Questions & Answers - Questions récentes tagguées 2003

2003 honda accord cranks only

Sun, 19 Dec 2021 14:22:04 +0000

Hello everyone,

I just installed the evo one on a 2003 honda accord but the car only cranks when I try to remote start it. If I put the key near the ignition it starts sometimes. Also, I noticed when evo one is plugged in I cannot start the car with the key..it only makes a buzzing sound. If unplugged, car starts fine with key. Any help is appreciated!

Ps. module was flashed with latest updates.

Firmware Discrepancy

Fri, 03 Jan 2020 21:53:07 +0000

2003 GMC Sierra 1500 Standard Key, with keyless entry and alarm system. Working with an EVO-ALL, date 4/2019, firmware 70.18, using Flash-Link 4 with hardware version 4, firmware 4.05, date 11/2019.

Website indicates firmware minium version is 70.21 for both EVO-ALL and EVO-ONE. However, above min version for the EVO-ONE has note that minium version is 70.18? Does that apply to EVO-ALL as well?

On the installation guide #61111 it states minium version is 70.32!?

Which is the correct firmware? xx.18, xx.21, xx.32?

Using FlashLink Manager 4.51, I am only offered firmware 70.18 for a 2003 GMC Sierra 1500 standard key.

If the minuim is different than 70.18, then where can I download the correct firmware?

And please tell me this is a stand alone remote starter which is going to start the truck with 3x lock on the OEM remote?

Evo-All, smartstart and prostart module install help please!

Tue, 02 Apr 2019 00:34:09 +0000

I recently purchased a smartstart module in hopes to add it to my prostart and EVO-ALL setup I currently have. I don't know what wires go where or if this is even possible as the data link cable seems to feed the prostart module and there is nowhere to plug in my smart start module. Sorry this is confusing I know. The wiring guide describes me plugging in two connectors to the prostart system and one four pin connector into the evoall which I can't seem to see where it goes and what all is involved. Any one help please. If I have it connected to my prostart module do I even need to connect it to. The Fortin bypass module as well?

Will the Evo-One work (stand alone remote start) using factory remotes (Lockx3) on the 2003 Ford F150?

Sat, 30 Mar 2019 20:18:55 +0000

Does the evo one require a rf kit for the 03 f150

Toyota Sequoia2003 Evo ALL+Encore E5 not work

Tue, 27 Nov 2018 13:58:54 +0000

Toyota Sequoia 2003 Evo ALL+Encore E5 dont work-engine start only for 2-3 seconds and off -bypass programm is ok but not work .

wirning cables check many times -whats wrong ??

evo all is not ok for this car ?? thursday customer back to me ,i try use evo key -is ok this bypas ??

How to reset my int-sl+

Wed, 30 May 2018 20:23:23 +0000

I am installing an INT-SL+ with a Crimestopper RS-00G5. I have verified the wiring and programming for a 2003 Chevrolet Silverado 1500 HD. i am unable to successfully program the bypass. I have now reached the flash limit as I was advised to download an older version of the firmware for the vehicle after testing all teh voltages on the wires i.e. pink, purple, orange and black and walked through the programming steps with the technician, How do I get my INT-SL+ reset and when it is which firmware version should I download? In a few of the apparent five firmwares I was able to get the light to flash, however, it always interfered with my OEM FOB, i.e. it wouldn't acknowledge the door lock while connected but when I unplugged it it would allow the key FOB to work.

PS04-G5 2003 Tahoe

Thu, 28 Dec 2017 11:38:23 +0000

Do I need a relay for the starter and do I need a relay for lock and unlock? Do I need to hook up the tack wire? What wires on the Tahoe do I need to tap into for lock and unlock?

Honda Pilot 2003

Sun, 05 Nov 2017 16:12:42 +0000

I /purchase-and-started-installing-honda-sl3-bypass-module-my-20O3 Honda Pilot can-that-module-work

EVO ALL With RF ALL 641W

Wed, 23 Nov 2016 09:42:10 +0000

I'm installing an EVO ALL wIth the RF-ALL 641W. It's unusual for this make 2003 Dodge Stratus Sedan. But the car does not have a transponder system, it use standard keys. It has power locks and trunk, but no factory alarm installed. Also when trying to program the key fobs, on Step 4 when I program button, the blue and red light go out then the blue, amber and red lights come back solid and the antenna flashes blue while the key switch is in the off position. Am I missing a component? only need remote start.