Questions & Answers - Questions récentes tagguées nissan-altima

2016 Nissan Altima PCM humming sound and park lights staying on

Thu, 07 Nov 2024 20:47:41 +0000

Installed compustar alarm with remote start using a EVO-NIST4 and diagram75491, d2d cable being used. For some reason the PCM is humming and the park lights are on, what can be the issue? Do I change out the power wire fuse to a 1 amp since it comes with a 30 but I am not using those, just the D2D as the diagram says.

Interior lights stay on

Sun, 30 Apr 2023 19:17:26 +0000

Altima 2008 coupe lights stay on, even if vehicle is off and locked. Once driving interior lights stay on as well. Evo nist1.

Brakes light up when remote starting but the 2010 Hybrid Altima does not start

Fri, 20 Jan 2023 12:25:16 +0000

This is a weird one, because the car remote starts pretty much every other remote start session. I'm not sure what's causing that as I checked the wiring and it doesnt seem like anything is wrong. So here it goes, when i try to remote start the car from far I see my brake lights turn on* (as in the brakes are being pressed) but the car does not start. the problem is mainly that the brake lights STAY ON unless I actually go to the car and start it myself, however even when i get to the car nothing pretty much works. I press the brakes myself and when I press the the push to start button it stays on lock (it goes LOCK-ACC-ON) so i pretty much freak out, unlock and lock mulitple times, press and depress the brake while keep hitting the push to start untill it goes off and then I manually start it.

INFO:
2010 Hybrid Altima (Push to start)

EVO-ALL

using RL1 red connector in the module

* passanger side brake light does not LIGHT UP, the bulb itself works only when i run the headlights but not when i press the brakes

2007 Nissan Altima red light flashing 3 times when trying to start

Wed, 05 Jan 2022 16:56:57 +0000

I have completed the install and programming everything seems to be done correctly. I did not connect the 3 wires to the bcm foot lock unlock and door pin because I don't want to. When I hit the lock button 3 times the unit clicks and attempts to start but then red light flashes 3 times and doesn't start.

installing Evo-All in 2008 Nissan Altima PTS Hybrid module not finishing programming

Tue, 30 Nov 2021 17:34:20 +0000

using installation guide #84521. get to last step in programming(# 8 flashing yellow) which I get once I turn off ignition (by pressing the PTS button once) i get a Red & Yellow alternating flash. which would mean Decryptor is ready right? steps do not mention decryptor at all. And I dont get the decryptor option in the Flashlink Software. Have confirmed Hybrid mode is on and even attempting rolling FW back for minimum required as listed in guide

Why doesn't 3X lock turn off my vehicle?

Tue, 27 Apr 2021 20:23:53 +0000

Nissan Altima 2008 PTS

EVO-ALL-NIST1 001A06848886

Guide # 84551

Blue led blinks twice while off from fob lock/unlock command.

Red led blinks and brake lights turn on after 3x lock, engine starts.

Red and Yellow led remain on while in remote start.

Blue led flashes twice from unlock, but not lock, command.

A1-A6 enabled

A7-A11 disabled (No support for OEM fob takeover before 2009)

B1-B2 disabled

C1 enabled

D1 enabled (15 minute runtime)

D2 disabled (this didn't help)

D3 disabled (so vehicle will stay on)

D4 disabled (not a hybrid)

Protocol - Fortin

No special functions

No RF kit

09 altima evo-all w/thar-nis1 tharness. Wanted to add siren and shock sensor need wiring diag.

Sun, 21 Feb 2021 20:54:05 +0000

Evo,all w/thar-nis1 t harness, oem remote, standalone. Green wires are for lock n unlock. Where is siren wire ?

OEM Remote Control for Altima 2007/2008

Tue, 15 Dec 2020 11:29:42 +0000

Has anyone been able to figure out a workaround to have OEM Remote Control ("Lock Lock Lock") work for the Altima 2007/2008. I plan to use a cell phone starter, and my biggest reason for wanting a workaround is so that I can use the "keyless" entry method of unlocking the car once I actually walk up to the car. I want to avoid having to unlock the car soley thru the cell phone app, but instead press the button on the door handle to unlock the car and not have it shutdown. Is this possible?

2015 Nissan Altima Ignition Ignition 2 wire

Wed, 02 Dec 2020 10:08:45 +0000

Not a question so much as an update to your notes. On the installation instructions it shows Ignition 2 as Pin 9 Black 24 Pin plug as a Pink wire. Vehicle I had it is not a Pink Wire it is Brown but when tested goes + when PTS is hit for ACC or IGN.

Remote Start for Nissan Altima 2008. Which product?

Wed, 01 Jan 2020 16:41:18 +0000

Hello,

I am just interested in installing a remote start for my NIssan Altima 2008. After using the website to show me which products are compatible, it gives me the EVO-ALL or the EVO-ONE and I'm not sure which one to choose. Is choosing one of these products all I need? or is there something else I need?

I am just interested in the remote start and nothing else. Also, I prefer to use the original key FOB to remotely start the car.

Thanks,

Got the evo rs evo-nist4. The diagram doesnt really explain what wires get cut and sliced were

Sun, 29 Dec 2019 15:41:04 +0000

I need help with the wires and what I'm adding them with.

I want to turn on alarm and add shock sensor and siren

Mon, 23 Sep 2019 18:22:38 +0000

I would like to add a shock sensor and siren to my Evo All. What do I need to make this happen? I know I have to go in and turn on the settings and I have the flash link.

Unable to program the key

Wed, 11 Sep 2019 03:17:49 +0000

Hi, I want to reset because I am unable to copy the key slide

Exceeded the limit for this car

unit number

نموذج رقم الوحدة : EVO-ONE

SN: 002B04016358

Can I use LINKR LT2 with EVO-NIST4

Mon, 09 Sep 2019 12:12:14 +0000

I ordred an EVO-NIST4 with flash link. It says it is compatible with most telematic & GPS modules including Smart Phone and compatiable with Long Range Kits. Will the LINKR LT2 work with this particular unit?

can i add Rf range extnder and Lnkr Lt2 bluetooth to the Evo All and if so what HArness do I use to connect it?

Mon, 09 Sep 2019 11:17:12 +0000

Can I hook up RF extender and LINKR LT2 on the EVO All. So for example, if i dont want to use remote i can use my phone and vise versa. if i dont want to use my phone i can use rf remote that is provided with crimestopper rf extender kit. thank you

2017 Nissan Altima check engine code P0462

Mon, 26 Aug 2019 15:27:00 +0000

I installed the Evo-All and everyting works correctly but my check engine light is on. I went and had it checked and it is throwing a code of P0462. Open circuit low input poor electrical connection faulty fuel sensor. This wasn't there before i installed it. Didn't cut any wires or anything like that. Maybe bad connections or bad module? everything works and starts just fine.

3x lock doesn’t shut down engine just accessories

Mon, 10 Jun 2019 22:35:40 +0000

2017 Nissan Altima Evo-All with T-harness in stand alone. 3x lock starts just fine. Accessories all come on inside, radio, a/c, dash lights. Problem is if I 3x lock to turn off car or let runtime timer run down to shut down car, accessories all turn off but engine does not. Only way everything shuts down after remote start is if I manually press the start/stop button in car. Also when remote starting parking lights flash as starting but don’t stay on to show car is running.

service number on unit is. 001A06 853354

2008 Altima PTS EVO-ALL, cannot shut down after remote start

Mon, 15 Oct 2018 16:35:35 +0000

Installed an EVO-ALL in 2008 Altima SE PTS. The EVO starts the car with 3xlock, but will not shut the car off with 3xlock. The blue led on the evo blinks with push of lock on oem fob, but only before a remote start. After car is running under remote start, the blue led on evo no longer resonds to lock commands.

So basically, the evo is seeing lock commands only before a remote start. After remote start, the evo no longer sees lock commands.

Also, the car shuts down after door is opened. All wires are connected as per instructions.

Any ideas?

No Start

Sun, 16 Sep 2018 07:26:28 +0000

EVO-NIST1 with the t harness all connected properly at the key port connector the ODBII connector and the brake pedal connector. EVO loaded with the latest firmware and programmed per the instructions and did get the flashing blue, yellow and red lights. I even added the REVO RF remote but when it comes time to remote start the car nothing. After pressing lock lock lock I see the EVO blue light coming one. Then the EVO does its cycle to red light and I get the brake light confirmations but no start. The dashboard does not even come on and I swapped between RL1 and RL2.

What Equipment is needed for a 2008 Nissan Altima PTS

Mon, 15 Jan 2018 15:44:50 +0000

I puchased the EVO-ALL with the THAR-NIS1. The directions are a litte misleading to me, the application guide shows this as being able to be used as a standalone remote starter. However the instructions show a seperate remote start as being needed. It shows I also need a seperate RF kit for that particular year Altima, however I see other technical questions being asked and the people are using the factory keyfob and are pressing lock 3x to remote start.

2011 Altima PTS 'No Key' on Instrument Cluster

Mon, 15 Jan 2018 10:43:20 +0000

2011 Altima Push-To-Start
Using T-harness. Connected to OBDII, Brake Pedal, Keybox.
Tapped into Brown wire on push-to-start button.
A1-A11, C1, D1, D1.2, D3 Enabled
Latest firmware for flasher and EVO-ALL

Went through programming sequence (with battery out of FOB). Sequence completed sucessfully ending with rapid-flashing yellow light. When activated with FOB inside vehicle, it starts fine with the 3x lock press. With FOB removed from vehicle, 3x lock press does not start vehicle. Vehicle displays "No key" message on instrument cluster.

I have tried to re-flash and re-program the EVO-ALL multiple times, all with identical results.

What am I missing here?

2012 ALTIMA WILL NOT START

Wed, 29 Mar 2017 13:36:55 +0000

Hi, I just installed EVO-NIST1 as per Installation Guide in my Nissan Altima 2012 (Push to Start - Auto transmission) for using my OEM Key Fob 3x to Remote Start , I plugged in all connectors and spliced 2 wires, the first one is the black/white from the EVO to the brown wire at the push button, the second wire is the parking light wire, it's the brown wire from the EVO going to the red/blue wire in the fuse box. I programmed the EVO and all lights appeared as expected, however, the car doesn't start remotely, i tried it with the key inside and still no luck, whenever i push the remote lock key i see a blue light on the EVO , the brake lights is off when trying to remote start , I plug the RL 1 to EVO , please tell me what I’m missing here

Firmware Vr.72-19

Can i install evo-nist on a Nissan Altima 2010 with steering lock fuse removed?

Wed, 15 Mar 2017 22:19:50 +0000

My Car's steering lock failed on me and i got stranded, i hit it with a hammer and it worked, immediately removed the steering lock fuse so not to face this again.

will the evo nist1 package still work for a remote start?

Nissan Altima 2008 hybrid bush to start evo all not working

Sun, 26 Feb 2017 14:07:12 +0000

I recently bought EVO ALL stand alone remote start, all wiring and programming done, on testing it start for 3 seconds then switch off repeated again and switch off again, then red light flashing 3 times.

please help

Hardware: v 6

fermware : v 71.29

service# : 003606004550

note : no flasher available

EVO All with T-Harness wouldn't remote start on Altima 2012

Wed, 08 Feb 2017 12:57:44 +0000

I purchased the EVO ALL for my Altima 2012, I installed it as instructed, I plugged in all connectors and spliced 2 wires, the first one is the black/white from the EVO to the brown wire at the push button, the second wire is the parking light wire, it's the brown wire from the EVO going to the red/blue wire in the fuse box. I programmed the EVO and all lights appeared as expetced, however, the car doesn't start remotely, i tried it with the key inside and still no luck, whenever i push the remote lock key i see a blue light on the EVO. I rechecked all connections and everything seems intact, plase tell me what i'm missing here.

Thanks.

Remote start does not work on Altima 2012

Wed, 25 Jan 2017 10:55:04 +0000

I'm having a strange issue with my EVO-NIS1 remote starter, I initially installed the kit without connecting the parking light wire, the remote starter worked well for 2 days. I woke up in the morning and the car battery was dead, I jumped the car but the remote starter stopped working, I checked the wiring and everything seemed fine, i reprogrammed the EVO with the flash link and reconnected the wires and did the programming as I did initially. The problem that I faced is not seeing any red or blue lights, It got stuck at the steady yellow (step 4). the car still works fine but without the remote starter which is still installed, the only time the remote start worked is when i was in the car already. I went back to connect the parking light and tried to program it again but i still got stuck at the steady yellow light. I don't know what to do to get passed step 4. Please help. Thanks.

2016 Nissan Altima PTS Take Over

Thu, 19 Jan 2017 22:33:38 +0000

I installed and evo one with a crimestopper remote start and everything works fine. however i noticed if I unlock the doors by pushing the button on the remote i need to follow the takeover procedure by pressing the PTS button twice as stated in the instructions, HOWEVER if I keep the key in my pocket and push the button on the door handle to unlock it does the takeover procedure automaticly without me having to push the PTS button at all. Can anyone else confirm this?

Will EVO-NIST1 support a manual transmission in a 2010 Nissan Altima?

Wed, 23 Nov 2016 16:49:03 +0000

I'm wondering if the EVO-NIST1 will support remote start on my 2010 Nissan Altima with PTS since I have a manual transmission. I heard an EVO-ALL with the harness would possibly work as well. I want to install it as a starter using the OEM intelligent key 3x lock button.

Thanks in advanced

2011 Altima Auto-headlights never turn off with remote shutdown with OEM remote

Fri, 10 Jun 2016 23:55:49 +0000

Hi, I just recieved my EVO-NIST1 and I'm loving it! The only two issues I have are:

1) Auto headlights never turn off if I remote shutdown and don't open the doors. I have confirmed that the door pink/black wire is connected by remote starting in the car then pressing the brake. The engine shuts off. It doesn't do this if I open the door before pressing the brake.

2) Doors don't relock when remote shutdown is engaged. I have to press lock a 4th time on my OEM remote to lock the doors and arm the alarm.

Rear Defroster - Nissan Altima 2012 2.5

Sun, 31 Jan 2016 17:43:49 +0000

Hi, I just installed EVO-NIST1 as per Installation Guide in my Nissan Altima 2012 (Push to Start - Auto transmission) for using my OEM Key Fob 3x to Remote Start and OEM Key Fob to Remote Shut Off.

Is it possible to switch on rear defroster /defrost when Remote Start ? if yes than where can I get the wiring connection diagram for Altima 2012 etc...

I'm using OEM Key Fob Only.

Thanks

Altima 2012 - Car Not Shut Off from long distance but Starts

Sun, 31 Jan 2016 11:38:12 +0000

Hi, I just installed EVO-NIST1 as per Installation Guide in my Nissan Altima 2012 (Push to Start - Auto transmission) for using my OEM Key Fob to Remote Start and OEM Key Fob to Remote Shut Off.

Note : Flashed with the Latest Recommended Firmware for Nissan Altima 2012. Configured first Mode (Remote Starter) - Options enabled (A1,A2,A3, B1, C1, D1, D1.6, D2, D5, D6)

Also configured mode bypass with same options mentioned aboved.

Ever things works as it should be,

From Distance (car) 1-8 meters when I press lock button x 3 times (OEM Fob key) car starts and when I press lock button x 3 times again car shut off.

From Distance (car) 10-30 meters when I press lock button x 3 times (OEM Fob key) car starts and when I press lock button x 3 times again Car NOT SHUT OFF. Until I walk in distance under 8-7 meters to car than if I press lock button x 3 times Car shut off.

What I don't understand if I've a problem with OEM Key Fob distance limitation than how come I able to Start Car from long distance ( 10-30 meters) but at same distance Not able to shut off.

Help me out with this issue, is there any optin that I need to enable or disable ?

2008 Nissan Altima engine shuts off when door opens

Sun, 24 Jan 2016 14:45:21 +0000

I have just installed the EVO-ALL in my 2008 Nissan Alitima (push to start). All features are working properly, such as door locks, lights, windows, and even the remote start. My only problem is that when the car is running, I unlock the door, open it and the engine shuts off. How do I make it so that my car remains running when I open the door?

Remote Start for Manual Transmission. 2007 Nissan Altima

Sun, 13 Dec 2015 11:30:23 +0000

Is the 3x Remote Start compatible with a manual transmission 2007 Nissan Altima?

2008 Altima Problems with unlock.

Sat, 21 Mar 2015 22:06:49 +0000

Installed an Evo-All in a 2008 Altima as a stand alone remote start with a FT-D100 RF kit. It is programmed On for "Unlock driver door only." The issue I am having is that when you press the unlock button once, the lights blink but the driver door does not unlock. Press the button again and the lights blink and all the doors unlock.

No installation sources for Nissan Altima - Push-to-Start (2007-2008)

Thu, 19 Mar 2015 21:42:27 +0000

I need but am unable to find installation help (wires, photos, guide) for Nissan Altima - Push-to-Start (2007-2008) on wirecolor.com. I can find the information for Nissan Altima - Push-to-Start (2009-2012). I think they are the same but not a hundred percent sure. Can anybody confirm that. Thanks.

06 Altima auto start works interrmittently

Tue, 03 Feb 2015 19:31:24 +0000

Hello I have a Fortin module starter on my 2006 Nissan Altima. The starter will work sometimes along with the door locks and trunk control. When everything is working the horn beeps with locking and unlocking doors.

As if a switch has been switched the remote buttons change and only one button both locks and unlocks door with no horn, no trunk, no starter.

This is an older unit so I am unclear if it is still dealth with. Are there any manuals availible?

Parking Lights

Sun, 18 Jan 2015 01:11:29 +0000

When remote starting my car, my parking lights never come on.

1. Are they supposed to be on?

2. If yes, how should I go about fixing it?

3. Will the lights remain on when I shift into drive?

This is for a 2011 Nissan Altima Push-To-Start. With the Evo-Combo for Nissan.

'08 Altima EVO-ALL, TNIS1, Compustar CM7200S no start initiation

Sat, 10 Jan 2015 09:36:37 +0000

Axxess branded bypass AX-ALL with AX-TIS1 harness and CM7200S remote starter. Bypass programmed correctly and door locks work with aftermarket fobs. I can't get the remote start to initiate start sequence. I assume that it is a setting in the options but I think I've tried about everything. The AX-ALL lights red and yellow light up, and the RS brain clicks through all three start attempts. No brake lights, no dash lights.

This is only 2nd time using Fortin.

Is tech support open Saturdays?

2008 Altima BCM lock/unlock slots are populated.

Fri, 09 Jan 2015 12:14:45 +0000

I am installing an EVO-ALL with TNIS1 and Arctic Start CM800 into a 2008 Nissan Altima SE. I am using guide # 12651. The guide shows that BCM slots 15 and 37 should be empty, mine are populated with blue/red in 15 and blue/black in 37. Should I connect to these wires or am I in the wrong spot?

Viper VSM200 with EVO-COMBO for Nissan Altima 2011

Sat, 03 Jan 2015 13:43:21 +0000

Once the VSM200 is installed to my Fortin, will all of the buttons within the SmartStart app function? If not, is there any way to get them all to function? Also, is there anyway to get confirmations on the smart start app?

I would like to know if the EVO-ALL for PTS Nissan Combo is compatible with the Viper VSM200 smartstart system?

Thu, 01 Jan 2015 23:56:04 +0000

I have a 2011 Nissan Altima PTS, with a keyport. I am looking to purchase an EVO-ALL Nissan system with a T connector, but I would like to attack a Viper VSM200 so that I can have Smartstart capabilities. Is this possible?

what am i missing for altima 2010 pts

Mon, 29 Dec 2014 10:31:40 +0000

ive installed the evo all with nist harness flawlessly on a 2012 altima. short story long, i ordered same setup for a 2010 from another dealer. wired the same way according to oem diagram, would not start car. i sent back to have module reflashed according to specs such as bypass on. module was sent back, i tried programming mod, it flashes correctly but when i hit the lock three times, i just get blue flashes, not red. car dont start. am i missing anything or is the programming not correct in flash

installed evo-one x and thar one on a 2006 altima

Tue, 23 Dec 2014 20:10:07 +0000

When initial install, the lights cycle between red yellow blue as in the instructions but and extra stage of red and blue together appears. as in the instructions i stop on blue and conntiue connecting the harness. all other step are as per the instructions. after install i try to program the remotes the led flashes but when i push the lock no parking lights flash. the remotes will not program.

2007 Altima auto headlight does not turn off

Fri, 12 Dec 2014 14:42:05 +0000

2007 Altima

First question: When the headlights are set to auto and I remote start the vehicle using a timer start function the headlights don't turn off when the remote start shuts off. Can the EVO-All shut off the headlights?

Similiarly if I remote start the vehicle and don't enter the vehicle and turn the remote start off the headlights stay on.

Second question: When I activate the remote start while vehicle is on/running to valet takeover, vehicle shuts off when I re-enter. I activate remote start before exiting the vehicle then use the remote start fob to lock the doors and car is running off remote start. I then unlock with remote start fob and enter the vehicle, but when I hit the brake pedal the vehicle shuts off. It should allow takeover as it does normally.

D

Wed, 12 Nov 2014 09:09:36 +0000

Bonjour,

J'ai un d

Is there anything else that I need to install my EVO-ALL on my 2011 Sedan Altima 2.5?

Mon, 27 Oct 2014 21:54:39 +0000

Are these ONLY 15 wires that I need to connect to install my remote start with this bypass, beside lock/unlock and lights/horn.

Remote start: Viper Responder One "2 ways single button".

Do I need to connect? - Ignition 2; - Starter 1 and - Starter 2; Accessory 1 and Accesory 2? I am very new to this product and not very familar with it. I am only working with Xpresskit and switching over to this units.

Bypass: EVO-All - Installation connection 5. D2D connection

Thank you in advance.

Here is my current connection from my Viper transponer one.

When I press the remote start button twice, it doesnt do anything accept long beep with red light from remote start button. What did i do wrong here? Thanks

2008 Altima Issue

Mon, 27 Oct 2014 05:53:22 +0000

When using an EVO-ALL on a 2008 Altima (push to start) with firmware 76.16, the car starts by only pushing lock once (so you can't lock the car without it starting). I can't get any other firmwares to start the car at all (not even light up when the car is locked). I tried the recommended 76.14, 76.09, 4.18, and 4.08 and nothing works. Is there a firmware that will start a 2008 Altima by pushing lock 3 times instead of once?

Is there an instruction on how to remove the instrument cluster on 2011 Altima to access to BCM?

Sun, 19 Oct 2014 01:45:55 +0000

Is there an instruction on how to remove the instrument cluster on 2011 Altima to access to BCM?

2008 Nissan Altima wiring info

Sun, 28 Sep 2014 03:17:54 +0000

I'm going to use a EVO-ALL to install a Avital 5303L alarm\remote start and looking at guide #3694 it does not list a 2008 push to start (AT) but I assume I could use the 09-12 guide. Am I right?

Looking at the 09-12 info, do i just need to hookup the wires labeled to make the whole system work or do I also need to hookup any remaining wires needed from the remote start system

What are all the Stand-Alone options?

Wed, 26 Feb 2014 09:56:36 +0000

With the different ways to get to Options, and different formats within those ways, I do not fully understand what I can do to program the EVO as a Stand-Alone. Options from the lower right button seems to have a lot more to them than Options from the upper tab.

Is there a manual that states what exactly each feature does?

Is there a setting that will prevent my car (2010 Altima) from unlocking the doors after turning off when the EVO runs for its allotted time (or quickly re-locking them)?

Thank you,