Questions & Answers - Recent questions tagged step-7

EVO-ALL, 2017 Infiniti Q70, unable to get past step 7 (standalone with T-harness)

Tue, 25 Feb 2025 19:24:07 +0000

On step 7, brake pedal press turns on blue and red led, shortly after, red led does not stay on and turns off, only blue led stays on, unable to continue on to step 8.

S/N: 001A07 670775

EVO-One with THAR-TOY16 Programming stuck at step 7

Sun, 28 Jul 2024 22:25:15 +0000

Hi Fortin support team:

Vehicle: Lexus RX350h 2024 (Hybrid vehicle)

EVO-One GUIDE: #116181 Rev:20240513

Firmware: both 88.33 & 88.34

EVO-One S/N: 002B04659051

Programming stuck at step 7: The BLUE LED will not turn OFF, The RED LED will not turn ON.

Unable to add RFK942.

What should I do?

EVO ALL - 2012 Audi A4 Step 7 flashes red 3 times

Fri, 12 Jan 2024 22:17:18 +0000

I am in the process of installing this and I get to step 7 and it is supposed to be solid red then in step 8 red and yellow alternating. At step 7 after Blue red yellow alternate it goes to 3 red flashes over and over. What could be causing this?

2012 Lincoln MKS Step 7 programming issue, red light goes out when both red and blue lights are to be lit

Thu, 28 Sep 2023 16:28:53 +0000

Upon pressing the brake for step 7, the red light and blue lights are lit, but the red goes out prior to pressing the ignition button. It seems the bypass won't program. When finsihed, and trying to remote start, the car says no key detected. Ideas>

Why am I getting 3 red LED blinks after step 7?

Sun, 02 Feb 2020 23:19:52 +0000

UPDATE: I plugged everything in and gave it a try. Car starts right up but dies immediately. Gives me the "no key" alert. dcryptor process will not complete for some reason.

2013 Passat standard key, standalone install. EVO-ALL (2/2019), THAR-VW2, and TB-VW (1/2017).

Guide 62471

SN: 001A07 008702

Flashlink Firmware: 75.39

TB-VW wired into brown transponder wire.

I have all of the harness installed as directed but when I start the dcryptor programming, all goes beautifullt until the end of step 6. When I release the programming button, I don't get the rapid 3-LED alternation. The red LED just continuously blinks 3 times. I've even tried resetting the

Solid red light does not turn to blue for step 7

Sun, 15 Dec 2019 23:36:01 +0000

have triple checked the wriing and I have 12V supply. Can High and low both 2.5V. Still when programming the module it doesnt get past step 7 with a solid red light not going to blue. Have pulled the key in and out numerous times while waiting for the lights on the dash to go out and still stuck. Anyone have any a answers that could help out?

Unable to get past step 7 but step 7 works BLUE/RED LED on

Fri, 25 Jan 2019 08:19:45 +0000

Firmware is the latest all setting are as per the manual

Step 7. Cannot get blue light to illuminate

Sun, 01 Jul 2018 15:56:29 +0000

All steps until 7 no issue

Remote Started But..

Tue, 06 Feb 2018 03:31:50 +0000

I just finished installing and programming the EVO-NIST1 as a standalone on my 2016 Juke Nismo PTS. When I got to STEP 7, I pressed on the brake and red + blue LED lit up. Red LED only stayed on for 2 secs and blue LED remained on. I tried it multiple times and got the same result. As I continue to program, everything works as the guide described. Should that draw any concern?