Questions & Answers - Questions récentes tagguées flashing

Blue light keeps flashing step 6

Thu, 29 Jan 2026 21:45:19 +0000

Step 6, turning off the ignition but the blue light keeps flashing. Doesn't turn off or switch to red and yellow alternating. Rav4 2025 hybrid push to start.

evo one programming 2010 mercury red light don't flash 10 times

Tue, 14 Jan 2025 04:22:15 +0000

i installed evo one as instructed by guide 22301 and all wires confirmed to be as on the manual, during programming the key the light dont flash 10 times

I uploaded newer version and the recommended version by flashlink and didn't work .

additional question, can i start it through oem remote 3X lock or not .

thanks

Fortin EVO-ALL 2015 Nissan Rogue - Locking/Unlocking While Driving

Mon, 22 Jan 2024 13:07:08 +0000

Just installed an EVO All with the Nis3 Harness last night. While driving the car the unit unlocks and locks while flashing the turn signals every few seconds.

I am curious as to what this could be. I've updated all firmware and enabled all unit options that were in the install manual.

What could this be?

reaching flashing limits

Mon, 11 Dec 2023 10:57:54 +0000

sorry for annoying you i have three modules reached their limit in flashing

can you reset it for me please

SN:

001A07391471

001A07471062

001A07356060

thank you very much.

Red light flashing at the end of programming

Sun, 10 Sep 2023 17:33:33 +0000

After a few tries and using the forum here, I couldn't get the yellow and red light to come on at the end of programming my diesel sq5 2013.

I tried a number of things, including different versions and resets. Always ends up with the red led blinking rather than the yellow and red.

Can someone tell me what firmware version I should be on?

The wizard goes to 60.8, but the manual says it needs to be 60.10 or higher. So I tried both for the q5 and sq5 versions.

Can someone reset my flash limit?

I used 7 out 8 at this point. Looks like I'll need more by the looks of it.

My car is giving me power steering warning errors? Any ideas why that is happening?

SN: 001A07 470303 (module for reset). Assuming that is the serial number required.

NO FLASHING BLUE LIGHT AT STAGE 5

Thu, 19 Jan 2023 20:45:29 +0000

2014 VOLKSWAGON JETTA TDI AUTOMATIC TRANS
AFTER REPROGRAMMING EVO ONE 3 TIMES STILL CANT GET THE EVO ONE BLUE LIGHT TO FLASH AFTER TURNING ON IGNITION, BLUE STAYS LIT THEN WHEN IGNITION IS ON LIGHT GOES OUT UNTILL YOU TURN IGNITION BACK OFF THEN BLUE LIGHT COMES BACK ON?

FORTIN EVO-ONE W/
VWT1 T HARNESS
DATE 12/2021
s/n 002b04 248922
firmware remote start = 1.[26] hardware 7.0
BYPASS = 75.[41]
hardware 4.0
loaded suggested options on both with diesel option checked

'18 Malibu Flashing Headlights & DRLs

Fri, 13 Jan 2023 16:28:18 +0000

Hello, I have an '18 Malibu smart key and I have installed the EVO-ALL module and programmed. While the car is starting via the module, it seems it is glitchy. The dash turns on and off, displaying different messages, and the headlights and daytime running lights will turn on and off as well. This ends with the headlights off, DRLs on, and brake lights on. My question is if this is normal? And if so, I would suggest an update to the module. One time I remote started the car and after a second, the dash displayed No Remote Detected, then everything turned off and then the car started after a few more seconds. I noticed the harness has a couple loose wires and a couple other connectors attached. Do these need to be connected to anything?

How do I turn of A12

Wed, 02 Feb 2022 10:36:04 +0000

I asked a question regarding vehicle not starting and red LED flashing five times on a 2009 Toyota Venza. The response I received was to turn off A11. However I am not a programming location and do not know how to turn off A11. Do I need to send the unit back again to have it turned off?

Security light keeps flashing while driving even after key take over

Sat, 18 Dec 2021 00:24:47 +0000

I have the RFK 912, my wiring is correct but when i go to do key take over with the key turned to the run postion and press on the break the attena acknowleges and gives me a solid green light but shortly after it starts to flash again. Even restarting the car doesnt seem to work, the only time it doestn flash is when the car is off and i go to unlock it with my RFK Fob

I have the evo one for reference

SN: 002B04220286

How do i know if the evo all for my jeep patriot 2013 is active after glasing

Thu, 16 Dec 2021 19:01:25 +0000

How to find out if flash was done right

How to add a blue flashing light for when system is armed?

Thu, 11 Feb 2021 15:01:43 +0000

I want to add a flashing blue light to warn off vehicle burglar. I tried you white wire on evo all, but it's a staying a ground with car running or off.

Rfk-912 antenna

Sat, 10 Oct 2020 18:00:51 +0000

Is there any update came out to stop antenna power saving mode and to keep it constantly flashing ?

Module appears to pass dcryptor, but still slow flashes blue when installed.

Sat, 22 Feb 2020 19:25:13 +0000

After returning module to truck after Dcryptor processs completes, the module still slow flashes blue when installed. The truck still starts with the key, remotely locks and unlocks, but will not remote start. The module does nothing but slow flash blue. I don't see anything in the instructions or troubleshooting about this problem.

2016 Hyundai accent standard key Blue programming light turns off when I turn the ignition on

Tue, 07 May 2019 13:11:38 +0000

When installing the Evo one on my 2016 Hyundai Accent the blue programming light turns off when I turn the car on and the light comes back on when I turn it off have the can wires on the right ones do I need the can wires to use the remote start?What options do I need to change the service number is 002B07144688

2017 Ram Flashing headlights on and off when tip start key turned to on.

Tue, 07 May 2019 13:06:54 +0000

Fortin remote start installed and working in my 2017 Ram 5.7l with Tip start key. Headlights flash on and off three times after OEM remote key inserted and turned to on position. Is there a setting to stop the headlights flashing on and off at people. I have the extended range remotes also installed and working.

Evo all not flashing blue on step 10

Mon, 14 Jan 2019 16:40:48 +0000

When going through the installation process the Evo all does not flash blue on step 10. All wires are connected with the exception of the hood wire. I have tried firmware 74.32 like the guide suggests as well as 74.18 like the flashlinj suggests.

How do I install EVO-ALL FORT3 on 2018 Mustang?

Sun, 06 Jan 2019 21:31:51 +0000

Hello, I am really having some trouble with this product.

So I ordered the preprogrammed plug and play Evo-Fort3 with T-Harness, with the StandAlone I believe.

I have updated the programmer with the flashlink system but my main question is, can I just simply install it into the car once updated with JUST the T-Harness and connected wires? Or do I actually have to cut and sauter all the other wires included in the package? Including the hood pin and switch?

I was under the impression off your website when looking into this that I could just install it immediately with what was given instead of having to turn into a car genius and cutting all these wires.

Please help me out here man. Thanks.

I have installed it multiple times through the back of the OBD11 port just as the unit comes as a whole and got through some programming until I go to try the remote start, then it flashes red then both red and orange and clicks but car does not start.

starter will not flash says reached its limit

Wed, 26 Dec 2018 09:41:06 +0000

my starter was acting up. tried to reset and update. I tried several times and eventually it said can no longer flash. I have a deisel ram 2500 2015 model. I remember when we set it up the first time there were alot of steps to get it right do to the truck. I have tried to reach out since the day before christmas and have not recieved any response.Please help rest it and assist with new progam.

thank you

xtra wires? no red led when programming

Mon, 26 Nov 2018 11:46:50 +0000

2005 chevy silverado 1500

using install guide 61101 evo one.

during programming blue led goes off but no red led, I have verified obdII connection. firmware is 70.21

another question is should i wire in the unlock, lock, +ign, -ign, -disarm on the 20pin?

Mazda 6 and no more flashing

Tue, 30 Oct 2018 03:59:54 +0000

I have problem with mazda6 2017 push-to--start automatic evo-one with thar-maz1. its worked but gives errorcodes and cruise disabled when i takeover and drive, i tried different firmwares and now its locked - can't flash anymore. what options I have? It can work as well as before because now I have nothing

2008 Honda CRV, blue light flashing slowly after programming

Tue, 23 Oct 2018 02:03:29 +0000

Following guide #57701 I have installed an EVO-ONE service no:002b07 184652 into a 2008 Honda CRV.

Programming steps 1-5 appear to go fine, at step 6 when i turn off the ignition the blue light starts flashing slowly and does not turn off.

I've verified wire connections and unplugged the module and attempted to start. The security light flashes and will not start.

Any idea what I have done wrong?

No blinking blue light when programming in step 4 of install guide for a 2018 Mazda CX9.

Sun, 21 Oct 2018 17:19:51 +0000

I bought the EVO-One and the THAR-ONE-MAZ3 T-harness for a 2018 Mazda CX9. I got the t harness installed fairly easy but am having trouble programming. I hold the programming button while I connect the 6 pin main connector, release when the blue light is solid, connect the rest of harness, press on 2x but the LEDs never flash as instructed. I'm not sure how to proceed from here, I've reset the module and tried a few times. The 20 pin connector has a bunch of lose wires on the t-harness, should this be connected to anything? From my understamding only the optional parking light wires needed hardwiring, everything else was plug and play.

No flashing blue light during programming.

Fri, 08 Dec 2017 20:33:28 +0000

I have a 2013 Kia forte. I Installed the evo one using thar-one-khy1 t-harness. I have programmed both the remote start and bypass sides of unit but i do not get a flashing blue light during programming through can bus. When I turn key to on the blue light goes out and doesn't flash. I have verified that i have the can wires correct. They both show 2.3v. Vehicle does not have pats data wire or immobilizer

2013 Mazda CX-5 programming issue

Mon, 16 Jan 2017 10:20:22 +0000

Difficulty programming unit. First had issues getting the module to learn the keys but realized I had low voltage. Charged battery and went through all steps up to 25 (towards end of CAN programming). At the end of sequence I received the blue light and it went off, then waited about a minute or longer, but never received the red LED. I've been through all steps including 1-12 and starting at 17, 18 and 21 but without success, have reset and resent data, but usually only receive flashing red. How can I completely start over as the unit seems not to fully reset after master reset and only get flashing red after going through 1-12 again. What process where should I start? Thanks.