Questions & Answers - Questions récentes tagguées 2016

2016 KIA K7

Tue, 20 Jan 2026 11:53:26 +0000

Hello. I installed Evo-One on 2016 Kia K7 (on liquid gas...with start-stop).. I specified 2017 Kia Optima in the manager. The EMS wire was behind the passenger kick panel in the red connector on the bottom, second from the right. Behind the fuse, the ignition wire (ON) was pink...the ACC wire was white...the starter wire was yellow with a black stripe. The CAN wires were also located behind the fuses in a small connector... yellow and black... blue and orange. Everything worked well, but after opening the door, when I pressed the brake, the car stopped... When I pressed the start-stop button, the radio turned on, and the start-stop button also showed a yellow LED, but the car stopped when I pressed the brake.

I didn't use the ACC-2. It was blue, behind the fuses. The customer left satisfied, but I'm wondering what else can be added to prevent the car from stalling when the brake is applied?

If you could please send me the serial number of this Evo-One...I usually write down the numbers in a journal and now I forgot to write them down...

Fortin evo-all flashes parking lights 3 times and not started

Wed, 05 Feb 2025 15:14:55 +0000

I released the button on red. Pressed the button once. Turned on the ignition. Red blinked 10 times and blue started blinking. Turned off the ignition. Then released it on blue and after turning on the ignition blue started blinking (as expected). Pressed on the remote 3 times (blue reacts). Red turned on and after 10 seconds red blinked 3 times and nothing else.

2016 camry Hybrid

Wed, 05 Feb 2025 11:46:52 +0000

Hello. On 2016 Camry 2 pcs Evo-All I wanted to be programmed and on both after turning on the ignition after 10 seconds the red LED starts blinking. 001A07579416

If your Cadillac SRX 2010-2016 suddenly stops starting

Fri, 17 Jan 2025 02:43:30 +0000

I searched and searched for similar cases on the Internet and found this one, written 4 years ago... I tightened these 3 bolts on the fuse board and everything was fixed... "The exact same thing happened to my SRX changed my headlight bulbs and put new battery in. Took the fuse box cover off and the relay out at front of fuse box as there is no room for my big hand to fit in. I figured that if i just removed the screws in the fuse box i could get some extra room so my hand would fit in to get the headlight bulb put everything back together. Went to start car dash lights came on would not start at all spent 3 hours trying to figure out what was wrong. My buddy came over as he worked at a GM dealer told me to push down on fuse box and the car started up the screws in fuse box where not tight as there is a wire harness under the fuse box ."

doors unlock with start and radio stays on after starter shut down

Wed, 15 Jan 2025 19:03:01 +0000

I have an EVO-All installed in a 2016 Ford Focus standard key as stand alone unit using FORT4 Harness. the car will start with lock - unlock - lock but the doors unlock when starter engages and remains unlocked unless i manually lock it. when the unit times out or i stop it with the command the radio stays on.

unit is 001A07414606

green/ purple is cut. green-white going to 0volt side and green-red going to 12volt side

white black tapped into grey-yellow

white tapped into purple-grey.

Any help would be appreciated

Edit: I turned on lock after start in the settings and it relocks now. when shutting down it will unlock then lock twice and radio still remains on

2016 ESQUIRE

Mon, 13 Jan 2025 09:59:51 +0000

I installed Evo-All on a 2016 Toyota Esquire (right-hand drive PTS). In the manager, I selected 2017-2018 Tacoma. I connected the CAN wires in the instrument panel connector (blue and white)... I didn't even need to connect the ignition wire. I connected the wires for the parking lights to the steering wheel... (pink and purple).

Program RFK-411 Remote with Evo-One-KHY2 - 2016 Kia Optima

Sun, 05 Jan 2025 16:12:34 +0000

Hello,

I'm experiencing difficulties programming an RFK-411 remote with my EVO-One-KHY2 system installed in a 2016 Kia Optima (US model).

Here's what I've done so far:

Installation: I followed GUIDE #91351 to install the T-harness and EVO-One unit.
Firmware: The EVO-One has the latest firmware for my vehicle (updated via FlashLink).
Programming: Since my car is the US version without the (~)EMS COM cable, I used PROGRAM: 2 to program the EVO-One.
Remote Pairing: I followed GUIDE #68771 to connect the RFK-411 remote, but have been unsuccessful using both the ignition switch and valet switch methods.

The Problem:

The instructions state that the blue light on the RF antenna should flash with each brake press, but the blue light does not respond. This prevents me from completing Step 4 of the programming process.

Troubleshooting:

I've confirmed the red light next to the yellow wire on the EVO-One is off, indicating it's not in locked/armed mode.

It seems the EVO-One is not registering the brake presses, which is preventing the RFK-411 remote from being programmed.

Hyundai Elantra 2016 Evo-One with Standard Key PATS

Sat, 28 Dec 2024 22:40:04 +0000

Canadian version with the immobilizer and harness THAR-ONE-KHY2

Firmware updated to latest.

Programing process completes. Yellow LED method

Question I have is....

I'm not clear with what the manual means by cutting.

A20/D4 and A10/D6 from the blue PATS ~ wire....

A10, D6 and the blue PATS ~ is tapped into the blue PATS ~

A20 to D4 is connected together...

Did the manual mean I have to use A10/D6 from the blue PATS ~ wire by breaking the connection of the blue wire from the connector

side then connecting it back to the blue PATS ~ using A20/D4 back to the blue PATS~ ?

Is this what I am supposed to do?

2016 Ford Transit No PATS Transponder Keys. How to Program EVO-FORT4 to vehicle?

Fri, 27 Dec 2024 10:42:56 +0000

2016 Ford Transit No PATS Transponder Keys. How to Program EVO-FORT4 to the vehicle?

2016 Nissan Altima PCM humming sound and park lights staying on

Thu, 07 Nov 2024 20:47:41 +0000

Installed compustar alarm with remote start using a EVO-NIST4 and diagram75491, d2d cable being used. For some reason the PCM is humming and the park lights are on, what can be the issue? Do I change out the power wire fuse to a 1 amp since it comes with a 30 but I am not using those, just the D2D as the diagram says.

Dcryptor limit has been reached for this car

Mon, 09 Oct 2023 10:07:13 +0000

Evo one. SN# 002B04 331970

Please reset

The car does not start

Fri, 14 Apr 2023 03:35:54 +0000

I connected the wires yesterday

But I did not connect the device because it needs to be updated and the Fortin FLASHLINK4 has not arrived yet.

I tried to start the car today but it won't start.

?for the car to start Should the EVO-ONE be connected after connecting the wires

2016 Chevrolet Malibu standard key Evo One

Tue, 18 Oct 2022 18:00:20 +0000

Hi guys. Do you know if there is any solution for the 2016 chevy malibu limited flip standard key? It happens that all the connectors match the 2015 connections but the colors do not. I would like to install an Evo one with RF kit. I've been looking on the website but I don't see anything for this car specifically. Any recommendation? Thanks.

2016 Audi A6 FlashLink Manager says it needs a key

Fri, 22 Jul 2022 22:26:29 +0000

When I go to flash the Evo-One to firmware 60.10 as requested, the Module Flash page (summary) says Key Sacrificed = 1. According to your website the Evo-One doesn't need to use a key. Is the FlashLink Manager just not showing the correct Installation Method?

Lights not coming on on evo one

Fri, 08 Jul 2022 23:55:13 +0000

No power to evo one on a 2016 4Runner. I already check all the wiring and there's power coming from the ignition harness. But when I try to program it there is no lights coming on at all on the evo one.

2016 outlander

Wed, 02 Mar 2022 15:08:53 +0000

I want to install evo-all on 2016 outlander(PTS...standalone). On the car, the module can not be programmed. After opening the ignition, the blue LED goes out and a lot of errors are written in the devices. The module I reflashed several times (001A07311845). I also tried another module ... Some kind of Japanese autorun PZ 113-04221 was installed on this car earlier P.S. When trying to program, the ignition does not turn off unless we disconnect the CAN connector When I turn on the ignition and wait for the blue LED to start flashing, then it writes errors ... and the ignition does not turn off with the start button if I do not remove the CAN connector from the module. And the blue LED is not visible (when I remove the CAN connector and turn off the ignition, the blue LED lights up ---

16 Tundra, Evo Key, no start

Fri, 10 Dec 2021 00:11:37 +0000

Used connection 5, programing 3 in manual. Wires were easy to find, did not use key sense. Believe truck does have a factory alarm (If that matters), it does have a factory keyfob. Programming does what it says it will do. Remote start is a Viper. Everything remote starts fine if I leave the key in the ignition. If I don't, security light blinks and remote start doesnt work. I have the flash link and everything was already updated, and it didn't give me any options to change or adjust anything. Just update.

GWR is connected to the Viper. Only the red light comes on the EVO Key if I remote start it. Is this normal? I'm sure im forgetting something.

Fob doesn’t open car after remote start

Wed, 01 Dec 2021 05:57:59 +0000

I installed an EVO ALL on my Passat 2016 automatic transmission with OEM fob, it remote starts with no problem, i select 15 minutes option, but when I try to unlock the car with my fob it doesn’t respond, I have to wait until car stops then unlock it, also I did try opening the car with the key lock and the car stops when I open the door. Is any especial configuration to make the fob works while the car is running on remote start?

2016 A6 60.06 firmware loaded but module requires 60.10 for Dcryptor

Fri, 29 Oct 2021 18:47:19 +0000

When i plug in the EVO-ONE and load for a 2016 A6 it is recommending firmware 10.06 and shows that it requires a key to remain in the vehicle but looking at your web site using the EVO-ONE with firware 10.10 you can do it with the DCryptor. I want to confirm what way is required for this vehical and if the 10.06 version is capable to "learn " the key?

THAR-ONE-SUB2 & EVO ONE on 2020 Subaru WRX PTS

Sun, 14 Mar 2021 00:31:28 +0000

I have installed the THAR-ONE-SUB2 in my US WRX per the instruction guide, page page 7/11 T-Harness - Automatic & Manual Transmission
https://cdn02.fortin.ca/download/98951/evo-one_ig_rto_bi_sub2_wrx_2019_pts_b_98951.pdf

ASK:
1.) Why is the car not starting with the Yellow/Red and Yellow/Green separeted per the installation guide
2.) Does my US WRX have to follow the Canadian Vehicle steps, if yes why and if no what is the difference

Installation was simple as mainly 2 connectors and areplug N play. I master reset my Evo One, flashed the 2020 WRX firmware and follow the programming steps on page 8/11. When I get to step 5 to start the car, the car starts and shuts off immidiately, eventually not even turning the starter. The lights on the Evo One stay solid for Red and Blue and programming does not complete to follow up on the Dcryptor part. After a little troubleshooting I found that I can get the car to start if I reconnect the Yellow/Red and Yellow/Green wires I cut eariler making the car at least drivable again.

2016 Kia Soul. Remote start isn't engaging. Fortin Evo One

Fri, 26 Feb 2021 17:47:11 +0000

Having problems with the Evo One not kicking the remote starter on. Programming was did right Im assuming, the can connections are correct assuming becuase i was getting the flashing blue led and such when programming. I do not have the EMS wire so i did use option 2 in the installation diagram. Hit the oem remote 3 times but nothing. Not sure what needs to be checked in the firmware updater though. Kinda stumped and help would be appreciated.

EVO-ALL or EVO-ONE for a 2016 Kia Soul Standard Key?

Thu, 28 Jan 2021 20:49:02 +0000

From doing a little research it seems that the EVO-ALL does not have the remote start? Thanks for any help.

Which System setup do I choose when flashing my EVO-ALL

Wed, 30 Dec 2020 10:03:02 +0000

I have a 2016 Mazda 6 Automatic Push-to-start. My products I'm installing are EVO-ALL remote start, THAR-MAZ1 harness and 2 Fortin RF642W keys. Which system setup do I choose?

1. Standalone remote starter only

2. Standalone remote starter and EVO-alarm system

3. EVO-alarm system only

4. aftermarket remote starter only

5. aftermarket remote starter and aftermarket system

6. aftermarket alarm system only

Evo-One vs Evo-All

Sat, 26 Dec 2020 11:46:52 +0000

Hello,

Bear with me, I'm new to this. But I have a 2016 Hyundai Elantra standard key, that I am looking to have a remote starter installed in. I was recommended to this site but I have no idea what the differences in the models are. The two that came up when I searched my car were the EVO-ONE and EVO-ALL so my questions are:

1. They are both able to remote start, so what are the major differences between them?

2. What is a t harness and why would I need one?

Thanks in advance I appreciate the help :)

2016 Civic with key doesn't always start.

Tue, 08 Dec 2020 17:14:38 +0000

2016 Civic with regular key using evo-all(sn 001A07 159806) and avital 4115L. Sometimes it doesn't start after sitting for 20 minutes or so(doors locked, factory alarm on). It will just crank. Dash lights come on as normal. Will start on 2nd attempt. Doors unlock on 1st attempt to disarm alarm. Starts fine with key. Any ideas?

Does Evo one support 3x lock to start Ford Transit 250 2016 key start ?

Mon, 16 Nov 2020 21:52:04 +0000

Does Evo one support 3x lock to start Ford Transit 250 2016 key start ?
I saw under features it says in some cases it support 3x lock what are those case ?

2016 Toyota Corolla Evo One

Mon, 24 Aug 2020 18:41:19 +0000

I have used the Toy 8 Harness that came with the Evo One,Module (TOY 8 79/xx/1.xx C1, D5 38.2 Progam Lock).

I followed all the steps and when I plug the 20 Pin Connector in the Evo Module, the noise sounds and the dash board warning message says, TURN LIGHS OFF and when I try to Press the button 10 times, the RED and BLUE LEDs fade out by the time I get to 6.

I can't get Pass Step 3!

I reset it a few times and still the same thing!

I switch the Pins and try to use it as a TOY 3 Harness and the same Thing!

I even Hard Wired the module using the Diagram and still the same thing!

I'm thinking this was a bad Module from the beginnig!

I have listen to TECH Support ideas and tried them and nothing works!

I've made 7 attempts on wire this Evo One, trying different ways and the Module keeps doing the same thing every time.

I'm ready to give up!

Any idea, why this Warning Light coming on?

Do this warning light be the reason why I can't ger pass Step 3?

2016 Toyota Corolla with H key,

Wed, 19 Aug 2020 18:19:25 +0000

After following the diagram and I go through the steps!

When I go to plug the 20 Pin connector in the EVO ONE, it makes a noise like the lights are left on and the Dash Board warning say's TURN LIGHTS OFF!

When I unplug the 20 Pin connector, the noise goes awayand the dash bord warning for TURN LIGHTS OFF, goes away!

I try to program the EVO ONE Module with the noise and TURN LIGHTS OFF, by pressing 10 times, the light stop around the 5th to 6th press and it won't let me get pass Step 3.

I reset the Module and did and Master rest and still have the same problem!

Issues With THAR-GM7 in 2016 Sierra 3500 (guide 91291)

Wed, 11 Mar 2020 21:28:40 +0000

THAR-GM7 EVO-ALL and Crimestopper RS4-G5 (datalink; only wires other than Datalink connector from the starter are power and ground because for some reason the starter would not work off the power provided by the DLC)

Module programmed fine.

Remote start worked several times in a row right after install.

Fast forward to next day, delivery of vehicle--remote start worked one time. After that, the ignition would power up but would not attempt to crank. Tried a dozen times, checked plugs. Then the dreaded "service immobilizer system light" came on the dash and I just about S**T a brick. At that point I tried to start with the key--no crank. Wait 30 seconds, thankfully it started up.

Reprogrammed module (decryptor process and all) Remote start works fine a dozen or so times, I send the customer on his way. Get a call back within an hour that it's doing all kinds of weird things--locks are acting strange (randomly locking/unlocking) remote start will sometimes work, sometimes not. The weirdest issue is that when he starts with the KEY, drives around, stops, turns the KEY off, the truck will continue running UNTIL the brake is depressed.

Could this be a firmware issue? I'm just reviewing the installation manual and it mentions "modules manufactured between certain dates" enable option E5. When I read this during installation I assumed that it was referring to the vehicle manufacture date, not the module. I don't believe the module was manufactured almost a year ago or more, as it came packaged with the THAR-GM7 which just became available.

2016 jetta stand alone installation

Tue, 10 Mar 2020 10:56:28 +0000

I set the autostart (stand Alone) on the 2016 Jetta PTS. Everything works, but at startup the trunk opens. What to do?

Evo one wont program 2016 corolla OEM Key fob

Sat, 29 Feb 2020 19:57:38 +0000

Hi I connected Ignition Harness, then OBDII and then 30 pin connector. I have OEM fob key.

When I am trying to program the Evo-One, till step 4 everything is good, but on Step 5 of programming, it only blinks red led for 3 times and pause again 3 red led. I tried reseting EVo-One but not luck.

I do not have TPMS.

Any help would be appreaciated.

Module appears to pass dcryptor, but still slow flashes blue when installed.

Sat, 22 Feb 2020 19:25:13 +0000

After returning module to truck after Dcryptor processs completes, the module still slow flashes blue when installed. The truck still starts with the key, remotely locks and unlocks, but will not remote start. The module does nothing but slow flash blue. I don't see anything in the instructions or troubleshooting about this problem.

Request for updated install instructions - US 2015-2019 Ford Transit 150, 250, 350

Tue, 28 Jan 2020 10:37:32 +0000

There is a 3rd party selling a prewired 3x factory remote start based on the Evo-All so it would seem that the Evo-All can be wired as a stand alone (can-bus) remote start but there are no instructions for this application / US version of the Ford Transit.

See link:

https://www.amazon.com/Start-X-Remote-Starter-2015-2019-Transit/dp/B07PM8ZVNJ

Install Video:

https://d2y5sgsy8bbmb8.cloudfront.net/f71daf72-8800-4c9c-8e09-2963fdbb1b99/default.jobtemplate.mp4.480.mp4

In the installation video (2m37s) the Evo green wire (door status?) is connected to the vehicle Purple/Green described as the vehicle lock wire. Can this connection be explained?

Also, if this is workable what would be the external trigger wire (ground to start/stop)?

For the Evo-All and Thar-For1 T harness would the following be correct?:

Yellow/Black from T harness to [A1] Yellow on 20 Pin connector
Connect [C4] Can Low Grey/Black to Can Low on OBD II
Connect [C3] Can High Grey to Can High on OBD II
Ground Black from T harness

Looking for instructions on any other connection needed ie. lock wire (&diode) and external trigger

2016 ram 3500 manuel evo-one 8 seconde cranking ne fonctionne pas

Tue, 21 Jan 2020 19:06:43 +0000

j'ai tenté a plusieur reprisede configurer , le evo-one pour qu'il crank plus longtemps , parlé deja a une personne au telephone me disant de selectionner le mode 20.5 8 second cranking , mais selectionner ou pas , le crank est d'environ 2 seconde et arrete , parfois 1 sur 5 le moteur parvient a demarrer, comment je fais pour pouvoir avoir au moin 5 seconde de cranking , tout le cablage est ok , le ready go est ok juste la programmation qui bug , comme si meme je change les parametre ca fait rien quoi faire ?

EVO-ALL 2016 DODGE JOURNEY SHUTS OFF WHEN I OPEN DOOR SOMETIMES

Mon, 16 Dec 2019 01:26:15 +0000

INSTALLED EVO-ALL IN 2016 DODGE JOURNEY, INSTALLATION AND PROGRAMMING WENT SMOOTHLY. SOMETIMES AFTER REMOTE START IT WILL SHUT OFF WHEN I OPEN THE DOOR AND SOMETIMES NOT. THE LAST TIME AFTER I OPENED THE DOOR AND IT SHUT DOWN I GOT IN, TURNED IT BACK ON VIA THE FACTORY PUSH-TO-START BUTTON, DROVE HOME, AND WHEN I PARKED AND OPENED THE DOOR TO GET OUT IT SHUT OFF. WHATS GOING ON WITH THIS SYSTEM, IS IT NOT COMPATIBLE WITH MY JOURNEY.

Lock/unlock and start/stop external input wire locations

Sat, 02 Nov 2019 19:14:02 +0000

Lock/unlock and start/stop external input wire locations

How do I Program standalone remote start on 2016 Impala?

Thu, 31 Oct 2019 12:08:30 +0000

I am doing an install on a 2016 Impala with standard key. Using the T-harness and EVO-ALL standalone remote start. When I get to step 5 and turn the ignition on the red and yellow LEDs flash. I have not been able to get past this step. I did already do as the troubleshooting guide said and plugged the red connector in and let the car run for a minute and then start over. This didn't get me any further.

Evo-One + THAR-ONE-TOY8 - Corolla 2016 - Door Lock Intermitent & Lumières restent allumées.

Wed, 30 Oct 2019 21:50:05 +0000

Bonjour,

Je viens d'installer un Evo-One avec T-Harness TOY8.
Installation en quelques minutes. C'est fantastique.
Par contre, Lorsque le véhicule n'était pas démarré, les doorlocks ne voulaient plus débarrer l'auto avec le Evo-One, j'ai du utiliser le unlock OEM et ensuite, le problème ne semble pas s'être répété.
Pas d'alarme d'origine et pas d'alarme sélectionné sur le module.

La cliente m'informe que ses lumières ne se sont jamais éteintes arrivée chez elle. (Elles étaient à OFF lors de l'installation et elle les a mises à AUTO. (Les Headlights et les Parkings. Pas informé si intérieur)
Elle a due aller à l'intérieur de l'auto et mettre les lumières à OFF pour que le tout s'éteigne. Le fil vert-rouge est-il fonctionnel dans le T-HARNESS TOY8?

Merci.

2016 Mazda CX-9

Sat, 14 Sep 2019 11:29:44 +0000

Installing an Evo One with a THAR-ONE-MAX3. Programming goes through smoothly, decrpyts on the Flashlink fine, re-install, and remote start will not function. I have tried resetting the bypass and decrypting multiple times, checked to insure it is not in valet mode, and re-updated the firmware for both bypass and remote start twice before reinstalling to only get the same result. I have also tried lock, lock, lock and lock, unlock, lock, all times and neither works.

I have not hooked up tail lights or pin switch as they are supposed to be controlled by data bus. If this is wrong please let me know.

2016 Hyundai accent standard key Blue programming light turns off when I turn the ignition on

Tue, 07 May 2019 13:11:38 +0000

When installing the Evo one on my 2016 Hyundai Accent the blue programming light turns off when I turn the car on and the light comes back on when I turn it off have the can wires on the right ones do I need the can wires to use the remote start?What options do I need to change the service number is 002B07144688

Auto usagé avec evo start problème...

Thu, 25 Apr 2019 22:07:53 +0000

Bonjour, j'ai acheté mon Auto usagé au concessionnaire kia. Et l'auto vien avec evo start. Le code actuel est utilisé par l'ancien propriétaire . Donc comment retirer l'ancien propriétaire si j'ai zero possibilités de contact avec lui....?

Merci

Why my remote do not open my doors after my car remote started

Fri, 05 Apr 2019 18:38:24 +0000

My 16 impala starts fine with my remote by i cant open my doors with my remote when it is running,

2016Q5 with push start

Sun, 10 Mar 2019 15:48:56 +0000

I got evo-one, when I finally made the setting as recommended by the installation guide:

c1, D6 and d2 and 32.6 38.2

now it attempts to start and it unlocks the car but it doesn't starts the remote won't work locking and unlocking doesn't work, the lights (blinkers) flash twice every one minute and the blue light stays on.

When I flashed with the latest version 75 something I couldn't get to program on the car the blue light never flash rapidly and it only worked on version 60 any help would be great.

Thanks

Is the DCryptor required for a preprogrammed evo rs chrt6 for 2016 ram 2500

Fri, 28 Dec 2018 12:42:57 +0000

Installation8

2016 Ram 2500 wait to start is not working?

Fri, 21 Dec 2018 19:46:48 +0000

I have a 2016 Ram 2500 Diesel with a EVO-ALL and T-harness being used as a standalone Lock 3X remote starter. Everything is working correctly except for when remote starting it doesn't wait for the "wait to start" light to turn off. I'm using the recomended firmware 74.38 and option D1.3 Diesel mode is turned on. I don't see any option for a start delay. Suggestions?

Trouble with Programing 2016 Nissan rogue Evo All t harness PTS

Fri, 07 Dec 2018 17:23:46 +0000

I'm having trouble with my Evo All with T harness in my 2016 Rogue, I cant tell if i have the correct install guide for stand alone. I'm using #77691 and it does not show use of a fob in the installation but i can't get it to program correctly. In programming directions, I connect the first connector while holding the program button and relese on a solid blue light, then I plug the others in and turn the ignition on. The guide says to push the ignition button twice but my car only has on/ff there is no accesory postion, pushing the button twice tuns the igntion on the back off again. The light never flashes like it says it will in the guide. I have double checked all wire connections.

Also, when I went to look for a troibleshooting guide i put my service number into the search engine and when I press search it redirects me to my account page. Does this mean I need a subscription to view this?

Thanks, Theo Maston.

2016 Legacy no start with remote starter

Sat, 24 Nov 2018 17:40:18 +0000

I installed the Evo One in my daughters 2016 Subaru Legacy Limited with the regular key. I used the "T" harness and wired it as described on the website.

When Lock button is press 3 times, the parking lights flash 3 times. I red in the quick start guide that this means read mode disabled. But could not see where to diagnose this issue.

Programming went fine, All the LED lights did as they were supposed to. Decrypting worked OK.

There are no LED lights lit on the unit at any time while plugged into vehicle. None when hit lock button, none when key is on,

Pressing lock 3 times does nothing, tried unlock, then lock 3 times and nothing.

I did notice the security light on the dash glows very slightly inbetween flashes, and also with the engine running. I connected all the wires as per the wiring diagram The IMO wires are connected at the back of the fuse panel in the White/Blue wire. The Yellow loop is cut as this is an automatic vehicle.

THANK YOU!

NISSAN MURANO 2016 EVO ALL STAND ALONE NOT WORK

Sat, 03 Nov 2018 17:43:16 +0000

Evo ALL stand alone not work to Murano 2017.

Connection all is correct ( diagram 66611) 3xlock works ( blue led flashing),enigine not crank ,dash on and message AWD error,check engie light on.

Decryptor is fine.

If engine start Push to start work fine ,but engine off dashboard still on and need disconet evo all to dashobard off.

I try three difrent modules evo all and problem is still

whats wrong ??

Transit 2016 Evo One Connect Diagram no RX TX

Wed, 03 Oct 2018 11:51:33 +0000

Ford Transit 2016 no connector RX TX - no immo

How Connect Evo One ??

Try Regular Installation and Thar For1 not working

No Diagrams for this wersion -why ??

Why does the car turn off when I open the doors, sometimes?

Mon, 10 Sep 2018 21:56:58 +0000

All the programming went without a hitch, but when I open the door the Truck turns off, sometimes. What would this indicate?