Questions & Answers - Questions récentes tagguées -

Need detailed instuctions for fortin evo chrt7 kit for 2023 ram 1500 classic tip key

Sat, 07 Feb 2026 21:08:51 +0000

Purchased fortin kit evo chrt7 for a 2023 ram 1500 classic with tip key start. No instructions came with it in box. There are 2 harnesses a t harness and obd2 harness . looked thru the qustion section on this site but no instructions for a 2023 ram 1500 classic or how to connect the obd2 harness for true plug and play, no having to tap in original wireing like in the kit description. Need updated specific instrutions or installation video.

Sent start request thru App - Said it started, it did not... almost killed battery

Sun, 14 Dec 2025 19:58:50 +0000

The app has worked both hot and cold for the last 6 months no issues.

I replaced my 12v battery as it had been 5 years on Friday. I drove good distances afterwards, and I also remote started more than once since then.

This morning I remote started thru app, it said vehicle started, but it never showed the headlights etc come on. I've been using the app to monitor voltage (because I knew my 12v was weak this winter before I replaced it) - So I noticed I started at 12.6. After issuing remote start I dropped quickly to 12.2, then got the alert in the app of 11.7. By the time I got to the car it was 11.1. The car was NOT running, just ignition was on.

I hit the brake. Then pressed the brake and started manually and everything is working normally now.

Any ideas on what caused this?

In addition - I accidently left my trunk open last week - the car app never alerted me (though I just found and saw that there is a setting for that).

2021 Toyota Rav4 PRIME w/T-Harness install LTE-ONE.

Thanks

service interruption with upgraded service plan?

Fri, 02 May 2025 19:04:38 +0000

Evo Start to expire in 15 days. 3 year was purchased to extend service on 05/02/25. App on I-phone states "service will be interrupted in 14 days." When will my service plan update in my account and not delay/interrupt my service for my Evo Start

2009 Suzuki Grand Vitara By Pass Programing

Wed, 25 Sep 2024 21:45:30 +0000

2009 Suzuki Grand Vitara Installed EVO ONE. Updated and set up using the flash link updater 4. Step 4 procedure after the yellow LED flashes twice the the blue, yellow and red lights flash together - 2 times then goes out. Tried a few times on re-flash and decode update. What do you think is the issue?

The current device cannot be flashed anymore

Mon, 10 Jul 2023 19:07:39 +0000

أحاول معرفة سبب عدم بدء التشغيل عن بُعد في تويوتا كامري 2023 بعد الآن.

عندما حاولت إعادة برمجة السيارة ، كانت الرسالة هي أن Dcryptor قد وصل إلى الحد الأقصى.

SN : 001A07469244

كان عليك الضغط على زر إلغاء القفل لإعادة البرمجة. شكرًا لك.

Could you please reset this limit

Hello! Which EVO kit and T-HARNESS will fit my car? Nissan Teana L33 2014 Europe.

Sun, 25 Sep 2022 08:10:49 +0000

Эта машина на платформе Altima! Но только европейской сборки. Мне интересно, куплю ли я комплект EVO All NIST4. Подойдет ли распиновка проводки и жгута для моего автомобиля?

module not blinking rapidly at step 5

Sat, 03 Sep 2022 13:48:10 +0000

Hello Team, I have gotten the RF Kit (RFK411) as advised but while trying to start the programming all over, I observed that the red light on the device remained solid as it was supposed to flash rapidly about 10 times as stated in step 5. I have tried reprogramming all over again several times but the red light still remains solid on step 5 and this has prevented me from going to the next step. Will the check for the Rx and Tx connections be via a remote connection to the module? Although I saw clearly that the red light blinked rapidly during the initial programming and several other times as attempt was being made to get the vehicle to start via the OEM remote without the RF Kit. It was after I made an inquiry and tried reprogramming all over again that I observed it was not blinking rapidly and still stayed solid when the vehicle was turned on with the press and release of the programming button. EVO-ONE S/N: 002B04 171979

Under what conditions are the (+)IGNITION2 contacts supposed to open on Mazda CX5?

Wed, 22 Jun 2022 10:55:03 +0000

Should the contacts for the (+)IGNITION@ relay ever open? They always seem to be closed

why does decryptor programming fail at step 4

Sat, 12 Feb 2022 12:07:25 +0000

sent evo all out and was flashed. I know nothing about what he did. Keys program ok. Decryptor program fails at steps 3-4 . I have it with t-harness thor 1

2013 FORD FIESTA EVO-ALL- starts on its own After driving vehicle and 1xlock is used to lock doors after

Wed, 12 Jan 2022 23:00:06 +0000

2013 FORD FIESTA

EVO-ALL WITH THOR-FOR1 T-HARNESS

S/N 001A07321575

1 OEM Key programed

lock / unlock/ lock for start sequence

Yellow/black wire on 20 pin connector is NOT grounded

EVO-ALL performs as expected until you exit the vehicle after driving and you lock the doors using the 1x lock on the OEM Key. As you walk away from the vehicle the Evo-All starts the vehicle on its own. Once this occurs the vehicle can be shut down using the lock/unlock/lock

Have tried exiting vehicle with brake depressed while using door handle to unlock the vehicle on exit. which should disengage the Evo-All. However, the vehicle still starts once lock the doors using 1xlock with the OEM key

2013 Ford Fiesta Evo All with THOR-For1 T-harness will not Activate/Respond when remote start attempted using OEM 3Xlock

Wed, 05 Jan 2022 00:36:28 +0000

2013 Ford Fiesta Evo-All with THOR-For1 T-harness will not Activate/Respond when remote start attempted using OEM 3X lock

One OEM key

Wiring completed per Instalation Guide #58161

Decryptor programed per process outlined starting Page 8 of Guide #58161 for one OEM key

When completing steps 1 to 9 all lights correctly match the Guide #58161 with step 9 flashing blue and then to Step 10 alternating Flashing Red to Yellow when key turned off

Completed Steps 11 to 13 using Flashlink Dispalys successfully Programed

When reconnected to wiring harnesses and perform 3x lock on OEM Key there is no response of any kind from Remote start..

All wiring have been confirmed to be correct per Guide #58161

With ignion key off and key out there are no lights displayed on the Evo-All

When engine is running with key the Yellow Evo-All light is dispalyed solid

2004 4RUNNER REMOTE STARTS FOR FEW SECONDS THEN DIES

Sun, 12 Dec 2021 18:04:12 +0000

2004 4RUNNER EVO-ONE INSTALL

THE REMOTE STARTS THE VEHICLE BUT DIES AFTER 8SECONDS AND IT DOES THIS FOR 2X.

ALSO THE LOCK FUNCTION DOES NOT WORK; I PROBED THE A2 PURPLE WIRE AND ITS CONSTANTLY GIVING OUT A NEGATIVE SIGNAL. IS THIS NORMAL?

I DID THE RESET AND STILL DID NOT WORK

PLEASE HELP

THANKS

Cx5 key handoff - shuts off on door being opened

Thu, 18 Nov 2021 23:11:57 +0000

Engine shuts off on door being opened. What setting needs to be changed to allow key handoff? 2016 Mazda CX5 I'm using evo-all with maz1 t harness. Thanx

Compatible with EVO RS -ALL IN ONE - FORT 1 on 2013 Mustang manual transmission vehicles?

Tue, 19 Oct 2021 21:55:48 +0000

Compatible with EVO RS -ALL IN ONE - FORT 1 on 2013 Mustang manual transmission vehicles?

I would like to know exactly how to remotely start the s197(13y) Mustang manual transmission.

What setting would be needed to enable using RF 442 kit with Evo all kit and a Fort1 T harness

Fri, 08 Oct 2021 17:52:15 +0000

what setting woule be needed to enable for using RF 442 kit with Evo all

2016 Juke parking light wire resets car features

Sun, 02 May 2021 13:47:32 +0000

I have 2 2016 Nissan Jukes, yes, his and hers. My starter works fine and turns on the parking lights (brown wire to purple wire of green pin1 at BCM connector), when I put the brown to purple in my wifes car, the lights don't turn on and it resets the radio/time to factory, every time. Again, identical 2016 Jukes. I am NOT pulling the starter out of her car as where I have it tucked in takes a long time to get at.

Verified 12v at purple wire with manually turning on the parking lights but when remote started the Fortin brown wire has nothing. Ideas?

oem fob wont unlock doors and obdii powers my HUD when tundra not running

Thu, 24 Dec 2020 19:00:01 +0000

2017 tundra. so, i installed the evo one using the thar toy7. i also added the evo start 2. install and programing seemed to go well. But now my oem fob wont let me unlock the doors and when my truck is not runnuin, my aftermarket OBDII powered Head up display turns on and off making a beep sound every 20 seconds or so. I must have made a bad choice in the programing phaze.

Immobilizer wire color and pin location do not match diagram downloaded from fortin website.

Sun, 13 Dec 2020 13:28:37 +0000

SL3 - 2010 Acura TL 3.7 - Standard key

2015 Nissan Altima Ignition Ignition 2 wire

Wed, 02 Dec 2020 10:08:45 +0000

Not a question so much as an update to your notes. On the installation instructions it shows Ignition 2 as Pin 9 Black 24 Pin plug as a Pink wire. Vehicle I had it is not a Pink Wire it is Brown but when tested goes + when PTS is hit for ACC or IGN.

P0513 code 2005 Chrysler 300c Evo All Stand Alone Connection F Everything Working.

Tue, 17 Nov 2020 22:26:03 +0000

It's like a false/positive situation. I had someone overpress my rf remote and oem key was starting car on one lock. blah blah blah

Reprogrammed both sets of keys (2 oem's and 2 RF RM411 long range one way remotes). Everything works fine again, but if I use the one button RF RM411 I get the code thrown and a little red security light stays on for a couple of seconds once my key is in on position in ignition.

Now if I just use the OEM key, I don't get the red light. Also there is no engine light with code. The only reason I know it's there is I had the car seafoamed (should have done through break booster after MAF, used intake manifold. Had engine lights galore and ended up changing all 16 spark plugs myself (the good ones) and clearing misfire and crankshaft sensor codes.

Anyways, all is working great now, except this code I can't seem to clear in any way. Is this an issue with my car or Chrysler products?

Usually when you have this code, the car will start but quit soon after.

Just let me know and I will just leave it alone and not worry about it.

It's perfect except one thing. heated seats. it may be working (hasn't been cold)

Sun, 08 Nov 2020 02:37:12 +0000

2005 chrysler 300c do I have the ability to turn on heated seats without connecting a specific wire? Is this temp driven? I absolutely love using Idle mode/pit stop mode with the RFK411 long range one way remote with my evo all and the adapter. I live in the Pacific Northwest, so not a huge deal.

All in all the device is working great!

How to install the valet switch Evo All Standalone installation.

Mon, 02 Nov 2020 13:42:22 +0000

Please do my a favour. Talk to me like I'm 7 and give me the step by step process of installing the valet switch.

1. connect which side of the wire to A13 (I'm thinking the black wire with grey checks (positive side).

2. find a metal piece and attach wire that is black to a screw and fasten it.

3. Mount switch (where most people mount this).

I'm having some recall work done with the air bag inflators on Nov 12th from the dealer. Also curious how to install this thing properly,

2005 Chrysler 300c Evo All Standalone install Chrt5 T Harness Part 3 (Solved)

Thu, 29 Oct 2020 20:47:49 +0000

I have fully installed wiring using Military Splice method with a stripping tool. Each wire has 3m electrical tape and a small zip tie. So clean the military would be proud lol.

I have triple checked the wiring and everything is right. I think we're at a point that you need to look at my Service Tag # 001A07135564.

This car will not remote start, shouldn't be this difficult. Perhaps a bad T-Harness???

I see you used my ignition harness picture on WireColor.com lmao, maybe you should have waited. Also see you revised the install guide as well using my info. If the car won't start, how is this helping?

I went over the colour of each wire several times to be sure before I made this post. HELP!

Install help. Evo All Stand Alone install with T-Harness CHR5 2005 Chrysler 300c

Mon, 19 Oct 2020 19:13:49 +0000

Stand Alone Evo All with T-Harness CHR5 2005 Chrysler 300c

Have a few questions before install on a 2005 Chrysler 300c using the EVO ALL with T-Harness CHR5. I'll have the unit at the end of the week and just want to go through a quick walkthrough on how I think the install should go.

(No hood pin or saftey valet switch so not talking about those connections).

Will be using Parking Lights.

Unit arrives. Flash the update puck to most recent software and firmware. Then update Evo All to your cars model year trim and set settings, save, exit , unplug

I will do a quick check using Wirecolor website to make sure my wire colors are correct

Wire Harness yellow wire and yellow (A1) on 20 pin connector are connected and isolate Purple wire on harness.

A14 (MUX) Parking Lights wire cute and solder a 2.4k ohm resistor 1/4 watt wrap some electrical tape and connect it with T-Tap on pin wire (from headlight switch) position 1 white/brown wire.

A18 (Mux) from 20 pin goes to position 2 (Purple/Brown) on Ignition Switch with T-Tap

5 Pin white connector just seems to plug in without isolating any wires.

Now the RED connector uses 3 of 6 of it's wires. Also says "IF (+) STARTER WIRE IS PRESENT" for D6. This is my stop gap. Are these D3,D6,D5 T-Tap connections or kept on the harness and wires not used isolated. Also if my starter wire is not present do i isolate D6 as well?

If I get past this I see the programming side is straight forward. Once done and keys are programed unplug unit and use the update puck and run Dcryptor , check settings again, save and exit. Put it back in the car , test, button her up.

Blue light never flashes

Wed, 14 Oct 2020 17:30:20 +0000

I have a 2020 ram 1500, tip key , gas model truck. When following the directions I get to step 7 which is where I get the red and blue lights when inserting the key but then my red light goes off where it should stay on and the next step completely fails as the blue light just goes out and does not flash when it should. Anyone have the answer to this issue or is there another wire that needs to be hooked up other than my 2 can high and low and yellow to ign?

how do I program RF642W fobs to work on Evo-one?

Sat, 01 Aug 2020 13:05:25 +0000

i have installed an Evo-one on my 2019 mazda cx5 and the OEM key fob 3x lock start is working fine. I have also included the RF642W when i programmed / flashed the module. I am not sure what to do next to make the rf kit functioning. i am a bit confused with the quick guide. I dont get the same response from the system (as stated on the guide) when trying to do the steps on programming the fobs. not sure what I am missing.

Evo ALL - T-harness modify for RF-KIT

Wed, 15 Apr 2020 10:25:46 +0000

Hello,
I have Jeep JK 2012, with EVO ALL and T-Harness.
I have also Fortin RF KIT (RFK912 2 way).
How to modify the harness without RF-A2A cable to work wit RF KIT?
Thanks

EVOSTART2 thinks 2017 Sierra is unlocked whem oem remote locked it and vise versa for lock

Fri, 17 Jan 2020 23:58:04 +0000

Evostart2 doesn't know if truck is locked or unlocked unless done so by app

2014 Chevrolet tahoe, after remote starting, engine stops running immediately when key inserted or brake pedal presed

Thu, 19 Dec 2019 15:24:23 +0000

Installed evo-all on 2014 Chevrolet Tahoe with t-harness and without data link. Firmware version 70.24. After remote starting vehicle then unlocking doors, entering the vehicle and closing doors the engine immediately stops running after brake pedal is pressed or key is inserted into ignition.

2019 HR-V remote starts, but OEM remote won't unlock evo-one

Thu, 07 Nov 2019 11:54:26 +0000

Okay, after reprogramming the unit a third time, remote start works properly, but the oem remote will not unlock the vehicle. When I use the key to unlock the door, the car shuts down, is this because I am using the kley to open the door? Setting is on disable for kill engine when door opens. Any help? Evo-one with Honda T harness

Red and white wire came out of harness where does it go

Fri, 15 Mar 2019 01:04:45 +0000

I have a red and white wire with the connector pin on the end and it is not in a connector. One end of that wire goes to my smaller ignition t wire harness so I know it goes somewhere just dont know where.

2014 rav4 hkey with toy-3 harness, programming seems to have worked but does not remote start

Fri, 18 Jan 2019 03:40:33 +0000

I've connected all the required wires using the toy-3 harness (I don't have TPMS so did not connect those two and I didn't connect the hood pin contact). I updated the unit using the flash link updater to the settings in the guide. I programmed the evo-one and got all the lights as per the guide, after the blue led was flashing rapidly i turned off the ignition and the evo-all stopped flashing. When i press the lock button the blue light flashes each time but the rav4 does not remote start.

Unable to get the second programming step to work on my 2009 Mustang

Sat, 22 Dec 2018 19:27:02 +0000

The blue programming step completes successfully and I can star the car with the fob near the ignition. I set the evo-all with the steady red light, but after cycling both keys and holding the programming button, nothing happens and eventually it cycles through all colors. Running firmware 71.47 on hardware version 6

Golf R 2017 activation via handbrake

Sat, 10 Nov 2018 09:02:27 +0000

VW Golf R 2017 Manual transmission with evo-one 78.35/1.24.

is it possible to do option 33.2 (activation via brake/handbrake) when 20.6 (tach data-link only) or do I have to wire the tach?

Sl3 only works when warm weather

Sun, 28 Oct 2018 15:06:54 +0000

I have a compustart remote starter alarm with a Honda Accord Honda SL-3 module bypass but it only works In warmer weather. Starts up with no problem all summer but in cooler weather it doesn’t want to work. Anyone can help will be greatly appreciated. All wiring is hooked up right. I assume wiring is right or it wouldn’t work at all in warm weather.

MyCar app not showing runtime and only starts less than half time.

Wed, 17 Oct 2018 22:06:21 +0000

2014 RAV4. EVO All. Crimestopper Cool Start RS00-G5. T-harness. I finally got this setup to work with the OEM black H-key remote with 3X Lock press. I still don’t get a parking light conformation, and the doors won’t unlock, via automatically or with the fob. The MyCar app shows battery and signal levels, and GPS location. No runtime, or remote start conformation. It only seems to start after I open the map and it is located. Then it will start, shutdown and locks require the same. I do have a Fortin flashing tool, and don’t know what else to do.

Please help?!?!

Thank you!

Evostart 2

Mon, 15 Oct 2018 13:17:02 +0000

I just had the EvoStart 2 Module installed on my 2015 Hyundai Elantra GT and the App installed on my Iphone 7... 3 weeks ago.

Sometimes it starts and sometimes it doesn't. When it does start, I don't get any notification that the car has started with the RPM symbol. Anyone know why?

17 JKU Base Model

Sat, 16 Jun 2018 12:16:07 +0000

Installing Evo-All with an Avital 4105L All connections are made from the evo to the 4105, when I press remote start the ignition comes on, evo lights yellow. But it does not crank. Tries 3 times then shuts off. I read about the green/red wire to the purple wire, but also have read not to do it on a wrangler.

Been using this system for a while but it doenst work the way it should. Need more install solutions.

Tue, 29 May 2018 15:59:49 +0000

Bought this in 2013 i beleive. Came in with rs00 g4 starter. It doesnt start with 3x lock. I have to wake it by unlock(1x) then lock (1×). To lock it without starting it have to secuence this. Lock-unlock-lock, anoying. Sometimes not tone fast and starts. How is the proper way to connect this wires. Have connected the green wire on the starter to the lock in my car. I got all the kit from fortin. Even that the starter is crimestopper's, all the kit was sent from you as one system together. Need assistance in hooking it up prperly.

where does the A8 (dark Blue) wire connects on 2015 Nissan Armada Intelligent Key?

Mon, 30 Apr 2018 08:58:50 +0000

I just want to make sure that the meant by "The Driver Door Pin" where the A8 Dk. Blue wire connects is that switch located at the body frame and controls the inside capin lights?

is this is the correct interpretation?

Thanks

dark blue wire, driver door trigger - does not work

Sun, 28 Jan 2018 00:01:56 +0000

I have a 2011 nissan rogue intelligent key, I installed an evo one, everything works perfect, except the trigger of the driver's door (auto lights shut down ) dark blue cable, connect this cable to the negative of the door trigger, exactly as the instructions say , but I have the problem that when starting the remote start the vehicle turns on but after 2 seconds it turns off, check the problem and I find that when the remote starter start the dark blue wire gives a constant negative discharge and the sensor of the door trigger shows as if the door were open, I do not really understand what this dark blue wire is for and what function it has, disable it and the car lights normal, my question is what should I do or what is the problem, or I must configure thanks.

Are Lock unlock A2 and A3 optional 2010 altima PTS EVO All

Sat, 13 Jan 2018 19:49:39 +0000

If A4 and A5 are hooked up, do A2 and A3 need to be hooked up, and vice versa?

2002 Ford Focus / Key-Override-All / Will Not Program

Thu, 28 Dec 2017 22:21:53 +0000

Installed a Key-Override-All with a Crime Stopper 'CoolStart RS4-G5'. The Crime stopper works great with a key in the ignition only to satisfy the transponder.

I have tried several time to program the Override unit with no success. I am using Connection (1) with the Data Link. The RX,TX and IGN wires are connected directly to the ignition switch transponder. The Blue wire is connected to the Yellow/Black on the Crime Stopper (Ground When Running (Bypass Module).

I am using Program (2). I press the programming button and plug in the 'Black Connector' and the (6) pin connector. The red light comes on. I than program the keys and than hit the remote start. The red light blinks (3) quick blinks and thats it. The car never remote starts with teh 'Override' however the car will remote start and perform predictably as long as there is a PATS key in range of the transponder ring give me the understanding all is will except the 'Override' module.

Can you tell me what I am doing wrong?

2010 RX350 Evo-All PTS Will not program or start

Mon, 04 Dec 2017 09:38:57 +0000

Hello, I have the Evo-All for a 2010 Lexus RX350 PTS

I wired the unit to guide 29991

It was programmed for me with the following oprions (I do not have a programmer):

C1, D1, D1.6, D2, H2

When in programming mode, step 4, the blue light does not flash after pushing the PTS twice, I just get a flashing red light. If i then push the program button once, I get the flashing blue light Push it again, I get the blue and yellow flashing light.

The car does not start but and the red light eventually flashes 3 times.

I have checked my connections four tiems and tried the program mode many times.

Than you for any help you can provide.

I cant get remote starter installed correctly. Only get through step 6

Sat, 18 Nov 2017 21:10:49 +0000

2016 jeep cherokee. I make it through step 6 but when I make sure the dash light is off and insert the key on step 7, the blue light will not come on. '

2010 Kia Soul Programming problem

Sat, 11 Nov 2017 16:07:55 +0000

Having an issue with 2010 kia soul with normal key, wired up correctly but has no immoblizer wire, do i need to connect red connector to white connector wires still. Instructions aren't very good on this point. It says "US models: if the (~) Data wire is not present the vehicle is not equipped with an immoblizer. For CAN functions use programming #2. I have tired programming to #2 and blue light is on then wihen I turn the key on blue light goes out and doesn't flash at all but when I turn the key off blue light comes back on. It does not flash at all. Please Help. No remote start installed. Using as standalone. CAN Bus wires good 2.5v on each at all times.

(-) parking light

Thu, 09 Nov 2017 15:27:55 +0000

2011 Dodge Ram 1500 gas. Do you clean some of the wire sheath off of the white wire at the light switch to be able to solder the 1 K OHM resistor on? Not sure what to do!!!

(-) parking lights

Thu, 09 Nov 2017 14:16:36 +0000

2011 Dodge Ram 1500 gas. Does the white wire at the vehicle's light switch need to be cut then connected to the 1K OHM resistor and then connected to the harness brown/ white wire. What do I do with the exposed white wire that is left hanging? Do I tape it off?

Takeover with THAR-MAZ1 (EVO ONE or EVO ALL)

Mon, 11 Sep 2017 03:43:21 +0000

When comparing EVO MAZT1 with EVO ALL it shows that Takeover is not available with MAZT1.

Is it the T-harness that conflects with the feature? and will that apply when using EVO ONE with THAR-MAZ1 in 2017 Mazda CX9 Push to start with 3x OEM remote start?

If it does, is there any solution for the mentioned vehicle where OEM remote start, takeover and plug & play is a must for me.

2017 Subaru Outback PTS

Wed, 26 Jul 2017 13:15:21 +0000

If I install an EVO-one into a 2017 Subaru Outback PTS with a smart start (DSM300), will the OEM remote still work once started? Will the Door sensor's still work, meaning can I unlock the car by touching the door handle with the oem remote in my pocket? I really do not want to carry around an after market remote.