Questions & Answers - Questions récentes tagguées dodge

Pairing RFK411 remote kit with the Evo One on a 05 dodge dakota

Tue, 05 May 2026 04:43:57 +0000

I have a 05 dodge dakota, just installed the evo one with the RFK411 antenna kit 1 way 1 button remotes and I cant get the remotes to pair. I have tried the few ways ive seen recommend with no luck. I can not find a pairing procedure for this kit with this system.

2026 Dodge Durango

Fri, 23 Jan 2026 18:09:54 +0000

New vehicle 2026 Dodge Durango is firmware available? Only see firmware/software for 25 Dodge Durango can this be used on 26 model yr?

CANNOT GET EVO ONE TO WORK IN OLDER DODGE DAKOTA

Wed, 19 Feb 2025 23:30:34 +0000

Tried installing an EVO ONE module in my 1993 Dodge Dakota. Manual Transmission. Got all necessary wires connected, module will power on, and allow me to program one remote. Afterwards, it will not respond to anything. The antenna LED will not come on, the module lights would alternate red, yellow, blue. Got the flashlink, updated the module, same thing. At a loss, any help appreciated...

dodge journey 2016

Sat, 01 Feb 2025 10:57:13 +0000

journey 2016 evo one avec chr-7 guide 109611 tout bien programmer le camion part 1-2 fois a distance ensuite ignition allume mais ne demarre pas bouge le module et tout va bien ensuite merci j ai mit la derniere version

What do I need to let the EVO-RS9 on 21 Challenger 6-speed manual acknowledge a pressed clutch pedal for remote start?

Sat, 10 Feb 2024 16:36:20 +0000

Everything sets and works fine. I can stay in the car and activate the remote start, it will go through all the steps twice, but no start. If I stay in the car and do the same steps, the car will start as soon as I press on the clutch pedal.

MODULE LED'S DON'T DO ANYTHING WHEN PLUGGED INTO VEHICLE

Mon, 25 Dec 2023 18:18:56 +0000

USED FLASHLINK, MODULE HAS CORRECT FIRMWARE, PLUGGED INTO VEHICLE CORRECTLY, HELD DOWN BUTTON AND ATTATCHED 4 PIN CONNECTOR TO MODULE, NOTHING HAPPENS. NO LED'S LIGHT UP AT ALL. evo-all standalone

2005 Dodge Dakota ABS, Traction Control And Check Engine Lights After Install

Wed, 30 Nov 2022 10:56:23 +0000

ABS, traction control and check engine light come on every time you remote start it. Everything works fine when you start it normally. Code is U1120 - Lost Wheel Distance Message.

Change Connection location of CAN high and CAN low

Tue, 29 Nov 2022 09:39:08 +0000

Is it ok to change the location of connection for the CAN high and CAN low wires from where I should connect them as shown in the guide to the OBD II

No response from OEM Lock on EVO All with all T-harness

Fri, 25 Nov 2022 13:35:30 +0000

2014 Dodge challenger

After successful Programing including DCryptor process. EVO-ALL does not respond to OEM Lock and doesn't start engine. Installed with T-harnesses for ODB2 and Push Start Button.

Any help is appricated.

vehicle will not stay running

Tue, 01 Nov 2022 17:57:40 +0000

sometimes the truck will not stay running when trying to remote start i have the rf kit aswell. when it happenes it doesnt matter which i use the rf or they factory fob the truck will try to start then shut down a second after firing. ive updated firmware performed factory reset and am still having the issue. everything is installed correctly by the book supplied by yall. to temporarily remedy this i have to unplug the unit then redo the holding down the programing button syncing both fobs which get rather annoying. when it happens the red an orange lights will come on while the blue light very faintly flashes the truck will try to fire then when it shuts off the blue light will flash. then the yellow light will become solid after a second the blue light will flash again and then it resets and tries to start again. also the security light on the truck will flash not sure if thats normal or not. i would like a remedy to this issue other than to keep reseting it every time which defets the purpose of having a remote starter.

I bought the evo-all, tharchar4, and flash link4. What more do I need?!?

Sun, 02 Oct 2022 23:57:54 +0000

I've purchased the Evo-all, thar-char4, and flashlink4, Can someone explain it in caveman terms how I can get my command start installed and working? 2012 Dodge Ram 1500

Evo one only responds when its in valet mode

Mon, 02 May 2022 15:18:19 +0000

Evo one s/n 002B04108567 programs correctly with 2010 dodge challenger standard key wire to wire oem key fob and blue light flashes after when pressing lock or unlock , yellow light turns on when starting the car. The problem is minutes later the unit appears to end in in valet mode , red light on the side near yellow cut wire is on. When I take the unit out of valet mode , red light turns off but I no longer receive the blue light when locking or unlocking the car with the oem fob. When I attempt to remote start the car 3x lock the eed light turns on then the yellow light turns on but the car doesn't crank at all and only attempts to try 1x even though programming is set for 2x attempts. Then I get 4 clicks or flashes from the module. I followed guide #94481 for installation and have tried the basic bear options with my flash link 2 updater on 59.02 and 74 38 and 1 25 firmwares. I notice to anytime I try to run the module on the FL updater the FL updater has to be updated each and every time with 4 05 ? Any help appreciated , no oem alarm

Dodge Journey problem

Fri, 14 Jan 2022 14:41:30 +0000

We did the install of a evo unit 001A07 256829 with THAR-CHR7 for a 2012 Dodge Journey as per instructions .

The remote start works but we can't stop the car until the unit is disconnected , we think there's a problem with the unit receiving a brake signal .

Should we remove the obd2 harness and directly splice onto the canbus wiring or could there be an error in the flashing , key programming or decryptor process ?

Thanks

Can I still use the Thar-chr7 with the ram 2500

Thu, 23 Dec 2021 20:43:05 +0000

I was curiouse to know if i could use the that t harness if it was the same connections and everything. Im wanting to install it on a 22 ram 2500. I know and im fully aware that the decripting process might not work. Would i still be able to flash the evo as a ram 21

Solid blue light...HELP!

Mon, 08 Nov 2021 19:00:34 +0000

2010 Dodge Journey- installing the evo all as a stand alone starter, updated to firmware 74.39 and using a T-harness CHR4. i've connected both yellow wires and cut the yellow wire and attached the yellow/green wire on the ignition side as per the diagram. I've checked the connection several times but each time I only get the solid blue light when programming, what am i doing wrong?

Automatically goes into valet mode while driving

Tue, 26 Oct 2021 13:28:31 +0000

Recently i have noticed that while driving randomly at no precise intervals and regardless of moving or stationary alarm chirps. I found this was the alarm going into valet mode. And regardless if it is already in valet mode it will do it again sometimes minutes later and sometimes 20 minutes later. So far it has never happened right after starting up. The alarm i have is a compustar with the Evo All. Any info or advice is appreciated. Thank you for your time.

2012 Dodge Caravan blue led doesn't flash

Wed, 17 Feb 2021 20:03:02 +0000

2012 Dodge Grand Caravan

Stand alone install with CHR4. yellow wire connected but module still doesnt see ignition (no blue led flash)

Hardware 7.0

Firmware 59.02

S/N 001A07 219238

2007 Ram 2500 Diesel Manual Transmission nothing happens

Sun, 14 Feb 2021 21:04:23 +0000

i have a 2007 2500 diesel with a manual transmission, i have the OEM key programmed but when i go to Remote start, all i hear is a relay click 3 times...also everytime i press the lock button on the key, the blue light is lighting up....

i have to make the comment, that when i program the EVO-ONE on flashlink, the "settings" that are saved on the EVO-ONE shows different than the ones i have programmed/saved. is there a "lockout" or something that i must do?

for instance: i saved the turbo timer to be on for 4 minutes on the fortin flashlink, when i check to see "current settings," it shows that it is off. and so forth.

Dodge Challenger 2019

Fri, 29 Jan 2021 10:43:32 +0000

Hi

Will your immobilizers support keyless autostart(without key chip in car) for 2019 year Dodge Challenger?

Thanks

2010 Dodge Caravan No Start Next Day

Thu, 14 Jan 2021 07:40:47 +0000

EVO RS installed in 2010 Dodge Caravan with the CHRT4.

I installed last night, seemed to work fine. But noticed when the vehicle was turned back on the radio clock had reset. This morning I have a no start condition. Doors won't unlock/lock with remote, key in ingition does nothing. Interior lights, head lights and brake lights work. Additionally, due to ignition problem can't shift into neurtal to move vehicle.

Also could not get the horn to silence as per the Dodge Manual after RS installed

GOOD DAY! WHAT DEVICE DO I NEED TO PURCHASE FOR THE 2005 DODGE CARAVAN?

Tue, 29 Dec 2020 05:35:01 +0000

GOOD DAY! WHAT DEVICE DO I NEED TO PURCHASE FOR THE 2005 DODGE CARAVAN?

Temperature settings 2013 dodge journey

Thu, 17 Dec 2020 12:54:55 +0000

Installed the evo start 2 and when i use phone to start the dodge journey the temperature is set to cold. How do you program it so it will turn on the heat and quit resetting the vehicle to ac? I cant find any options for it on the programmer

THAR-CHR7 or THAR-CHR6

Tue, 15 Dec 2020 20:24:14 +0000

I'm working on a 2015 Dodge Dart, by application I need the THAR-CHR6. I order thru my parts department the EVO-CHRT6 but received a EVO-CHRT7. I tried to do the install anyway but in step 7 nothing change when I insert the key for the second time. Is there a way to modify the T-Harness to make it work so I dont need to wait for the good one? Thanks

cant get horn to trigger or trunk to pop

Mon, 30 Nov 2020 01:22:01 +0000

I have a siren positive connected to E1 thick white wire and siren neg connected to orange/black wire and the siren works. I have the horn wire under driver side dash green/orange wire also connected to the thick white wire. Horn honks when arming evo one alarm but not sound when alarm is triggered. What am I doing wrong ? Which option in #12 should be checked , siren + E1 white - horn, right ? Also I've tried several different wires to get the trunk to pop with no luck ! I'm using factory fob that has trunk pop button. Evo one , wire to wire , no factory oem alarm.

2014 Dodge Journey Tip Key Fotrin Module

Sat, 31 Oct 2020 13:47:22 +0000

which model number and T-Harness fits Dodge Journey 2014 Tip Key (not keyfob for push start) , as I only see push button as a choice in the drop down menu.

Thanks

2013 Dodge Journey automatically unlock when pressing lock button

Sun, 01 Mar 2020 23:49:27 +0000

reinstalled after finding a loose wire and system was working off and on. After reinstalling the alarm, compustar CM600-AS, it is workingfor the most part however now when i press the lock button on the Compustar remote it locks and a second or 2 later it unlocks but alarm is still set. when i press unlock i can hear it pulse twice to unlock.

previously i had done the standalone installing and for the most part had no issue with the exception of the loose wire but this time went with the standard installation. confirmed all the wires are connected correctly and date protocal is correct. i am sure it is a setting just not sure which one i will need to turn on or off. any help will be greatly apprciate it.

installation evo-one on a dodge sprinter

Mon, 03 Feb 2020 00:38:39 +0000

The manual No. 63641 does not indicate with what starts the engine. Does evo-one have an input for starting, as is evo-all (Start / Stop external)?

Starter wire on evo all 20 pin to 2003 dodge grand caravan.

Wed, 18 Dec 2019 15:44:40 +0000

On 2003 dodge grand caravan evo all connection diagram there are three connections fron ignition connector to remote starter not to evo all. Are they necessary because i am using a compustar revo witch has only 4 pin data link connection. So where do I connect the starter wire from my car to evo all 20 pin. Thanks

EVO-ALL 2016 DODGE JOURNEY SHUTS OFF WHEN I OPEN DOOR SOMETIMES

Mon, 16 Dec 2019 01:26:15 +0000

INSTALLED EVO-ALL IN 2016 DODGE JOURNEY, INSTALLATION AND PROGRAMMING WENT SMOOTHLY. SOMETIMES AFTER REMOTE START IT WILL SHUT OFF WHEN I OPEN THE DOOR AND SOMETIMES NOT. THE LAST TIME AFTER I OPENED THE DOOR AND IT SHUT DOWN I GOT IN, TURNED IT BACK ON VIA THE FACTORY PUSH-TO-START BUTTON, DROVE HOME, AND WHEN I PARKED AND OPENED THE DOOR TO GET OUT IT SHUT OFF. WHATS GOING ON WITH THIS SYSTEM, IS IT NOT COMPATIBLE WITH MY JOURNEY.

while programming, blue light goes off at key on

Sat, 14 Dec 2019 18:55:53 +0000

installing standalone evo all (EVO-CHART5) with T harness on 2007 dodge durango. I have made the connections purple from T to Green/ Red (a18), yellow from T to yellow(a1), plugged T harness behind key switch. Used flash link 2 and selected options c1 for lock 3 times to start. I plug in black plug to evo all while holding in the button and release on blue, plug all connectors in and when i turn the key on the blue light goes off. I have 12vdc on the yellow wire (a1). Turn the key off and blue light comes back on. I have verified my all my connections. I even did a master reset, downloaded the latest firmware etc. what else should i do?? I have installed 4 of these so far and i have never had this issue with the others.

CAN HIIGH\LOW

Thu, 05 Dec 2019 16:55:42 +0000

The installation guide for my 2018 Challenger shows the back of a white module for the Can connections. How do I make this connection?

My installation guide said I need hardware 6 in evo all but I have hardware 7 in evo all

Fri, 29 Nov 2019 01:08:28 +0000

My installation guide said I need hardware 6 in evo all but I have hardware 7 in evo all so can I use that or i need to change it with hardware 6

2006 Dodge Ram Diesel

Tue, 26 Nov 2019 18:42:25 +0000

Hello i have a 2006 dodge ram 2500 5.9 cummins. I just got the EVO-CHRT5 kit for remote start only and tried installing it as per instructions and nothing worked. I found a youtube video where some plugged the t-harness in and spliced the two yellow wires together and spliced the purple wire with the green/red from the 20 pin connection. the truck horn cherps, and fuel pump turns on but gauge cluster wont work and truck wont turn on. I have the flash like and updated it with the newest version and activated the d.1 setting for diesel trucks. Any help would be much appricated.

Evo-CHR6 Programing Issue

Sat, 16 Nov 2019 19:10:45 +0000

The module is not currently cycling through the various leds. The module lights up red, yellow, and blue but will not go to the all yellow for programing steps. The wiring currently hooked up is Can Low, Can High, T-Harness, Ignition, and parking lights. The kit included a valet switch and hood pin which I did not install. Does this need to be hooked up? Please help.

2018 Dodge Journey - Evo ALL THAR-CHR6 - Guide # 73591 - CAN H and CAN L alternate location?

Mon, 28 Oct 2019 15:44:25 +0000

The guide states that the CANH and CANL wires are up in the CAN junction block. I've located the wires, and I can just get the plug out but once I do, there is not enough wire slack to be able to splice into them. I've seen people mention thay've gotten this to work, but I do not see how.

I know that there is a CANH and CANL in the OBD2 port, as they are there in pretty much all vehicles since it's an industry standard. Is there any reason I cannot splice into those?

Vehicle won't stay running after the Evo-All start the van, it runs for about 2 seconds. 2011 Dodge Grand caravan

Thu, 24 Oct 2019 10:29:36 +0000

Vehichle won't stay running. I have updated it and used C1 and D1 enabled. If I bypass the key it will stay running but that would be a annoying having to lock the van two times to turn the engine off. I have the hood part installed and the yellow wire hooked up too. The OEM key does everything else I just wanted the remote start.

2018 DODGE JOURNEY Unable to find pink/white 9v ignition wire.. GUIDE #73591

Sat, 19 Oct 2019 19:09:15 +0000

Going through the guide, I have removed the driver side kickpanel and there is a huge bundle of wires, and I've looked through them and found two pink/wire wires, niether of which are 9v. One is .05v the other 12v. Am I just missing it?

:EDIT: I dont know why the pictures wont show up, they appear fine when creating the post and if I make them any smaller, they'll be hard to see.

2018 Dodge Journey Can high and can low location. Guide #73591

Sat, 19 Oct 2019 16:04:55 +0000

I see that there are can bus connection at the junction block per the pictures on the guide and from wire colors, but I cannot see for sure which are the white green and white blue connections. Is it possible for me to access these from the obd2 Port? I'm using the thar-chr6 harness. I see that pin 6 is can high, and pin 14 is low. Is it possible to use these? On the obd2 Port I mean.

:EDIT:

There are no white/green and white/blue wires where the guide says they are. I'm at a standstill until I can figure this out.

The guide might need a rivision, I also cannot find a pink/white ignition wire behind the driver side kickpanel. The two I found are .05v and 12v, nothing I can find is 9v.

2007 Dodge Dakota Evo CHRT5 hood don't trigger alarm

Sat, 18 May 2019 04:05:46 +0000

How do I need to program Evo All or connect the t-harness so the alarm sound when my hood is open

dodge journey 2012 all programing its ok but dont crank

Fri, 05 Apr 2019 21:31:21 +0000

installed and programmed as indiaca the user manual at the time of pressing the lock button three times only turn on the parking lights and in the module the red led is lit in the same way, please your help to solve this problem,

Got stuck in step 5 on chrt6 for 2017 journey

Wed, 03 Apr 2019 23:19:43 +0000

Ok i made all can high, can low connection on the diagnositic plug an the ignition to the white and pink wire (tested with multimeter) and i cant get the yellow light to red in key programming, are the light blue and light blue and black wires that connect from a10 and a20 to tharness requiered?

Evo-All, smartstart and prostart module install help please!

Tue, 02 Apr 2019 00:34:09 +0000

I recently purchased a smartstart module in hopes to add it to my prostart and EVO-ALL setup I currently have. I don't know what wires go where or if this is even possible as the data link cable seems to feed the prostart module and there is nowhere to plug in my smart start module. Sorry this is confusing I know. The wiring guide describes me plugging in two connectors to the prostart system and one four pin connector into the evoall which I can't seem to see where it goes and what all is involved. Any one help please. If I have it connected to my prostart module do I even need to connect it to. The Fortin bypass module as well?

Will the EVO CHRT5 work on a 2014 Dodge Grand Caravan?

Fri, 15 Feb 2019 21:08:49 +0000

I bought a EVO-CHRT5 from amazon (package is not here yet.) but just realized that it may not be the correct one for my 2014 DODGE GRAND CARAVAN when I was searching around on this site.

Blue light shuts off when turning key to on position

Sat, 02 Feb 2019 16:15:47 +0000

2008 Dodge ram the blue light shuts off when I turn the key to the on position.

Can I use EVO-ONE with 2003 Dodge Caravan?

Wed, 16 Jan 2019 15:01:02 +0000

Being the EVO-ALL can not be used as a Stand-Alone unit it requires an additional remote start system to start the vehicle. Can I use the EVO-ONE to accomplish the immobilizer and start feature on a 2003 Dodge Caravan?

Evo all not flashing blue on step 10

Mon, 14 Jan 2019 16:40:48 +0000

When going through the installation process the Evo all does not flash blue on step 10. All wires are connected with the exception of the hood wire. I have tried firmware 74.32 like the guide suggests as well as 74.18 like the flashlinj suggests.

When programing, vehicle starts as soon as key is turned to ON position

Mon, 07 Jan 2019 18:15:17 +0000

For a 2007 Dodge 2500 Diesel. Had system installed and working correctly, but after a few starts found that I could no longer manually start the truck with the key. Reprogrammed unit, and it worked again for a few more starts, then blew the 2 amp ingition fuse. Replaced the fuse, pulled wiring and checked to ensure all connections were good. Reinstalled. Now, when I try and program the EVO the truck starts as soon as I turn the ingition to the On position with the key. I can turn it off and complete programing by pressing the lock button, but if I try to remote start it it blows the fuse again.

2012 Dodge Caravan will not start with correct programing

Mon, 31 Dec 2018 17:57:02 +0000

I have installed a EVO-CHRT4 on my 2012 Dodge Grand Caravan. I did not connect the lights or the hood switch. Yellow wire have been joind together from the harness to the 20 pin. All steps of the program went good. When I hit the lock remote 3x nothing happens.

Thanks in advance

Dodge Dakota 2008 doesn't Start** CHR5

Thu, 20 Dec 2018 20:30:15 +0000

EVO-All.....reprogrammed Evo-All with Flash Updater....Went smoothly....C1 and D1 enanled along with 3x Lock....Connected Yellow fromT-Harness with yellow wire of 20 pin connector...Mauve wire from T-Harness to green-red wire of 20 pin connector....Programming in truck went smoothly...After flashing Blue Leds, hit Lock on OEM remote got a Beep and flashing Blue leds went off...Tried to 3x Remote start Blue LED went on with each press, but engine did not start....Tried Lock-unlock-Lock but still no response. When started with key , Yellow Led is on!! Master reset and tried again , no response...Each time I attached the T-Harness I had to reset the Clock...What am I doing WRONG?

2017 Dodge Journey Install Guide States I need a Resistor but I don't see where it's used?

Fri, 30 Nov 2018 10:29:12 +0000

I am reviewing the install guide #74201 and on the first page it states that the install requires 1 resistor. But it doesn't say what kind of resistor and the rest of the instructions never mention it. Also on page three the instructions show a wire location with the number 3 in which it states "passenger kick panel" but the image is showing the "driver kick panel" Can anyone clarify these install instructions.