Questions & Answers - Questions récentes tagguées 2014

I need the full installation/programming guide for a remote start system for a push to start 2014 Mitsubishi Outlander

Sun, 05 Oct 2025 18:47:20 +0000

I purchased a remote start system for a push to start 2014 Mitsubishi Outlander last year and didn't get around to installing it. I am now ready to install it, but do not have the full installation/programming guide for the remote start system.

Can you please send me the full installation/programming guide for the remote start system so I am able to proceed? Thank you!

If your Cadillac SRX 2010-2016 suddenly stops starting

Fri, 17 Jan 2025 02:43:30 +0000

I searched and searched for similar cases on the Internet and found this one, written 4 years ago... I tightened these 3 bolts on the fuse board and everything was fixed... "The exact same thing happened to my SRX changed my headlight bulbs and put new battery in. Took the fuse box cover off and the relay out at front of fuse box as there is no room for my big hand to fit in. I figured that if i just removed the screws in the fuse box i could get some extra room so my hand would fit in to get the headlight bulb put everything back together. Went to start car dash lights came on would not start at all spent 3 hours trying to figure out what was wrong. My buddy came over as he worked at a GM dealer told me to push down on fuse box and the car started up the screws in fuse box where not tight as there is a wire harness under the fuse box ."

2014 Cadillac SRX

Wed, 15 Jan 2025 00:55:49 +0000

Hello.The 2014 Cadillac SRX had an aftermarket remote start and evo-all installed. The owner wanted to install a GPS tracker and he removed the ground of the evo-all to connect it to the ground of the tracker.Since then, the car does not start. The ignition opens, but the engine does not start. The remote start elso has no feeling.

2014 Ford Fusion HVAC doesn't turn on.

Mon, 13 Jan 2025 10:46:47 +0000

Hi there!

I have already installed an evo one in a 2014 ford fusion, but the HVAC does not work. When the car is started by remote, only the blower starts working but it does not heat up. The HVAC only heats up when you insert the key and turn it to ignition. I have been reading some articles related to this topic and it is that the 2013 and 2014 Ford Fusions need a reprogramming so that the HVAC works with the aftermarket remote starters. Here is the information and the vin number of the car. Can you help me with a solution? Thanks in advance.

3FA6POG74ER381308

2014 Hyundai Sante Fe Evo One Lte. factory remote

Fri, 29 Dec 2023 17:10:48 +0000

Hello, I installed Evo One Lte in my 2014 Hyundai Santa Fe Sport PTS. The Evo start works great via the Cell app but i cant get the factory remote to start the car. Also, the cell app WILL NOT operate the door lock/ unlock. The list says 3 locks will start and stop remote start, but i cant get it to work. Not sure if its my fault or If factory fobs will not work on this vehicle

Any help is greatly welcome !!!! THANK YOU ALL VERY VERY MUCH

MODULE LED'S DON'T DO ANYTHING WHEN PLUGGED INTO VEHICLE

Mon, 25 Dec 2023 18:18:56 +0000

USED FLASHLINK, MODULE HAS CORRECT FIRMWARE, PLUGGED INTO VEHICLE CORRECTLY, HELD DOWN BUTTON AND ATTATCHED 4 PIN CONNECTOR TO MODULE, NOTHING HAPPENS. NO LED'S LIGHT UP AT ALL. evo-all standalone

2014 Honda civik

Mon, 18 Dec 2023 10:42:01 +0000

Hello. I installed evo-one on a 2014 Honda Civic. I indicated a hybrid - D4... The car switches to a hybrid only when braking. Should I keep this D4 or delete it? 002B04337437

2014 Mitsubishi Outlander Evo-all with evo-start lte and rf642 kit

Fri, 13 Oct 2023 03:10:19 +0000

Hello there guys, i have a 2014 mitsubishi outlander with evo-all and rf442 kit. All works fine and well. And then i added an evo-start lte module. I was able to program it with the rf442 kit. RF kit works fine as before. Then the app for the evo-start works fine as well except for the remote stop/engine off function. Lock, unlock, and remote start/engine on function works. But when i try to do and remote stop/engine off. It doesnt work. Is this a bug on the app? Or is there a programming issue? Again. Lock, unlock, and remote start/engine on works. Its just the remote stop/engine off function that is not working.

any help will be appreciated. Thanks in advance. Btw im using it on ios device.

2014 honda accord

Sun, 09 Jul 2023 15:33:33 +0000

Hello. I installed evo-all(001A07473343)+remote start, on a 2014 accord(hybrid-pts). Remote start opens doors and then doesn't close.

Why does it only honk now when I remote start

Thu, 29 Jun 2023 01:38:34 +0000

Installed evo all with my car telematics with 944 rf kit and has worked beautifully since 2019 with the occasional horn honking when I remote start but I had to remove module and wiring from dash for some audio upgrades now all it does is honk the horn when I try to remote start. Does not try to crank everything powers up as it should then nothing. Thats on first attempt 2nd attempt does even do that. I have since go in and tried to reprogram module as t

2104 Honda Accord Remote Start does not work after programming and Installation

Sun, 18 Dec 2022 14:11:17 +0000

I have all the wires in place, have a toggle kill switch, programmed correctly and did the Flashlink Dcryptor. When I attempt to remote start, it does not start. I see a blue led light the controller when I hit lock on my key fob, but that's it.

I have a 2014 Honda Acord Push Start. With the remote start in place, the car still operates as normal.

How to connect Evo-all build in alarm to 2014 camry pts

Sun, 11 Dec 2022 13:19:23 +0000

Install evo-all with optional mycar module to 2014 camry pts, remote start work but i also want to hardwire shock sensor to evo-all built in alarm. How do i make that happen, thanks

Can you help program my 2014 Ford Fusion with fort3 t-harness?

Sat, 10 Dec 2022 04:29:26 +0000

2014 Ford Fusion with evo-all and fort3 t-harness wont program as standalone. I turn the key to the on/run position and the light just stays solid blue and never flashes.

Remote start shutdown trigger OEM alarm 2014 Toyota Camry PTS

Fri, 09 Dec 2022 08:26:17 +0000

I have installed an evo-all (s/n # 001AO7065000) in a 2014 toyota camry pts, its work as expected except its will trigger oem alarm either by my or timer. I have turn on the disenable alarm prior to start/enable after shutdown option too but its still trigger alarm, every morning the oem trigger right after remote start shutdown getting very annoying. Also i have installed mycar module with the evo-all, mycar module have an option that will detect the alarm (alarm input detection) and push notifications on the phone but i dont see that the evo-all (harness) have any output to horn that i can tap into for the (alarm input detection) to work. Please advise, thank you so much. This is a repeated question and im apologize for that, because its getting very annoying that the oem alarm trigger at 6 am. Im desperately need help

No response from OEM Lock on EVO All with all T-harness

Fri, 25 Nov 2022 13:35:30 +0000

2014 Dodge challenger

After successful Programing including DCryptor process. EVO-ALL does not respond to OEM Lock and doesn't start engine. Installed with T-harnesses for ODB2 and Push Start Button.

Any help is appricated.

2014 ram 3500 will not remote start. Manual transmission

Sun, 13 Nov 2022 01:31:21 +0000

I followed the instructions for the thar-chr7

what else am I missing?

flash link does not have an option for manual transmission

I did not cut the yellow wire

cranks will not start - programming ok

Mon, 24 Oct 2022 12:52:19 +0000

I have a FIAT 500L installed Evo-All and all connections installed as per installation guide, using wire to wire method as remote starter was not listed in options. Performed programming and all lights illuminated and extinguished as described in programming procedure. connected to flash link and decryptor transfer of information was successful. installed bypass to vehicle and all functions are working, however when attempting to remote start vehicle will just crank(as if secret key information is not present) confirmed this was the case if i place the key into the ignition and remote start the vehicle all functions are operating correctly.

Notes: when performing lock/unlock and trunk functions the blue light will flash and function will perform. When i attempt remote start function ONLY the yellow light will illuminate on the Evo.

Any and all information greatly appreciated!

Hello! Which EVO kit and T-HARNESS will fit my car? Nissan Teana L33 2014 Europe.

Sun, 25 Sep 2022 08:10:49 +0000

Эта машина на платформе Altima! Но только европейской сборки. Мне интересно, куплю ли я комплект EVO All NIST4. Подойдет ли распиновка проводки и жгута для моего автомобиля?

EVO-All do I need to order the harness and also do i need flash updater or the existing firmware will support my car.

Sat, 13 Aug 2022 13:32:54 +0000

X-Trail 2014 (Euro) Intelligent Key Push Start EVO-All T-Harness Flash Updater

Can bus faults after 3 trouble free years

Tue, 28 Dec 2021 19:34:06 +0000

Is there any warranty on a the evo device that stopped working out of the blue? My 2014 ram broke down a couple of nights ago and the dtcs state the can bus was not ok. U0001 I removed the can high wire from evo and all issues went away and cleared. I love my remote starter and fob, is there anyway to get this module repaired or replaced ?

2014 Camry fob not working after remote started?

Mon, 20 Dec 2021 14:25:10 +0000

When 3X lock is pressed vehicle starts. Then when started the FOB doesn't work while vehicle is running and have to use the key to enter the vehicle.

I've installed 2 other remote starts in 2013 Corolla and 2016 Tacoma, and after vehicles has started, I can still use the key FOB to unlock the door. I can also click 3X on the lock and shutoff vehicles. But I can't do it with 2014 camry...did I miss a wire? or is this normal operation?

thank you.

2014 Honda Odyssey. Check keyless starting system message on dash

Mon, 25 Oct 2021 19:56:08 +0000

2014 Honda Odyssey push to start. Instillation with Evo one and Thar one Hon8 tharness. Programming and dcryptor went smooth. 3xlock to start and take over are working. Only issue is, I'm getting check keyless starting system message on dash at all times. I've read in the fourm that this light is normal under remote start as the key is not present but should go away once the car is started normal. However in my case the light is on always even when I start the car normally .Any help would be appreciated

Lock and unlock do not work

Tue, 28 Sep 2021 15:17:30 +0000

Just installed an evo-all with autostart command start. vehicle is a 2014 ford focus regular key with lock/unlock button on center console. programed bypass correctly with pressing brake peddle while blue light is flashing rapidly but still dont have lock and unlock functions. sn # 001a07174443

All 3 LEDs on EVO-FORT4 with first key in

Mon, 27 Sep 2021 13:20:01 +0000

2014 Ford Flex Std. Key w/EVO-FORT4 Soon as the fist key is inserted all 3 LED's stay lit solid...even all through 2nd key and back to the 1st key during programming. Vehicle can be put in 3rd key programming mode without module installed (door locks will cycle). Key sense wire is good, ignition chime comes on when key is inserted. Tried programming also without red plug plugged into the module. And checked with tech support using SN to make sure the module was programmed correctly. ?? Thank you.

2014 camry hybrid not starting

Tue, 15 Jun 2021 21:13:21 +0000

I need some help,

2014 Camry Hybrid push to start.

Installed Evo All and using as stand alone remote start only. Blue light on unit flashes with each remote command but vehicle does nothing after giving it the 3x lock command from factory remote

Evo All 03/2019 using Firmwarwe 79.66 Installed with Guide # 70451

and installed with Thar Toy6 harness

Thanks

Steve

Remote starter for 2014 vw passat TDI (diesel)

Thu, 08 Apr 2021 12:35:22 +0000

Do your products work with diesel cars?

Is it necessary to install an additional remote control?

Sun, 28 Feb 2021 07:13:52 +0000

I contacted the local dealer to order any type of Fortin products that could fits my nissan xterra 2014 with standard key, so, the dealr told me that its will not work with my OEM key fob unless if buying an additional remote control from Fortin. Is it true that I will not benft from my original remote ??

2014 camry door trigger not working

Sun, 31 Jan 2021 00:48:42 +0000

Evo-one with thar-4 harness + rf kit, if system is armed/locked I can leave window open and when the door is opened without using remote the alarm does not trigger. Also when opening or closing the doors I get no blue led for canbus? I verified the light blue door data line is connected all the way from the evo-one to the t-harness at the ecu... is this a setting that I am missing?

Worked for a couple days then car wouldn’t do anything

Thu, 21 Jan 2021 07:16:02 +0000

I have a 2014 Honda Accord push to start that I installed the evo one in with the t harness. Everything worked fine for a couple of days and then went to start the car and nothing would work. It was like the car was locked down and had no power. Couldn't unlock doors or open trunk or use the horn from the key fob. After calling a locksmith to break into the car I unplugged the eco one harness and hooked everything back up to how it used to be and the car works fine now. Is their a short somewhere in the evo one or why would it work fine for a couple days and then act up like this?

Does EVO-ONE need a clutch wire for 2014 Ram 3500 diesel manual transmission?

Sun, 20 Dec 2020 04:59:32 +0000

After researching my options for a manual transmission I've determined the EVO-ONE coupled with the THAR-CHR6 was the best configuration for a stand alone system retaining original smart tip key. (Please correct if there is another option) According to another Q&A discussion regarding a RAM 3500 manual diesel, it was mentioned by Antoine Marion that a "clutch switch wire" has to be connected. After referring to Guide # 98581 for the EVO-ONE I did not find any information regarding the clutch switch. Shouldn't this be handled through CAN bus or does it need the clutch wire bonded with an output on the EVO-ONE?

2014 RAM 3500 GAS PUSH TO START . STARTS THEN GOES OFF AFTER FEW SECONDS

Sat, 12 Dec 2020 14:53:38 +0000

Everything works great taillights go on it starts .runs a few seconds shuts off. Or if you unlock door during few seconds of running it shuts off. Does not try to restart. S/N 001A07 177871 for module.

Evo-all 2014 Ford Focus. Lights and dash turn on. No start.

Wed, 02 Dec 2020 22:19:55 +0000

Put in T harness and finished programming portion for stand alone key. Pressed lock 3x to start and dash lights up, radio turns on, then everything shuts off. Engine does not start. Firmware 71.52. Something im missing?

2014 Honda civic pts manual transmission ignition turn on after reservation Mode set

Sun, 22 Nov 2020 11:52:32 +0000

After set the reservation Mode, closed door while engine running then shut off which the reservation Mode set, then ignition will turn on right after shut down, triple check wiring , all okay please help

My lexus es350 2014 goes off after remote start and get in the car then shifting to D

Fri, 20 Nov 2020 16:26:32 +0000

The car is switching off after sbifting to D using evo all with t-harness toy-6 and what are the scenarios supposed to happen with evo all in my es350

immobilizer system service required error after RFK kit install - car will no longer start with original key

Wed, 18 Nov 2020 20:51:06 +0000

Remote start was programmed and worked perfectly, however the takeover sequence only worked by pressing brake and restarting the car with original key.

I just installed the RFK912 and progammed it corectly, the car worked fine starting from the rf remote and original remote. The car both remote started and then after shutting down started normally with the original fast key.

The same night, after starting with the RF key and shutting down pressing the break, the car no longer starts with the original key and shows the immobilzer system service required fault. I can still remote start the car but cant use the original remote to start and drive away. after removing the evo-all - the car shows the same fault. It is stuck where it is.

i tried to use teh dcrypot but it needs resetting - i want to reflash the dcryptor and try starting again.

SN 001A07140493

the car is MITSUBISHI OUTLANDER 2014 EURO

Outlander 2014 - Remote starts works but no Takeover

Sat, 07 Nov 2020 00:34:35 +0000

Hi

i managed to get the remote start to work on an outlander 2014 mk3 2.2 diesel.

I had to use the OBD for CAN1 Hi/Lo as the guide wires did not work, it was after this that I was able to program the evo all correctly and remote start the car.

if I remote start the car, unlock doors with key and then press brake, the car turns off and I manually start it again. This works perfectly and there are no errors.

however, when I press the push to start button to takeover It doesn't work and I get an immobilizer error and electrical system service error on the cluster. Why could this be?

Aux options

Sun, 01 Nov 2020 16:44:09 +0000

Have installed evo all on 2014 Acura mdx by professional installer.

The App evo start 2 have big delay and sometimes not responds at all.

Options like trunk/ windows/ heated seats not working at all. And installer said that this options are not supposed.
What should I do? How to connect aux options to control heated seats and HVAC system?

2014 Santa Fe Push-to_Start was starting fine and than stopped.

Sat, 22 Aug 2020 20:05:01 +0000

After installing the Evo-One it worked perfectly for a day. I than installed the Pink/Black Trunk release wire to Plug D pin 3 in the fuse panel. Remote start still worked right after and than an hour later it stopped working. The remote start doesn't engage the engine when I hit the lock 3 times, I just get the 3 blue LED flashes and it doesn't go red. I checked continuity on all the wires except the can bus connections because I am getting the blue LED and they were all connected. The LED flashes blue every time I press a FOB button, and goes yellow when I turn the vehicle on. Any help would be greatly appreciated, thank you for your time.

I have a Toyota Corolla 2014 Standard 1.6 Liter... What do I choose?

Sun, 26 Jul 2020 07:03:12 +0000

I have a Toyota Corolla 2014 Standard 1.6 Liter... What do I choose?

VW THAR1 HARNESS Install With A Fortin RF Kit

Tue, 10 Mar 2020 15:21:11 +0000

for an EVO-ALL Standalone I am getting ready to add an

RF642W

series RF kit to a 2014 VW Tiguan that already has the THAR-VW1 harness installed. Before ordering the parts, I am trying to figure out if I need the other small T-Harness for the RF Antenna you guys sell on the side (maybe called the RF-ALL?). Does the main harness make this "plug and play" without an extra purchase?

evo all with rfk411 starts 2014 wrangler but immediately shuts off

Mon, 03 Feb 2020 19:06:11 +0000

i have the evo all, updated firmware, corrected the setytings in the flashlink to use H2 for the rfk411,what els eshould be enabled? the jeep starts, runs for 2 seconds and then iss witched off again by the evo all. then the evo has the red and orange light solid.

2014 GTI 6sp starts great but getting EPC light

Sun, 05 Jan 2020 18:30:27 +0000

Replaced a db-all which was acting up plus directed can go to hell :) After hooking up the EVO-ALL i'm now getting an EPC light only when remote starting. If I tap the brake then start with the key, it's fine. Any ideas? Regular key wrapped install.

2014 malibu t-harness installation parking light

Tue, 17 Dec 2019 08:51:12 +0000

hello, i am installing a evo-all on a 2014 malibu and the flashlink software shows A14 as the parking lamp. however the instructions i'm following 63361 state the parking lamp is wired differently with a module i am not using. can i safely use the a14 wire to the suggested gray parking light wire?

Can I use the OEM remote or do I have to install an RF kit on a 2014 tahoe?

Tue, 10 Dec 2019 22:07:45 +0000

EVO ALL with THAR-GM4 stand alone harness. Flashed to current firmware and did the key Dcryptor. The LED lights flashed exactly as they are supposed to during the programming steps. OEM remote will not start vehicle after pressing lock button 3 times.

Fortin Evo one plus RFk942 can’t get it work 6 hours of trying 2014 tundra

Sat, 23 Nov 2019 23:51:24 +0000

Ok here is the basics I have the eco one hardware 2.xx I just updated the firmware in the bypass and the other section. Forgive me I'm tired and can't remember.

"As for the RF kit, the only option you need enabled is RFLF in the remote starter options". As per the instructions "Press and hold the valet switch until the parking lights turn ON, the horn/Sirn will chirp" this does not happen. Step 2 works "Press and hold the valet switch or the antenna but- ton until the Parking lights turn ON, the horn/siren will chirp" But thats to "ERASES ALL REMOTES THAT HAVE BEEN PROGRAMMED AND RESETS ALL FUNCTIONS BACK TO DEFAULT."

i have no idea what I am doing wrong? I can't get past step on by pressing the recently connected valet button to start the RF kit instructions. I also Don't see "RFLF" anywhere in the flashlink updater

my problem is I don't think my valet switch is working. I had been using the OEM Toyota 2 button remote for years.

when I originally installed and programmed the Evo One the valet switch was not installed.. could this be a problem?

2014 Ford edge Remote start works. Key start doesnt

Mon, 28 Oct 2019 17:53:47 +0000

Installed evoall with t harness, programmed and remote start works. However, if I try to use the KEY ONLY to start it won't. Nor will the car shutoff after ive remote started and inserted key. Remote start WILL ONLY shutoff using the lock unlock lock sequence.

Will any of these products work with OEM remote starter already installed

Fri, 25 Oct 2019 15:14:34 +0000

Hi,

I have a 14 Ram 1500, which already has a factory installed remote starter. I'm looking to switch over to Fortin, and use a MyCar RFLink. Can you suggest which product/products i could use to make this work.

Thanks!

Jesse

2014 Chevy Cruze dash lights up but no crank

Sun, 07 Apr 2019 13:06:35 +0000

I installed my EVO All (Service# 001A06 853981) in my 2014 Cruze. When I push the OEM lock button 3x, the dash lights up but the car does not crank. All doors, trunk, and hood are closed. Options C1, D1, and D2 are all ON.

What will work for a 2014 expedition

Wed, 20 Mar 2019 20:28:22 +0000

2014 expedition

2014 CAMRY G-KEY, WITH EVO-ONE+TOYTHARONE-2+RF-642W: REMOTE STARTER STOPPED WORKING OVER-NIGHT.

Sun, 10 Mar 2019 15:32:12 +0000

Hi everyone,

My vehicle: Camry 2014 with G stamped keys.

Services #: 002B07 318660 EVO ONE

Last week, I installed EVO-ONE with Toy-thar-one-2 harness following guide: #76661. I also have the RF642W added on because I knew my car needed RF-kit to remote start (OEM 3X LOCK not supported).

I installed them through, got them working. RF remotes started my car just fine the first night (about 15 F degree outside atm). Unfortunately, they both stopped working the next morning due to no reason or change (45 F degrees atm). The car would just crank when I remote start and then stop. During the cranking, as soon as I put my G-key in, it starts just fine. Normal key-turning starting worked.

I then re-flashed my Evo-ONE and re-programed it into my car. They worked at first and then stopped working the next morning all over again. This time, outside temperature did not change much. So I guess it must not have anything to do with the cold-start feature. I think maybe my Evo un-learns programs itself? May it be the cause here?

About my installation: As I follow the instruction, I have my installation done with successful programming. At Flash-link step, I updated both By-pass and remote starter to the most current recommended versions: 79.51 and 1.24. I left all options as recommended by the wizard too. One thing I noticed, the guide wanted Function 2 in Remote Start to be in Mode 4 which it says "+ Start 2 E1, + Ignition 2 E2". However in Flash-link, Mode 4 shows as "White (E1) START, ORANGE (E2) Ignition 2". I dont know if the difference would cause me the problem.

Thank you a lot!