Questions & Answers - Questions récentes tagguées linkr

Linkr-lt2 and Fortin rf kit?

Mon, 25 Mar 2024 12:47:27 +0000

Has this combo ever been fixed to work again?

Or is capitalism still keeping the fix from ever happening?

Evo One w/ Linkr LT2 - Transfer to New Car

Sun, 17 Sep 2023 13:22:12 +0000

The time has come to let the 2015 Honda Odyssey go, .

I have the Evo One with Linkr LT2 for several years now and works flawlessly. As a matter of fact, I have the same set-up in 2 of my other vehicles. GREAT PRODUCT!

Question, do I have to do a complete "hard" reset prior to installing the Evo One or can I use the flashlink to make the changes (new vehicle, key, etc) and update the Evo One. And would you know if I have to "reset" the Linkr LT2?

Any suggestions would greatly be appreciated.

FYI, I'm going from a 2015 Odyssey to a 2019 CX5 (I have the THAR-ONE-MAZ3 already on order).

Linkr lt2 + Evo All

Tue, 19 Jul 2022 03:35:12 +0000

What settings should I change in my Fortin Evo all for my LT2 to work accordingly, so far the lock and unlock, GPS location, car interior temperature, battery, locked unlocked and device signal strength statuses work and when I manually start my car with my OEM key fob the runtime even shows up, but the remote start and stop features inside the linkr app report failure, trunk release feature wasn't tested It started getting late here, is there something I'm missing?

001A07233581

FAQ: Programming CARLINK, ASCL6, LINKR, MYCAR

Mon, 17 Jan 2022 10:06:40 +0000

To program your carlink,

make sure to follow their instructions on how to connect it to the EVO-ALL or EVO-ONE using their own HRN-LLRS-01 harness
setup the app for fortin
follow programming in car

Here is a copy of their guide. Please read attentively every step of programming since their is setup in the app you must first do. https://fortin.ca/download/64631/ascl6-install-guide-64631.pdf

EVO-ONE Programming

Following the RED LED on the BACK of the unit, not the one on top.

Igniton ON-OFF-ON (red led on evo will turn on solid)
Hit brake 4 times (red led will flash on each brake press)
At this point wait 10 seconds then shut off the car.

EVO-ALL Programming

Please first try the EVO-ONE. It was added to the EVO-ALL firmwares.

Otherwise, this older method is still functional.

Disconnect the 20-pin connector
Disconnect the 4-pin black connector
Press and Hold programming while inserting 4 pin connector.
Release when the LEDs are BLUE and RED
Press and HOLD programming button, wait until the BLUE and RED LEDs turn and then BACK ON. Release when they turn back ON.
Plug in 20-pin connector
Turn ignition ON, all three LEDS will turn ON
Wait 10 seconds, then turn off ignition.

Linkr lt2 and rfk411 at same time on evo one

Sun, 30 May 2021 03:47:44 +0000

Hello and greetings,

I have succesfully installed evo one and link lt2 on 2015 nissan sentra standard key. 3x lock works to start and shut down remotely. Linkr lt2 and all the associated functions work as they should. Evo one alarm with siren works fine with shock and glass break working well. I am trying to add rfk411 to the system and am having no luck. I have wired in in a 1 amp diode, band facing remote, on the white wire of the second plug(black) on the linkr harness but cannot program the rfk411 sucessfully, Followed the procedure, all lights etc. working as guide shows they should but no functionality after programming. Also, with rfk411 plugged in, I lose the start, stop, lock, and unlock fubctions of the linkr. I;ve also tried programming the rfk411 to the evo one without linkr in the mix and have nuccess.

Please advise.

Thanks!

2020 Silverado Linkr LT2 door locks not working

Thu, 10 Dec 2020 10:35:46 +0000

I installed the Fortin Evo-all with T-Harness on my 2020 Silverado 2500HD that has no Onstar, then added the Linkr LT2 and everything works except the door locks. I checked continuity of the purple and purple/white wires from the Evo-All plug to the pins on the BCM and the wires are fine. With the Evo-All disconnected I can control the door locks by applying ground to the purple and purple/white wires. I have performed a full reset of the Evo-All multiple times, and tried at least 20 different flash configurations and nothing. It seems as if the Evo-All is not applying ground for lock control, possible firware or module issue because the Evo-All is Flashing the Blue light for lock via the Linkr LT2 and the red and blue for unlock. Any feedback would be greatly appreciated.

mycar programming

Thu, 14 Feb 2019 16:00:10 +0000

When going through the pairing procedure of a mycar (ascl6, link6, teleconnect, carlink) to an EVO-ALL or EVO-ONE, send a Lock command from the APP instead of waiting for their autolearn at the last step of programming.