Questions & Answers - Questions récentes tagguées solid

Solid yellow and red light

Mon, 20 Dec 2021 17:02:59 +0000

So im installing the evo all with the tb-vw module in a 2008 vw rabbit. ive been fighting with this thing for a few hours now trying to get the thing to read the key so i can use the dcryptor. ive manage to get past the setup 3 diffrent times but each time i end up with a solid yellow and red light when i apply power back to the evo all. when i go to start it, the yellow will go off then the red starts flashing and wont stop till i unplug it. any advice would be great. also ive tried factory resetting, flashing diffrent firmwares and ive now hit the limit on dcryptor and i believe im one flash away from the limit

All 3 LEDs on EVO-FORT4 with first key in

Mon, 27 Sep 2021 13:20:01 +0000

2014 Ford Flex Std. Key w/EVO-FORT4 Soon as the fist key is inserted all 3 LED's stay lit solid...even all through 2nd key and back to the 1st key during programming. Vehicle can be put in 3rd key programming mode without module installed (door locks will cycle). Key sense wire is good, ignition chime comes on when key is inserted. Tried programming also without red plug plugged into the module. And checked with tech support using SN to make sure the module was programmed correctly. ?? Thank you.

Solid red light after downgrading firmware.

Thu, 25 Feb 2021 06:35:18 +0000

Not able to program evo 1 having solid red light

Does the Red led always need to come on 2020 Silverado 1500, Evo-one?

Mon, 18 Jan 2021 19:00:38 +0000

Hello, thanks for looking at my question. I am using an Evo one, with A GM 7 T harness in a 2020 Chevy Silverado 1500 Everything has gone pretty well I installed the T harness, attached both unlock leads to the gray BCM plug, and the tailgate/trunk lead to the pink BCM plug, double checked pins, and that looks good. The Evo1 lights up like it is supposed to, except after the step where I hit the program button 5 times under the yellow LED and turn to run, the RED Solid never comes on the first try. After failing 3 times, I expiremented and turned the key a few tries until it eventually turned red.

The steps resumed as expected I got the rapid flashing blue lights at on postion, went inside to windows computer and used the Dcrypter to record the key. that went well, no errors or issues with the fortin software. The problem is that the remote start does not work. Tried both the lockx3 and the lock+tailgate and it does not work to start car. Since the key flashed properly, and the LEDs resumed normally, is that red led lighting after the original 5 program button taps the issue, or are the 7 loose wires needing to be connected to something two greens, one blue, black, orange, orange and black wire.

I followed the wiring diagram, these 7 loose wires I find unnerving, was it inferred what to do with these wires as a profession because I am DIY and might need just a little more of an explanation.

EVO One module LED stays solid red when trying to program

Sat, 16 Jan 2021 15:10:47 +0000

2015 Toyota RAV4 Evo one regular install.

Service number 002B04111969

I am using firmware version 79.65 (Bypass) and 1.[25] (Remote Start)

When trying to program the module, I hold the programming button and when I hook the 6 pin connector to it, I get a solid red light and the light below the yellow "loop" is flashing red.

I already verified that yellow wire A1 has 0 volts

Can't get the solid blue light

Sat, 12 Oct 2019 13:17:28 +0000

Hello.

I have a 2017 Jeep Patriot, pluged the t-harness to immobilizer, connected the 4-pin connector while holding the program button and all 3 lights keep flashing. How can I get the solid blue to program.

Thank you

Can'y get blue solid blue led

Fri, 11 Oct 2019 23:13:17 +0000

2006 chevy uplander evo one can't get solid blue led in step 1 programming

Can'y get blue solid blue led

Fri, 11 Oct 2019 23:12:06 +0000

2006 chevy uplander evo one can't get solid blue led in step 1 programming

2016Q5 with push start

Sun, 10 Mar 2019 15:48:56 +0000

I got evo-one, when I finally made the setting as recommended by the installation guide:

c1, D6 and d2 and 32.6 38.2

now it attempts to start and it unlocks the car but it doesn't starts the remote won't work locking and unlocking doesn't work, the lights (blinkers) flash twice every one minute and the blue light stays on.

When I flashed with the latest version 75 something I couldn't get to program on the car the blue light never flash rapidly and it only worked on version 60 any help would be great.

Thanks