Questions & Answers - Questions récentes tagguées no-led

EVO-ONE RF942 no antenna LED

Mon, 03 Feb 2025 14:37:39 +0000

Installed EVO-ONE car starts with OEM remote, and valet button works. After using the OEM unlock I tried to program 942 and can not ever get a blue LED on antenna blinking or solid, even following the on-off-on instructions. Valet button on antenna does not work. I checked out the antenna cable and it is good. I do NOT get a blue flash of the antenna LED when I plug in the antenna connector. Tried plugging the antenna into the Flashlink programmer and it can not be detected even when "special unit" is checked. Is there anything else I can do to determine if it is a bad antenna or something else ?

OVE-ONE no LED lights when 6 pin main harness is inserted

Fri, 25 Oct 2024 21:25:00 +0000

EVO-ONE with HON2 Tharness and EVO Start module. Programming with Flash Link Updater was completed successfully but when connecting 6 pin main power harness inside the vehicle while holding down the programming button, none of the LED lights illuminate. Power harness leads were tested with a multimeter and there is 12 volts but the EVO-ONE LED's do not light up so I cannot enter the dcryptor programming mode. Even though none of the lights on the EVO-One illuminate, the connected EVO Start module has a flashing RED led so there is definitely power going to the EVO-ONE.

Installed on a 2019 Honda Civic

RF642W No LED

Sat, 15 Dec 2018 17:37:24 +0000

I just installed an EVO-ONE in my 2016 VW Golf GTI Push-to-Start manual transmission using the T-Harness (THAR-VW1). It was tedious, but it went well. The EVO-ONE can remote start the vehicle using the OEM remote (3x lock).

Then, I added the RF642W kit. Just plugged the black harness from the RF642W into the "data link antenna" port on the EVO-ONE. I can't get the 642 to do anything. I tried to program the remote transmitters but I cannot get the LED to come on. I don't have a valet switch installed, so I'm using the ignition on/off method. On-Off-On does not set the LED. I've just setting the ignition "on" off 3 times and starting/stopping the vehicle 3 times (the instructions assume you have a key, not push-to-start). Nothing.

What should I do?

Evo one won't remote start

Fri, 01 Dec 2017 19:26:08 +0000

im reposting this question because my response was a little delayed.

I have a evo one remote start syesten in my 2012 Nissan Xterra. I installed it with with the T-Harness, install guide 33161. I also have the Fortin RF642W RF Remote Kit With Two 4-Button, 2-Way remote installed. The module programs to the car but the remote start does not work. the lock and unlock function works properly, the blue LED on the module will light up for both lock and unlock, but when I press the remote start nothing happens. No LEDs on the module light up, but the remote will flash green and beep. the red led under the yellow loop does not light up either. I also updated the module with the flash link updater, and cut the yellow loop for the automatic transmission. Any help would be apriciated. thank you

Evo One programs but won't remote start

Wed, 08 Nov 2017 07:42:10 +0000

I have a evo one remote start syesten in my 2012 Nissan Xterra. I installed it with with the T-Harness, install guide 33161. I also have the Fortin RF642W RF Remote Kit With Two 4-Button, 2-Way remote installed. The module programs to the car but the remote start does not work. the lock and unlock function works properly, the blue LED on the module will light up for both lock and unlock, but when I press the remote start it seems that the module does not recive the signal. No LEDs on the module light up. I also updated the module with the flash link updater, and cut the yellow loop for the automatic transmission. Any help would be apriciated. thank you

2014 Ford escape (non-push button) programs but won't start with oem 3x lock

Sat, 06 Aug 2016 20:29:37 +0000

Everything seems to be programmed correclty. The wireing harness is connected underneigth the steering column in two places, and the cam high and low are hooked up. C1 & D1 are ON in flash link manager. I got red and blue lights flashing after programming with two oem keys.

I read somewhere on the site that the lights tell a story. Keeping that in mind, I don't any lights when hitting lock or unlock. 3x lock just locks the car 3 times.