Questions & Answers - Questions récentes dans la catégorie: Dodge

Request for CAN Wiring Diagram – Start-X Kit (Dodge Challenger 2015–2017)

Mon, 23 Feb 2026 19:02:57 +0000

I recently purchased a Start-X remote start kit for my Dodge Challenger 2015–2017 from Amazon. After opening and installing the kit, I discovered that some wires are missing — specifically the CAN bus harness that connects from the OBD-II port (pins 6 and 14) to the module.

I contacted Start-X support, and they kindly offered to either send the missing harness or replace the kit. However, I have already shipped the kit overseas, so returning or receiving replacement parts is unfortunately not a practical option for me.

While researching, I found a Chrysler wiring document that explains the module side (white connector) CAN wiring, which was very helpful. The missing component appears to be a 2-pin CAN connection from the OBD (pins 6 & 14) that transitions into a 5-pin CAN connector going into the module. https://cdn02.fortin.ca/download/97651/evo-all_ig_rts_bi_chr6-7-300_2011_pts_b_97651.pdf

I would like to build the missing harness myself, but to do so safely and correctly, I need the wiring diagram or pinout configuration for the module.

Module Serial Number: 001A07 682508

Could you please provide the CAN pinout diagram or technical guidance for this specific module so I can fabricate the harness properly?

Thank you very much for your assistance.

THE CURRENT MODULE CANNOT BE FLASHED ANYMORE

Mon, 23 Feb 2026 18:45:47 +0000

I was trying the flashlink firmware and playing around, I pressed the Dcryptor tab multiple times without actual flashing, after a while I got the current module cannot be flashed anymore.

SN: 001A07 682508

2026 Dodge Durango

Fri, 23 Jan 2026 18:09:54 +0000

New vehicle 2026 Dodge Durango is firmware available? Only see firmware/software for 25 Dodge Durango can this be used on 26 model yr?

Reset please decryptor limit for EVO ONE SN:002B05 017438R

Mon, 01 Dec 2025 12:24:44 +0000

Reset please decryptor limit for EVO ONE SN:002B05 017438R

2003 Dodge Neon Evo All

Tue, 28 Oct 2025 22:36:35 +0000

Hello,

I just purchased an Evo- All and I swear it showed as being compatible with a 2003 Dodge Neon (non-srt). I went to flash the module and wire up my remote start unit, and only saw the SRT model in Flash Link. Does anyone know if this module will work on the non-srt model of the Neon, or should I get something different?

does the model 34-0793-2 affect win module replacement programming

Mon, 27 Oct 2025 11:15:52 +0000

i have a 2009 dodge ram 1500 i replaced the win module on and programmed it. it worked for 1 day then it stopped working would i have to program the evo all as well and how come my original keh fobs dont work with the evo all

Will the Pats Chrysler 04 transponder start my 06 Dodge Dakota,

Thu, 23 Oct 2025 13:03:22 +0000

Purchased this truck and owner said the remote start was removed, I found the Transponder and Antenna is on the windsheild, If this will start my truck do you have the instructions or do I require something else. Vehicle did not come with a transmitter just the two keys

thanks

I need a reset to add remotes. evo all 6 - 001A06 542823

Mon, 24 Mar 2025 23:24:50 +0000

need to add rf442

CANNOT GET EVO ONE TO WORK IN OLDER DODGE DAKOTA

Wed, 19 Feb 2025 23:30:34 +0000

Tried installing an EVO ONE module in my 1993 Dodge Dakota. Manual Transmission. Got all necessary wires connected, module will power on, and allow me to program one remote. Afterwards, it will not respond to anything. The antenna LED will not come on, the module lights would alternate red, yellow, blue. Got the flashlink, updated the module, same thing. At a loss, any help appreciated...

Starter kill relay wiring for a 2015 dodge Durango with a fortin evo one with thar-chry7 t harness

Wed, 19 Feb 2025 00:06:58 +0000

Starter kill relay wiring for a 2015 dodge Durango with a fortin evo one with thar-chry7 t-harness

EvoCHRT5 on 2006 dodge ram 5.9

Mon, 10 Feb 2025 22:51:33 +0000

2006 dodge ram 2500 5.9 diesel

I have evo chrt5 and updater only thing I’ve done is connect yellow on 20 pin to yellow on t-harness and green/red on 20 pin to purple on t-harness and my truck is still the same but the evo has no power can anybody help me

dodge journey 2016

Sat, 01 Feb 2025 10:57:13 +0000

journey 2016 evo one avec chr-7 guide 109611 tout bien programmer le camion part 1-2 fois a distance ensuite ignition allume mais ne demarre pas bouge le module et tout va bien ensuite merci j ai mit la derniere version

SKIM Removed

Fri, 24 Jan 2025 17:26:26 +0000

I have a 2004 Dodge Durango with the SKIM removed. The factory key fobs no longer work because of this. I want to Install a remote starter EVO-0ne with the RFK441. With the remote start work, and will the lock and unlock buttons on the RFK441 work?

DBall2 compatibility

Thu, 19 Dec 2024 08:33:30 +0000

Hi,

I have a DBall2 in a dodge caravan 2015. Are the recent LTE and RF remote compatible with it ? Or does the module needs to be replaced with a EVO-ALL for that ?

Can the lte be use with an RF remote ?

Thanks

Ben

How do I Dycrpt?

Sat, 14 Dec 2024 14:04:04 +0000

I did the first part of connecting the module to my 2013 dodge journey and now I am having trouble dcrypting it. Everytime i Go to decrpyt it it says no data found. I did see that we werent supposed to change the viechle even if it wasnt our own. I read it too late and already changed the viechle to the journey. What should I do?

04.5 dodge ram 3500 5.9 Cummings

Fri, 13 Dec 2024 01:31:39 +0000

What do I need to install remote start on my truck and is there a t-harness that will work with my truck for easy installation?

What color is the + starter in 2007 Dodge Caliber

Thu, 12 Dec 2024 17:16:26 +0000

I already installed a remote starter in 2008 dodge caliber with evo all. Right now im trying to install a remote starter into a 2007 dodge caliber which this one doesnt have a + starter wire. Even in the instruction given it says that "if present". I connect all the wire correctly but it doesnt work. The dashboard is light up when i press the lock 3 times but its doesnt start up the car. Do i need to connect the + starter? Can someone please help 2007 dodge caliber Automatic Evo all with thar-chr5

EVO-CHRT4 Preload module - Still need FlashLink ?

Thu, 28 Nov 2024 14:30:50 +0000

Hi,
Like it was say on web site EVO-CHRT4 is preload

Is it still necesary to make the part of installation with the FashLink?
Thank you !

06 Dodge Ram evo-one with t harness remote starts then locks and shuts off

Mon, 25 Nov 2024 01:06:20 +0000

I have an evo-one with t harness on an 06 ram, having an issue where it’ll start then lock the doors and it’ll shut off then my dash and everything will stay on as if it’s running, if I unplug it and plug it back in it’ll start again then die after relocking the doors then unplugging it and plugging it back in it will let me start with the key. Will provide firmware and review settings tomorrow to see if I have something set wrong

2005 Dakota No Remote Start

Sun, 17 Nov 2024 16:30:05 +0000

EVO-CHRT5 RS with T-harness. Using as stand-alone remote start with oem remote. A1 connected to Ign 1 & A15 connected to grounded hood switch. When inserting 20 pin connector blue light goes out, comes back on when key is turned on to continue programming balance of programming seems OK. After remote is programmed yellow light stays lit. Do get blue light & horn honk on remote activation but no attempt to start.

2015 Dodge Dart Manual Transmission EVO ONE No Remote Start Following Installation

Sun, 13 Oct 2024 22:09:15 +0000

2015 Dodge Dart, Manual Transmission. EVO One SN 002B04248404 with both factory key fob (tip style) and Crimestopper Revo 4.1 Extended Range fobs. Installed using CHAR7 T harness.

Installed per guidelines. Seemed straight forward. Programmed Module using default suggestions. Decryptor appeared to work without error.

Was able to start vehicle using factory key fob. Performed manual ready procedure…. Brake pedal, E brake, removed ignition key. Vehicle continued to run. Exited the vehicle and closed the door. At this point was unable to get the vehicle to stop running. Vehicle’s dash did indicate when the door was open and subsequently closed. Confirmed all other doors and trunk were closed throughout the installation and testing. Hood groundout was wired but the hood remained closed and we confirmed the hood pin adjustment wasn’t grounding the module out.

In one attempt, we started the vehicle, performed the manual ready mode procedure, exited the vehicle, waited 20 seconds, and then using the Revo fob lock functionality was able to shut off the vehicle but still, click 3 unlocks or the factory keyfob or “start” on the Revo fob did not result in the car starting.

(8 hours later……)

After multiple attempts and rechecking the wire harness for correctness, reviewing the question and answers info on Fortin, and praying to the “Remote Gods”, we gave up.

Any advice? Also… help me understand how many times I can reset the module and run the decryptor application. In an attempt to get this working, I think I performed the operation 4x’s.

I seem to remember you can brick the module if you run the crypto too many times. Then I read something about as much as you want within a 5 year of module manufacturing date. Please clarify this. I certainly don’t want to “brick” the module.

Regards,

Rob

update: Confirmed that the EVO One module cannot be "bricked". Worst case scenario is that it has to be reset by Fortin Support, but that it can be reprogrammed manytimes (at least for the same vehicle) manytimes without losing it's functionality.

Have been able to get the car to run after removing the key from the ignition, but have not been able to get the car to shutoff when closing drivers door as indicated as a step or procedure in the "Manual Ready Mode Manual". Was able to get the vehicle to shut off via the start option on the aftermarket Revo 4 FOB, but that seemingly put the vehicle out of "ready mode" status as it would never allow for a successful remote start.

Still scouring for answer as to why the vehicle will not shut off on its own when exiting the vehicle thus remaining in "ready mode" and allowing the remote start functionality to work properly.

my computer canot detecect evo all in one

Mon, 15 Jul 2024 09:58:00 +0000

cant finish decrytor

my computer canot detecect evo all in one

Mon, 15 Jul 2024 09:56:28 +0000

2019 dodge journey cant finish programing decoder

Limit reach

Fri, 03 May 2024 03:55:18 +0000

Can I get my flash limit reset? SN # 001A06 554531 R

Searching for a better diesel module 07 ram 2500

Fri, 26 Apr 2024 20:59:03 +0000

Looking for a module for 2007 ram 2500 diesel that has adjustable crank and wait to start times.

Initially installed the evo all with t harness. It doesn't have an option that waits long enough to start, also cranks too long making the starter drag.

What do I need to let the EVO-RS9 on 21 Challenger 6-speed manual acknowledge a pressed clutch pedal for remote start?

Sat, 10 Feb 2024 16:36:20 +0000

Everything sets and works fine. I can stay in the car and activate the remote start, it will go through all the steps twice, but no start. If I stay in the car and do the same steps, the car will start as soon as I press on the clutch pedal.

will fortin evo RS CHRT5 start my truck without purchasing a after market remote starter

Mon, 29 Jan 2024 12:31:14 +0000

will fortin evo RS chrt5 start my truck without purchasing after market remote starter

no blue lights when programming oem key

Mon, 29 Jan 2024 12:27:30 +0000

programmed and wired correct, no blue lights comes on during final step of turning ignition on with oem key

2008 dodge ram 2500 diesel

no blue light when switching oem key on during setup

Mon, 29 Jan 2024 11:58:14 +0000

blue light does not come on with oem key during setup

Late 2023 Durango Headlight Switch Connector FYI

Wed, 17 Jan 2024 14:10:41 +0000

The later Durango (mine is 8/2023) has a different headlight switch connector than earlier models as shown in install guide. It does have a white/brown wire that does change with switch position. Will the Evo-All have any problems with this connector change?

Is there an option for remote start for a 2005 ram 1500?

Thu, 11 Jan 2024 20:49:59 +0000

I only see bypass options wondering if evo one could be used for this vehicle.

MODULE LED'S DON'T DO ANYTHING WHEN PLUGGED INTO VEHICLE

Mon, 25 Dec 2023 18:18:56 +0000

USED FLASHLINK, MODULE HAS CORRECT FIRMWARE, PLUGGED INTO VEHICLE CORRECTLY, HELD DOWN BUTTON AND ATTATCHED 4 PIN CONNECTOR TO MODULE, NOTHING HAPPENS. NO LED'S LIGHT UP AT ALL. evo-all standalone

2015 Dodge Charger will not remote start

Sat, 18 Nov 2023 05:27:05 +0000

Hello. Referring to this guide I have set up my EVO-ALL

Here is what I have done:
- Flashed the unit with the latest firmware
- Selected my vehicle in the flashlink software
- Connected the T harness and ignition wires

When programming:
- Let go of programming button on BLUE
- Press programming button once to turn off BLUE
- Turn ignition to RUN
Now the BLUE led starts flashing. According to the guide, the RED led should also be flashing, which it is not. That leads me to believe that CAN2 is not being detected, is that correct? How do I fix this issue?

EVO-ALL ,CHRT5, 06 Dodge Ram with RM-441 Lock , key FOB unlock feature not working. Remote start works fine.

Thu, 26 Oct 2023 09:33:00 +0000

Installed EVO-ALL on 2006 RAM 2500 Diesel using CHRT5 in standalone mode. OEM key works with 3-lock remote start. Added RM-441 remote kit and updated settings with flash updater. OEM key still works. RM-441 will start the truck but not lock or unlock. Lights flash red or blue on EVO when pushing the buttons. Do I have some setting wrong or is it required to hardwire the purple and pur/wht wires to something and if so to what?

D1 options grayed out after running decrypter

Sun, 13 Aug 2023 22:16:28 +0000

001a07197935 also when plugging into decrypt I have a solid red light

I got everything to work except I can't get it to turn off with remote or phone app

Please reset Evo All Service# 001A04 069253

Tue, 01 Aug 2023 01:07:50 +0000

I want to use the Evo All for a 2006 Dodge Charger. Please see if the limit can be reset.

Flash reset

Mon, 24 Jul 2023 09:01:53 +0000

n 001a07197935 flash limit reached

Flash limit reached SN 001A07 363152

Sat, 20 May 2023 18:55:18 +0000

Can you please assist with the flash reset. Have had issues programming it with my RF kit and it's keeps coming un-synched with my tach.

Will it unlock/lock if I use a smartphone add on?

Tue, 25 Apr 2023 22:26:59 +0000

Eco-chrt4 on a 2011 grand caravan. If I use a smartphone add on module will I be able to lock/unlock the vehicle using the app? Asking since I noticed that it's only connect to can-low can-high through the ignition using the T-harness

Evo one CHR4 dodge challenger 2010 no any action only security light flashing

Tue, 07 Feb 2023 16:45:48 +0000

2010 Dodge challenger SRT with stander key and manual transmition

Module programming okay

blue light flash every press lock

Remote start red light one and give 2 sound then off

dashboard securty light flashing

Evo one with Chr 4 T-Harness

please help

connecting the wires A1 and A16

Tue, 13 Dec 2022 13:06:57 +0000

I have ordered evo-all unit and connected it as stated at the guide Guide # 97611 page 5/13 (wire-to-wire). After I finished the connections and the programing, and finally connected the unit to the flashlike lite for CRYPTUR. Everything was going-on according to the steps in the guide without any problem. Then I connected the unit back to my car, and I remotly started my car by pressing the lock botton three times, and everthing was good until now, but then I noticed the following:

1- the secondary ligths and the tail ligths of the car become on even thought the ligth switch was on (off state), and the head lights never work when I dial the switch to the low beam and high beam state.

2-After I started the car remotely and I get inside the car and I press the push-to-start button of the car to shut the engin off, it shuts off then re-start again without any action from me, but if I open the door after that it shut the engin off.

3- If I press the lock button of the keyfob three times after I was started the car remotely, it shut engine off normally without re-starting again like what happened with me when I shut it off by the push-to-start button of the car.

4- I followed the wiring connection step by step, but I didn't connect only A1 and A16 wires to any where they still lose, do I need to connect them and where?

Evo-All will not program

Sun, 04 Dec 2022 21:17:05 +0000

I have a 2006 Dodge Ram. I hooked up the evo-all with the t harness and made the 4 connections at the ignition switch, I have triple checked all the connections they are hooked up to the correct wires and have verified that they are getting connection but when I start to program the module I hold down the button while pluging in the data connector and stop on the blue light, I then connect the other connectors but when I do the next step which is turning the key on the blue light goes out, when i turn the key back off the blue light comes back on. I have used the flash link and verified that everything is set up correctly and has the latest firmware. I think this is the step that is supposed to be programming thru the can bus, Any ideas would be very helpful

2005 Dodge Dakota ABS, Traction Control And Check Engine Lights After Install

Wed, 30 Nov 2022 10:56:23 +0000

ABS, traction control and check engine light come on every time you remote start it. Everything works fine when you start it normally. Code is U1120 - Lost Wheel Distance Message.

Change Connection location of CAN high and CAN low

Tue, 29 Nov 2022 09:39:08 +0000

Is it ok to change the location of connection for the CAN high and CAN low wires from where I should connect them as shown in the guide to the OBD II

No response from OEM Lock on EVO All with all T-harness

Fri, 25 Nov 2022 13:35:30 +0000

2014 Dodge challenger

After successful Programing including DCryptor process. EVO-ALL does not respond to OEM Lock and doesn't start engine. Installed with T-harnesses for ODB2 and Push Start Button.

Any help is appricated.

Unable to get passed step 7, All LEDS lit expecting yellow only

Thu, 24 Nov 2022 17:12:56 +0000

I am programing a EVO All for a 2014 Doge Charger. I was able to program once and was unsuccessful Dcryptor process. So I have been trying to re-program but I am allways stuck at step 7, Once the Unlock button on the fob is pressed all LED light(Blue,Yellow,Red) but expecting just yellow. I have tryed multiple times.

Any help is appricated

Thanks

All leds light up on step 7, Expecting just yellow

Thu, 24 Nov 2022 16:59:25 +0000

I am unable to get passed step 7 for a 2015 Dodge Charger. I was able to run through it once but faild runing the Dycripter. So I am attempting to re-program again. Every time I try I always get all three leds lit steady (Blue,Yellow,Red).

Any help is appricated.

My EVO ALL unit never reachs to step-6- of the programming steps in FORTIN guide #97611

Tue, 22 Nov 2022 23:43:41 +0000

I connected my evo all unit according to the wiring diagram that I already downloaded from the website, then when I started the programming procedure, also according to the steps in the guide #97611, everything was going on normally until step-5-, then the unit never move to step-6- ( after I press and release programming button (in step-5-) the blue LED goes off and never return back flashing). I repeated the procedure one more time but I reached the same step and the unit never moves to the next step.

My unit SN:001A07 283796

2008 dodge ram 3500 diesel standard transmission

Sun, 06 Nov 2022 01:16:43 +0000

2008 dodge ram 3500 6.7 cummins with a manual transmission, I've installed the evo one with a t harness. The module programs properly, but when I press the lock button 3 times to start the module clicks a few times but does nothing.

vehicle will not stay running

Tue, 01 Nov 2022 17:57:40 +0000

sometimes the truck will not stay running when trying to remote start i have the rf kit aswell. when it happenes it doesnt matter which i use the rf or they factory fob the truck will try to start then shut down a second after firing. ive updated firmware performed factory reset and am still having the issue. everything is installed correctly by the book supplied by yall. to temporarily remedy this i have to unplug the unit then redo the holding down the programing button syncing both fobs which get rather annoying. when it happens the red an orange lights will come on while the blue light very faintly flashes the truck will try to fire then when it shuts off the blue light will flash. then the yellow light will become solid after a second the blue light will flash again and then it resets and tries to start again. also the security light on the truck will flash not sure if thats normal or not. i would like a remedy to this issue other than to keep reseting it every time which defets the purpose of having a remote starter.