Questions & Answers - Questions récentes tagguées bmw-5-series

Evo All on E60 door status signal

Mon, 21 Aug 2017 16:03:25 +0000

Hi,

I've successfully installed viper 3305 with Evo All in my BMW E60 2007, everything was done W2W and all working well, except for the door open/close signal from the Evo All, when I open the doors of the car, any door, the door open signal is not sent to the Viper module, so even when the Viper alarm is armed, doors get openned and closed without the alarm knowing!!! So the alarm does not trigger!!

i tested the Viper module by applying a ground on the "door status" signal, and sure enough the alarm is triggered, so It is clear to me that the Evo All is not sending the signal.

Is this a known issue? what could be the solution?

BMW e60 CAN wires color coding

Wed, 09 Aug 2017 09:50:28 +0000

Hello,

I'm purchasing EVO ALL so I can interface it into my BME E60 523i 2007, I've noticed a discrepancy in the wiring guide you provided.

The guide says that the CAN bus High wire at the car BCM module is Black, and the CAN Bus Low wire is Yellow. However the picture you have associated with this color coding shows that the colors are Green & Orange/Green.

Can you please confirm, what colors are the CAN High & CAN Low in the Car?

INT-BMW2 - Need a breakdown on how the brake wires function during remote start sequence.

Wed, 20 Apr 2016 03:10:53 +0000

I'm trying to solve the no start issue on a 2006 525xi using an EVO-ALL & INT-BMW2.

After checking my wiring several times, I feel I need to understand how the brake circuit on the INT-BMW2 module works before I can further troubleshoot.

In the image below, I highlighted the stock function of the factory brake wires.

A) What I need to know is a breakdown of what each of the 4 brake wires from the INT-BMW2 module are doing during the remote start sequence.

So something like this:

Ingnition on: Brake X & Brake Y @ 12V.

Starter on (accessory off): Brake Y @ 12V, Brake Z @ 0V.

Engine running: Brake X & Brake Y....

B) Also, can I get the actual pin numbers & their corresponding colors for the 14-pin connector on the INT-BMW2? Just want to confirm all the wire colours are in their appropriate pin location.

2006 5 Series INT-BMW2 + EVO-ALL issues & wire colours

Mon, 18 Apr 2016 14:29:40 +0000

Car: 2006 525xi - Automatic
Using INT-BMW2 + EVO-ALL (firmware 4.18) + Viper 4806V (wire-to-wire)

Problem 1) INT-BMW lists the brake wire colors as shown below. My car has a Brown/Gray, but it does not have a Purple/White-or-Purple/Yellow.

Here's a photo of my brake switch harness: (colors from left to right) Blue/Orange, Brown/Gray, Brown/Black, Purple/Black.
Right now I'm guesing to use the Purple/Black in place of the Purple/White, is this correct?

Problem 2) When using the Viper remote, the car will Lock & factory alarm is armed, but on Unlock it will unlock and NOT disarm the factory alarm. Opening the door sets off the factory alarm...

I have hard-wired both of the following wires to the Viper unlock wire:

Also, for CAN wires, I'm using Yellow & Black as per this post: http://fortin.ca/en/qa/3393/can-bus-is-not-working-on-bmw-5-e60-2006
I was not able to find the Green & Orange/Green in the DKP nor the BCM as per instructions.

door status

Thu, 05 Jun 2014 21:31:49 +0000

I installed remote start to my BMW 525 2008 , everything is working except door status and brake pedal

status , what should i do to make them work?

2005 BMW 325I KEY START

Fri, 07 Mar 2014 19:53:53 +0000

I was curious if the EVOALL would work on a 2005 BMW 325I key start I know only the PTS is listed. All I am looking for is can function as it is an alarm that he would like intstalled.

Thanks,

Kurt

CAN BUS is not working on BMW 5 E60 2006

Tue, 26 Nov 2013 23:07:53 +0000

CAN wires:

Can-High- Black -Car Access System under driver dash, pin 35

Can-Low - Yellow - Car Access System under driver dash, pin 26

EVO-ALL does not give the status of the doors on the bus Data Link and analog output. Firmware 78.01, 78.05, 4.09, 4.18. Please tell me what is wrong?

EVO-ALL does not give the status of the doors

Sat, 23 Nov 2013 04:12:23 +0000

Why EVO-ALL does not give the status of the doors on the bus Data Link and analog output. Car BMW 5 E60 2006. Service No: 001A06150305. Firmware 78.01