Questions & Answers - Questions récentes tagguées compustar-cm6200

2014 Chevy 1500 Anti Theft Triggered Error

Mon, 14 Jul 2014 18:45:27 +0000

Compustar CM6200 CPU and EVO-ALL was used. Problem is that the bypass programmed fine but when I went to remote start, no start and information center reads " Service Anti Theft System ". The bypass I believe has both RED and BLUE LED lights on when remote start attempt.

2014 Toyota Camry G Key remote starter crank but not start

Thu, 01 May 2014 11:15:17 +0000

Hi, my problem is car only crank but not start successful. I use EVO-ALL ( service #: 001A06-336)69 ), firmware: 79.12, installation docunment #8881, compustar CM6200, D2D. All function is working, programming is working, door lock, brake, Tach is working fine, I put a key in front of barrel will be start no problem, a red light is turn on and yellow light is on after that on EVO-ALL when I remote start engine. Any solution? By the way, I try idatalink is working perfect after that because you ready closed, but I need to find out

the reason because I don't want giveup your product. Thanks.

how do you programe fortin protocol on a compustar 6200 for a 2006 civic

Mon, 27 Jan 2014 19:39:38 +0000

hi i have a fortin evo all and compustar cm6200 , but i have read on your forum that you need to program the cm6200 with the evo all protocol ..i have the op 500 and i have already programed the evo all to the new firmware ..

EVO-ALL + CM6200 + 2W4500 Problem in 2011 Hyundai Tucson - regular key

Tue, 14 Jan 2014 18:33:56 +0000

I install a 2w4500 with CM6200 module and EVO-ALL using 'data to data' connection. At the beginning is working perfect but after I try a few time, I can lock the door but can't unlock the door, also the LCD remote control show unlock the door automatic after 5 sec. but door is no response . Remote starter is not working and error diagnodtic flash 5 times means 'foot brake on' EVO-ALL hardware is 6 and firmware is 4.18. Any solution?

2010 toyota venza with PTS will not start using compustar cm6200 and evo all

Sat, 11 Jan 2014 22:44:20 +0000

Evo All service# 001A06282907 Firmware 4.18

I installed the system using guide#8601. The evo all programed fine, the remotes, door lock and trunk work fine.

The tach and hood wires are not required with the evo all per fortin's guide.

I am having problems with the remote start.

I followed the fortin guide and everything was connected as instructed.

I press the remote start button on the remote and the car receives the signal to start. It flashes twice and turns on the dash cluster like is going to crank but it doesn't even try to crank. The odd thing is it turns the dash off and then on twice before giving up on the remote start process. Is like it tries 3 times to start but doesn't crank.

Any ideas?

I tried learning the tach, going tachless and changing the crank time but still did the same.

UPDATE AS OF JAN. 12TH 2014:

I reseted the evo all and reprogrammed. Now the car cranks for 0.5 sec but does not start. Then it does the "dash on and off"3 times again. The remote flashes 3 times after failing to start(the error code for 3 flashes is "doors open(manual trasmissions only) but I cut the green loop inside the CM6200 module to make it automatic.

I tried increasing the cranking time to 1 and 1.5 sec. but still will not start and it only cranks for like 0.5 secs.

I did the tach learn process and was not succesful.

I think this is related to the tach and door pin wires not being connected as instructed in the guide, could it be?

Note: when I start the car with the key the yellow led on the evo all is the one on.

Thank you