Questions & Answers - Questions récentes dans la catégorie: Hyundai

More of a Suggestion for an Ammendment

Fri, 17 Jul 2026 23:53:50 +0000

I was having trouble getting an EVO-ONE to program properly in a 2010 Santa Fe. I realize it's an older vehicle so maybe this is a moot point. It would process the CAN just fine, but when it came to the PATS programming I followed the instructions to the letter. I noted that the instructions state that the 3 LEDs should flash in sequence, which led me to believe that they would come on one at a time. They were sequencing, but always in pairs. This was the first misunderstanding. The second one was that the instructions state that the PATS programming may take up to 5min. I even used a stopwatch to time it and gave it a bit longer. Nothing. Finally after spending several hours confirming that EVERYTHING was done correctly, I reset the module (probably for the 5th time) and started again. CAN went in good, started the PATS sequence and walked away for a good 20-30 minutes. When I came back the yellow light was flashing quickly as it was supposed to. So I'd like to suggest that the wording be changed to reflect the fact that the LEDs do not flash in sequence, but in pairs, with a specific pattern, and that the procedure can take longer than 5 minutes. This would have saved me a LOT of time on this install.

2024 Hyundai Elantra N Fortin Evo One LTE Flashes red light 4 times after failed remote start.

Mon, 19 Jan 2026 00:16:32 +0000

All wires seems to be correct from the install manual. Can is reading correct. The car will crank when remote started but nothing. I don't see any security lights on the dash when I attempt to remote start. the red light will flash about 4 times on a failed start. from my understanding its possbily not reading the tach? is theres a recommended setting im missing in pro/wizard? theres no decryption required for the Hyundai correct? and i just program the key on "red" press button 6 times press ignition 2x wait for flashing blue and turn ignition off. I have a 6MT I have updated everything to the most recent firmware. i just cannot seem to figure out the last part. I also have the car under Tech Data-Link. do i have to learn the idle of the car at all for it to stay running? my blue light on the evo one lte dosn't light up when holding brake and holding button to learn tach. Any advice would be great! Thank you!

2007 Santa Fe refuses to learn immoblizer EVO ONE

Tue, 30 Dec 2025 19:10:03 +0000

Trying to Pair immobilizer to evo one on last step and refuses to learn and flash yellow light, TImes out after about 15 minutes and flashes red.

It did learn before when temporarily hooked up, Checked wiring and all is correct. Reflashed firmware and reset module with alternating lights.

Getting proper can Voltage on both wires at Evo connector and all other pats wires

Take Over

Tue, 09 Dec 2025 20:00:17 +0000

Hello. When I install a remote start with Fortin on new Prado, pressing the start-stop button helps prevent the engine from stalling when I press the brake. However, on Kia and Hyundai, pressing the start-stop button doesn't help. The engine still stalls when I press the drake. What's the cause?

Is it possible to pair a remote to evo-start 2?

Tue, 18 Nov 2025 15:21:08 +0000

Good Morning,

I moved to Alberta from Ontario. I had an evos-tart 2 smart phone remote starter installed on my car when i bought it at the dealership in 2019. Ever since moving to Alberta, i was never able to start my car with my phone. I than noticed that there was no coverage for evo-start 2 in Alberta. Would it be possible to pair a remote/fob key to my evo-start 2?

Thank you for your time.

Alex Belanger

2018 Sonata Push Start T-Harness?

Thu, 28 Aug 2025 04:16:42 +0000

Is there a T-Harness available for a 2018 Sonata with Push-to-Start? THAR‑ONE‑KHY8 implies so, but only one Hyundai model is listed.

service interruption with upgraded service plan?

Fri, 02 May 2025 19:04:38 +0000

Evo Start to expire in 15 days. 3 year was purchased to extend service on 05/02/25. App on I-phone states "service will be interrupted in 14 days." When will my service plan update in my account and not delay/interrupt my service for my Evo Start

Device flash limit reset request

Mon, 24 Feb 2025 21:17:14 +0000

Hello,

Evo-All on a 2014 Hyundai Elantra standard key, Service Number: 001A06 357048
I need a flash limit reset please. Thank you!

Hyundai Tucson horn wire

Fri, 21 Feb 2025 01:58:12 +0000

Can you please help me on 2015 Hyundai Tucson horn wire location I would like add Evo-one alarm.

Thank you very much.

antenne evo start

Tue, 04 Feb 2025 12:41:10 +0000

Bonjour jaimerais savoir si il a une facon de faire un reset de code si on vient d'acheter un vehicule et sa dit le code sur l'antenne est deja utiliser mais que nous avon pas les information de lancien proprietaire

Flash limit reached

Mon, 03 Feb 2025 08:06:12 +0000

Hi guys here again with this box. Hi Derek, this box it's locked, I can't flash it and Decrypt. By the way, please this box was locked trying to use on 2013 Hyundai Elantra. I tried with each firmware and doesn't work with any of them. Could you please check all these firmwares? When I try programming it, the red led remain on red. Pressing the program button or not once you plug the 12v harness. Thanks you so much!

S/N: 002B04 689843

Démarreur a distance Iphone

Mon, 27 Jan 2025 01:01:00 +0000

Salut,

J’ai acheter une voiture d'occasion à un concessionnaire (Hyundai Seray à Chambly) un hyundai tucson 2014

1 ans plus tard, je me suis pencher à savoir quel est la marque de mon démarreur à distance que j’ai sur ma voiture et je remarque que c’est un Evo Start.

Ma manette (démarreur) c’est inscrit « Duo » donc j’ai surement un Evo Start 2 dans ma voiture. J’ai donc fait des recherche sur celui ci, et j’ai remarquer qui a une application mais sur celui ci, sa me demande un Code. Où trouver ce code?

2017 Tuscon push start issues

Mon, 06 Jan 2025 09:33:12 +0000

Installed evo one with t-harness, tried to program and unit doesn't seem to work. No to start or stop the engine,

I need to press start/stop two times? Any suggestions or help would be appreciated. without hood pin, A11 should be on or off? Only wire that i had to splice was the lift gate wire...

2022 Hyundai Accent - Std-Key-without-Keyless

Sun, 05 Jan 2025 20:27:35 +0000

I have a 2022 Hyundai Accent and two options appear. I don't know what they mean.

Std-Key-without-Keyless
Std-Key-with-Keyless

Hyundai Elantra 2016 Evo-One with Standard Key PATS

Sat, 28 Dec 2024 22:40:04 +0000

Canadian version with the immobilizer and harness THAR-ONE-KHY2

Firmware updated to latest.

Programing process completes. Yellow LED method

Question I have is....

I'm not clear with what the manual means by cutting.

A20/D4 and A10/D6 from the blue PATS ~ wire....

A10, D6 and the blue PATS ~ is tapped into the blue PATS ~

A20 to D4 is connected together...

Did the manual mean I have to use A10/D6 from the blue PATS ~ wire by breaking the connection of the blue wire from the connector

side then connecting it back to the blue PATS ~ using A20/D4 back to the blue PATS~ ?

Is this what I am supposed to do?

2022 Elantra N Manual. When in ready mode, press ignition once, then brake and car will lock after closing door.

Thu, 12 Dec 2024 22:02:07 +0000

Accidentally locked self out of car once. What setting is causing this? Go to neutral, and pull ebrake. Press ingition once, then brake, car turns off. When the door is opened and then closed it locks even if key is inside.

Is 2017 Tuscon push start with Eco-One and THAR-KHY7 truly plug n play....NO cutting or splicing needed?

Tue, 19 Nov 2024 08:02:12 +0000

Is this truly just a plug and play or do I need to search and splice wires?

2013 Hyundai Genesis Coupe auto- Alarm going off after remote starting

Tue, 12 Nov 2024 18:45:28 +0000

Had the EVO ONE installed for about a year with all the functions working. The engine locked up and after the dealer replaced it everything still works except when you remote start about 20ish seconds past and the car alarm will go off. I've tried changing some settings, the master reset ( plug in the big connector and let the button go when its red then hold again until it cycles) then flashing it again still no change. I checked the wiring and found no breakage or cuts.

2 things I've noticed is that if I'm trying to do the KEY BYPASS PROGRAMMING PROCEDURE after I get solid yellow and I plug in the rest of the connectors and turn the car on the light does not change, tried about 4 times, but when I do the PROGRAMMING VEHICLE WITHOUT PATS DATA WIRE (even thought I did the PATS wiring like the diagram said) I get through all the steps no problem and end up with the original issue.

2nd thing is when I remote start it unlocks then locks and starts (like it should) then after a couple of seconds it locks again which I feel like its arming the alarm because I tested unlocking the car after that second lock and around the time the alarm would normally go off it doesn't but what happens is the car relocks its self then after some seconds the alarm goes off again.

Also note if I turn the alarm off the cycle of the car locking itself again then the alarm going off will continue forever until I either disable the remote start or put my key and turn it to the on position

To me its sounding like the EVO one isn't acting like the "key" which points to the key bypass Issue and I cannot seem to find a forum about the problem I am having

EVO One RFK441 2010 Hyundai Tuscon, regular key. Remotes only work every so often.

Fri, 08 Nov 2024 23:28:46 +0000

Everything programmed correctly as per the guide, no issues there. The remotes, even though they are one way, seem like they are acting as a 2 way remote. Both remotes programmed correctly on initial setup. Sometimes one of the remotes will work correctly to lock and unlock the doors, the LED on the remote giving one initial flash, then 5 quick flashes and the function works on the car. Other times, you push the lock or unlock, and all you get is a single flash, and no response from the car. It is very random, sometimes it's one remote, sometimes it's the other. Sometimes when I pick up one of the remotes, I see the LED give a single flash, but I haven't pushed a button.

After a period of time, they both seem to start working properly to lock and unlock the car. Once that happens, you can remote start it once. Sometimes you can shut it down with the remote, sometimes you cannot. After that, neither one of the remotes will work at all. They go back to a single LED flash when the lock or unlock is pressed. Eventually one of them will start to work, then the other.........This has to be the strangest behavior I've seen from an RF remote.

Hyundai Elantra GT 2017 - MS3G app not working properly.

Mon, 21 Oct 2024 23:40:16 +0000

Hello, I have the MS3G app on my Samsung. My car starts perfectly, but the 15 minutes timer no longer appears, I no longer have notifications and the 3 circles beside the car image no longer have anything showing one the car starts. Shows in the left upper corner as "layout empty". Background app refresh is on, and notifications are on as well. I have tried de-installing, clear data, clear cache and rebooting my phone. Thank you!!

Is the Evo One compatible with Hyundai Sonata 2007?

Wed, 16 Oct 2024 01:46:35 +0000

Hello, I would like to know if the "EVO-ALL Universal all-in-one data bypass and interface module" is compatible with Hyundai Sonata 2007 please?

Thanks and regards,

Deeshan

Hyundai Accent 2022. ‏ Push to start

Sun, 15 Sep 2024 06:20:45 +0000

Hello support team,

I have Hyundai Accent 2022. ‏ Push to start but it is not included in the VEHICLE FINDER only the key

I searched for 2021, what is the solution?

This device has no network temporarily...

Thu, 08 Aug 2024 18:43:59 +0000

Daughter went to remote start with Evo Start and Evo One via iPhone app and the app says "This device has no network temporarily, and the remote start is invalid!"

I am assuming a signal issue but any info would be appreciated for troubleshooting.... Hyundai Santa Fe pts, factory 3 Lock start with iPhone app Evo Start LTE and Evo One installed. I am awaiting her arrival to check led status on both units. 3 lock start worked fine.

Thank you!

Fortin Evo Start - No fuel reading - 2012 Sonata

Fri, 24 May 2024 19:42:14 +0000

Installed Fortin EVO ALL + Fortin EVO Start. Everything works except for fuel gauge reading on app.

I am able use all available app functions for remote start, door close, lock/unlock, GPS, internal temperature. On the App I am unable to get fuel level to be displayed. (see attached screenshot)

https://photos.app.goo.gl/pi3MAUQ8rGQbjYpM6

2012 Hyundai Sonata PTS - No ignition control - EVO All

Mon, 20 May 2024 01:20:25 +0000

2012 Hyundai PTS

Fortin EVO All with Fortin LTE

Connected all wires as per installation instructions. Bought Flash link and flashed to 17.31 following the wizard. Programmed Frotin Evo module to vehicle(blue LED blinks rapidly). When pressing starting lock 3x - module sounds internal relay is clicking and parking light flash however dash ignition does not come on. Checking EVO all diagram - RED Connected D2 yellow/blue start+ wires goes into 1n4004 diodes - strip facing towards PTS button - then to yellow/black and yellow/orange. ignition does not turn on.

Disconnected the diodes to measure direct and yellow/blue wire for voltage output...getting zero volts when remote start is requested. Tried to reflash Fortin 4 times and still have not been able to get voltage output from d2 yellow/blue.

I am missing something or is there internal module fault?

Remote not working

Thu, 09 May 2024 10:28:41 +0000

I purchased 2017 hyundai elantra that has a Fortin remote starter installed, but the remote is dead.

Remote model

Model FTX64

FCC ID 2ACKU-R2W01FM
IC: 12084A-R2W01FM

Fortin 04G

How do I purchase a new replacement remote and get it programmed?

Thanks

hyundai door lock

Tue, 20 Feb 2024 09:22:42 +0000

Good afternoon. On Hyundai cars, after turning off the engine, the doors will unlock after a couple of seconds... What can be done to ensure that they remain closed at the end?

What do the colored numbers mean on the instructions. No explanation on how Wirecolor guides work. Please explain.

Wed, 07 Feb 2024 22:02:00 +0000

Can I please get an explanation of the Wirecolor instructions?

Why don’t I get any LED lights on the evo-all during programming?

Sat, 13 Jan 2024 10:27:37 +0000

I have checked all wiring and have a good ground. There is power to the evo-all but no lights.

Washed my remote ,no start Evo e400

Fri, 12 Jan 2024 23:44:23 +0000

I programmed the module. But remote is not programming.

Disable the horn when I unlock the car in the morning after remote starting it?

Mon, 08 Jan 2024 15:01:48 +0000

Every morning when I click unlock after remote starting (I guess anytime unlocking for that matter) the horn honks, and it's driving both myself and my neighbors crazy. Is there a way to disable this on unlock? 2020 Hyundai Elantra, do I need to reprogram this thing? If so I may just cut the wire, but hoping there may be a quick fix to it.

2014 Hyundai Sante Fe Evo One Lte. factory remote

Fri, 29 Dec 2023 17:10:48 +0000

Hello, I installed Evo One Lte in my 2014 Hyundai Santa Fe Sport PTS. The Evo start works great via the Cell app but i cant get the factory remote to start the car. Also, the cell app WILL NOT operate the door lock/ unlock. The list says 3 locks will start and stop remote start, but i cant get it to work. Not sure if its my fault or If factory fobs will not work on this vehicle

Any help is greatly welcome !!!! THANK YOU ALL VERY VERY MUCH

IS there a T harness for 2014 Hyundai Sante Fe Sport Push To Start?

Thu, 21 Dec 2023 19:59:43 +0000

Hello, is there a T harness for 2014 Hyundai Sante Fe Sport Push To Start?

Did not see one but wanted to double check.

Thank you for your time.

Why does my device show offline

Wed, 06 Dec 2023 21:50:34 +0000

My evo start was running fine for the first year, yesterday at 10am it stopped working and anytime I try to send a request it says device is offline. How to I fix this? I was in the middle of driving to work when it went offline, according to the history.

Question about diagram in 73971

Tue, 05 Dec 2023 20:45:26 +0000

Hi all,

Looking at the install for a 2020 Kona, diagram 73971. On page 6, lower left corner on the steering wheel, there are a couple of "7" dots. Based on what I'm reading, the top 7 should be removed and the bottom one should be changed to 8 because it refers to the location of the horn. If not, can you clarify?

Thanks,
Josh

Mycar2 with rfkit 411

Fri, 24 Nov 2023 18:33:10 +0000

I recently installed mycar2 app with Fortin e400 module. The app is working fine along with the module. However is it possible to install RFkit 411 or 441 to the same system. Is it either my car2 or rf kit?

Fortin E400 compatiblilty

Wed, 08 Nov 2023 19:00:01 +0000

Looking for compatible replacement remote for fortin e400 module that initially came with Antenna Fortin "AM"

Looking to replace just the antenna if need be that can work with my originally installed E400

2019 Veloster PTS Manual, Bypass wont program

Mon, 30 Oct 2023 21:38:14 +0000

2019 Veloster PTS Manual. Wire to wire according to https://fortin.ca/download/98741/EVO-ONE_IG_RTO_BI_KHY8-VELOSTER_2019_PTS_B_98741.pdf

Bypass wont program when ignition is pressed twice.

Any advice on troubleshooting would be greatly appreciated.

2019 Elantra PTS, unable to program CanBus to Evo-One

Mon, 30 Oct 2023 14:14:23 +0000

Installed Evo-One on a 2019 Hyundai Elantra PTS. Verified wiring many times. When it comes to programming the module, all goes well till it’s time to program canbus section. I get it to the point the red led is flashing 5X then pauses. Push the PTS button twice to turn on ignition for canbus programming and nothing. No red led 10x then turning to blue. Any ideas into why this is happening would be great. Can usually get these figured out, but no luck here. Car has 2 different canbus hook ups, one at the obd connector and one behind the fuse panel.

2019 Sonata plug-in

Mon, 30 Oct 2023 09:06:58 +0000

Hello. I want to install evo-one on the Sonata (plug-in hybrid). Will the car start or not remotely if the charger is connected?...

EVO-ONE-3641 1-Way Remote Starter Will get my locks crazy! I press once and it makes the commands twice.

Mon, 09 Oct 2023 22:11:37 +0000

When pressing the unlock button it will do the command twice same when pressing the lock button

EVO-ONE-3641 1-Way Remote Starter

I purchased a single use token. It was never emailed to me,

Wed, 27 Sep 2023 23:30:10 +0000

I am logged in, but when i pick a vehicle from the drop down box at the top of the page, it doesn't ask if i want to use a token. I bought this token on 9/5 and still haven't been able to use it, please help

how to you replace the battery for ftx64-2w, it seems to be sealed for some reason ...?

Wed, 21 Jun 2023 20:03:29 +0000

how to you replace the battery for ftx64-2w, it seems to be sealed for some reason ...?

NT900 antenna not defected.By flash link updater 4

Sat, 22 Apr 2023 12:38:27 +0000

i pluged the flash link updateter to the computer . i slelect special unit then i pluged the NT 900 to the flash link cable but nothing happens just i hear click from the flash link and blue light blink ones in The antenna.any help ?

evo one with FORTIN EVO-ONE-912

Wed, 19 Apr 2023 06:27:06 +0000

FORTIN EVO-ONE-912 with no blinking LED after follwing all inestruction igntion on off on 4x brake padel the blue led wont come on or flash.the red led under the loop in the evo one flashes but the ANT900 not responding at all.

- when i plug the wire in the ant 900 led will blink ones and thats it and when i try to update the RFkit by flash link updater it wont dedect it . i am suspecting ANT900 anttina defected.Any help ? thanks

Postion sur carte (Set location)

Mon, 06 Mar 2023 09:23:27 +0000

Bonjour,

EvoStart 2 quand je lcique sur la position qui devrait me donner soit la position de l'auto ou autre...ca me donne toujours la meme position meme si je me deplace......??? comment resoudre ce trouble!!

Merci

M.Pelletier

2018 Tucson

Thu, 02 Mar 2023 12:26:34 +0000

Hello. I'm currently installing an evo-one on a 2018 Tucson. The blue connector in the kick panel is different from the one shown in the diagram (97941). EMC com is not located there. There is a white wire in another place and it says LIN...Use this white wire?

how do i wire up the door unlock so i can gain access to the car after remote started

Wed, 01 Mar 2023 13:44:31 +0000

I see that in the evo model their are wires to lock and unlock the doors for a 2014 Hyundai Santa Fe with Key start, however i cannot find any info on where to connect the unlock wire from the evo starter to the car so that i can unlock the doors after remote starting it.

2015 Santa Fe no response with 3x lock

Mon, 06 Feb 2023 14:37:36 +0000

Installed Evo One in 2015 Hyundai Santa Fe PTS. All connections have been checked. Module seems to program fine according to LEDs. Yellow LED lights with vehicle in run position. No LEDs illuminate when pressing the remote buttons, and the car does not respond in any way. Tried a second unit and same symptoms.

Elantra 2009 Ready mode not engaging

Sat, 21 Jan 2023 16:04:29 +0000

Hi,

2009 elantra manual model with clutch switch bypassed.

When trying to activate ready mode, the ligths flashes 3 times but upon turning the ignition off, the engine stops and when attempting to remote start it flashes 3 times indicating ready mode not set.

The ignition 1 and ignition 2 wire are connected. Accessory wire is wired to accessory also. Yellow wire from evo one goes to clutch switch.

Key was bypassed and door locks work. I'm thinking it doesn't engage into ready mode as the unit doesn't see engine RPM on the CAN maybe ? Because using the RF as the only setting to engage ready mode still didn't work.

Thank you