Questions & Answers - Questions récentes tagguées evo-chrt4

purchased EVO-CHRT4 for 2011 jeep grand cherokee

Fri, 10 Oct 2025 18:59:38 +0000

I purchased the EVO-CHRT4 for a 2011 jeep grand cherokee. Installed per instructions, also tried a youtube install. All steps went as required, per instructions. jeep will not start remotely. please help.

FACTORY ALARM COMES ON

Thu, 18 Feb 2021 04:49:26 +0000

I installed the device on my car 2010 Chrysler Town & Country (Guide # 94291 EVO-CHRT4)

and the device works fine, but there are two problems:

1-When I start the car with the OEM remote 3x lock, the horn/alarm comes ON.

2-When the engine is turned off from the OEM remote the car dashboard screen and the radio remain on

any thoughts on fixing that??????

Note: I only connected T-HARNESS EVO-CHRT4 without any other wires to car

2012 Dodge Caravan blue led doesn't flash

Wed, 17 Feb 2021 20:03:02 +0000

2012 Dodge Grand Caravan

Stand alone install with CHR4. yellow wire connected but module still doesnt see ignition (no blue led flash)

Hardware 7.0

Firmware 59.02

S/N 001A07 219238

Do I have to connect this wire ?

Thu, 11 Feb 2021 04:41:56 +0000

In Guide # 94291 for 2010 Chrysler Town & Country there is a wire (D1 Yellow/Green (+) IGNITION in 6 PIN CONN) In the drawing it must be connected with Yellow wire in the T-HARNESS EVO-CHRT4 IGNITION BARREL

My question to you is, do I have to connect this wire? because all the people on YouTube have not connected this cable

my update for a 2012 dodge ram shows a 2015 caravan update, why ?

Thu, 07 Jan 2021 13:59:37 +0000

I purchaed a flashlink update modual and a evo-chrt4 for a 2012 dodge ram. When I went to do a firmware update it came up as a 2015 dodge caravan. How do I update the firmware for my vehicle ?

EVO-CHRT4

Mon, 19 Oct 2020 16:47:01 +0000

Hello,

I'm planning to purchase EVO-CHRT4 for my 2010 RAM 1500 GAS.

I have few questions about the EVO product.

1. Is EVO-CHRT4 the correct product for 2010 RAM 1500 GAS?

2. Do I need Flash-Link Updater even if EVO-CHRT4 is preloaded module?

3. My car does NOT have the RAM Fob keyless entry (Standard Key). Is it OK for programing EVO-CHAR4 module?

4. Guide #94291. Is it corrct guide for 2010 RAM 1500 GAS?

5. I'm planning to add-on RFK411 RF kit for EVO-CHRT4. Is it compatable with EVO-CHRT4?

Thanks.

All LEDs are blinking rather than alternating?

Wed, 05 Aug 2020 00:32:56 +0000

2012 Ram 1500 standard key. after installation and wiring ready for programming, i plugged the data connector I just had all LEDs blinking. the first unit was replaced and i have the 2nd now but still the same, is there a problem on the unit itself or just my vehicle?

my activation key has timed out before i could get it installed in my 2015 Dodge Grand Caravan standard key

Thu, 16 Jul 2020 13:55:50 +0000

how can i get it back?

the leds do not flash they stay lit???2016 dodge grand carvan

Wed, 01 Jan 2020 21:14:51 +0000

leds on module stays on

Evo all starts then stops 2 secs the trys again then stops on 2012 t&c van

Sun, 22 Dec 2019 12:03:07 +0000

Car trys to start then stops

EVOALL EVO-CHRT4 not programming correctly after installation

Thu, 28 Nov 2019 21:45:31 +0000

Installing an EVO-CHRT 4 in a 2012 Dodge Ram pickup. After initial installation (connection of T-harness), unit does not finish programming procedure correctly. On first attempt during Step 4 of the programming procedure the blue LED remained lit with no flashing after key was turned to ACC and then turned off after turning key to ON/RUN. All lights remained off after turning key to OFF again. Remote start did not work. Repeated steps 1-3 three times with same result on Step 4/5.

After reading through help forums, saw the recommendation to reset the unit in case it had been previously programmed for another vehicle. This was done by programming to the red light on step 2 and then holding the program button until all three lights flashed.

Now, unit performs normally through Steps 1-3 but now flashes all three lights when turning key to ON, and does so more than three times. The continuity was checked with a voltemeter and there is no loss of power or ground on the 4 pin data connector. This isn't surprising considering this only occurred after resetting the unit. My best guess is the firmware was reset as well, but my understanding is that then the lights should only flash three times.

Thank you,

Brett

Vehicle won't stay running after the Evo-All start the van, it runs for about 2 seconds. 2011 Dodge Grand caravan

Thu, 24 Oct 2019 10:29:36 +0000

Vehichle won't stay running. I have updated it and used C1 and D1 enabled. If I bypass the key it will stay running but that would be a annoying having to lock the van two times to turn the engine off. I have the hood part installed and the yellow wire hooked up too. The OEM key does everything else I just wanted the remote start.

Cannot get blue led in 2009 Grand Caravan

Fri, 16 Aug 2019 16:59:03 +0000

I cannot get the programming step. I have the t harness plugged in and the two yellow wires connect together like many tutorials? Is this incorrect? He do not want any other functions other than remote start.

Evo CHRT4 and RF642W

Sat, 15 Jun 2019 15:01:15 +0000

I have installed Evo CHRT4 in my Grand Caravan 2018 with OEM key and it's working great. The CHRT4 was flashed for RF. I am now trying to install RF642W using RFA2A following steps on installation guide.

As per the last step on installation guide, I did press & release (-) AND press & release (lock) on RF642w fob, but on CHRT4 it did NOT blink RED and BLUE LED, instead the RED, BLUE, YELLOW LEDs stayed solid on. The fob would sound and show green light [after I press & release (-) and press & release (lock)].

The antenna LED fast blinks (BLUE). I checked wires and everything was good. Can someone help me resolve this? Thank you in advance.

Evo CHRT4 and RF642W 2-Way LED

Tue, 28 May 2019 12:23:21 +0000

Hi,

I just bought Evo CHRT4 and now I am looking to install RF642W 2-Way LED. I wanted to make sure that RF642W 2-Way LED is compatible with EVO CHRT$. Could you please confirm?

Thank you.

Bhavik

Installed EVO-CHRT4 not working.

Sat, 09 Feb 2019 20:09:15 +0000

Installed this remote starter. Got to the flashing blue light when ignition turned on. Turned ignition off and pressed the lock button. Pressed the lock button 3x and nothing. Tried lock-unlock-lock with same result.

Viper smartstart not communicating with EVO ALL

Wed, 06 Feb 2019 10:18:47 +0000

I've installed a VSM350 in my 2008 Grand Cherokee, following the instructions (splice grey wire with black, plug in connector). The VSM350 has been activated by a local dealer and my viper online account is properly set up. I can update GPS information via the smartstart app (this confirms unit is powered up and communicating with the internet properly). I am not able to lock, unlock, or remote start using the app. When I attempt to lock/unlock or start, I receive the message "unlock failed at [time]" I have enabled H4 via flashlink. I live in a major city and the vehicle is parked outside, the issue is not related to cellular coverage; the app reflects that the vsm350 has 4 or 5 bars of signal strength.

I appreciate any suggestions to enable the smartstart to communicate with the evo-all to enable the lock/unlock/remote start.

Thank you

Programming EVO-ALL / CHRT4 with SmartStart VSM350

Fri, 01 Feb 2019 11:51:55 +0000

About a month ago, I successfully programmed and installed an EVO ALL with CHRT4 in a 2008 grand cherokee. The 3x lock would successfully initiate a remote start.

I recently removed the EVO ALL to reprogram it with flasklink to enable H4 (smartstart). Upon reinstalling EVO ALL, I no longer had blue lights. I reprogrammed to the key and got the blue light to illuminate when clicking lock button. I connected the yellow to the yellow for ignition during initial install and that is still the case now. This yellow wire splice is the only wiring i've done outside of installing the CHRT4 harness.

The current issue is that after reinstalling the EVO ALL, I do not get a red light on the EVO ALL after clicking 3x lock. The 3x lock is still enabled in flashlink, in addition to H4 being enabled. EVO ALL was already (and still is) flashed to the latest / best / recommended firmware. Given my inability to remote start with 3x lock before even connecting the smart start, i have left the smart start unplugged until i can resolve the failure to start with 3x lock using the key. I have tried re-flashing the evo-all with latest firmware in flashlink and starting over but am in the same position where i get blue lights but no red, and thus, no remote start using 3x lock.

When vehicle is started via the key in ignition, EVO ALL gets a solid a yellow to indicate the evo-all knows it has ignition.

My question is: What I'm doing wrong or do I not have connected properly to get my red light back after 3x lock so that the vehicle can start. Does H4 prevent use of 3x lock remote start?

2016 Dodge Grand Caravan Headlight Switch Issues.

Sat, 24 Nov 2018 20:12:38 +0000

I installed the EVO-CHRT4 unit in my 2016 Grand Caravan with no issues, but now my Headlights are always on when the car is running. The Headlight Switch does not work and does not even light up as it should at night. My install was just the T harness with no additional modifications. Never even touched the Headlight Switch. Any idea what's going on? All help is greatly appreciated.

Want to confirm a EVO-ALL that's preloaded with EVO-NIST1 can be flashed with EVO-CHRT4 to work on a 2010 Dodge Charger?

Fri, 26 Oct 2018 10:56:41 +0000

Can a EVO-ALL work for any supported car

What to do with d1 yellow wire

Fri, 31 Aug 2018 16:08:23 +0000

Where do I splice in the D1 wire the instruction say to make connection and the other end says cut ignition

do I tie in d1 into the yellow wire of the t harness female plug and tape off the other end of it that leads to t harness male plug?

How do I know if D1 and C1 are enabled?

Sun, 07 Jan 2018 23:15:50 +0000

I thought I bought the stand-alone unit, but vehicle is not starting. The unit seemed to program correctly. I press the lock button 3 times on the factory remote and the blue light flashes on the unit each time the lock button is pressed, but then I get nothing.

Blue light not flashing on Evo-chrt4 setup in 2012 dodge grand caravan

Fri, 30 Dec 2016 09:53:12 +0000

Blue light goes out but does not flash when turning on ignition. Yellow wire connected together. Directions from other troubleshooting say the bus wires are are reversed. Do I modify the t-harness to fix this problem? I have the programmer and ref lashed the unit.

evo all avec dodge grand caravan 2008

Sat, 03 Dec 2016 15:00:11 +0000

Reformulation de mes questions :

La programmation a été bien passé de 1 à 6

La voiture a demarré la premiere fois et s'arrete automatique (environ 1 minute)

J'ai demarré 2e fois et reussi mais il ne s'arrete jamais (J'ai debranché avec port data link pour l'arreter). et jai remarqué que la DEL jaune reste allumé. Le module ne se programme plus (s'arrete au 3e etape : LED bleu s'éteind quand je branche les connecteurs restants) : conflits avec fil jaune A1 et D3 (ils sont relié directe par T-HARNAIS)

Mes 3 questions : 1) Est qu'il y avait un mauvais branchement ou juste des fils mal connectés ?

ou Est ce qu'il est possible evo all demarre qd meme la voiture avec mauvaise branchement ? ou demarrage reussi = bon branchement

Remarque : quelqes ports sont lousses (pas tres bien serré), je vais les ressouder . Ils sont solides maintenant

2) Pouvez-vous me dire quel ports ou pins supportent plus de courant pendant le processus de demarrage ? Cela m'aide a les bien fixer ou ajouter fusible

3) Dans le logiciel ou boot de l'unité evo all, est ce qu'il y a un système de blocage automatioque (necessitant un code special pour le debloquer) en cas de detection de certains commandes inconnues (par ex : connecteurs bougent peuvent lui generer des commandes non conformes).

DODGE grand caravan 2008

1er demarrage EVO ALL autonome reussi

Sat, 03 Dec 2016 09:27:03 +0000

Etat avec EVO ALL stand alone :

La programmation a été bien passé de 1 à 6

La voiture a demarré la premiere fois et s'arrete automatique (environ 1 minute)

J'ai demarré 2e fois et reussi mais il ne s'arrete jamais (J'ai debranché avec port data link pour l'arreter). et jai remarqué que la DEL jaune reste allumé. Le module ne se programme plus (s'arrete au 3e etape : LED bleu s'éteind quand je branche les connecteurs restants)

Mes 3 questions : 1) Est qu'il y avait un mauvais branchement ou juste des fils mal connectés ?

Remarque : quelqes ports sont lousses (pas tres bien serré), je vais les ressouder .

2) Pouvez-vous me dire quel ports ou pins supportent plus de courant pendant le processus de demarrage ?

3) Dans le logiciel ou boot de l'unité evo all, est ce qu'il y a un système de blocage automatioque (necessitant un code special pour le debloquer) en cas de detection de certains commandes inconnues (par ex : connecteurs bougent peuvent lui generer des commandes non conformes).

Demarrage autonome avec EVO CHRT4

Wed, 30 Nov 2016 16:15:44 +0000

J'ai acheté la semaine derniere EVO all avec CHRT4 ( Hardware Vr 6 et Firmware 4.18 ).

Je l'ai installé moi même et j'ai choisi STAND ALONE comme essayage :

Programmation : tout est correct avec telecommande d'origine ( LED bleu s'eteint).

Mais, la voiture DODGE caravan 2008 ne demarre pas avec mon lock x3. Le module reconnait bien ma clé (LED bleu clignote chaque commande : lock ou unlock) . et LED jaune allumé que la voiture est demmarée (a la main).

Est ce juste un probleme de version du logiciel ? Peux-je changer la version en 4.25 ?

Merci

Evo-CHRT4 vs Evo-All vs Evo-One

Sun, 27 Nov 2016 17:05:28 +0000

Once installed what is the difference between the Chrt4, ALL, or ONE - besides thE CHRT4 has a T harness?

I have a 2012 Ram 2500 Diesel Automatic with the remote start module installed already so I just need the module and harness minimum. I will program it to have glow plug/heater delay and crimestopper REVO enabled with the flasher2. Is there a fee for the crimestopper enableing?

I'd like to add a crimestopper 2way system if my range is bad, but hoping the oem fob will work. There is no way to tell with my cement walls vs the window or not until it's installed. If I have to do 2way I was hoping that it would be able to do both - Have a 2 way at home and carry my oem fob in my pocket for starts when walking out to the truck, or from my office close by. I have a Ram fob Saab fob and don't have room in my pocket for a third fob.

I see the CHRT4 and ALL uses the oem keyfob which I like, can it do 2 way also at the same time as the 3x lock oem fob?

I don't understand stand alone starter vs not - I'm assuming that means the CHRT4 can be used with a 2 way? however... Under optional technology section: The One shows it can have RF (2way) remotes but says it can't do stand alone

What modules can be hooked up to the Evo-One

What external triggers can be hooked up to the CHRT4, can modules be hooked up to the CHRT4 or ALL?

In the bottom check mark section the CHRT4 has NA for remote start so does that mean it can't do 2way, this contradicts the Stand Alone option above?

I see no difference between the CHRT4 and the ALL if I get the THAR-CHR4 T harness. In fact based on contradictory information on the compare screen I see no difference at all between all three models, except price since my truck has the remote start function setup but just needs the module/controller. They all say the will monitor for 3x lock and will start or stop the vehicle. Can you please ellaborate on the differences in detail, including options, modules, triggers, systems, etc that can be added. I'd like to see the whole picture and know which is more future proof/upgradeable as well.

Thanks for your time,

James

				The module will monitor the OEM remote for 3X Lock and will start or stop

Does the evo crt4 turn on heated seats

Sun, 20 Nov 2016 22:09:27 +0000

2010 dodge 2500 diesel

My grand caravan 2015 sensor Gate on and all the lights on after the installation of evo-all

Wed, 02 Nov 2016 20:36:27 +0000

After the installation of the Evo-All CHRT4, my Dodge Caravan 2015 have the GATE indicator on on the dashboard and all the internal lights on too. What can I do?

Having being remote started stops responding to remote unless really near by the car

Sun, 14 Feb 2016 13:50:37 +0000

I got EVO-CHRT4 (with the flashlink, so updated everything to up-to-date at that point) for Chrysler Town & Country 2013 in early Dec 2015, and installed it somewhere mid December 2015. I don't have FW versions from top of my head, and the unit is mounted in the car and it is cold outside ATM (NH).

Originally everything worked out splendidly. But since probably a month ago (I haven't done anything to the car since then, may be washed it once or twice ;) ) I have started to observe that having started the car remotely, the car stops responding to the fob/remote -- I can't unlock the car, or open side doors, anything, UNLESS I come really close to the car, like to the driver's door. I have tried with the 2nd fob/remote -- the same story -- no reaction. What could be the reason? I did recently change battery in one of the remotes. Car does pick up my presses originaly from about 60-100m.

I purchased an EVO-CHRT4 for my 2010 Dodge Grand Caravan will I need a bypass for the Sentry Key Imobilizer?

Tue, 29 Dec 2015 18:38:21 +0000

Before tearing into my Dash I've been cautiously reading about the connectors and bypasses and everything and not sure I have evertying I need. I've got the harness fixed with the proper wires cut and spliced. (yellow from the 20-pin to the yellow coming out of the harness and yello/green from the red connector to yellow between the T) so I think I'm ready. But now I'm reading about the Sentry Key Imobilizer that will shut off the engine if the key isn't detected and see in the owner's manual that it states "The Sentry Key Immobilizer system is not compatible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection." Will this product bypass that Sentry Key Immobilizer system and allow the remote start to work?

CHRT4 installation with Parking Lights

Mon, 23 Nov 2015 16:51:22 +0000

In the installation instruction it notes:

If a parking lights (+) wire is use : they require more than

10Amp. Connect the remote-starter’s power directly to the

vehicles battery with the appropriate fuse.

Does this apply to connecting the (-) Parking Lights from plug A, on a Stand Alone installation?

Why does the Starter Solenoid chatter when only using the REVO-1 RF kit?

Sat, 07 Feb 2015 15:18:57 +0000

I have a 2010 Dodge Ram 1500 with the Evo all and the T harness. Along with the standalone 3x factory remote start, i added the REVO-1 RF Kit. Everthing works perfectly fine until the outside temperature drops down to probably 20 to 30 degrees F and colder. If the truck has set for a while, using the Revo, the solenoid will chatter for several seconds before it will eventually start. Now if the truck was just running and shut off or recently running. The second start attempt using the Revo, the truck will start no problem and continue to until it sets awhile in the cold.

Using the factory 3x remote, no issues no matter the temperature. The REVO also will work just fine when temperatures start to rise.

parking lights start flashing randomly while driving the vehicle using a EVO-CHRT4 and a lcpro-4 starter

Fri, 23 Jan 2015 19:41:50 +0000

While driving down the road the flashers will start blinking on and off then it will go away for a couple of minutes then it will start again and so on.

evo-chrt4 dodge charger 2008 red light only

Thu, 22 Jan 2015 13:07:13 +0000

when i connect the device to the using the T-harness then i insert the 4 pin data link while holding the button it is only giving a red light.

second then which connection type should i use for my car

2008 Grand Cherokee Evo-All Stand alone will program but wont start

Mon, 12 Jan 2015 12:10:35 +0000

I installed the chrt4 stand alone unit on a 2008 grand Cherokee. It will program but will not start the vehicle. I tested to see if the yellow/blue wire had constant voltage(12V) and if the yellow/blue wire had voltage(12V) when attempting to start and it did. Im just at a loss for why it wont start. Any help would be appreciated. I bought this from the fortin website and supposedly it is updated with the latest software.

thank you

starts then shuts off

Tue, 06 Jan 2015 21:04:50 +0000

i have a 2010 dodge ram 1500, 3X lock starts it up and then it shuts off after a few seconds. read other posts and messed around with some options but still shuts down after start. i used the chrt4 harness with the evo all..

2010 Dodge Journey 3.5. LCPRO-4 EVO-CHRT4

Fri, 02 Jan 2015 08:54:25 +0000

Final step of programming the module and the Blue LED doesn't flash?

2010 challenger starter cut in/out during cranking

Tue, 23 Dec 2014 01:25:45 +0000

Installed prostart ct3471-tw in 2010 dodge charger, auto, key start, with EVO-CHRT4, power and ground both units through d2d/t-harness. Ground with 1.67k resistor for parking lamps. Using Fortin protocol on bypass and remote start. door locks and trunk release work well. programmed bypass and prostart as usual, tach through bypass. tach programmed good. Modify T- harness as per diagram A- cut yellow wire in T between connectors, connect D1 ylw grn to cut yellow wire,Vehicle remote starts normally most of time, occasionally when cranking with remote starter it will crank longer before actually starting and while cranking starter is cutting in and out, making awful noise.seems worse the longer it sits between remote starts, cannot dupicate with key starting vehicle. Tried reprogramming tach, with no noticeable change. Would using power and ground for remote start from d2d wires as per wiring diagram A on THAR-CHR4 instructions be insufficient. Do I need to hardwire tach signal. Any ideas.

Evo-Chr T1 can i use it for 14' Caravan??

Mon, 22 Dec 2014 15:37:41 +0000

I have a old Evo-Chr T1 still in stock and ran out of harness 4's. Is it possible to use this set up in a 14' Caravan? If so, which firmware should it be updated too?

installed evo chrt4 on 2011 chyrsler town and country will not start says stand alone on box

Sun, 21 Dec 2014 22:55:52 +0000

Lights flash each time I press lock but no start

No Start Problem

Sat, 20 Dec 2014 19:07:45 +0000

I have a 2010 Dodge Challenger Automatic and purchased the EvoCHRT4 remote start kit. The unit programs correctly but it won't start the car. The ignition lights up and when I hit Lock x 3 but not start. I then tried to start the car manually and it won't start manually either. I unplugged the T-harness and plugged the oem harness in just to check and it works. So something must be going on with my wiring?

I cut the yellow wire from the female T-harness and connected the yellow/green and yellow 12volt to the other end of the cut wire. I also enabled Remote Start in both bypass and remote options. Could you tell me what I'm doing wrong?

w2w help with evo-all and chr4 t-harness (flashlink manager options)

Sat, 06 Dec 2014 18:44:45 +0000

I have a 2009 dodge charger that i wish to install an aftermarket remote starter, i have the chr4 tharness (altered for my year/make/model) my evo-all is programmed via flashlink, and i wish to go for a hardwired (w2w) connection. I'm mechanically and electronically inclined, just confused as to options in the flashlink manager. If i enable option B2 (B2 Extended unit

follow up to response

Mon, 28 Apr 2014 14:31:10 +0000

Thanks so much for your reply.

Service # is 001A06 145015

I grounded the dark blue wire temporarily, I'm awaiting for a tilt swithch for the hood to be sent to me which I ordered online.

Was grounding that wire my mistake?

Red Light result after programming

Sat, 26 Apr 2014 18:06:07 +0000

2012 Dodge Durango CHRT4 Connection C (stand alone). Have everything wired up but keep getting Red Light as result on the last step #8 (Press the lock button on OEM). Everything else up to that step. Ignition Yellow wire from 20 pin is matched up to Yello wire from T Harness. Not using Extenral Input or Parking light out as indicated.

Thanks for your help!

Why does all my Lights (headlamp,taillamp,parking lamp, and fog lamps) come on with remote start?

Sat, 01 Mar 2014 19:58:56 +0000

2013 Dodge Grand Caravan SXT

OK I did the install on a 2013 Dodge Grand Caravan and every thing seemed OK, I do have one question, when remote starting all lights come on Headlamps, tail lamps, parking lamps, license plate lamp and the fog lamps, (if the fog lamps were turn on before.) (this is with the switch completely off)

This happened even before I tapped in the Green/White parking lamp circuit. Everything else works fine, hood switch and brake pedal turns off the remote start.

After putting in the key and turning to the run position, the lights stay on till I push the brake pedal to put it in gear and then the lights shut off.

disconnecting the parking lamp circuit does not change anything. On remote start all the light still come on.

I used a EVO-CHRT4 # 001A06 319593 Version 74.14

evo-chrt4 error in manual, or wrong harness with unit?

Mon, 10 Feb 2014 15:02:21 +0000

I am working on a 2008 charger, chose to use the evo-chrt4 for stand-alone installation. In the manual that came with the evo-chrt4 it says "for vehicles 2010 and less cut the vehicles ignition" which is fine. but in the manual it shows a picture of the "YELLOW" wire being in the t-harness.. my t-harness does not have a yellow wire. i called and all the guy could tell me was that i had the wrong harness cause only the t2 harness is supposed to have the YELLOW wire.. i just checked the vehicle, it does not have a yellow wire..

So. according to the instructions i am supposed to cut a non-existant yellow wire in the T-Harness?!?!? I have looked over the site fairly well, and have seen in all the instuctions pertaining to the t-harness that there is supose to be a yellow wire. i have also found that this wire being cut is needed to allow you to shift the the car from park.

I have verified the part number listed on the t-harness is "evo-chrt4" the installation guide that came with the unit is revision 20130215(which appears to be the newest revision). and the service number on the evo all that i am using is 001a06 238084 (not that the service # matters as i feel that the error is in the manual, and not something to do with the unit.. also i could not find a service number on the t-harness, is there one?

thank you for you time.