Questions & Answers - Questions récentes tagguées ford-f150

2014 F150 Install Assistance for Parking Light

Fri, 12 Dec 2025 23:14:42 +0000

I have a FOR1 T-harness and EVO-ALL and I'm trying to wire it up for the first time. I'm using page 6 of this document as my guide. https://www.wirecolor.com/download/94891/94891.pdf

I've tapped into BCM Passenger Kick Panel for Parking Light+, but I'm not sure what to do with this wire. Am I expected to bring my own relay? Do I double up the wire on the existing factory relay and then run a wire from the factory relay to EVO-ALL? I've never tapped into a relay, do people just pop it out and put wire alongside the pin as the put it back in or is there a way to use a posi-tap on the back side easily?

2020 f150 lock/unlock/lock option known issue?

Fri, 14 Nov 2025 17:26:15 +0000

Has anyone experienced this issue with the 2020+ f150 stand alone with t harness lock unlock lock?

The install is like 5 minutes and goes great. Test at the door l/u/l fires right up. The problem is as soon as you move away a few feet from door with key ....the vehicle lets you lock unlock the park lights come on and you cannot lock again until lights time out which isn't fast enough for remote start sequence. 3x lock works fine but you have the horn honk as usual. Has this happened to anyone else? Just wondering

2014 Ford F-150 XL Stand Alone Install No Power Windows/Power Locks

Thu, 25 Sep 2025 19:16:23 +0000

Hi Fortin,

I recently purchased a F-150 that was a bare bones truck meaning no power windows and no power locks. If I get the 2 Ford keys with buttons on key for lock and unlock, will it work with a evo-all and tharness 3x lock installation?

Not sure if this vehicle will still have canbus lock signals available to program the remote start or will the keyless entry buttons also work. Does the vehicle still have unlock and lock features the car came with only a regular key no buttons?

Or will i have to do the install and add a fortin RF kit?

Programming doesn't complete, new EVO-ALL on F150/2012, firmware flashed

Sat, 19 Jul 2025 03:52:12 +0000

Can't find anything in the questions/answers that is exactly like this issue but I can't seem to complete the programming on my truck.. I've double and tripple checked the wiring, can-high/low, key sense A1,A10,A20 were connected as well.
First time it seemed to sense the keys, waited the 3 seconds each and returned to the 1st factory key.. waited for 3 or 4 minutes and no status change so I tried it again. Seemed to go a little further and the system locked/unlocked the doors and the stopped again.. no 10x flash of the indicator either. reflashed the unit and tried again, this time nothing seems to progress. I can put the unit into programming mode (blue/red solid) When I touch a key to the ignition I see a quick flash of the yellow, turn to run and wait 3, 2nd key doesn't show anything.. return to the first key and nothing happens. lights won't change at all and just stuck at solid blue/red. I've tried tapping the button when the key is inserted, but that does nothing either. One really strange issue is I started the truck after (unit was still connected) and it would not shut off until I pulled the connectors off the controller.. brake pedal didn't do anything, opening the door didn't light the interior or turn on the parking lights.

Any ideas? THAR-FORD1 with EVO-ALL

New EVO-ALL won't pass step one for programming

Sun, 13 Jul 2025 19:43:20 +0000

Brand new unit EVO-ALL won't pass step 1 for programming. All three lights flash in sync (not alternating) Do these units ship without any firmware?

2015 Ford F150 won’t go into step #4

Sat, 14 Jun 2025 14:43:26 +0000

2015 Ford 150 with keyless entry and factory hood pin.

During the programming steps, it will not flash after ignition is in RUN position. Blue light remains Solid.

I’ve verified all my connections and are good.

EvoAll s/n: 001A07649192

Firmware: 4.01

2016 F-150 evo all can not program new key

Wed, 26 Feb 2025 13:04:00 +0000

I have 2016 F-150 my remote starter is Evo-all programed with Autostar fob. I got new Auto star fob or remote and I tried many ways to program it but it did not work at all. When I connect to Flashlink to my computer it does mention there is 1 key only. Please I need help ?

2018 Ford f150, why no blue flashing light after programming

Mon, 05 Feb 2024 07:37:25 +0000

2018 Ford f150 standard key without keyless entry, evo-on, T-harness FORT2, firmware 4.01, not getting the blue flashing light or red yellow alternating at step 8 of bypass programming procedure, getting the red flashing light 1 flash per second after the last step where ignition turns on and off by itself.

f150 2016 just start once

Tue, 22 Aug 2023 15:52:57 +0000

hello i installed a evo all for3 for f150 2015. the firmware 4.01 i done the program and everything good but the car just start once when i start it again the car doesnt start just the car alarm start once.

i checked the hood every thing good the car came with hood pin.

the SN: 001A07 390594

this my customer car i need help please

Evo-One 2018 Ford F150 Programming Issue, Blue LED does not turn OFF on unit

Fri, 28 Jul 2023 14:01:33 +0000

2018 F-150 STD-key w/o keyless. After pressing the program button 8 times red and blue LEDs are solid. Putting key near ignition does nothing, inserting the key, then removing it, the ignition turns on, then red LED blinks and ready for next step. I cant seem to get the blue light to come off during step 6 without inserting the key, not sure why. I've tried multiple firmwares but they all do the same. I've also verified my wiring.

2014 Ford F-150, 2 Keys programming.

Thu, 02 Feb 2023 08:47:50 +0000

Hi there. I have one question about Ford OEM keys.I am trying to program a compustar module on a Ford F-150. I only have one OEM key and the other one is made by a locksmith (it's not a clone and it's not a copy) But I can't finish the programming because the module tells me that I am using the same key or a cloned key. My question is: does Ford split any code between two keys? If you don't have both OEM, is it not possible to finish the programming even if the key made by the locksmith is not a copy or a clone? I need some information about this. Thank you very much in advance. Kind regards.

Will the Fortin Module remote start 3x lock on a 2019 Ford F-150 STD Key with Keyless if the check engine is on?

Sat, 19 Nov 2022 10:33:37 +0000

Will the Fortin Module remote start 3x lock on a 2019 Ford F-150 STD Key with Keyless if the check engine is on?

EVO-ONE 2017 F-150 Won’t start

Fri, 21 Oct 2022 17:45:29 +0000

Hi I installed the Evo-One on my 2017 F150 program good sends signal but don't start

SN: 002B04 224734

F150 2012 programming

Wed, 17 Aug 2022 21:05:44 +0000

I have a f150 2012 i done every thing 100% In the programing phase I made every thing i enter the first key after the second key and after the first key then the blue and red started flashing after that only the blue led appeared and the still on without the key but if i unplugged the red connector the car turn off please can you help me in the programing

2006 F150 door locks inop after remote start timeout

Sun, 09 Jan 2022 22:04:47 +0000

2006 F150 5.4 FX4 with EVO ONE and RFK 441. The unit works fine however after the 15min run time out or if you shut the vehicle off with the remote the doors won't unlock with fob or the keypad on drivers door, lock still functions. If you open and close the door then it begins to work again

The only way to remedy this is to use the key to open the door or to remote start the truck and unlock the doors. This is very much a truck issue not a remote start issue as this vehicle is all analog connections. Is there a wire that I can have pulse the door pin to shut the radio down and simulate the door opening as I believe that would fix it. There was nothing mentioned in the install guide.

2011 f150 what wires do I have to connect

Sat, 01 Jan 2022 13:46:36 +0000

To get the parking lights to come on while running.

Will not remote start

Sat, 11 Dec 2021 16:48:36 +0000

Installed evo all

I press lock 3 times blue light will flash each time then the red light flashes ignition doesn't turn on and vehicle doesn't crank 2009 f150

2019 ford f150 won't start

Mon, 22 Mar 2021 03:02:45 +0000

Hi, installed evo all with t harness stand alone and it programmed fine, but it won't start the blue light on evo all blinks blue with 1st and 2nd press but not on 3rd press. Is there a way to activate the evo all to make sure it's programmed right, is there a wire i can ground to activate it? Does option b2 need to be on to add evo all single button one way rf kit ? Does protocol have to be set to fortin or is it automatically set to fortin? SN 001A07011080

2012 ford f150 Will not remote start

Wed, 17 Feb 2021 21:41:35 +0000

Will not remote start

Evo All with Fort-4 wont program 2012 F150

Fri, 05 Feb 2021 22:23:37 +0000

I'm having a hard time getting the programming finished on a fort4 evo all on a 2012 f150. Im doing it as a standalone remote start and have 2 keys. I've used the flashlink and made sure its flashed for the truck and standalone. When i go to program initially i hold the program button then plug in the power cord and let off at the blue/red light. I then plug everything else in and start the key process with 2 master keys, it wont ever get to the flashing blue/red 10x doing it that way and the truck will stay powered on even after i remove the key. If i keep the red plug unplugged and try the programming i can get the red/blue to flash 10x but it never goes to the last step of flashing the can bus. I try to plug in the red plug after the 10x flash and it goes back to truck will stay powered on with no key in the ignition. Any ideas?

2005 f150 using evo one

Sat, 16 Jan 2021 20:51:53 +0000

Im installing a evo one kit in this truck , according to the install guides it should work with 3 press remote start . what i cant figuire out is how to activate it ? It isnt a can bus system and the install guide doesnt list what wires to connect to interface the factory wiring to the evo one , it is enabled in the firmware and all firmware is at the current level .

F150 EVO ALL Strangeness

Sun, 29 Nov 2020 23:48:47 +0000

Hello,

I am hooking up an EVO-ALL to operate my OEM remote starter via a CARLINK ASCL6. I am also attempting to add a shock sensor and blinking LED. I am using t-harness THAR-FORT4.

It took quite a bit to get the ASCL6 to talk to the EVO-ALL. I could only get it to "talk" by sending a lock command during the learning process. For some reason I did it on a whim after trying all sorts of plug combinations etc.

However, now it has no confirmation of the commands it sends. It send 3 separate pulses for the lock and unlock commands. I had to wire the Lock [(white/black) to BCM (blue/green)] and Unlock [(white) to BCM (yellow/violet)] for the lock commands to send. Why am I not getting a status reading? Do I have to wire the Driver Door Pin?

I thought this would be mostly plug and play, but it seems like there is some wiring that needs to be done.

Also, LED is wired to 12v+ and negative to white wire on the 20 pin but it is not working. I also have a shock sensor on the way and need help with that. I've been at this for 3-4 days off and on. Programmed as standalone remote start and EVO alarm via Flashlink. HELP!

Thanks

2016 Ford F150 with Fort 3 harness not starting truck after first programming

Sun, 01 Nov 2020 18:50:07 +0000

Have installed the Fort 3 t harness , Evo all has been flashed with Flashlink 4.

Firmware 4.02 A11 off and C1 selected.

Completed module installation and truck starts when pressing lock 3 times.(when reprograming module the truck always starts on first test only)

Upon an second attempt to press lock 3 times results in module goes red, orange and then blue, truck horn honks.(no start)

it tries to do this two times and then 3 red lights blink on the unit.

When opening door truck warns of alarm going off unless i insert key.

Please can you advise.

Thnak you very much

Fort2 programming issues

Sun, 11 Oct 2020 18:23:14 +0000

Trying to program my 17 f150 std key w/ keyless. I get to the point where it has me press the button 8 times. After I do that I put the key up to the ignition cylinder (not in it) and when I press the button, nothing happens. The red/blue lights stay on solid and the truck does nothing. I programmed the module with the latest firmware and other firmwares with no success. All connections have been verified.

EDIT: Found out I had a bad connection however I have a new problem. After going through the programming sequence for the second key, after the ignition shuts off, the red LED flashes. When going back to the computer I get a message saying the immobilizer data received from the module is incomplete. I have tried the entire procedure 3 times with the same result.

EDIT 2: I got it to go through all the steps. New issue now. When attempting to start the truck via the RF kit, I get a red light, then red/yellow light. They go out. Then I get red then red/yellow again. After that I get 3 red flashes and nothing else happens. The starter does not respond to 3x lock, although I can not remember if I disabled it or not.

why are the yellow and red light solid on my evo ford f150 during step 5?

Mon, 28 Sep 2020 18:11:58 +0000

I have checked the yellow ignition wire, the can high and low and the tx/rx

I have EVO all. where can I find a T harness for 2009 ford F150?

Mon, 20 Apr 2020 10:53:13 +0000

Getting ready to install EVO ALL in my 2009 F150. I cant seem to find a T harness. Any idea where I can find one?

F-150 2011 Key Programming No Blue Led Flash

Thu, 02 Jan 2020 14:54:37 +0000

Hi all. I have an EVO ALL with the Ford1 T-harness that I'm trying to install into my 2011 F-150 standard key for remote start. I have followed all the instructions and when I get to releasing on red + blue like the instructions state the programming does not go as described. The instructions say after putting key 1 back in I should get 10 blue flashes and 10 red flashes. In my case the truck locks and unlocks and then I get 10 red flashes only, blue stays on. After this, all LEDs turn off and pressing lock 3 times only makes the blue led flash and nothing else, no start. Any ideas? Thanks in advance.

evo ride cannot flash anymore?

Sat, 28 Dec 2019 20:40:27 +0000

i have command start that has been installed 2013 and now stop working. i tried to update to my flashlink updater but it says device cannot be flashed anymore. device flash limit reached. ser. no. 000903 025410.

F150 2018 setup procedure not functioning

Sun, 15 Dec 2019 12:12:50 +0000

Hello, when installing the Omevoall with supplied tharness and following the plugin procedure, the blue light does not flash after placing the vehicle on run. Procedure currently being followed:

1) when the vehicle off, plug in the black plug into the black connection while holding the button and only letting go on a full blue light.

2) plugging the white plug into the white connection.

3) placing the vehicle to run.

Blue light stays as a solid blue and does not start flashing.

firmware 71.47

thar-ford3

F-150 with Evoall and Linkr-LT won't unlock.

Tue, 10 Dec 2019 21:51:22 +0000

I have the Evoall installed in a 2015 F-150 push-to-start using the THAR-FORD3 harness and a Linkr-LT. Vehicle starts and locks from app but will not unlock or trunk (tailgate is electronic) release. I also setup Aux 1-4 and none seem to do anything. Any settings I can change to make the Aux functions work?

The real question is why won't unlock work? I can live without the trunk/aux functions but seems like a waste of money without unlock.

Thanks

Will EVO-ALL with FORT1 work in my 2014 Ford F-150 FX4?

Sat, 30 Nov 2019 15:30:30 +0000

I have the EVO-ALL with FORT1 har. I also have the flash link updater. Will this unit start my vehicle by itself? Do I need anything else? I had an evo all in my old truck and used an external remote starter and only had one key and everything worked. Do I need two keys with my 2014 f150?

F-150 2019 std key and without keyless entry- Correct Installation guide

Sat, 23 Nov 2019 08:40:09 +0000

When I use the dropdown selection tabs on top to get the correct installation guide there is multiple options with no discription of the 2019 model. I need to know which installation guide to use for a 2019 F-150 std key and without keyless entry, truck. The product that was shipped to me is the EVO-Fort3 package

2018 Ford F-150 STD key evoall not starting truck

Mon, 11 Nov 2019 18:39:35 +0000

2018 Ford F150 Std Key Fort3 isnt remote starting car

Thu, 31 Oct 2019 22:28:22 +0000

Plugged in the Tharness correctly. When connecting the moduel I held down the small button on it while connecting the black power wire, and let go of it when the light was blue. Connected the white wire on the other side of the module. turned on truck to ignition on, waited for blue light to flicker for a bit then ignition off and key out. Tried the triple press on lock and nothing happens. Turn to ignition on again and the module is showing a yellow light.

Cant get the remote start to work

Evo-all w/ ASCL6 or LinkR-LT2

Thu, 10 Oct 2019 10:14:20 +0000

Currently I have installed Viper 5704 w/ evo-all as my remote start/security system in my 2006 Ford F-150. I want to upgrade the system to be able to start from my phone. I can not go with Viper smart start simply because I have to be authorized dealer to be able to activate before I can use it. For module, installation and activation they want too much. I was thinking if I can go with ether ASCL6 or LinkR-LT2 with evo-all. How can this be done? Basically what I need this Evo-all to do when I press:

Remote start ——> wire #1 pulsed ground

Remote stop ——> wire #1 pulsed ground

Door lock ——> wire #2 pulsed ground

Door unlock ——> wire #3 pulsed ground

Also if possible to hook up (Confirmation wires) GWR wire so it will let me know if car started and another wire that could be connected to siren output for alarm trigger

Pulsed ground will activate my 5704v remote start

Is it possible to configure like that? If yes what firmware, and what wires should I use in order to accomplish that? Do I need another Evo-all or can I use one that I already have?

Cannot get Linkr LT1 and EVO ALL to link together

Sun, 28 Jul 2019 14:10:44 +0000

Hi,

I have a 2019 F150 and trying to install a Linkr LT1 and an EVO ALL module. I can get the EVO ALL to work, but cannot get the Linkr LT1 to work with it. Fortin 2 is enabled through settings. Firmware 4.01 installed. Here is what has happened so far:

If I program the Fortin module first with the key fob (blue light method), I then have to unplug the module and replug it in to pair with the app (red and blue light method). This should reset the key fob programming, correct? When I do this, I try to start from the app and I hear the app chirp, then a longer chirp (assuming that's the confirmation command that it started) but being as the module has not been programmed to start, it doesn't do as such.

So I programmed the linkr module first (since it has constant power through this process, hoping it would remember the programming), then I programmed the Fortin module, but now I don't get that confirmation chirp, although it works through my key fob.

Any settings I am missing? I cannot get the app to work for the life of me.

2016 F150 XLT Std Key EVO-ALL w/ Fort3 Standalone Mode C1 & D1 Options Good--No Start

Sun, 07 Jul 2019 21:32:28 +0000

I am in the process of installing an EVO-ALL device with a Fort3 cable into a 2016 F150 XLT with standard key.

The module programmed correctly.
The hood is definitely closed.
When attempting to remote start using a LOCK, UNLOCK, LOCK sequence the BLUE LED flashes once with each LOCK button press and twice with the UNLOCK button press.
After the third (LOCK) button press the LEDs go through a flashing sequence that ends with a pause (no LEDs lit) followed by three quick flashes of the RED LED which I understand means NO TACH.

I verified that options C1 and D1 have been turned ON by doing the following:

I grounded the A8 pin of the 20 pin connector. The RED LED did NOT light so option D1 should be on.
I momentarily grounded the A13 pin of the 20 pin connector. The LEDs went through a flashing sequence very similar if not identical to the one that they go through when attempting a LOCK, UNLOCK, LOCK type remote start. The flashing sequence ended with the same pause (no LEDs lit) followed by three flashes of the RED LED which I understand means NO TACH.

Any ideas?

Thanks!

Will the Evo-One work (stand alone remote start) using factory remotes (Lockx3) on the 2003 Ford F150?

Sat, 30 Mar 2019 20:18:55 +0000

Does the evo one require a rf kit for the 03 f150

Evo-Fort2 2018 Ford F-150 STX ignition power, no start

Tue, 26 Mar 2019 18:40:12 +0000

Programming successful except for final step. Vehicle power comes on but vehicle does not try to start. I see on the diagram there is a "rs6 in/out ignition +" coming from the yellow A1, I dont know where that wire goes besides to the T-harness. My vehicle seems to be activated by the Evo module, and won't allow key start once that occurs, and won't disable by pressing the brake. Any idea what I'm doing wrong? I did the can high and low taps at the odb, I have a factory hood switch, all light in the programming match instructions, until the point where it's supposed to turn on and then turn back off. Help!!

EVO One 2010 F150 remote start not starting

Thu, 14 Mar 2019 21:47:48 +0000

I have a 2010 F150 automatic transmission, and a EVO one. I cannot get the car to remote start. When prorgamming with 2 keys the car does not start on step 8, is this normal? I have also tryed one key and decrypting it, the data link program says it is successful.

On three press of the OEM Remote lock button I see the blue light flash and hear the EVO ONE clicking but nothing else happens. At one point I had it where the red light was coming on but no more.

Also, i did not wire for door pin, must I make that connection?

Thanks for your help

Mike

2007 f150 unable to program evo one - 2 key program

Sat, 09 Feb 2019 12:28:38 +0000

Using evo one on a 2007 ford f150.

Put device into programming mode (solid red led)

3 seconds on both keys.

Press the program button and the red led goes off and comes back solid (if i hold it for longer, it comes back flashing red) ,

not sure which is the proper status, but i've tried both.

3x lock on the oem remote and the truck does not start. No change on the evo one. (programmed evo one to accept 3x start)

I've wired up via guide 84131, no wires into CAN (it didn't say to). A2,A3,A7,A10,A11, A15(just left undone), A20, E1-6.

during programing key from step 4 of key setup both red and yellow stay on all time

Sun, 20 Jan 2019 13:57:07 +0000

peace and blessing of almighty onebe on you,. alreay check my yellow wire which is connect to 12v with key on and 0v with key off aswell rx and tx wire also attached properleya on crosponded wire can you let me know what is going on

Bypass Programming for 2010 Ford F150 not working.

Thu, 03 Jan 2019 17:02:39 +0000

I purchased an EVO-ALL kit with a crimestopper unit from MPC, and I have confirmed all wiring connections with a multimeter. I am able to remote start the vehicle when I hold a key up to the truck immobilizer ring in the ignition, but I am not able to perform the bypass programming successfully. I have two factory keys, one is a 40-bit S-type, the other is an 80-bit SA-type. The instructions I recieved from MPC do not call for the D connector on the EVO-ALL to be wired, however the standard installation instructions on Fortin's website for a 2009-2010 Ford F150 call for using the D connector when doing 2-key programming. Should I wire this connector in order for the bypass programming to be successfull?

stuck programming evo-all on 2018 F150

Thu, 03 Jan 2019 15:06:16 +0000

While programming a evo-all for standalone remote start on 2018 Ford F150 after programming key 1 and key 2 and removing both the evo-all yellow and red lights go solid and then the ignition turns on. The ignition then stays on as well as the yellow and red lights. The blue light never flashes like it is supposed to.

red pin and 5 white pin plug wire diagram and where does keysense wire go

Mon, 31 Dec 2018 18:28:58 +0000

I need a wiring diagra for the Red 6 pin plug and the. And I need a wiring diagram for the white 5 pin plug I dont konw which 1 is the RX and TX IGNITION and ground and i dont know which wire is keysense.

F150 pairing Blue light doesn't flash when sequence is followed

Sat, 29 Dec 2018 19:10:56 +0000

Hello, i recently bought a OMEVOALL version 6 firmware 71.34 OMEVOFORT preloaded with a THAR-Ford3 T plug for my 2018 f150. Following your instruction guide and this online video https://www.youtube.com/watch?v=3bpmiYwslSo , i am unable to get the blue light to flash after turning the key to the on position like in your guide and the video. My truck is equipped with a stock hood pin sensor. Any assistance would be appreciated.

2018 Ford F150 STD Key with Keyless not working

Mon, 17 Dec 2018 11:41:48 +0000

Hey Guys,

I'm trying to install an EVO-FORT3 on my 2018 Ford F150. When I wire it up using the T harness the key programs as it should but when I try to start it with the OEM fob using the three lock method nothing happens. The box sees my lock and unlock commands because I see the blue light flash, but it just doesn't start. When I ground the manual remote start trigger (yellow/black wire) from the EVO-ALL the truck starts as it should.

I don't have a cable to check the programming as it was programmed by a dealer. Does this sound like a programming issue? The truck starts when manually triggered, just not with the remote as it should.

How to program 2010 F150 with Key Decryptor

Sat, 27 Oct 2018 09:03:07 +0000

I'm using the key decryptor method to program evo-all CAN BUS module on a 2010 F150. Following the directions, I hold prog button, plug in data, release on solid red, then continue to plug in remaining connectors.

Once connected, I press prog once, the red LED turns off then on. Here's where it doesn't work correctly..

When I put key in ignition, and turn to run/on, the yellow LED turns on but the red does not turn off as stated in directions.

I do have the rx and tx wired as described in guide light blue/blk to violet/gray(rx) and light blue to orange/yellow(tx)

Firm: 71.47

Will Evo-For.T1 work on 2009 F150?

Fri, 28 Sep 2018 10:48:08 +0000

Will the Evo-For.T1 work on a 2009 F150? The Evo All installation guide shows a t-harness available but it doesn't show an installation guide. If this unit will work, which installation guide do I use?

2018 F150 EVO-FORT2 Programming issues

Sat, 08 Sep 2018 07:29:29 +0000

2018 F-150 STD-key w/ keyless. After inserting the second key, then removing it, the ignition turns on, then nothing else happens. The lights are solid red and yello. I've tried multiple firmwares but they all do the same. I've also verified my wiring.

I'm not sure if this matters but the module is an OMEVOALL. Omega branded.