Questions & Answers - Questions récentes tagguées nissan-xterra

2006 nissan xterra evo all with prostart ct3371- starts but doesnt stop until you press the remote starter again

Sun, 13 Nov 2022 22:04:10 +0000

so i installed an evo all with a prostart remote starter ct3371from canadian tire. lock and unlock works and it also starts and stops with the remote. but we noticed that when we start it, it doesnt stop running after 15-30mins. it will only stop running after we press the remote start on the remote fob again.

i installed all the evo all and the pro start using guide 78161 which is for 2006 nissan xterra.

i installed all the solid lines from the starter. and the evo all. i also installed the broken line connections lock and unlock from the starter to the car and the broken line driver door pin connection from the evo all to the car. i also connection the GWR from starter to evo all.

only thing i skipped is the security LED connection which require cutting a wire thats why i skipped it.

am i missing something? do i have to connect all the broken line connection from starter to evo all?

thanks in advance for the help. i really appreciate you guys responding so quickly to questions. you guys are awesome. thanks again.

Where is VSS wire on 2012 Nissan Xterra VSS located? No RockFosgate audio.

Thu, 03 Mar 2016 21:22:43 +0000

Where is VSS wire on 2012 Nissan Xterra VSS located? No RockFosgate audio.

Adding Drone DR3400 to EVO-ONE

Fri, 15 Jan 2016 14:26:26 +0000

When adding a DroneMobile DR3400 to the Evo-one, are there any settings that need changed other than re-pinning the plug for the Drone? Will my current AX RF2 remotes continue to function the same?

I cannot get past step 5 on 09 xterra.

Wed, 13 Jan 2016 11:42:58 +0000

I have the Evo One with T-harnesses with everything connected and I cannot get past step 5. I get the solid yellow and red lights but do not get the fast flashing blue light to complete the step. Any help would be appreciated

EVOALL in 2011 Xterra won't lock immediately.

Tue, 22 Dec 2015 15:14:05 +0000

I have a customer with a 2011 Xterra, EVOALL, and Crimestopper RS4.

Every worked fine for a couple weeks, then last week he exited the car, locked the doors, then almost immediately unlocked to go back in and the doors would not lock again - until he waited 2-3 minutes and pressed lock on the RS4 remote a 2nd time.

Now the pattern persists. When he goes to lock the doors the parking lights flash but the doors do not lock. If he waits 2-3 minutes and tries again, they do lock.

Any ideas?

Verify Communications of D2D

Tue, 10 Feb 2015 00:19:02 +0000

I am unsure that my remote starter (a Viper 5706V) is communicating properly with the EVO-All.

I updated the flash to enable D2D, but it makes me suspicious that this category was hidden from me in main screen of the flash manager software.

Is there any way of telling if the D2D communcation is set up properly? Is the D2D comm just standard UART? If so is it human readable ascii or just a byte stream?

I am attempting to install this setup into a 2011 Nissan Xterra

When I attempt to remote start I, the ignition turns on but there is no starter turn over despite power at the starter pin. The alert on the dash also indicates that the key is missing. Alternativly if the key is in the ignition the car will remote start.

When looking at the EVO-All

The Yellow ignition light does come on

but neither the Blue or Red LEDs come on, this is despite having the GWR wire hooked to the 5706V

I have looked at the installation of the EVO-All with other DEI products like SmartStart but have not found anything about the 5706V, 5704, or 5702. Do you know if DEI uses the same D2D pinout across their products? When I opend up the 5706, I am pretty sure GND and Power traces are correct but the blue and white are not so obvious.

typo in EVO all and Evo one installation

Mon, 26 Jan 2015 22:52:18 +0000

Hi I have a few questions and comments.

First I just want to alert you that there is a mistake with installation guide #16431 Rev 20150107. and possibly more guides since those are duplicated.

The CAN-BUS pins are correctly labeled on the EVO One and the vehicle, however the wires drawn from the Evo One to the vehicle pins are backwards. I beleive this is also replicated in the corresponding EVO-All installation instructions (connection 3).

To put my question into context, I am installing an EVO-One into a 2011 Nissan Xterra

I was using the FlashLink updater to configure the EVO-One and the 3x lock remote start option is hidden. So is a 2011 Nissan Xterra compatible with the 3x lock remote start feature from the EVO-One?

Please confirm EVO-ALL compatibility with Xterra 2013-2104

Tue, 02 Dec 2014 13:13:23 +0000

The 'select by vehicle' compatibilty tool for 2013 & 2014 Xterra returns EVO-ALL as an option and calls out revision 20140507.

However....

20140507 only shows the Xrerra up to 2012. Can you confirm that it's good for 2013/2014 too?