Questions & Answers - Questions récentes tagguées no

No parking lights

Tue, 24 Mar 2026 22:23:00 +0000

I need help please!!!

2020 toyota corolla (H-key) No parking Lights come on when the remote start is running,Installed EVO-ONE with T-harness TOY14,they only blink at the beginning and end of the remote start

NoParkingLightsDuringRemoteStart

Sun, 22 Mar 2026 06:32:23 +0000

Hello,2020 toyota corolla (H-key) installation with T-harness TOY14 no parking lights during remote start,only flashing when I remote start the vehicle,buy they turn off immediately.

This issue began after updating the evo-one firmware version,prior to the update the lights remained on for the entire duration of the remot start.

is there a setting I should change,or any wire I should check?

App wont start car

Fri, 09 Jan 2026 16:55:25 +0000

My evostart2 has worked very well for the most part for 5 years now. Recently it won't start with the app. I've reset my phone as well as the antena but won't connect to network. No lights on the antena when using app to attempt starts. 21 toyota tundra

Updated and no longer beeps when you press the HORN

Tue, 07 Jan 2025 11:12:23 +0000

Updated and no longer beeps when you press the HORN

In addition, the operating mode was set to 3 minutes but the actual runtime was only 1.55 minutes and a new key code was updated to solve the problem but more than once until the attempts were completed until this update issue appeared

Note that last year the device was working properly, please solve the problem for me from the bottom of the code

Serial Number:002B04045909

Evo-One

Note that previously before the update, the alarm was working properly after pressing it a second time and the engine works remotely, but now all settings are good, but the alarm does not work My car type Honda Accord 2014

Default settings were set to no avail

I hope who has the ability to help me reset the device to factory settings

Thank you very much

2011 Lincoln MKT key bypass programming will not show red led when pressing brake pedal.

Sat, 10 Feb 2024 17:00:22 +0000

I am trying to do the key bypass steps as described in the stand alone Evo All Lincoln MKT 2010-2014 installation instructions, but getting stuck after being told to insert the oem remote (without battery) into the keyport and press and release the brake pedal to get the unit to display the red LED. The unit only continues to disply the yellow LED despite me pressing and releasing the brake pedal (waiting 5 seconds between each push) up to 50 times. I am using firmware .57, as instructed in the instructions, and have flashed the unit mutiple times. I have also reset the unit and reflashed all to no avail.

Evo All w/ Evo Start no RF kit programming

Tue, 12 Dec 2023 12:48:15 +0000

2018 Ford Edge, Standalone Evo All install, and adding Evo Start. Can not get the Evo Start to program or "mate" to the Evo all. I do have temp, GPS, and bluetooth telemetry to cell via Evo Start but can not get any functions to work via cell app. Programming, I have tried hold program button, plug in black data, release on RED AND BLUE, push till RED AND BLUE, release while constant RED AND BLUE, ignition ON...but do not get the quick flash of RED AND BLUE w/ YELLOW ignition led on. Can you please guide me to what my issue is PLEASE? Remote start via factory lock unlock lock works along with door lock/ unlock like it should. Located in the eastern states. THANK YOU IN ADVANCE ! ABSOLUTELY LOVE THE FORTIN BRAND AND PRODUCTS.

money return for not recieving my keys

Wed, 29 Nov 2023 17:07:57 +0000

On sat nov 25th i order a key and never recieved a key then i ordered another 1 and never got it either, i have sent an email this morning and still no reponse.

sales order number 67606 and 67608

i would like my refund along with the extra charges that were also incured against my account.

evo-gmt1 no red light no start

Mon, 12 Dec 2022 18:25:24 +0000

2011 buick regal evo-gmt1 sn001A07v253955 . Blue light flashes with door lock / unlock . oem remotes. no red light , no start. thar-gm1 rev2 harness. what is the correct wiring diagram ? at the moment brown wire to can sw pin 1. brown with white stripe to green /gray parking lights . cannot get ahold of tech

impossible de faire la programmation

Mon, 05 Dec 2022 10:17:39 +0000

quand je branche module pour la programation je tien le bouon jusqua lumiere bleu et rouge ,je brancge mes connecteur ensuite jappuie 2 fois sur bouton pushstart . aucune lumiere allume

2006 nissan xterra evo all with prostart ct3371- starts but doesnt stop until you press the remote starter again

Sun, 13 Nov 2022 22:04:10 +0000

so i installed an evo all with a prostart remote starter ct3371from canadian tire. lock and unlock works and it also starts and stops with the remote. but we noticed that when we start it, it doesnt stop running after 15-30mins. it will only stop running after we press the remote start on the remote fob again.

i installed all the evo all and the pro start using guide 78161 which is for 2006 nissan xterra.

i installed all the solid lines from the starter. and the evo all. i also installed the broken line connections lock and unlock from the starter to the car and the broken line driver door pin connection from the evo all to the car. i also connection the GWR from starter to evo all.

only thing i skipped is the security LED connection which require cutting a wire thats why i skipped it.

am i missing something? do i have to connect all the broken line connection from starter to evo all?

thanks in advance for the help. i really appreciate you guys responding so quickly to questions. you guys are awesome. thanks again.

I bought an evo one, it worked perfectly with the original wear

Wed, 09 Nov 2022 17:25:48 +0000

Hello, I installed my evo one and it worked perfectly, but I know a lot of distance I didn't turn on so I bought the RFK441 kit. I installed it now. My car doesn't turn on either with the control of the kit or with my original key. I disconnected it and set it up again with only the key but it doesn't do anything to

Evo one only responds when its in valet mode

Mon, 02 May 2022 15:18:19 +0000

Evo one s/n 002B04108567 programs correctly with 2010 dodge challenger standard key wire to wire oem key fob and blue light flashes after when pressing lock or unlock , yellow light turns on when starting the car. The problem is minutes later the unit appears to end in in valet mode , red light on the side near yellow cut wire is on. When I take the unit out of valet mode , red light turns off but I no longer receive the blue light when locking or unlocking the car with the oem fob. When I attempt to remote start the car 3x lock the eed light turns on then the yellow light turns on but the car doesn't crank at all and only attempts to try 1x even though programming is set for 2x attempts. Then I get 4 clicks or flashes from the module. I followed guide #94481 for installation and have tried the basic bear options with my flash link 2 updater on 59.02 and 74 38 and 1 25 firmwares. I notice to anytime I try to run the module on the FL updater the FL updater has to be updated each and every time with 4 05 ? Any help appreciated , no oem alarm

2005 Jeep Grand Cherokee, Turns on but no crank, no start.

Sun, 16 Jan 2022 18:21:44 +0000

Installing Evo All, stand alone with Thar-CHR5 harness. Ignition and MUX wires are connected, module is programmed, key is programmed. Dash lights up, fuel pump buzzes but not start.

With the harness, I connected the yellow-yellow (ignition), green/red-purple (MUX), and white/red-pink/orange (starter) wires. is there something I'm missing?

Key Fob and Cluster

Wed, 01 Dec 2021 00:52:24 +0000

2007 A4. The key fob and instrument cluster was not original. So the immo cause the vehicle not start (cranks only). Can anyone recommend which one to purchase to defeat or bypass the immobilizer to get the vehicle to start?

2010 Ford Taurus standalone no tach signal

Sat, 30 Oct 2021 23:30:23 +0000

|nstalled EVO-ALL and THAR FOR4 into 2010 Ford Taurus standard key, standalone. Car will start and die after 5 seconds with evo red light flashing 3x for no tach detected. Used latest firmware and have tried backdating as well. Have also tried 2 other EVO-ALL modules with no success. Using Decryptor one key method. Serial # 001A07 153393.

Evo One not recognizing brake signal or key take over

Thu, 28 Oct 2021 14:06:51 +0000

I have an Evo One starts and stop from FTX64- 2W, tried it in two different vehicles same result. It's not recognizing key take over or 12v to black wire in 20pin connector to shut down. I read in a post, Derek mentioned wiring in a relay from the brakes that would send ground signal to the hood pin wire. Sounds like it will work. Will it have any adverse effect while driving, sending ground signal to the hood pin while driving if the key is not being recognized as being switched on?

Car attempts to start but does not crank

Sun, 24 Oct 2021 11:03:31 +0000

2015 Honda Accord coupe ex. It has been programmed correctly. Using a T-harness the Thar-one-hon3. It's a manual transmission with push to start and I put the car in ready mode using foot brake and E-brake. Both red and yellow led on module come on when there are supposed to but after pressing my OEM remote 3 times it appears to start but will not crank. I'm about to return this and seek another option. Any help is appreciated.

2020 Sienna crank no start

Mon, 22 Feb 2021 11:21:02 +0000

2020 Sienna will crank but won't start. Tried different moduals and different fobs. Still no start

no remote start

Thu, 18 Feb 2021 16:18:05 +0000

2006 ford freestyle. I have 2 keys. Hard wired in. The bcm i think is wrong for wire colors. it looks like the wires are in the blue connector and the - disarm is a light blue wire. could not find the light blue with black tracer. For disarm. plug in module goes to red let up insert first key to run position for 3 seconds. led lights on module turn red and yellow turn off remove key insert second key red light flashes 1 time remove key press and hold red light flashes 1 time let up on button .press fob lock 3x and no led flashing 10x. Any ideas would be great I have the lastes firm ware and udates in.

No remote start after install, no parking lights, brake lights light up.

Sat, 02 Jan 2021 14:42:33 +0000

Evo-ALL. 2012 Nissan Maxima

I have all wires connected. Do i need to connect any of the red plugs? No other options installed. I get no parking lights or car does not start when remote is pressed 3x. The horn beeps and the brake lights light up. Car will start when im inside and press brakes but no remote start.

Blue LED goes out during bypass programming

Sun, 08 Nov 2020 15:47:33 +0000

2008 Hyundai Sonata Evo-One doesn't have PATS wire so I didn't use red connector and light blue wires from 20 pin connector. I finished all the wiring and checked it million times. When I press programming button and plug the 6 pin connector, let go on blue, connect 20 pin, antenna, valet, and can bus, put the key turn to on position LEDs go out.

I tried turning on option 20.2 but when I plug the 6 pin connector all lights flash then they go out and nothing. I'm I missing something?

EDIT: Turned out my antenna was faulty, everything works great now.

HELP Nissan Altima 2013 Push Start

Tue, 03 Nov 2020 20:26:46 +0000

I ordered Nist4 with Evo all for a Nissan Altima 2013 Push Start. Its a plug and play on the BCM behind the cluster. Everything went fine with programming, but when I try to start the car while I am inside with press brake and push button to start gives me error i-key start error, the engine ticks no turn over.

When I am outside to remote strt 3xLock, it starts!! but inside using the normal car starting keyfob it doesn’t? I decrypted the module twice and also and sometimes it ticks no start. I programed it to car twice everything went well, all the flashing when I was programming went exactly per book, help please??

- Option D6 is on

- ignition turns on but error message i-key error refer to user manual

- car ticks when I press brake and push start, but no start and error message i-key error refer to user manual

- sometimes with remote start 3xlock the car starts sometimes it just ticks like I am inside the car

- SN: 001A07 119247 EVO-ALL

the evo does not detect the data

Sun, 26 Jul 2020 15:26:53 +0000

hi i have an evo one thats installed in a 2004 tahoe. followed guide 61101 and when trying to program the immobilizer bypass the blue light turns off and nothing else happens once the ignition is turned on. triple checked wiring and checked continuity. tried moving the wire to another leg of the bus distribution and that didnt work either.

am i missing some software parameter or something ?

SN:002B04 087218

tried software 70.18, 70.40 & 70.38

No crank when using remote start or using the key to start car

Thu, 23 Jan 2020 18:12:51 +0000

I updated the Evo one module to the current firmware and went ahead and re program process,during re programming process where I release programming button when blue/red led them plug in the rest of connector then 6x press programming button then red/blue blinks 5x when I try to start car it does not crank at all.

also it does not let me do the dcryptor it says it has reach maximum limit.

now I can't even start the car with the key,no crank at all.please I really need help,thank you.

2015 Mazda 3 PTS no yellow light during programming

Wed, 11 Dec 2019 12:46:37 +0000

Under hood there is a pin where instructions show a blank pin for jumper. Installing Evo-All with mazt1 t harness

Remote start no heat

Thu, 28 Nov 2019 20:23:20 +0000

Hi,

I just bought an evo-all with fort 3 harness for my 2017 F-150 2.7leb. Remote start works well and I enabled climate control and rear defrost with Forscan, but climate control center is dark and off until I insert the key. Climate control is manual. Tried all settings no luck. What am I missing?

blue light no start

Tue, 19 Nov 2019 09:37:09 +0000

i installed and programed and no start

i have the T harness

2012 Dodge charger push to start

when i try to start the car just the blue light comes on evey time i press the lock button on the OEM key fob and no start

2018 Jeep Cherokee push button start cruise comes on but won't set after install

Sat, 16 Nov 2019 11:22:03 +0000

I tried to manually start but it still didn't set.

no power to the camshaft sensor two wire prong

Tue, 23 Jul 2019 01:52:55 +0000

1988 honda civc

2016 Hyundai accent standard key Blue programming light turns off when I turn the ignition on

Tue, 07 May 2019 13:11:38 +0000

When installing the Evo one on my 2016 Hyundai Accent the blue programming light turns off when I turn the car on and the light comes back on when I turn it off have the can wires on the right ones do I need the can wires to use the remote start?What options do I need to change the service number is 002B07144688

2016 mazda cx3 starts then shuts off

Mon, 28 Jan 2019 15:23:51 +0000

only after sitting for several hours (overnight) car will remote start normally, then shut right back off. remote start works normally if car hasnt been sitting overnight/8 plus hours

RAM 2500 DIESEL KEY+EVO ALL - REMOTE NOT WAITING FOR A GLOW PLUG

Fri, 25 Jan 2019 09:03:38 +0000

RAM 2500 2014 6.7 DIESEL + EVO ALL STAND ALONE

3X LOCK REMOTE START WORKS FINE BUT AFTER IGNITION ON DOES NOT WAIT FOR GLOW PLUG

C1,D1,D2 ,AND DIESEL MODE IS ON

xtra wires? no red led when programming

Mon, 26 Nov 2018 11:46:50 +0000

2005 chevy silverado 1500

using install guide 61101 evo one.

during programming blue led goes off but no red led, I have verified obdII connection. firmware is 70.21

another question is should i wire in the unlock, lock, +ign, -ign, -disarm on the 20pin?

2006 Jeep Grand Cherokee DTCs after remote start is used

Sat, 10 Nov 2018 12:18:24 +0000

I purchased a evo all stand alone remote start with the T harness. After installing the unit I tested the remote start and everything seems to work as intended but I noticed that after using the remote start the check engine light on. So I read the codes and cleared them with my snap on solus ultra scanner. I then started the truck with the key to confirm they were cleared and all was good. I tried the remote start and again after it started the truck I have the same 3 DTCs

U110A Lost communication with steering column module - CAN- C

U0103 Lost communication with electric gear shift module

U1411 Implausible fuel volume signal received

The unit also does not turn on the heat or A/C. Nothing on the dash is on radio, gauges etc.

Lexus Gs350 and Evo One +INT-SL+ no work

Mon, 29 Oct 2018 23:22:41 +0000

Lexus GS350 2009 year North America ,Evo One + INT -SL+ no work

many times check connection -all is ok,program module ok ,problem is no start ,no reaction for teach INT SL to door lock -red light onn module stil light ,no flash rapidly .no reaction ,no start.

+12V diffrent color ,no black ,is white/red

Evo One Subaru Impreza 2014 standard key

Thu, 18 Oct 2018 22:10:47 +0000

I installing evo one to Subaru Impreza 2014 standard key Automatic Transmission.

many times check all connection

many times flash program - last time firmawe 79.49 ( this moment is blocked evo one but to many times flashing)

Car no start ,no reaction and blue led no flashing when door lock or unlock...

evo good programming and good decryptor -all is good but no blue led flash when used remote to lock car.

why evo is blocked ,no more flashing modules ??

why car no start-all connection check many times -all is ok

2017 Ford F-250

Tue, 03 Jul 2018 08:47:16 +0000

Vehicle 2017 Ford F-250

Product. Evo-all

Service # 001a06749339

That-ford2 t harness

Install guide # 59421

Installed according the install hour minus the lights . I don’t want my lights to work .

Having problems programming. I get all the way to the point of the the truck ingnition turning in and that’s it. After that the blue LED does not flash or do anything after the ignition is on.

The truck has a factory hood pin as well and the hood is closed . I also tried to reset the unit and start over in the reprogramming, that didn’t help.

registered and paid for one token...but there is no place to click on the token when trying to open the instructions ??

Thu, 21 Jun 2018 18:14:50 +0000

paid for the token, but didn't receive anything and the info is still locked

No Remote

Sat, 07 Apr 2018 20:37:10 +0000

Hello,

I do not have a Remote for my vehicule, how does one get into function programming withour one. Must I purchase a RF kit. The module seems to currently be installed properly. However I cannot Lock or Unlock with the EVO Start abd I cannot program the functions 2 mode 4 nor 20 mode 2 as I do not have a remote as per instructions.

remote start will only work when key is next to barrel ?

Sun, 18 Mar 2018 10:08:25 +0000

toyota 2010 rav 4 evo one with out t harness basically the evo one is not emulating the transponder please help is ther anything i can do to fix this or do i need to buy a evo key module to emulate the immoblizer

everything work just fine but remote start will not start the car it will just crank ....unless i put the key nest to the barrel then it will start

Jeep programming NO blue light

Thu, 11 Jan 2018 22:11:14 +0000

2016 Jeep Cherokee Evo All with Tharness 6, going through progamming and cant get past step 6, step 7 tells me to turn key to on and red light goes out, blue light coms on. Tried this several tiime, making sure I followed instructions to T, but blue light never comes on. One more thing...........I could not find the interior temp sensor, so i Never hooked up the yellow wire for it, does this matter? Please Help!

No flashing blue light during programming.

Fri, 08 Dec 2017 20:33:28 +0000

I have a 2013 Kia forte. I Installed the evo one using thar-one-khy1 t-harness. I have programmed both the remote start and bypass sides of unit but i do not get a flashing blue light during programming through can bus. When I turn key to on the blue light goes out and doesn't flash. I have verified that i have the can wires correct. They both show 2.3v. Vehicle does not have pats data wire or immobilizer

2017 Tundra Cranks only

Thu, 07 Sep 2017 09:44:39 +0000

Car: 2017 Toyota Tundra G Key

Using the T harness.

Module Serial: 002B169870

I can not manage to get the car started, all it does it cranks. I have quadruple checked the wires and did a re-installation twice.

Firmwire is all flashed to the lastest version using the flashlink.

My troubleshoot:

I disconnected the TPMS/Sil Data plugs, tried starting the car, still cranks only.

Disconnected the light blue/black wire, tried remote start, still cranks, put the key next to the barrel, still only cranks as well.

I checked to see if there was an issue with the ignition wire, yellow wire is connected to the pink T harness and everything looks good there.

Still cranking.

Flashlink:

What I have on:

2.4

4.1

6.1

7.1

8.1

9.1

9.6

10.1

11.1

12.1

13.2

14.2

15.1

16.5

18.1

19.1

20.6

24.1

26.1

29.1

30.1

31.1

32.1

33.1

34.1

35.1

36.3

37.1

38.2

39.1

On the module, when I lock and unlock, I do indeed get a blue led light.

At this point, I am thinking the module is not syncing with my key, is this a module default or could it be that the T harness is defect or improperly pinned as I've heard stories of them being pinned incorrectly.

Thanks.

how to get the door locks and foot brake working through data.

Sun, 14 May 2017 12:41:03 +0000

2010 tiguan. ct4311tw remote with evo-all and tb-vw bypass. evo-all programmed and the car remote starts but no shut down with brake and no door locks. Hard wired from remote to evo-all. Rechecked options and reset some. Now starts and dies and still no locks. Tried another cable, then another evo all same thing.

2015 Mazda CX-5 will not remote start

Sun, 12 Feb 2017 17:36:44 +0000

Wired and installed EVO ALL according to Guide 62951. I did not connect the park lights. All programming steps worked according to guide.

When I attempt to remote start by pushing lock 3X on the fob, the module will light up as follows.

The red LED will light up. 2 seconds after the red LED lights up the yellow LED lights up. They both stay on for 8 seonds and then both turn off. The process repeats a second time about 4 seconds after both LEDs turn off. After the second time nothing happens.

The blue LED on the module does flash when I hit Lock/Unlock on the fob.

I have tried remote starting with the Dark Blue wire for the safety switch grounded and not grounded with no difference.

The module has hardware version 6 and firmware update is 71.39. Options C1 and D1 are selected.

No LED's on unit after initial install

Sat, 19 Nov 2016 12:58:56 +0000

I completed all the intall wiring on my evo one on a 2007 mitsubishi eclipse, updated the bypass and remote start and when I plugged the unit in, I didn't see and LED's light up at all. Tryed to program the bypass, no LED's. removed the unit and tried to check the programming on the unit and it all seems to be fine. Looked in the Questions on the support site, and found that perhaps a master reset needs to be done. I can't seem to get any response from the unit on the car to do anything so I can't get into the programming mode to reset and can't get the red light during the master reset. What can I do?

2015 Outlander Sport USA no parking lights

Wed, 02 Nov 2016 13:26:45 +0000

I have a 2015 Mitsubishi Sport USA standard key start. I installed the EVO One with no problems, except wiring diagram shows no connection to parking light for start indication and status. All other models either show using 2 diodes and connect to parking light left and right side, or using turn signal lamps but not this model. If this model uses the can bus to flash lamps, it does not work. Any special settings using flash manager? I see none listed.

Using guide # 16831 you can see no connection. Any help would be appreciated.

2011 Silverado 1500 WT

Wed, 06 Jan 2016 08:52:13 +0000

Installed EVO-GMT4 and used provided T-harness for use as stand alone unit. Unit programmed according to steps in manual. Disconnected unit and updated to 70.18 using Flash Manager and FLU unit and and decrypted as well. All went well according to Flash Manager. Verified options C1 and D1 were enabled. Reconnected unit to vehicle and blue light flashes each time lock button is pressed, but vehicle never tries to start.

still need anwser to my question.

Thu, 31 Dec 2015 17:20:22 +0000

at end of the programming i get 10 red flashes then 10 blue.....ignition turns on the off as it is supposed to......doors are closed and lock pushed 3 times and no start...i get 1 blue flash with each lock push.....2008 ford edge....

Ok. im officialy done. i dont understand anything, great tech support. sending back for refund and buying different brand that will take the time and effort to offer real tech support and anwser questions(not just state what the instructions say).

2009 Hyndai Sonata

Tue, 29 Dec 2015 04:26:40 +0000

2009 Hyndai Sonata

No immobalizer (Don't have a Green data wire but have Hyndai alarm system and security LED)

Guide # 23951

My 2009 Sonata does not have a Green immobalizer wire at the driver kick panel white connecter. However do i still need to make connections between D4 tol A20 and D6 to A10 ? (In the Guide it shows D6 tol A20 and D4 to A10 but when we trace the wires the connections are in between D4 white green to A20 and D6 white red to A10 )?.