Questions & Answers - Questions récentes tagguées blue-light

Blue light remains blinking when taking key out of ignition

Sat, 17 Jan 2026 05:38:28 +0000

Hi, I bought a kit that had a Fortin evo one. The Thar-ty10 and the thar-toy2. I’ve installed it but I’m running into an issue after the programming. I can program it to the point of the blue light blinking but when I turn my ignition off and take the key out it continues to blink. I tried doing the remote start by pressing the lock three times but it doesn’t work. Any help would be appreciated. I have a Toyota Camry 2014 se with the G key

when i activate the remote start it flashes blue 5 times.

Sun, 23 Jun 2024 23:58:44 +0000

i just bought a mitsubishi lancer and it has the fortin ftx84 remote start put into it, when i activate the command start it flashes blue 5 times, i have read that this is the hood latch. how can i fix or figure out what the issue is with the hood latch?

When i try to remote start after install a blue light flashes on module but Jeep does not start

Fri, 15 Dec 2023 18:38:34 +0000

I finished installing and programming my remote start on my 2020 Jeep Wrangler w/o keyless entry. I have the after market remote start remotes and when I go to start it a blue light flashes once on the module but the Jeep does not start. Dash screen light comes on and so does the lights by the gear selector but that’s it.

Evo one CHR4 dodge challenger 2010 no any action only security light flashing

Tue, 07 Feb 2023 16:45:48 +0000

2010 Dodge challenger SRT with stander key and manual transmition

Module programming okay

blue light flash every press lock

Remote start red light one and give 2 sound then off

dashboard securty light flashing

Evo one with Chr 4 T-Harness

please help

Why won't my Evo-One move past step 4 on programming?

Tue, 10 Jan 2023 04:30:30 +0000

I have verified the correct firmware, proper voltage on yellow wire A1, and correct can-bus wiring.I have constant 12v with a good ground. When I turn the ignition to run the blue led that is supposed to flash 10x's turns off. I installed accordind to the install guide provided through fortin's website.I have followed the troubleshooting guide and get stuck after confirming all 5 steps

The first 3 steps in the programming are very straight forward. If you cannot pass these steps verify the following:
1- Firmware: Ensure you have flashed the correct firmware to the module as indicated in the installation guide.
2- Power & Ground: Verify the module is receiving a constant 12 volts and has a good ground.
3- Yellow Wire (A1): Verify this wire is on the correct ignition wire. Their should be 0 Volts present during the first 3 steps.

If the Blue led does not flash common issues would be the following:

1- Yellow wire (A1): Not connected to correct ignition source.
2- Can Bus Wires: If these are reversed or connected to the wrong can bus wires the module will not program.

2014 Jetta The doors don't open.

Sun, 25 Dec 2022 09:50:57 +0000

I installed Evo-All on a 2014 Jetta (standalone).

001A07363467. By pressing 3 times, the engine starts, but the factory remote control does not close the door or open it. It extinguishes by extinguishing, but the pauses between presses should not be less than 2 seconds. The blue LED flashes erratically between presses.

2016 Hyundai Accent. No immobilizer. Cannot make blue light flash for can programming

Thu, 22 Dec 2022 23:02:25 +0000

I have a 2016 Hyundai accent. Have the Can wires hooked up as shown in diagram. Grey wire is reading 3.18 VDC and Grey and black is reading 2.48VDC. Plug in wires and turn ignition to on/run position and the blue light does not flash. I am using thar-khy2 T-Harness. A1 is hooked up to E5 like in diagram. Help......

Can't complete Step 5 - Blue LED don't Flash. Audi S4 2014

Tue, 20 Dec 2022 16:17:44 +0000

Anyone can help me?

I'm Stuck on Step 5 while programming my EVO-ALL with the T-Harness EVO-AUDT1 on My Audi S4 B8 (2014).

The BLUE LED doesn't begin flashing.

CAN Connections are Good. I Measure round about 3V on the Whit 5 Pin connector between Grey and Grey-Black.

Grey-Black goes to Orange-Brown (CAN-Low) and Grey goes to Orange-Green (CAN-High) like in the Guide described.

I have connected these Cables at the CAN Connector near the Relays at the left bottom under the Driver footwell.

S/N: 001A06905491

Thanks!

EVO-All won't pass Red Light on programming (Step 5)

Tue, 19 Jul 2022 15:03:46 +0000

I've flashed the EVO-All multiple times using both the wizard and Pro versions of the flashlink. No success. I essentially flash the module and it won't program past step 5 where the red light is supposed to turn blue and flash.

No clue where to go from here.

I'm using the T-Harness as well so there's no direct wiring.

Everything is plugged in but LED will not flash rapidly in step 5

Tue, 12 Jul 2022 13:43:07 +0000

Toyota 2016 Prius TOYT6 T harness
I am using the guide : Regular Installation without Take Over with T-harness

Hello, I spliced into the 3 wires that were needed. 2 at the OBD2 connector (ground(4) and +12V(16) and 1 wire at the hybrid ECU connector (+) starter(A16).

I took out the 30 pin main body ECU and plugged in the 30 pin connector labelled B from the T harness into it. I then plugged in the 30 pin main body ECU into the T harness female 30 pin side. Am I missing anything?

I plug in the power wire into the Fortin module while holding the button and I waited until it turned solid blue. I then connected the rest of the connectors into the Fortin module. I pressed the power button on the vehicle twice without pressing on the brake. The blue LED stays solid and does not flash. When I turn on the car fully, the LED blue light still stays on. If I turn off the car, the blue LED light is still on

Blue light won't flash in step 5 in guide 65321

Tue, 22 Mar 2022 19:54:31 +0000

Hi On my 2012 vw jetta manual transmission push to start. I connected everything it told me to connect on the wiring diagram but when I turn the ignition on the blue light turns of but won't flash Please help

I can not get the blue light to flash on the module on the first step of programming

Sat, 05 Feb 2022 13:42:10 +0000

2013 nissan pathfinder 2013 nissan pathfinder

2016 Chrysler T&C blue light wont flash

Sun, 09 Jan 2022 13:58:21 +0000

I have a 2016 Chryler T&C with the smart key (not push button start) I bought a evo all SN: 001A07 047755. Programmed with the link (59.02 Firmware) and Connected the yellow wires together like a guy did on youtube. I get to the step with all the blue light staying solid, and turn on the key and it still stays solid. I cant get it to flash when i turn the key on to program it, any ideas? Thank you

How to get past decryptor programming?

Fri, 07 Jan 2022 23:42:04 +0000

Ive tried taking the battery out and everything it says but it stays on blue. is there anything that could be causing this? did i not hook something up that i needed to? i have a 2016 mazda 3 push to start automatic, using the evo-all with the MAZ-1 t-harness that came with it. installation instructions were not very clear. please help.

2014 ram 1500 evo all chr7 install issues

Tue, 21 Dec 2021 20:30:57 +0000

Ok so not long ago i bought my first evo-all for my truck with a t-harness and intalled/programed everything myself with zero issues and it has been awesome. A few days ago a co-worker came to me and asked me to install the same kit on his truck which just so happened to be the same model and year as my truck so i agreed know it should be a simple deal.

Unfortunatly after the install I have been chasing issue and having problems the constantly. It started with a problem were the truck would intermittently begin to start with the command start and crank for 1 second then suddenly stop with no error lights. I tried to fix this assuming the yellow postive wires connection was bad or loose so I soldered the joint, heat shrinked it and taped it up to make sure it was secure. i tested it after that and had three succesfull starts in a row.

The next morning my coworker came to me and said it did the same thing were it tried to start for 1 second and then stopped. I went back in and varified all the connections and made damn sure my soldered joint was good. I then attempted to reflash the module and reload everything and now when i get to step 8 were you enter the key for the second time and then turn it to run and it should go from red and blue to blue flashing, it just goes to no lights at all. I tried this twice with no success so i continued on and dcrypted the module and tried to start the truck and the module doesnt sense the key.Im at a loss, can you help?

cant get a steady blue light on evo one ram promaster

Tue, 21 Dec 2021 17:14:27 +0000

evo one ram promaster 2020 no solid blue light. checked all wires for connectios they are good. Looking at the wire color info and it shows that there is a second 12+(2) connection but the install guide ony show to 2017. Are there two 12+ connections or not.

2016 Ram 1500 Blue Light won't come on

Sun, 05 Dec 2021 17:30:35 +0000

I am stuck at programming part for Ram 1500 Diesel. I am using THAR-CHR7 harness. At Step 7 where blue light is supposed to turn on, it never happens and only red light is lit. Checked all connections, reprogrammed it as well still nothing, I have Tip Key

Programming will not go past step 8

Sun, 28 Nov 2021 17:07:21 +0000

Hi in step 8 the red and blue light will go out but the blue light will not come on again to flash rapidly like its suposed too. When I turn off and take key out the blue light comes on solid. So what could the problem be as I tried to reprogram numerous times.

2006 Ram 2500 Solid Blue Light goes out when ignition turns on during programing.

Sat, 13 Nov 2021 14:38:46 +0000

2006 Ram 2500 Solid Blue Light goes out when ignition turns on during programing.

Answer: The fix for me was to only use the grey Can wire. i removed the grey with black stripe wire and i was able to finish the install.

Solid blue light...HELP!

Mon, 08 Nov 2021 19:00:34 +0000

2010 Dodge Journey- installing the evo all as a stand alone starter, updated to firmware 74.39 and using a T-harness CHR4. i've connected both yellow wires and cut the yellow wire and attached the yellow/green wire on the ignition side as per the diagram. I've checked the connection several times but each time I only get the solid blue light when programming, what am i doing wrong?

Immobilizer Bypass Module does not flash blue led on lock/unlock command

Mon, 08 Nov 2021 11:36:17 +0000

Hi, I have a MPC (fortin) remote start T-harness kit I bought online for a 2016 Honda Accord Sport with standard key. I followed the directions for the programming part for the Immobilizer Bypass Module and Decryptor went well but for some reason, the module does not recognize the lock/unlock commands to light up blue but it does light up yellow when the key is in the ON position.

2015 malibu solid blue instead of flashing

Fri, 21 May 2021 21:00:33 +0000

2015 malibu. During install at step 9 of step 3 of instructions, the blue light stays solid at the end instead of flashing rapidly as described. Using harness that was included for my vehicle with the order on a evo-all

Blue light never comes on

Mon, 08 Feb 2021 20:50:18 +0000

I get to step five re-insert the key in the red light stays on the blue never comes on at all. I have a 2017 Ram 1500 key start.

2007 Elantra won't program can

Thu, 10 Dec 2020 10:09:36 +0000

I am installing a Evo one remote start in a 2007 Elantra with T harness no immobilizer. After setting the module to Blue and connecting the A1 and C1 harness and turning the ignition on to start programming step 4 - 5 the blue LED does not flash. I have followed the trouble shooting steps and have verified, Yellow wire A1 is correctly connected to pink ignition wire+, the can bus wires are correctly connected to gry/black can low to yellow (pin14) on the DLC and gry can high to white (pin6) on the DLC. I have verified can voltage high at 2.6 and can voltage low at 2.4, I have tried to balance the signals closer to 2.5 but I am unable to make a significant or stable change from those readings.

The led cannot be solid blue in the first step

Sun, 06 Dec 2020 20:58:21 +0000

I bought a EVO-ALL and T-harness for my 2009 silverado 1500. I connectted the T-harness to my truck. I press and hold the button on then EVO-ALL, then plug the 4-PIN data wire to EVO_all. But the led on EVO-All cannot to be solid blue. So I have no chance to release the button. I waitted long time and tried sereral times. Same problem. So I cannot pass the first step when I tried to install it.

One more question, the EVO_All I got shows EVO_RS on the box, not EVO-GM. But the T-harness is Thar-GMt4. Is it the problem. Thanks,

Jeep Grand Cherokee 2015 blue light wont come back on after turning the ignition off

Wed, 02 Dec 2020 21:32:13 +0000

this is a push to start jeep

I followed the steps:

1. plug in holding button

2. let go on blue and then turn the igntion on

3. after i press the button when the igition is on the blue light shuts off

4. turn the igniton off

and then it is supposed to be red and blue flashign but that hasnt happened for me

Jeep Liberty wont start

Fri, 20 Nov 2020 22:27:31 +0000

I bought my Evo-all for a 2009 Jepp Liberty and was told it was going to be flashed for it. I connected the chrt5 wires, yellow to yellow and purple to green with red tracer. I did the programming as per youtube and all the steps worked great.

Now when I press lock 3 times it doesnt start. The blue light flashes when i press the lock button but no start. I suspect it hasnt been flashed. Is there a way to tell if thats the case before I buy the flashlink? or do I have other issues?

Remote start wont program when key in run position

Mon, 09 Nov 2020 14:00:59 +0000

2017 Ford explorer using Evo All and Fort3 harness. Used Flashlink and updated firmware to latest for the Explore. Used the suggested setting. I got it all hooked up. Followed instructions and get the solid blue light. When I turn key to run position nothing happens. Blue light stays blue and never starts to blink rapidly to indicate programming. What have I missed?

Blue LED goes out during bypass programming

Sun, 08 Nov 2020 15:47:33 +0000

2008 Hyundai Sonata Evo-One doesn't have PATS wire so I didn't use red connector and light blue wires from 20 pin connector. I finished all the wiring and checked it million times. When I press programming button and plug the 6 pin connector, let go on blue, connect 20 pin, antenna, valet, and can bus, put the key turn to on position LEDs go out.

I tried turning on option 20.2 but when I plug the 6 pin connector all lights flash then they go out and nothing. I'm I missing something?

EDIT: Turned out my antenna was faulty, everything works great now.

during the programming the blue light doesnt come on

Sun, 30 Aug 2020 15:26:20 +0000

when im trying to program the EVO-all i get to the step where the blue and red dhould be on but the blue doesnt turn on

EVOALL will not learn key code in Jeep Gladiator

Sat, 20 Jun 2020 16:32:01 +0000

Hello. When I power up the EVOALL, I get to where the blue light is solid and when I turn the ignition on, the blue light shuts off. The module is then supposed to flash blue rapidly to learn the key code. The module lights do not turn on or flash. This is a stand alone EVOALL with the T harness. I am at a loss. I checked all of my connections. I have the latest firmware via FLASH-LINK. Thanks in advance.

2013 Lexus GS450h EVO-ALL - light won’t blink blue when pressing lock 3x

Sat, 25 Apr 2020 23:07:55 +0000

I did everything as instructed , connected the CAN Hi and Lo , connected to green wire on push button .

programming was successful, it just doesn't detect anything when I press Lock 3x, no blue light blink.

2009 S4 MANUAL TRANS, NO START AFTER 3X LOCK

Thu, 05 Mar 2020 07:45:30 +0000

Hello,

I have a manual trans Audi s4 2009 keyport Evo One , i have installed the T-harness - yellow line from 6 pin to the clutch bypass (red/blk) in engine bay as per pics, Canbus High and Low installed correctly and the Pink from the 6 pin to the purple/ yellow to convenient ignition out.

I have the module programmed as per intructions and no error. when connect all the plugs and lock the car then try 3x lock to RS nothing happens. I see the module flash with a blue led at every lock and unlock but no ignition.

Evo One S/N 002B04 013291

Thank you in advance!

Stu.

2004 dodge durango evo-one thar-chr5 Blue light doesn't stop flashing

Tue, 04 Feb 2020 19:04:59 +0000

During programming when I plug in the white E 6 pin connector blue light goes out. When I turn the key on the blue light starts flashing. Doesn't stop flashing at step 6. After starting the vehicle with key it, the yellow light comes on and stays on. When i try 3x lock, the blue light flashes once per lock, but does not try to start.

Evo-AUDT1 Step 5 progmg, Blue light won't switch from solid?

Sun, 02 Feb 2020 18:28:41 +0000

I have installed the EVO-AUDT1 as per the I struxtions. Connections are good. When try programming the key learn I can not get the blue light to go out. No. Responsive to the program button push. Also, when I stalled in non programming state all thrre lights flash together. I am under the impression this is pre programed ready to go so I didn't buy the flash link programmer. Do I need to flash this unit?

Can not get past step 6 no blue light in step 7

Sat, 01 Feb 2020 17:05:21 +0000

I have a 2010 ford escape. auto trans and 6cyl engine.

I can not get the blue light to light for step 7. Checked all the can connections and even solidered them. they are correct as the instructions ask them to be.

HELP?

Can not get past step 6 no blue light in step 7

Sat, 01 Feb 2020 17:05:21 +0000

2004 Dodge durango evo one programming. blue light wont stay on on mode selection

Sat, 21 Dec 2019 19:38:56 +0000

So i hard wired everything. In the programming procedure. Blue light wont stay on. I checked everything is all in order. Does anyone know what is happening? Thanks

2018 ram 1500 standard key, blue led not flashing , stays.solid blue.

Wed, 18 Dec 2019 11:00:57 +0000

I follow the steps and everything goes well until the very end when I put the key back in ignition turn to.run. red led.goes out but blue doesn't..blue stays solid and doesn't flash at all. fast or slow like supposed ro

EVO-ALL in 2004 Jeep Liberty will not program

Sat, 09 Nov 2019 08:33:47 +0000

2004 Jeep Liberty, no factory alarm, with transponder key. EVO-ALL is installed with a Compustar CS800-S. Used installation guide #3317, Connection #1, Program #1. Firmware flashed is 74.[38].

I can get the bypass to enter program mode (solid blue LED). When turning the ignition key to ON, the blue LED turns off and nothing else happens. The guide says the LEDs are supposed to turn on and off BLUE - RED - YELLOW in sequence, taking up to one minute. I waited 5 minutes with no lights turning on. Any advice?

Blue light on rf642w just flashes not rapidly during programming of evo all

Thu, 07 Nov 2019 22:22:04 +0000

i have a 2011 dodge ram 1500 i have the evo chrt4 and RF 642w I have two questios

1/ there are two programming guides 1 for the chrt4 and 1 for 642w do I go through both or just one ?

2/ I programmed the evo chrt4 everything is good ( My FOB key no longer works the door lock and unlock meaning its broken but still starts truck when in ignition} When I go to the programming of the 642w the light on the antenna flashes blue slowly ...during programming when key switch is turned to run postion the blue light on antenna is suspose to flash rapidily it does not ,,,Ive flashed the module again everything seems to be right not sure whats going on any help would be appreciated

Pairing. No flashing blights to pair key

Thu, 24 Oct 2019 09:06:02 +0000

Hello. I

've purchased the evo-all remote starter. I've purchased the flash link. Updated the software from the online app. When I plug it in I get the solid blue light, plug all the other connectors, key in ignition to run position, but I do not get the lights flashing to pair the key to remote starter. What is it that i'm doing wrong. Followed all the steps even checked on youtube and I get nothing. Please help.

Thanks

Evo-One wont go into Program Mode Audi A4

Tue, 15 Oct 2019 10:08:17 +0000

Directions say to hold the button down and plug in the red cable/black connector, and the light should turn blue. However my light is always red, will not turn blue or flash any other colors. What am i doing wrong?

I am driving a 2014 Audi A4. According to the directions i should be able to enter programming mode without even being connected to my car, just the PC.

Dcyrptor not working, also cannot get pass step 3 programming

Fri, 27 Sep 2019 00:12:09 +0000

Error transmission failed check usb cable, cable has good connection, but it still gives me Receive ERROR after trying again

Also cannot get pass step 3 after blue light is on, then i turn the ignition to the on position, with no indication of rapid blue lights, please help!

Can bus is connected and good.

Cannot get blue led in 2009 Grand Caravan

Fri, 16 Aug 2019 16:59:03 +0000

I cannot get the programming step. I have the t harness plugged in and the two yellow wires connect together like many tutorials? Is this incorrect? He do not want any other functions other than remote start.

2009 Audi s5 manual evo-one with thar-audi blue led stays solid will not program

Mon, 03 Jun 2019 14:09:54 +0000

2009 Audi s5 manual transmission, keyport and start/stop button with evo-one with thar-audi t harness. The blue led stays solid when the ignition is turned on with the keyport and I am unable to program. I have checked the yellow starter wire connection to the clutch bybass and the connection seems solid. The 12v to the juction box is getting a reading and good. The can high and low are also connected good. The connection for the vehicle is clipped together and the plug for the evo-one is connected as well. The 16pin is also plugged into the keyport.

When I plug the data cable in while holding the program button the led turns blue. I plug in all the other cables, insert the key, and press once WITHOUT pressing the brake. When I press and release the the program button the blue led remains on as if nothing has happened.

Any help please?

Evo one wont finish programing

Sun, 31 Mar 2019 16:30:18 +0000

I have a 2011 Tacoma gkey. I've tried evo all and evo one. When programming I get to the point where the LEDs flash rapidly red and blue. Turn the key on and I dont get a blue led solid or flashing. I notice on the diagram that the obd2 hook up is marked as imo wire.my diagram says its sils. My imo is behind the glove box. Is this what can cause my issue

Blue light on Evo all not link don’t pass of step 4 of programming using a THarr-Hon3

Sun, 03 Mar 2019 13:10:01 +0000

The unit don’t pass from step 4 on programation, on Evo -all at an honda car-v 2016 push to start

EVO All Step 9 blue light does not flash 2013 Cruze

Sun, 03 Feb 2019 10:36:46 +0000

Went through all the programming but when I get to step 9, the blue light does not flash rapidly it just stays lit and does not go off when key is turned off and removed. Thanks!

Updated: Figured it out but I have another question submitted.

Blue light shuts off when turning key to on position

Sat, 02 Feb 2019 16:15:47 +0000

2008 Dodge ram the blue light shuts off when I turn the key to the on position.