Questions & Answers - Questions récentes tagguées smartstart

EVO-ONE with DSM550 AND Coolstart/Crimestoppper Remotes

Sun, 24 Oct 2021 17:37:32 +0000

I saw that the EVO-ONE now supports the DEI DSM550. Is it possible to connect both a DSM550 and a Coolstart/CrimeStopper REVO4 kit? If so, do any connection or programming changes need to be made?

EVO-ALL - OEM Fob not working to unlock after remote started. TPMS is cut and works.

Thu, 16 Jan 2020 17:40:44 +0000

I flashed EVO-ONE to latest firmware, used the wizard to set my settings, then went into pro mode and followed the steps in documentation to select XL202 RF kit, and installed in the vehicle. The SmartStart module is not yet installed. 3x lock works with OEM fob but once started, the OEM fobs no longer work to lock/unlock the doors. I did cut the TPMS wire and does not flash when started with key or after key is in ignition and turned to ON. I did test alternating the D6 and D4 wires on the cut TPMS wire but still had no unlock from fob after remote start.

My suspicion is that since the TPMS light doesn't flash in standard operation, enabling the RF kit might have something to do with this but since I didn't test the install before I enabled that, I'm not sure. Is there something else I might be missing?

Evo-One and SmartStart - Alarm notifications

Mon, 16 Dec 2019 13:22:07 +0000

I installed the Evo-One in my 2012 Audi A4 and I absolutely love it. You guys made a fantastic product. But I'm wondering if I install a SmartStar module, connected to the Evo-One with the data link cable, if the alarm in the Evo-One is triggered, will that information be transmitted to the SmartStart so that I can receive a notification on my phone through the SmartStart app?

Did Fortin get the dsm550 working with the evo-one evo-all

Mon, 20 May 2019 13:09:16 +0000

Did Fortin get the latest directed smartstart working with the Evo one/Evo all?

Evo-All, smartstart and prostart module install help please!

Tue, 02 Apr 2019 00:34:09 +0000

I recently purchased a smartstart module in hopes to add it to my prostart and EVO-ALL setup I currently have. I don't know what wires go where or if this is even possible as the data link cable seems to feed the prostart module and there is nowhere to plug in my smart start module. Sorry this is confusing I know. The wiring guide describes me plugging in two connectors to the prostart system and one four pin connector into the evoall which I can't seem to see where it goes and what all is involved. Any one help please. If I have it connected to my prostart module do I even need to connect it to. The Fortin bypass module as well?

Viper smartstart not communicating with EVO ALL

Wed, 06 Feb 2019 10:18:47 +0000

I've installed a VSM350 in my 2008 Grand Cherokee, following the instructions (splice grey wire with black, plug in connector). The VSM350 has been activated by a local dealer and my viper online account is properly set up. I can update GPS information via the smartstart app (this confirms unit is powered up and communicating with the internet properly). I am not able to lock, unlock, or remote start using the app. When I attempt to lock/unlock or start, I receive the message "unlock failed at [time]" I have enabled H4 via flashlink. I live in a major city and the vehicle is parked outside, the issue is not related to cellular coverage; the app reflects that the vsm350 has 4 or 5 bars of signal strength.

I appreciate any suggestions to enable the smartstart to communicate with the evo-all to enable the lock/unlock/remote start.

Thank you

Programming EVO-ALL / CHRT4 with SmartStart VSM350

Fri, 01 Feb 2019 11:51:55 +0000

About a month ago, I successfully programmed and installed an EVO ALL with CHRT4 in a 2008 grand cherokee. The 3x lock would successfully initiate a remote start.

I recently removed the EVO ALL to reprogram it with flasklink to enable H4 (smartstart). Upon reinstalling EVO ALL, I no longer had blue lights. I reprogrammed to the key and got the blue light to illuminate when clicking lock button. I connected the yellow to the yellow for ignition during initial install and that is still the case now. This yellow wire splice is the only wiring i've done outside of installing the CHRT4 harness.

The current issue is that after reinstalling the EVO ALL, I do not get a red light on the EVO ALL after clicking 3x lock. The 3x lock is still enabled in flashlink, in addition to H4 being enabled. EVO ALL was already (and still is) flashed to the latest / best / recommended firmware. Given my inability to remote start with 3x lock before even connecting the smart start, i have left the smart start unplugged until i can resolve the failure to start with 3x lock using the key. I have tried re-flashing the evo-all with latest firmware in flashlink and starting over but am in the same position where i get blue lights but no red, and thus, no remote start using 3x lock.

When vehicle is started via the key in ignition, EVO ALL gets a solid a yellow to indicate the evo-all knows it has ignition.

My question is: What I'm doing wrong or do I not have connected properly to get my red light back after 3x lock so that the vehicle can start. Does H4 prevent use of 3x lock remote start?

Cold start mode with telematics

Sat, 01 Dec 2018 12:50:00 +0000

Is there a way of enabling cold start mode with a drone installed on an evo one?

Programing VIper Vsm 350

Tue, 26 Dec 2017 21:53:54 +0000

I upgraded to the 350 from a 250 and now I only get 15 min. run time need to get more run time but can't program it.

Bluetooth interface wiring

Mon, 09 Oct 2017 17:45:45 +0000

i have EVO-ONE installed working with OEM remote. Im trying to add a bluetooth interface to it. i want to know how to add the Directed Smart Start Bluetooth. see installation info the the bluetooth below.

https://cdn.instructables.com/ORIG/FGM/ZCM3/IC6HWDYC/FGMZCM3IC6HWDYC.pdf

VSM200 smartstart to EVO-all wiring different than posted at Fortin

Mon, 09 Oct 2017 06:13:21 +0000

http://manuals.solidsignal.com/DSM200_QuickInstallGuide.pdf

I can not get any communication (green led not coming on) What loop should I cut? Brown or White?

I have H4 activated in options.

Any help would be apprecitated.

Evo-One plus Viper remote start?

Fri, 18 Aug 2017 08:34:30 +0000

Okay, ive noticed that the only way to get status feedback is to use a Viper remote start while using a smartstart system. My question is this.

Ive got an Evo-One, can i add a viper remote start with smart start? or would I need to swap out the evo-one for an evo-all?

Viper 5901 Smart Start

Sat, 29 Jul 2017 19:11:43 +0000

Have Evo all and want to add a Viper Smartstart 5901. I was told it's an easy install but not sure where to find the information. I was told to buy an XL202-RFTD. I did and I'm lost on what to do next. Any directions you can provide?

Can you have Viper Smart Start and an RF kit for backup on an evo one?

Tue, 17 Jan 2017 10:30:09 +0000

Insall is on a 2008 ford explorer. Customer would like smart start and an rf kit.

EVO start APP

Mon, 26 Dec 2016 11:05:52 +0000

Hi, is there anything need to use the EVO start app? I have the EVO-ALL

Wiring/Programming EVO-ONE w/ DSM300 SmartStart (2015 Subaru XV Crosstrek PTS)

Mon, 12 Dec 2016 02:50:30 +0000

Installed a EVO-ONE into my 2015 Subaru XV Crosstrek w/ Push-to-Start. I have no issues with the remote starter, bypass, locks, etc. Everything works great with a Fortin 2-way RF kit - which I am still temporarily using until I figure out how to get my DSM300 Smartstart to work. I didn't find the Smartstart guide particularly useful in regards to wiring it up to the EVO-ONE for my application. I had programmed the remote start to XL202 and grounded the gray D2D mode cable as per the Fortin guide. Can someone clarify if I am to use the white D2D connector that is included with the Smartstart's multi-connector harness and does it plug into the larger antenna port? Or do I need to make up a cable to go to the black Fortin Data-Link/Flashlink Port? Do I assume that I will have to power the Smartstart separately using its own 2-wire harness w/ 3-Amp fuse since the EVO-ONE isn't providing 12-Volts from the data ports? If so, do I remove the 12V power on my connection back to the EVO-ONE? I tried powering them separately and just leaving the data wires + ground, but I could not pair the Smartstart to the EVO-ONE; I sent a lock command which the Smartstart app said was successful during the pairing process as per the instructions I found, but I couldn't get the EVO-ONE to acknowledge the signal to pair the Smartstart. I hope someone can steer me in the right direction. Thanks

- Chad

2015 Lexus IS250 TRUNK RELEASE via DEI SmartStart APP not opening with Evo-All

Sat, 19 Nov 2016 21:29:59 +0000

I would like to know if there is an option to enable trunk realse with Evo-All.

I have Firmare 79.36 installed and I used guide #23781

the option for trunk release is (ON)

I also have RF Kit (ON) for DEI SmatyStart.

The DEI smart start does send the signal to the Evo-All and the lights flash, but the trunk does not open?

The trunk release still functions with the key fob.

The DEI smart start also locks and unlocks all the doors fine and also starts the vehicle just fine, other than no dirct feedback to say that the car is running.

evo-all and smart start/rf kit

Thu, 03 Nov 2016 18:56:14 +0000

.I know i can use smart start with the evo all but can i also use an rf kit? or does it have to be one or the other?

evo-all + DSM300 Smartstart

Sat, 02 Apr 2016 13:59:49 +0000

I have a 2009 Infiniti FX35 with evo-all with the T-harnes and added a Directed DSM300 smartstart module.

I have two issues;

1) when I remote start the car everything is fine and the doors remain locked. When I remote shutoff the car, the doors unlock. Is that supposed to happen? It happens with both the smartstart and 3X lock method. I'm worried that after the 15 minute timer is up on the start and it shutsdown, the doors will unlock.

2) the smartstart will start the car but I can not unlock and lock the doors, I have plugged the unlock/lock wires into the bcm and when I test the lock/unlock on the smartstart, the blue light flashes once so I'm pretty sure its getting the signal from the smartstart module. But the doors dont lock or unlock, could this be a grounding issue or something?

Programming SmartStart to work with Evo One

Tue, 15 Mar 2016 12:43:22 +0000

Hi,

Recently, my 5amp fuse blew. Since relacing it, my SmartStart hardly works. I wanted to know if you can email or send a link to the guide to program the SmartStart unit to the Evo One so I can try to reset everything. Thanks.

2013 F150 EVO-ALL, added SmartStart but lock/unlock doesn't work

Sun, 06 Mar 2016 22:07:33 +0000

Everything works great using the fob itself (OEM) and I have it setup for lock-unlock-lock

SmartStart VSM300 installed today, flashed to activate RF unit in EVO-ALL.

SmartStart unit starts the truck fine, but the lock/unlock does not work through the app/smartstart.

it appears to "send" the command for the lock/unlock, but it does not lock/unlock without doing it on the OEM FOB.

Any thoughts?

That said, could this be because I DO NOT have the wires tapped at the BCM for lock, unlock and the door pin? It didn't say they were required connections on the basic (use OEM fob) install. However, are they required to get the SmartStart/RF unit to lock/unlock the truck?

Joe

Can I activate EVO ONE via a pulse?.

Tue, 09 Feb 2016 20:41:14 +0000

Is there any way to activate EVO ONE remote start using a pulse trigger (not data link) like the activation wire in other remote starters?. The idea is for Telematic devices are not compatible with FORTIN's.

can I hook up a viper smartstart vsm200 to my stand alone evo-fort 1

Wed, 16 Dec 2015 20:21:48 +0000

I have a evo-fort1 hook up in my 2012 ford fusion with Crimestopper revo 4 and want to hook in a viper smartstart vsm200 can I do this and how should I wire it....

Telematics not powering up

Sat, 21 Nov 2015 20:36:36 +0000

So I installed an EVO ALL on my 08 Infiniti G35 and I have another thread here where I basically realize I need to use the telematics to start the car. I connect the telematics (directed DSM300 smartstart) per the instructions here and it powered up but then the harness on the EVO must have come loose. I went back and looked and reconnected and it started up and went to lock signal and I had good reception when I went to register it but then *poof* it stopped working. Any ideas? It won't power up and Im wondering if there's another option I should check in the settings other than the one for smartstart in the RF section. Thanks!

How to power EVO-ALL and telemematics through datalink

Sun, 15 Nov 2015 08:32:47 +0000

So I poked around and couldn't find what I was looking for. I'm installing an EVO-ALL and DSM300 smartstart today and I see the EVO needs a 15A fuse for power and the smartstart module comes with it's own 3A fuse. My question is whether the smartstart can power the EVO through the datalink cable? I guess that question is whether the smartstarts 3A fuse is enough or should I go ahead and just cut the datalink cable and power the EVO separately? I think this question would apply to all telematics.

nissan pts standalone and smart start

Tue, 14 Apr 2015 14:31:55 +0000

So im installing a smart start with a evo all stand alone in a 2013 murano. I have 2 questions. 1: do i have to hook up the lock out outs from the smart start to the evo then pin the evo lock wires to the bcm? 2: will the evo pop the liftgate through data when using the smart start??

Evo-ALL standalone with both XL202 and Smartstart - 2012 F150

Wed, 25 Mar 2015 21:51:42 +0000

I want to use an EVO-FORT1 to do standalone with both a XL202 and a SmartStart. Normally I splice the datalink cables together to create a new harness for this, but what about the programming in Step 5 for the Evo? The XL202 and SmartStart are different options..... which one should I use? Or will this work at all?

Honda CRV + SmartStart engine shutdown & restart

Tue, 10 Feb 2015 17:08:20 +0000

I have a weird problem with a 2014 CRV + SmartStart + EVO-ONE + THAR harness combo.

Everything has been working flawlessly for 2 months, but now the customer reports the engine shutting down and then restarting 3 seconds later, whenever he issues an unlock command from the SmartStart. Unlocking the door by factory key works fine, however.

Any idea where I should start troubleshooting? Nothing has changed since the original install.

EVO ALL smartstart doors trunk unlock no crank

Thu, 29 Jan 2015 13:18:38 +0000

When I press start on the the app, sgnal gets to the evo red led flashes dashboard ligths up but does not start.

sn: 001a06289845

firmware: 70.16

EVO-ONE/SmartStart statuses...

Tue, 20 Jan 2015 16:17:48 +0000

Is there any option in the EVO-ONE menu items that will enable the SmartStart to provide the statuses in the SmartStart app (doors: locked/unlocked, ignition, trunk, etc.)? Plans to get this to work? Currently, I get the error message in the SmartStart app that it's unable to interpret the info from the server. NOt sure if it's something with the EVO-ONE or something associated with Viper/Directed.

Honda CRV + EVO-ONE troubleshooting

Sun, 04 Jan 2015 09:42:26 +0000

2014 Honda CR-V + THAR-ONE-HON-2 + EVO-ONE

Having some strange issues with this car. Hooked up the wiring, bypass programs OK, and the RF kit worked fine for the first 30 minutes. (DEI SmartStart)

Now it seems like there is no communication between the Evo-one and the car. Engine running, no yellow light on Evo-one. No RF kit will program any more. I'm using the harness so it's pretty much plug and play. Bypass programming works fine still.

Scratching my head on this. I even tried a 2nd Evo-one but the same problem presents itself now (bypass programs ok, but there seems to be no car communication). Any ideas?

Viper VSM200 with EVO-COMBO for Nissan Altima 2011

Sat, 03 Jan 2015 13:43:21 +0000

Once the VSM200 is installed to my Fortin, will all of the buttons within the SmartStart app function? If not, is there any way to get them all to function? Also, is there anyway to get confirmations on the smart start app?

SmartStart EVO-ONE Hookup

Fri, 02 Jan 2015 19:55:55 +0000

I'm testing a StartSmart to my EVO-ONE but I'm having trouble with the "Program your remote" step. I can actually hear the SmartStart buzz when it receives the lock command but the remote programming fails (parking lights don't flash).

I followed the EVO-ONE + SmartStart instructions and modified a Datalink cable to fit (and grounded the grey wire). I noticed this is the only RF kit that plugs into the black Datalink port of the EVO-ONE, not the small blue port. Is this correct?

start the car using both 3X Lock Remote Starter and Smartstart

Fri, 02 Jan 2015 18:18:55 +0000

Hi,

I would like to be able to start the car either with the manufacture OEM remote via 3X Lock Remote Starter or using the Smartstart app

2015 LEXUS RX 350 EVO-ALL Stand Alone with DSM200 setup

Thu, 01 Jan 2015 18:23:53 +0000

Hi,

2015 Lexus RX350 to be used with EVO-ALL + DSM200 (SmartStart)

Would the options should be

A1 through A11 ------------------------------------------------> ON

B2 - Data-Link Remote Starter Mode --------------------> ON? (if connect SmartStart using data-link)

C1 - OEM Remote Monitoring -----------------------------> ON

D1 - OEM Remote Stand Alone Remote Starter ------> ON

D1.6 - 15 minute runtime -------------------------> ON

D5 - Lock after start -------------------------------------------> ON

D6 - Push-to-start ---------------------------------------------> ON

H4 - AudioVox FLRF, DEI SmartStart --------------------> ON

Everything else is OFF?

Would the car status (door, alarm, armed, disarmed, trunk, ect.) be able to communicate from the EVO-ALL to the SmartStart via data-link, with this stand alone setup?

EVo won't bypass key unless purple white wire grounded for split second

Mon, 15 Dec 2014 21:20:09 +0000

2012 Ford Edge 80bit key. Installed viper smart start and remote start. Had to do w2w because of smart start module interfering with Evo-all. Car starts in d2d mode without smart start module. When in w2w I have to ground purple/white wire for one second after initialization and release before it starts. Now the guide mentions grounding unlock wire and hooking another unlock wire to purple white but that doesn't work. Any ideas?

Vehicle shuts down when connected to smart start module

Sun, 14 Dec 2014 22:58:55 +0000

I have the settings adjusted to only the options shown, however the vehicle shuts off after a few minutes as opposed to 15 like I have set above in the options menu. When I remove the smart start module the vehicle will run perfectly. If it helps, when the smart start is in line, the locks lock and unlock. I grounded the brown wire as detailed in the pdf file, could you look at my firmware history and tell me what settings I have wrong? Thank you

Can a EVO-ALL Standalone Starter and Smart Start work together?

Sun, 14 Dec 2014 17:41:58 +0000

I have a 2013 Ford Edge SA Key. I installed an EVO-ALL as a standalone starter. Im trying to add the Smart Start Module and will NOT communicate. I want the 3xLock to work as well as the smart start module. Is this possible? Ive spent the better part of the weekend working on it and cannot get it to work for the customer. Thank you in advance. Ive tried every setting in the FLASHLINK. Ive tried cutting and grounding every wire on the smart start. No communication between the two and I remember speaking with someone at FORTIN and they said a EVO-ALL will not work 3x start and and additional remote start. Does this apply to the Smart Start as well?

2013 Ford Edge key start not starting

Sat, 13 Dec 2014 16:42:43 +0000

Wired up to directed 5x03, when attempting to remote start, red light constant blue light flickers on then off. Does not attempt remote start. Brain box clicks once then retries. Any ideas?? Does the same when wired in standalone except dash lights come on like accessory is on.

Evo One bypass settings for DEI DSM250?

Fri, 05 Dec 2014 17:11:37 +0000

Hi -

An Evo One is installed on a 2014 Tundra, and being used for remote start (3x lock), works great, awesome product! A DEI DSM250 is being installed as an extenstion onto the Evo One, and we would like to confirm the proper settings via the flash loader.

This is what we believe needs to be set on the Evo One...

Flash Loader - Bi-Pass Settings (?):

#20 - GPS / I/O (the DSM250 is GPS enabled where as the DSM200 is only "RemoteStart")

#21 - D2D

#23 Supported RF Kits Available - select #4 (DEI Smart Start)

Flash Loader - Remote Start Settings (?):

It doesn't appear I need to change any of the functions 1-39?

Thanks in advance

dei smartstart add on for standalone evoall

Wed, 06 Aug 2014 12:48:12 +0000

2014 acura rdx (or any standalone). i see it's a standalone. can i & how would i add on dei smartstart.ty. dave securely

Where can i find the diagrams for adding xl202 or smart start to evo modules

Tue, 24 Jun 2014 15:43:56 +0000

recently I saw that you can add aftermarket remotes or smart start/drone to a standalone evo module. Just wondering how to add both if possible?

can evoall connect to smartstart instead of rf kit or in conjunction

Thu, 30 Jan 2014 09:42:02 +0000

can evoall connect to smartstart instead of rf kit or in conjunction

can i add a smart start module on the evo-all on a 2010 lexus rx300

Thu, 16 Jan 2014 09:14:58 +0000

is there a data plug for the smart start module on the evo-all bypass and also does this standalone bypass controls the locks and does it has pts takeover and does it shutoff the autoheadlamps off when remote started

2013 Kia Optima SXL Viper SmartStart/EVO-ALL

Mon, 23 Dec 2013 11:06:29 +0000

I have a 2013 Kia Optima SXL and would like to use the Viper SmartStart System, specifically for the iPhone feature. Will getting the EVO-ALL be the only other necessary item or is it even necessary? Thanks.

Remote Start on a 2014 Infiniti QX60?

Wed, 11 Dec 2013 16:22:15 +0000

We have a customer that would like to have a remote start installed on his 2014 QX60. Anyone have intel on bypass for these yet? There is already a factory remote start on the vehicle, but he wants to have a Viper 4706V with SmartStart.

Is there a list of RF kits that work with EVO-ALL in stand alone?

Thu, 21 Nov 2013 15:15:50 +0000

What RF kits and cellular adapters work with the Fortin modules? Can I use Directed XL202 etc and the DSMC100/250?

The start up engine is blocked what is the probability?

Mon, 18 Nov 2013 14:57:17 +0000

I have a kia forte 2010 , suddenly appear a message ( manage the steering and push start botton) I replaced the start up locker from damaged car two times its work for a while then show same message . The item number of this spare part is 81900 - 2M000 . Do you can help me what to do.

Can the EVO-ALL be installed with a Viper VSM200 to act as a complete remote start solution for a 2013 Kia Optima SXL?

Mon, 11 Nov 2013 15:00:44 +0000

2013 Kia Optima SXL

I would like to know if the EVO-ALL can be used as a stand-alone remote start solution in conjunction with the Viper VSM200 module.

Thank you!