Questions & Answers - Questions récentes tagguées bypass-program

2013 Juke Key Bypass Programming procedure

Mon, 03 Nov 2025 14:59:47 +0000

Step one says to remove the battery from the fob. I did this, and it never says in all the steps after when to insert the battery back in the fob. what step do I put the battery back in the fob?

Problem in programming

Sat, 15 Mar 2025 11:01:06 +0000

Hi i have evo one and i change in settings on my flashlink 4 the number 6 option it says door lock before and after remote-start it was no so I chose Look after remote-start 8.3 after that when i run my car by the remote my wheels don't turn full only half but when i turn my car by the button it's work fine so I do the reset bypass side and return to the flashlink 4 and the same option number 6 door lock before and after remote-start and I put it back to no like it was and i did decryptor but nothing change the opinion didn't work when i turn the car by remote didn't happend like before it was like door open the closing then the car run

My evo one SN#002B04108420

Flashlink 4 SN#002505 085445

2017 Impreza orbit one Evo-All came in car used

Thu, 20 Feb 2025 12:46:18 +0000

Bought a used car with “Orbit One remote starter & alarm & bypass module”

Starter Vr: 7.1.21 , Evo-All Vr: 4.18

Serice No: 002B07 323505

Was bought without a remote start key, wondering if I am able to program a new key, or remove the entire system and have done by dealer

Why blue and red flashing LED after programming 1st key bypass on Evo All on 2014 Mazda CX5?

Mon, 27 Jan 2025 21:24:53 +0000

I am using guide 62951 to program the Evo-Mazt1 to an automatic push button start 2014 Mazda CX5. I have verified continuity to the door lock data and data key wires. When following the key bypass programming procedure it works fine until I get to step 6 on page 9 to learn the first key. Yellow LED lights up briefly then immediately starts flashing red and blue continuously. I have tried using the flasher to re-save the settings. Have tried taking the battery out of the key/fob. Sometimes it stays blue. Sometimes it flashes red and blue. Any help is appreciated. SN: 00A06 843321

Evo-one 2006 rendezvous no yellow light in programming

Fri, 10 Jan 2025 22:02:34 +0000

Ign on - Blue shuts off red comes on but red does not start flashiing to be able to turn key to start for yellow to come on. When red comes on solid the blue starts flashing but is dim. Red never flashes. Talked to tech support said to try starting when red light comes on instead of waiting for red flashing. Still just does the above. I have Reset, flashed 70.18, started and held in start postion and above repeats. He did say to test purple pin 2 and should be 1.5v. It is .23v and I have seen it fluctuate up to 1.2v while lock/unlock is pressedn etc. I have check every single fuse, put on battery charger, cleaned batt terminal, wiggled wires and still does the above voltage fluctuations. Could it be faulty module? Which I've never had happen in over 15ys of using fortin. Strange the blue light flashes dim after red comes on. Could it be the low voltage on obd pin #2? I've never had on issue with the pk3. Factory radio. No signs of anything aftermarket being installed to disrupt obd2 signal. Obd2 plug in code reader communicates fine and no codes present

2011 Ford E250, stuck on solid Red and Yellow Lights during EVO ONE programing procedure

Sun, 05 Jan 2025 12:28:22 +0000

I finished installing the EVO One on my 2011 Ford E250. Made sure that all the wire were connected correctly based on Guide # 86051. I also installed a relay switch for the parking light the same way as shown in the wiring diagram. I used Flashlink to install the lattest 71.57 Bypass firmware and 1.26 Remote starter firmware. I tried many different troubleshooting steps such as disabled A11 according to the guide and changing the programable output to 2.2 to match the wiring diagram. I also tried older version of firmware to no avail.

No matter what I do, it always gets stuck on solid Red and Yellow Lights during step 4 of the the programing procedure when the ignition is turned on. The car I have is regular key without transponder chip. I tried both the 2 keys and DCRYPTOR programing procidure but both has the solid Red and Yellow issue as soon as the ignition is turned on. Please let me know what I am doing wrong and how I can resolve this issue.

I am in step 1.evo-one hyundai Tucson 2020

Sat, 21 Dec 2024 19:46:42 +0000

I really need help! I connect the module while pressing th button and only get a red ligh no blie no other light ko blinking.
it has been a week trying to solve bit no answer and the instrucctions are soooo confussing. Can somebody PLEASE help me!

Red and yellow light flashig alternately after bypass programming.

Fri, 13 Dec 2024 20:23:34 +0000

Evo One with THarn 5? Nissan Frontier 2016It is three harneses: Ignition main one, Immobilizer and OBDII generic. And also installation harnes with white connection.Flashed many times, tryed some options, it goes OK to the end, when i turn the key off red and yellow lights start flashing alternatly. Wires checked many times. Used instalation guide 79451. Evo One SN: 002B04696651. During programming at the step 8 i have flashing rapidly yellow light, but when i turn key into OFF position, red and yellow lights appear flashing alternately. NOW I AM NOT ABLE TO START THE CAR WITH ITS ORIGINAL KEYS.

Step 11 key programing

Tue, 10 Dec 2024 08:06:20 +0000

2016 audi a3 push to start evo all serial number: 001A07 016953

I flashed the correct software on to unit with the flashlink. I get to step 11 of key bypass-program with r-link, and it says to wait up to 5 mins with solid red light. Then it's supposed to flash yellow, and the flah yellow and red, but the red light just stays lit and never goes past that point. I've tried reseting evo reprogramming to a different firmware, then back to the recommended firmware, but I can never get past that point and have waited up to 15mins. What should I do at this point?

2014 Audi Q5 Evo All not flashing yellow in step 8 of Key bypass programming

Thu, 14 Nov 2024 14:01:54 +0000

Im not able to proceed from step 7 in guide 77151. When it should begin to flash yellow and red alternating it just flashes red.

EVO ALL Stuck in Yellow and Red Light Flashing

Sun, 27 Oct 2024 00:34:31 +0000

Hello,

I am installing this on my 2012 VW Tiguan. I followed the process guide 92511. After decryptor and returning the vehicle, yellow and red LEDs flash, instead of staying on like explained on Step 13.

Now it says my unit (SN 001A07 559614) has recheaed its limit and I am really stuck.

Can you please assist?

Thanks,

Andrew

WHY ARE ALL LIGHTS FLASHING AFTER KEY BYPASS PROGRAMMING STATE. INSTEAD OF RED AND YELLOW

Sun, 18 Aug 2024 04:26:14 +0000

I'm trying trying to install the Evo-all (THAR MAZ1) Harness, at the end of the key by-pass programming stage, all 3 lights flash on the module instead of the red and yellow alone. What should I DO.