Questions & Answers - Questions récentes tagguées red

Red LED light will not do anything but stay on

Tue, 03 Feb 2026 11:33:52 +0000

I’ve checked every single wire so many times been working on it for two months. Red light will only stay solid so I’m guessing programming issue company I bought it from won’t help. Please help me somebody. also kid did not come with a remote start. I am using OEM key 2005 Honda CRV

2020 Honda HRV - Stuck on Flashing Red Light

Mon, 24 Nov 2025 03:12:33 +0000

Hello,

I am trying to install the Fortin Evo-One into a 2020 Honda HRV (standard key), however I am unable to get past step 5 of the programming process. When I go to program the Evo-One, I am able to get to the blue/red blinking light step, however once I turn the key to ignition position the Evo-One blinks red. I am using the EVO-ONE-HON2 T-harness. I have tried the "FAQ: RED LED STUCK ON" method mentioned in another post, but unfortunately that did not work. Any help would be greatly appreciated.

2011 Lincoln MKT key bypass programming will not show red led when pressing brake pedal.

Sat, 10 Feb 2024 17:00:22 +0000

I am trying to do the key bypass steps as described in the stand alone Evo All Lincoln MKT 2010-2014 installation instructions, but getting stuck after being told to insert the oem remote (without battery) into the keyport and press and release the brake pedal to get the unit to display the red LED. The unit only continues to disply the yellow LED despite me pressing and releasing the brake pedal (waiting 5 seconds between each push) up to 50 times. I am using firmware .57, as instructed in the instructions, and have flashed the unit mutiple times. I have also reset the unit and reflashed all to no avail.

Audi 2013 S4 DSG - Fortin ALL getting stuck on step 7 with 3 x red flashing lights

Fri, 22 Dec 2023 11:16:42 +0000

Just installed a Fortin ALL with the Audi T Harness on a 2013 Audi S4 DSG. UK right hand drive car.

When I go to try and get the unit to read the key data I am just getting 3 red light flashes on step 7, everything is fine up until that point and the car operates as normal.

When I then put the flashlink back onto the PC software it says invalid key data. Any ideas? I have checked all wiring, also checked status of CANBUS with zero issues showing so I know that wiring is good.

Serial no for module is : 001A07445150

Solid red led on my evo one

Tue, 14 Nov 2023 16:12:33 +0000

When I press the programming button and plug in the 6 pin harness I get a solid red led. how can I do a full reset on the unit and start over? the sn is 002B04 310017, any help would be appreciated, thanks.

On step 6 the yellow light stays on solid, no red

Wed, 09 Aug 2023 14:36:29 +0000

all goes well till step 6

evo-gmt1 no red light no start

Mon, 12 Dec 2022 18:25:24 +0000

2011 buick regal evo-gmt1 sn001A07v253955 . Blue light flashes with door lock / unlock . oem remotes. no red light , no start. thar-gm1 rev2 harness. what is the correct wiring diagram ? at the moment brown wire to can sw pin 1. brown with white stripe to green /gray parking lights . cannot get ahold of tech

Red light disappears and Blue light stays solid

Sun, 05 Jun 2022 02:22:04 +0000

Hello, I have a 2015 Infiniti Q70 and when i program the module, I can get up to step 8 without any issues. When I press the brake for the second time, the red and blue light comes on, but after about 1 second, the red light disappears and the blue light stays solid. I'm unable to complete the programming of the module. Verified all connections are tight and correct. Please help!

Red and white wire came out of harness where does it go

Fri, 15 Mar 2019 01:04:45 +0000

I have a red and white wire with the connector pin on the end and it is not in a connector. One end of that wire goes to my smaller ignition t wire harness so I know it goes somewhere just dont know where.

xtra wires? no red led when programming

Mon, 26 Nov 2018 11:46:50 +0000

2005 chevy silverado 1500

using install guide 61101 evo one.

during programming blue led goes off but no red led, I have verified obdII connection. firmware is 70.21

another question is should i wire in the unlock, lock, +ign, -ign, -disarm on the 20pin?

CX-3 won't start

Sat, 06 Jan 2018 14:50:00 +0000

After the remote start fails I get 3 red blinks from the module. No tach is the code but I don't know which cable is messed up. I have the evo-all hardware ver 6. Service # 003606005190. Also I'm not sure if I have the correct setttings selected.

2013 Mazda CX-5 programming issue

Mon, 16 Jan 2017 10:20:22 +0000

Difficulty programming unit. First had issues getting the module to learn the keys but realized I had low voltage. Charged battery and went through all steps up to 25 (towards end of CAN programming). At the end of sequence I received the blue light and it went off, then waited about a minute or longer, but never received the red LED. I've been through all steps including 1-12 and starting at 17, 18 and 21 but without success, have reset and resent data, but usually only receive flashing red. How can I completely start over as the unit seems not to fully reset after master reset and only get flashing red after going through 1-12 again. What process where should I start? Thanks.