Questions & Answers - Questions récentes dans la catégorie: Ford

2016 Ford E450 6.8L V10 6R140 transmission, is there a solution for this vehicle?

Thu, 25 Jun 2026 12:55:45 +0000

I'm wondering if the F series products will work since no E series are listed?

Which Module do I Need for a 2018 Ford Mustang Manual Transmission

Wed, 10 Jun 2026 14:53:12 +0000

Which Module do I Need for a 2018 Ford Mustang manual transmission?

Evo All not recognizing request to lock or unlock from aftermarket starter

Thu, 04 Jun 2026 18:31:32 +0000

For my 2014 Ford Fusion, looking to use the Evo All FOR3 to receive signals from a module to lock and unlock my doors. I'm using a wire to wire connection, and tested the signal at the 20 pin connector to the evo, and it's receiving the negative pulse from the aftermarket module to lock and unlock, yet nothing is happening.

When using the setup wizard on the updater, I'm advised to use firmware 4.01, and when using pro to adjust locking settings if that's necessary, I'm advised to use firmware 71.57, though I'm unable to complete the programming process with the latter firmware. The blue led does not flash rapidly when I turn the key to on, just stays solid blue. Does anyone think they'd be able to help with this?

Gracefully,

How to renew expired activation key when you just purchased the product.

Sat, 23 May 2026 15:52:28 +0000

Activation key came expired and used. Cant install my product

Hi, do you have solution for Ford Escape 2025 ?

Wed, 11 Mar 2026 00:53:31 +0000

Hi, do you have solution for Ford Escape 2025?

2013 Ford Fusion 1.6 Manual - Clutch bypass pinout

Sat, 28 Feb 2026 18:48:53 +0000

Hi,

Does the evo one support manual mode for the a 2013 fusion manual? Need the pinout from the bcm to bypass the clutch switch for remote start. Does it need to be driven by a relay? Also will the evo one detect the electronic handbrake via CAN? Can I use the t harness and then wire in the bypass separately?

Problems loading firmware

Tue, 17 Feb 2026 10:03:08 +0000

I'm trying to flash firmware 4.01 onto an EVO-ALL for a 2016 Ford Fusion to program it using Wizard Mode for a single key. The software freezes and never lets me flash the module. Is anyone else having this problem? How can I fix it?

Can I use EVO-ALL with Viper Remote Start and Keyless Entry?

Tue, 17 Feb 2026 04:25:53 +0000

My mother has a 2013 Ford F150 and I am going to put a remote start in it. I have one already that I am planning to use. It is a Viper 4103XV. I obviously need an immobilizer bypass module as well. I am just trying to find out if the EVO-ALL would work in this setup. I have an opportunity to purchase one from a friend for a good price. Thanks for your help!

2015 fiesta 2 key programming ,red and blue light won't flash and programming wont go further

Mon, 02 Feb 2026 01:12:05 +0000

checked wiring , everything looks good

Evo one and dsm550 extended runtime

Fri, 30 Jan 2026 05:11:06 +0000

The smartstart pro app gives me the option of extending the remote start runtime by another 15 minutes. However, my truck still shuts down after the original 15 minutes. How do I fix this?

How to select mode with RFK912 for EVO-ONE function programming?

Thu, 08 Jan 2026 03:02:18 +0000

I have an EVO-ONE module with the RFK912 kit that's working great. Installed in 2008 Ford Fusion 3.0L SEL

I want to program certain functions (ex function #38, so i can change the remote start sequence from 3x Lock to Lock Unlock Lock).

There is NO guide I've found that shows how to select the Mode (1 thru 6) with the RM912 one-button remote.

For the 4-button remote, you select the mode as follows:

MODE 1 - LOCK
MODE 2 - UNLOCK
MODE 3 - START (3 SECONDS)
MODE 4 - FUNCTION (3 SECONDS)
MODE 5 - FUNCTION LOCK
MODE 6 - FUNCTION UNLOCK

So my question is: Whiile function programming, how can I select the mode with the RM912 1-button remote?

NOTE: FlashLink Manager V4 does not show any options other than A1-A11, B1, C1, D2-D5, and D6. I'm using flashlink lite adapter. Only the BYPASS tab is visible.

DSM 550 issue?

Fri, 02 Jan 2026 05:28:22 +0000

Im getting a 702 error communicating back to app. It will start,unlock,lock fine but doesn't communicate back to phone that any of the functions were successful. it is started.

Thar-For5 Connection Location

Thu, 25 Dec 2025 14:30:01 +0000

When selection my vehicle, it shows pictures for what looks like a different harness. I believe the photos are wrong for the vehicle.

Does anyone know where I install the Thar-For5 T-harness on a 2021 F-150 XLT push to start?

Thanks.

2014 F150 Install Assistance for Parking Light

Fri, 12 Dec 2025 23:14:42 +0000

I have a FOR1 T-harness and EVO-ALL and I'm trying to wire it up for the first time. I'm using page 6 of this document as my guide. https://www.wirecolor.com/download/94891/94891.pdf

I've tapped into BCM Passenger Kick Panel for Parking Light+, but I'm not sure what to do with this wire. Am I expected to bring my own relay? Do I double up the wire on the existing factory relay and then run a wire from the factory relay to EVO-ALL? I've never tapped into a relay, do people just pop it out and put wire alongside the pin as the put it back in or is there a way to use a posi-tap on the back side easily?

Ford remote start

Thu, 11 Dec 2025 06:08:07 +0000

Is it possible to install an Evo-All on a Ford like on a VW and a Juke?...With brakes and start-stop?

2018 Fusion

Wed, 10 Dec 2025 14:58:16 +0000

I installed Evo-All on 2018 Fusion. The car starts, but the interior heater doesn't turn on. Is this how it's supposed to be?

2020 f150 lock/unlock/lock option known issue?

Fri, 14 Nov 2025 17:26:15 +0000

Has anyone experienced this issue with the 2020+ f150 stand alone with t harness lock unlock lock?

The install is like 5 minutes and goes great. Test at the door l/u/l fires right up. The problem is as soon as you move away a few feet from door with key ....the vehicle lets you lock unlock the park lights come on and you cannot lock again until lights time out which isn't fast enough for remote start sequence. 3x lock works fine but you have the horn honk as usual. Has this happened to anyone else? Just wondering

My code isn't working I'm locked out of the schematic

Sat, 08 Nov 2025 20:26:15 +0000

Wire color code not working locked out of schematic

EVO ONE won't program key bypass, can't get it to hard reset.

Wed, 29 Oct 2025 17:41:16 +0000

I can't get the evo one to program my keys to bypass the pats system. 2006 escape regular key. I tried to reset the module back to factory settings but it won't reset. Could you reset it for me? SN 002B04 015937. Thank you

Is the remote start module required for EVOALL install in 06 escape

Fri, 17 Oct 2025 11:26:06 +0000

I have a 2006 Ford Escape that I am installing the EVOALL in. Do I have to have the seperate start module to install it? Or is the EVOALL a stand alone install?

Relay clicks 3 times when releasing brake pedal while driving.

Sat, 04 Oct 2025 04:52:15 +0000

When I release the brake pedal while driving I hear a relay clicking 3 times. This happens intermittently. Some days it happens every time I release the brake pedal, some days it doesn't happen at all. This never happened for years after the original install, but started happening a few months ago.

Installed on 2013 Mustang GT, manual transmission, with option 33.2 enabled.

EVO One with THAR-FOR1 t-harness.

EVO-ONE 2022 Ford Bronco Clutch Bypass

Sat, 27 Sep 2025 15:50:45 +0000

As per the title; has anyone completed or have any information, diagrams or guides on a clutch bypass for the Fortin EVO-ONE on a 2022 Ford Bronco.

2014 Ford F-150 XL Stand Alone Install No Power Windows/Power Locks

Thu, 25 Sep 2025 19:16:23 +0000

Hi Fortin,

I recently purchased a F-150 that was a bare bones truck meaning no power windows and no power locks. If I get the 2 Ford keys with buttons on key for lock and unlock, will it work with a evo-all and tharness 3x lock installation?

Not sure if this vehicle will still have canbus lock signals available to program the remote start or will the keyless entry buttons also work. Does the vehicle still have unlock and lock features the car came with only a regular key no buttons?

Or will i have to do the install and add a fortin RF kit?

What is the bare minimum that has to be connected for the EVO-ALL to work on a 2015 Ford Focus

Tue, 23 Sep 2025 00:31:02 +0000

If I hook up can- and can+ and pins A1, A10, A16, and A20 will the remote start function properly?

SN #001A07 696223

I saw a Carlink CLLRCC long range control snd wondered if its compatible with an evo one

Thu, 28 Aug 2025 05:32:53 +0000

I saw a Carlink CLLRCC long range control and wondered if its compatible with an evo one

Looking for a product to bypass Pats lost key

Sun, 17 Aug 2025 20:26:41 +0000

Looking to by something to bypass the pats system. Lost key, replaced ignition and the transponder ring multilevel times with no luck

2017 f350 2 keys programing not complete

Thu, 31 Jul 2025 20:26:18 +0000

i am installing evo all in the truck ford f350. 2 keys programing , i went through all the step fine until step 9 the blue is not flashing or turn on at all then i have a flashing red light please help

Programming doesn't complete, new EVO-ALL on F150/2012, firmware flashed

Sat, 19 Jul 2025 03:52:12 +0000

Can't find anything in the questions/answers that is exactly like this issue but I can't seem to complete the programming on my truck.. I've double and tripple checked the wiring, can-high/low, key sense A1,A10,A20 were connected as well.
First time it seemed to sense the keys, waited the 3 seconds each and returned to the 1st factory key.. waited for 3 or 4 minutes and no status change so I tried it again. Seemed to go a little further and the system locked/unlocked the doors and the stopped again.. no 10x flash of the indicator either. reflashed the unit and tried again, this time nothing seems to progress. I can put the unit into programming mode (blue/red solid) When I touch a key to the ignition I see a quick flash of the yellow, turn to run and wait 3, 2nd key doesn't show anything.. return to the first key and nothing happens. lights won't change at all and just stuck at solid blue/red. I've tried tapping the button when the key is inserted, but that does nothing either. One really strange issue is I started the truck after (unit was still connected) and it would not shut off until I pulled the connectors off the controller.. brake pedal didn't do anything, opening the door didn't light the interior or turn on the parking lights.

Any ideas? THAR-FORD1 with EVO-ALL

New EVO-ALL won't pass step one for programming

Sun, 13 Jul 2025 19:43:20 +0000

Brand new unit EVO-ALL won't pass step 1 for programming. All three lights flash in sync (not alternating) Do these units ship without any firmware?

20 conductor harness wires too short??

Thu, 10 Jul 2025 03:22:35 +0000

I don't understand how people are installing these units, I can't find any way for the wiring to reach the passenger side kick panel. The wires are at least 1 foot too short on the 20 pin connector so is there a trick to the install or do I need to buy an extension? I was hoping to not splice in sections of wire but I will if I have too.
purchased the EVO-FORT1 standalone with THAR-FOR1

Wires that are too short are A17-19 on the 20 pin connector "A"

thanks

Locked evo one

Wed, 25 Jun 2025 13:14:42 +0000

How would I find out if an Evo one is locked. It was manufactured in dec 2018. Sn 002b07 324778. Thank you

How to program after getting new keys made

Wed, 25 Jun 2025 02:10:37 +0000

I broke my original key remote start was working with that key. Locks smith came out and made me two new keys and now remote start doesn’t work. 2008 Ford F-150 with the “Key Override All” and “FirstTech CM900” how to reprogram what’s in trouble shooter page 16 doesn’t work.

2015 Ford F150 won’t go into step #4

Sat, 14 Jun 2025 14:43:26 +0000

2015 Ford 150 with keyless entry and factory hood pin.

During the programming steps, it will not flash after ignition is in RUN position. Blue light remains Solid.

I’ve verified all my connections and are good.

EvoAll s/n: 001A07649192

Firmware: 4.01

Vehicle is shutting off when I open the door

Mon, 19 May 2025 03:46:57 +0000

I have a 2021 Ford escape I used the Evo with the Ford t harness I don't know if I set it up the right way but when I open the door the vehicle shuts off trying to get help with this I use the recommended setting don't know why it's cutting off when I open the door

2016 Mustang MT NCNS

Mon, 12 May 2025 17:46:45 +0000

Good afternoon,

I am having an issue with my 2016 Mustang MT not cranking or starting with the remote start feature. Vehicle goes into ready mode after the correct sequence, the module clicks and a solid red LED appears on the back of the module itself. After setting ready mode, I hop out and press lock twice to kill the vehicle. Lastly, I use the 3x lock sequence to remote start the vehicle, it primes, and I just hear the relay that I installed clicking over and over and the accessory mode turning on and off repeatedly until I manually start the vehicle to break the sequence. I thought it was an issue with the sacrificed key, but I held my regular-use key fob in the vehicle to confirm that it wasn't the issue, still the same condition as before. All connections look to be good, only soldered connections were used.

SN: 002B04 710520

Thank you for your help.

EVO-FORT4 MANUAL TRANSMISSION INSTALLATION GUIDE

Sat, 10 May 2025 07:00:08 +0000

2018 Ford Fiesta with Manual Transmission EVO-FORT4 Installation Guide?

Evo-all with a DSM-550

Sun, 04 May 2025 11:54:52 +0000

All the documentation I can find are from 5 to 6 years ago. Is there any change in status for the Evo-all working with the DSM 550?

Installing EVO-START-LTE on EVO One with exsiting RF Kit

Sat, 12 Apr 2025 17:18:52 +0000

Hi there,

I currently have the EVO One installed on my 2018 Ford Focus Standard Key using a T-Harness kit. Would it be possible to have the RF-912 and the EVO-START-LTE installed at the same time? According to older threads in this community I'm assuming the answer would be no, I just wanted to check to see if things may have changed in the last few years. If I'm able to use both at the same time where would I be able to purchase a subscription (US Based) for the EVO-START-LTE

Thank you

2018 ford edge evo all with radiostar generation

Fri, 04 Apr 2025 07:07:03 +0000

Hello everyone,

Looking to install this evo all with this radiostar generation remote starter (https://policeauctionscanada.com/Listing/Details/49897032/Radiostar-2-Way-LCD-Vehicle-Security-System-Remote-Start-240093B) As my buddy is insisting to use it. It wouldve been a lot easier if i do it with fortin RF kits. Anyway. My question is according to the this diagram on the fortin website (https://cdn02.fortin.ca/download/66011/EVO-ALL_IG_SAL_BI_FOR-EDGE_2015-2017_C_66011.pdf)

Where should i connect all those dotted lines going to the remote starter? There is no datalink on this remote starter. Unlock and lock to the remote starter side? Specifically the “start/stop external” and the “convenient ignition out” from evo all going to the remote starter side? Im confused. Please help. I appreciate it. Thanks in advance

Is there a pause or shut off to relearn tpms sensors

Wed, 26 Mar 2025 12:16:30 +0000

I have 2013 f150. Just changed out tpms sensors. 315mhz. They won't relearn. It may be my remote start blocking it. Is there a quick shut off? Or pause? I have an evo- all

I have a flasklink 4 updater that worked twice and now gives me the usb device not recognized/descriptor failed.

Mon, 24 Mar 2025 15:36:16 +0000

my flashlink 4 worked twice and now is inoperable usb device not recognized/ descriptor failed. I see its been a problem with others as well I hope is a resolution before I have to return it. thanks for the help

Reset flash limit on EVO-ALL S/N 001A07 632473

Thu, 13 Mar 2025 11:10:08 +0000

Please reset the flash limit on my EVO-ALL S/N 001A07 632473. Thank you

2016 F-150 evo all can not program new key

Wed, 26 Feb 2025 13:04:00 +0000

I have 2016 F-150 my remote starter is Evo-all programed with Autostar fob. I got new Auto star fob or remote and I tried many ways to program it but it did not work at all. When I connect to Flashlink to my computer it does mention there is 1 key only. Please I need help ?

Ford f150 2011 Evo all standalone that-for4

Fri, 21 Feb 2025 12:07:57 +0000

Evo all 06/2023

Sn 001A07511495

Ford f150 2011 Evo all standalone that-for4 Doesn’t no program, I have been trying different times and ways and I don’t get it.

Only get that the red and blue lights flashing 10 times but the blue light never come back, waiting long time and it doesn’t flash back. Of course using 2 working keys. I tried using a video that says, press the programming button after uses the second key but it didn’t work either. I tried without connect the red connector but it didn’t. Then I don’t know what more to do. Could you help me please. Thanks.

My 2017 Ford explorer (interceptor) has no PATS can I skip this programming

Tue, 04 Feb 2025 15:16:33 +0000

Since the police interceptor version of Ford Explorer has no anti-theft PATS can I just skip the first part of programming? It seems to just hang there without going any further.

Blue plug on For4 T-harness

Thu, 30 Jan 2025 23:49:35 +0000

I would like to add an rf kit to my installation and wanted to confirm if i can plug and go or need an adapter.

I have an Evo-all installed with a for4 t-harness. is the blue female plug on the t-harness for the rf kits such as rfk442 or is the RFA2A adapter required?

Decryptor Limit Has Been Reached For This Car.

Mon, 27 Jan 2025 09:08:02 +0000

Hi guys. Hi Derek, this box it's locked, I can't flash it and Decrypt. Could you please reset it? Thanks you so much!

S/N: 002B04 689843

Need 2 keys for programming the remote start?

Fri, 24 Jan 2025 18:08:28 +0000

Are 2 original keys really needed for production work on the 2015 ford transit

eve one 912 sur mustang 2006

Fri, 17 Jan 2025 02:31:55 +0000

Bonjour je suis en train d'installer un module Evo one 912 sur une mustang GT 2006.

Le véhicule c'est une boite manuelle , et sur le produit, c'est indiqué compatible avec les boites manuelles.

J'aimerais obtenir une réponse car j'ai commandé le produit, je suis un garage et j'ai donc proposer le montage de ce produit à un de mes clients .

En l'attente

sebastien

Ford Mustang GT 2006 EVO ONE RM912 Pas de démarrage a distance

Thu, 16 Jan 2025 05:03:10 +0000

Bonjour,

Suite à la pose d'un module RM912 sur une Ford Mustang de 2006, Transmission manuelle avec clé standard, impossible de programmer la fonction à distance pour le démarrage

Etant un garage j'ai suivi le schéma de cablage fourni sur le site pour mon modéle, Guide 85601, les télècommandes repondent bien, le boitier clignote en permanence en alternance de 3 couleurs.

Sur cette mustang, faut il passer par Flash Link pour programmer les fonctions ou un branchement supplémentaire est il nécessaire ?

Cordialement.