaware.
Unlock. Works if I press the unlock button 3 times
- I have also tried adjusting option 8 for this with no luck. (unlock pulse adjustment)
Kill start - I am unaware, but is there no feature to kill the remote start and turn the vehicle off via the remotes?

Thanks in advance.

2012 soul standard key no can bus communication evo one

Mon, 18 May 2020 08:43:08 +0000

2012 Kia Soul standard key no immobilizer. Using thar-one-khy1. Blue light won't flash when programming. I can read codes and voltage to the fortin module white 5 pin matches obd output at around 2.37v low can and 2.67v high. Module,flashlink all at the latest firmware. Evo one flashes successfully. Just when key on it fails to finish programming. Also wired in the fortin hood switch. Any help? Since it's such a simple install it's embarrassing to ask for help. Should work and great instructions as usual.

Car wont start remotely

Tue, 11 Feb 2020 11:43:00 +0000

Finally got past step 5. Module is now programed but wont start with the remote, nor wil the doors unlock or the tailgate, if the doors are loked they will unlock. no lights on the module light up when attemptin a remote start. Double checked the wiring, all is good